Huawei Speed Wi-Fi NEXT W01 Quick start guide

DANGER Be sure to read the following hazards before use.
If the leaked liquid gets on your skin or clothes, immediately rinse it off with water to avoid injury. If the liquid gets
into your eyes, do not rub, but after wash your eyes with water, and immediately consult a doctor to avoid the risk of
losing your eyesight. If the liquid gets on a device, wipe it off without touching it.
Internal battery is a consumable item. If the performance of an internal battery does not recover (e.g. the usable
time after each charge has become extremely short), the internal battery is at the end of service life, so stop use.
Failure to do so might cause overheating, ignition, rupture or liquid leakage. Since the battery is built-in, au Shop will
keep the product and charges will be incurred for repair. You may not use the product for a certain period. Please be
forewarned. Note that the length of service life varies depending on the usage condition, etc.
■Charging equipment
WARNING Be sure to read the following warnings before use.
Do not use at other voltages than the specified power supply voltage. Doing so might cause an ignition, fire,
overheating, electric shock, or injury.
•AC adapter: 100 – 240V AC
Firmly insert the power plug of the specified charging equipment into the power outlet down to the base of its pins.
Incomplete insertion of the power plug might result in electric shock, overheating, fire or injury. Do not use damaged
charging equipment or loose power outlets.
Do not damage, modify, twist, pull or place a heavy object on the power cable of the specified charging equipment
(sold separately). Do not use a damaged cable. Doing so might cause an electric shock, injury, short circuit or fire.
Do not let your hands, fingers and other parts of the body touch the connection terminals. Doing so might cause
electric shock, injury or a fault.
If you hear thunder, do not touch the power plug. Doing so might cause an electric shock as a result of a lightning
strike.
When cleaning, remove the specified charging equipment’s power plug from the power outlet. If the plug remains
plugged in when you clean the equipment, it might cause an electric shock or short-circuit.
Wipe off the dust on the power plug. Failure to do so might cause fire, burns or electric shock.
When not using the product for a long while, remove the specified charging equipment’s power plug from the power
outlet. Failure to do so might cause fire or a fault.
Do not use in places subject to splashing with water, pet urine or other liquids. Doing so might cause overheating, fire,
electric shock or fault from short-circuiting or corrosion of electronic circuits. In the event that the product is splashed
with liquid, immediately disconnect the specified charging equipment’s power plug.
CAUTION Be sure to read the following cautions before use.
Do not use in humid places such as bath areas, or connect/disconnect the specified charging equipment with wet
hands. Doing so might cause electric shock, injury or a fault.
Charge the battery in a stable place especially while the vibration mode set. If placed on an inclined surface or
wobbly stand, the product might fall causing injury or damage. In addition, do not cover or wrap the product with a
cloth or bedding. Doing so might cause a fire, fault or injury.
Hold the power plug of the specified charging equipment when removing from an outlet. If you pull the cable, the
cable might be damaged.
If you feel any abnormality with your skin, immediately consult a dermatologist. Itching, rashes, eczema, etc.
sometimes occurs depending on your physical constitution and condition.
The materials of parts used on the supplied AC adapter/microUSB cable (HWD14PQA) are as follows.
Part Material <Surface treatment>
Exterior case PC resin
Power plug Copper alloy <Nickel plating>
USB cable PVC resin
USB plug (Shield) Iron <Nickel plating>, PBT resin
USB plug (Resin part) PVC resin
microUSB plug (Shield) Stainless <Nickel plating>, LCP resin
microUSB plug (Resin part) PVC resin
■au Micro IC Card (LTE)
WARNING Be sure to read the following warnings before use.
Do not put the au Micro IC Card (LTE) in a cooking apparatus such as a microwave oven or a pressure vessel. Doing
so might cause melting, overheating, fuming, loss of data or a fault.
CAUTION Be sure to read the following cautions before use.
Be careful when attaching/removing the au Micro IC Card (LTE). Doing so might injure your hands or fingers.
Use only the devices specified by the Company to insert the au Micro IC Card (LTE) in. Using a device not specified
by the Company might cause loss of data or a fault. For the specified devices, contact an au shop or Customer
Service Center.
Do not disassemble or modify the au Micro IC Card (LTE). Doing so might cause loss of data or a fault.
Do not use or leave the au Micro IC Card (LTE) in hot places such as by the fire or a heater. Doing so might cause
melting, overheating, fuming, loss of data or a fault.
Do not throw the au Micro IC Card (LTE) into a fire or heat it. Doing so might cause melting, overheating, fuming, loss
of data or a fault.
Do not touch the IC (metal) part of the au Micro IC Card (LTE) or short-circuit it. Doing so might cause loss of data or
a fault.
Do not drop the au Micro IC Card (LTE) or subject it to strong impact. Doing so might cause a fault.
Do not fold, bend or place a heavy object on the au Micro IC Card (LTE). Doing so might cause a fault.
Do not wet the au Micro IC Card (LTE). Doing so might cause a fault.
Do not scratch the IC (metal) part of the au Micro IC Card (LTE). Doing so might cause a fault.
Do not store the au Micro IC Card (LTE) in dusty places. Doing so might cause a fault.
Do not store the au Micro IC Card (LTE) in places exposed to direct sunlight or hot and humid places. Doing so
might cause a fault.
Store the au Micro IC Card (LTE) out of reach of small children. Failure to do so might cause injury, etc. if they
accidentally swallow and choke on it.
Handling precautions
These precautions are provided to ensure that performance can be fully demonstrated. Thoroughly read these precautions to
ensure correct use.
■Precautions common to the main unit, charging equipment, au Micro IC Card (LTE),
peripheral devices
●
Do not apply excessive force to the product during use. Be sure not to put the product into a tightly packed bag or place
a heavy object on the product in a bag. Sitting on the product in your pocket might damage the display or internal circuit
board resulting in a malfunction.
Keeping an external device connected to the external connection might damage the connector resulting in a malfunction.
Such damage and malfunction are not covered by the warranty, even if there is no external damage.
●Do not use the product in extremely hot, cold or humid places. (Use within an ambient temperature range of 5°C to 35°C
and humidity range of 35% to 85%.)
●Do not use in places subject to lots of dust or vibration.
●Clean the connection terminals with dry cotton swabs, etc. every now and then. Soiled terminals might cause poor
connection. Do not exert a strong force to clean the connection terminals to prevent deformation.
●Clean the product with a dry soft cloth (such as the type used for eyeglasses). Forceful rubbing with a dry cloth may
scratch the display. The display may be stained if splash or smear is left attached to the surface. Wiping the product
using alcohol, thinner, benzine, detergent, etc. might erase the printing on the outer casing or cause discoloration.
●Use as far away as possible from land-line phones, TVs and radios. Use nearby might affect them.
●The product may become warm while charging or communicating, depending on the situation, but this is not abnormal.
Note that there are times when it comes to use the product in a bag or bag heat up, the temperature of the product is
increased.
●When the product is used by a child, parents or guardians should thoroughly read the “Instruction Manual” and teach the
child how to use it.
■Main unit
●Do not forcefully press, tap or intentionally subject the display to strong impact. Doing so might cause scratching or
damage.
●Do not forcefully press your fingernails, sharp objects or hard objects against keys or display surface. Doing so might
cause scratching or damage.
The touch panel is designed to be lightly touched by fingers. Do not apply strong pressure with your fingers or sharp-
pointed objects (such as fingernails, ballpoint pens and pins) on the touch panel.
In the following cases, the product may not respond to touching the touch panel, or errors in operation may occur.
•Operation with gloved hands
•Operation with fingernails
•Operation with foreign object on the screen
•Operation with protective sheet or seal on the screen
•Operation with a water drops or dew condensation attached on the touch panel
•Operation with wet or sweaty fingers
●
Never use the modified product. Use of a modified device violates the Radio Law.
This product has acquired the certification of conformity with technical regulations for the specified radio station based on
the Radio Law, and you can check “Technical Conformity Mark ” from the “Certification” screen (in Home screen, tap
“Settings”→“About”→“Certification” to display) as a certificate. If the screws of the product are removed and modifications
are made to the internal components, the certification of conformity with technical regulations will become invalid. Never
use the product without the valid certification. Doing so violates the Radio Law.
●To prevent unlawful modification, the product has been designed so that it cannot be easily disassembled. Modifying the
product is prohibited by the Radio Law.
●Contents saved in this product might be altered or lost in an accident, fault, repair or mishandling. Be sure to keep a copy
of important contents. Note that Company assumes no responsibility for any damages or lost profits resulting from altered
or lost contents.
●This product uses liquid crystal for its display. The display response speed may become slow when the ambient
temperature is low, which is due to the property of liquid crystal and not a malfunction. The display response speed will
return to normal at room temperature.
●Although the display used on the product is made using high-precision technology, some pixels (dots) might be lit or out
at all times. This is not a malfunction.
●Take care not to inconvenience people around you when you use the product in a public place.
●Take care not to place magnetized items such as magnetic cards, speakers and TV sets near the product, as it might
cause malfunction.
Putting a strong magnetism close to the product might cause false operation.
●When you put the product in your pocket or bag, take care so that the display does not come in contact with metal objects
or other hard objects, as it might cause scratching or damage. Doing so might cause scratching or damage.
●When suddenly brought into a warm place from a cold place, or when in a humid location, or when used where
temperature suddenly changes (e.g. near the air discharge port of an air conditioner), water droplets (i.e. condensation)
sometimes are formed inside the product. Note that when used under conditions such as this, the humidity might cause
corrosion or a fault.
●When wiping the display, wipe with a soft, dry cloth. Use of a moistened cloth, glass cleaner or other similar liquid might
cause a fault.
●When connecting/disconnecting an external device to/from the external connection terminal, make sure that the external
connection terminal is horizontal with the external device.
●Note that applying unnecessary force with the external connection terminal connected to the external device might cause
damage.
●Do not discard the product together with regular trash. Please cooperate in the collection of the product when it is no
longer needed to protect the environment and effectively use resources. Old products are collected at au shops and other
places.
●Insert only an au Micro IC Card (LTE) into the Micro IC Card slot on the product.
●Note that pulling strongly or applying unnecessary force with Micro IC Card slot cover might cause damage.
■Touch Panel
●Use your finger to operate the touch panel. Do not use ballpoint pens, pencils or other sharp-pointed objects. Using such
objects does not only hinder correct operation of the touch panel, but also might cause scratching or damage to the
display.
●Do not put stickers or sheets (e.g. commercially available protective films, peep prevention sheets) on the display. Doing
so might hinder correct operation of the touch panel.
●Do not operate the touch panel with fingernails. Doing so might result in split nails or jammed fingers.
●If the display surface is dirty or wet with sweat or water, it may not function correctly. In such case, wipe the display
surface with a dry, soft cloth.
●Press the touch panel strongly may cause damage or malfunction.
●When carrying the product in your pocket or bag, take care not to put the touch panel close to metals or other conductive
materials, as it might cause false operation of the touch panel.
Notes on usage
・
As an instruction manual of this product, refer to the supplied “Quick start guide”, “Notes on usage” (this guide), or “取扱説明書 詳細版 (Full
Instruction Manual)” (Japanese) available on the au homepage. In this manual, “Instruction Manual” includes “Quick Start Guide” (this manual), “Notes
on usage”, and “取扱説明書 詳細版 (Full Instruction Manual)” (Japanese).
・
In this guide, “Speed Wi-Fi NEXT W01” is referred to as the “product”.
・
All of the indicated amounts exclude tax unless otherwise specified.
Exemptions
•The Company is not liable for any damages arising from earthquakes, lighting, storms, floods or other natural disasters, as
well as fires, actions by third parties, other accidents, intentional or mistaken misoperation by the customer, or use under
other unusual conditions outside the responsibility of the Company.
•The Company is not liable for any incidental damages (change/disappearance of described content, loss of business
income, disruption of business, etc.) arising from use of or inability to use the product.
•The Company is not liable for any damages arising from failure to observe described content of the “Instruction Manual".
•The Company is not liable for any damages arising for example, from malfunction caused by combination with connected
devices or software not related to the Company.related to the Company.
•Settings etc. may sometimes be altered or lost due to faults, repair or other mishandling of the product. The Company is not
liable for any damage or lost due to faults, repair or other mishandling of the product.
•It is recommended you keep a copy of important data on your PC's hard disk Whatever the cause of the defect or
malfunction may be, the Company assumes no responsibility for alteration or loss of saved data.
•The product is used under WiMAX 2+ network environment; however, UQ Communications Inc. is not liable for quality of the
product etc.
*“The Company” as appears in this manual refers to the following companies:
Sold by: KDDI CORPORATION·OKINAWA CELLULAR TELEPHONE COMPANY
Imported by: HUAWEI Technologies Japan K.K.
Manufactured by: HUAWEI TECHNOLOGIES CO., LTD
◎Reproduction of the content of this manual in part or in whole is prohibited.
◎The content of this manual is subject to change without notice.
◎Every effort has been made in the preparation of this manual. Should you notice any unclear points, omissions, etc., feel free to contact us.
Safety Precautions (Observe Strictly)
■Before using this product, thoroughly read these “safety precautions” for proper use. After reading, store the precautions in
a safe place.
●These “Safety Precautions” describe instructions that should be observed to prevent damage to property or injury to the
customer or others using the product.
●These instructions are divided into the following categories.
■Explanation of indications used in this manual
This symbol indicates “the potential and imminent danger of death or serious injury(*1) to a
person.”
This symbol indicates “the possibility of death or serious injury(*1) to a person.”
This symbol indicates “the possibility of personal minor injury(*2) to a person or physical
damage(*3).”
*1 Serious injury: This refers to loss of sight, injury, burns (high- and low-temperature), electric shock, broken bones, injuries
with residual aftereffects from poisoning, etc., and injuries requiring hospital admission for treatment or long
term hospital attendance as an outpatient.
*2 Minor injury: This refers to injuries, burns (high- and low-temperature), electric shock, etc. that do not require hospital
admission for treatment or long-term hospital attendance as an outpatient.
*3 Physical damage: This refers to extended damage to buildings, furniture, livestock, or pets.
■Explanation of graphic symbols used in this manual
Indicates an action that is not allowed. Indicates that use in a place where the product is
likely to get wet or allowing the product to get wet is
not allowed.
Indicates that handling with wet hands is not
allowed. Indicates an action that must be done.
Indicates that disassembly is not allowed. Indicates that the power plug must be disconnected
from the power outlet.
■Precautions common to the main unit, charging equipment, au Micro IC Card (LTE),
peripheral devices
DANGER Be sure to read the following hazards before use.
Be sure to use only the specified peripheral devices. Use of other devices might cause overheating, ignition, rupture,
fault, or leakage of liquid.
Do not use, store or leave the product in hot places (e.g. by the fire, near a heater, under a kotatsu, in direct sunlight,
in a car in the hot sun). Doing so might cause ignition, rupture, fault, fire or injury.
Before entering an area where flammable gas is generated such as a gas station, be sure to turn off the product and
stop charging the battery. Failure to do so might cause the gas to catch fire.
Do not put the product in a cooking apparatus such as microwave oven or a pressure vessel. Doing so might cause
ignition, rupture, fault, fire or injury.
Do not throw the product into a fire or heat it. Doing so might cause ignition, rupture or fire.
Do not short-circuit the connection terminals. Do not allow conductive foreign objects (metal fragments, pencil leads,
etc.) to come into contact with or get inside the connection terminals. Doing so might cause fire, burns, a fault due to
heat generation.
When using a metal accessory etc., take sure not to allow the metal part come in contact with the connection
terminals or power outlet. Doing so might cause electric shock, ignition, injury or a fault.
The customer is not allowed to disassemble, modify or repair the product. Doing so might cause a fault, ignition,
electric shock, or injury. The Company is not liable even in the event of any nonconformities arising on the product or
PC as a result of modification, etc. Modification of the product is in violation of the Wireless Telegraphy Act.
WARNING Be sure to read the following warnings before use.
Do not drop or subject to strong impact, such as dropping and throwing. Doing so might cause rupture, overheating,
ignition or a fault.
Do not use outside when you can hear thunder. Doing so might risk lightning strikes and electric shock.
Do not let your hands, fingers and other parts of the body touch the connection terminals. Doing so might cause
electric shock, injury or a fault.
If the product is damaged because it is dropped or something, and its display is cracked or internal parts are
exposed, do not touch the cracked display or exposed parts with your hands. Doing so might cause electric shock or
injury from damaged parts. Contact an au shop or Keitai Guarantee Service Center.
If the wet product is charged, electric shock, short circuit, or corrosion may occur and overheating may cause fire or
malfunction or burns.
Do not splash with water or other liquids. Also, never use in places subject to direct splashing with water or pet urine,
etc. or in humid places such as bath areas, or use with wet hands. Doing so might cause electric shock or fault from
short-circuiting or corrosion of electronic circuits. In the event that the product is splashed with liquid, immediately
disconnect the specified charging equipment’s power plug and external devices. Faults caused by wetting with water
or humidity are not covered by the warranty and charges will be incurred for repair.
Do not operate the product while driving an automobile or motorized bicycle, riding a bicycle or walking. Doing so
may compromise traffic safety and cause an accident.
If charging is not completed after the specified charging time, stop charging. Failure to do so might cause leakage of
liquid, overheating, rupture or ignition.
Do not leave in places within the reach of small children. Small children might swallow small parts, etc. by mistake
and choke on them, or might drop them by mistake and cause accidents or injury.
CAUTION Be sure to read the following cautions before use.
Do not store the product in places subject to direct sunlight (e.g. in automobiles), places that get hot, places that get
extremely cold, and in humid or dusty places. Doing so might cause overheating, ignition, deformation or a fault.
Do not leave on unstable places such as rocky stands or tilting surfaces. Dropping the product may cause injury or
damage. Also, pay sufficient attention to impact, etc.
Do not cover or wrap the product with bedding, etc. while using or charging the product. Doing so might cause a
fire, fault or injury.
Do not touch the main unit or specified charger for a long time while power is being supplied from an external
source. Doing so might cause low-temperature burns.
The product may become hot by prolonged use especially in high-temperature environment. Be careful when using
the product touching your skin for a long time, as it might cause low-temperature burns.
Do not use power outlets or wiring apparatus beyond its rating. Also, exceeding rating, for example, by connecting
multiple devices to a single power strip might cause overheating and fire.
Do not place near corrosive chemicals or in places where corrosive gas is generated. Doing so might cause a fault
or loss of internal data.
Do not leave or store with the Micro IC Card slot cover opened. Doing so might allow dust or other foreign objects to
get inside and cause a fault.
Do not use if there is smoke, abnormal odor or noise, excessive overheating, or other abnormalities. While charging,
disconnect the specified charging equipment, make sure that the product is not overheating, and power off the
product, then contact an au shop or Keitai Guarantee Service Center. Also, if you have dropped or damaged the
product, do not continue to use it in that state, and contact an au shop or Keitai Guarantee Service Center.
When using the specified AC adapter or external device, insert/remove the connector straight to/from the terminal.
Make sure the orientation of the connector is correct. Unless it's correct, it may cause damage or a fault.
Do not charge the battery with W01 Cradle (HWD31PUA) (sold separately) when a cover or case are attached to the
product. Doing so might cause failure of charging, overheating, ignition, or malfunction.
■Main unit
WARNING Be sure to read the following warnings before use.
Do not use the product while driving a car or riding a motorbike or bicycle. It may cause a traffic accident. Use of
the product while driving a car or motorbike is prohibited by law. Use of the product while riding a bicycle may be
punishable by some regulations.
Use of electric devices on board is restricted. Follow the instructions of each airline company. Failure to do so may
adversely affect on-board electronic equipment. Doing prohibited use of the electric devices in an aircraft may be
punishable by law.
Follow the instructions of each medical facility for the use of the product on their premises. Failure to do so may
affect electronic equipment and electronic medical equipment.
The product sometimes affects high-precision electronic devices. So, turn it off near such devices. (Examples of
electronic devices that might be affected by the product include cardiac pacemakers, hearing aids, other electronic
medical devices, fire alarms, and automatic doors. If you are using an electronic medical device, contact the device
manufacturer or retailer for information about the possible affect of radio waves.)
When using the product near an implanted pacemaker, implanted cardioverter-defibrillator or other electronic
medical device, radio waves might affect these units and devices. So, please observe the following.
1. Those with an implanted pacemaker or implanted cardioverter-defibrillator should carry or use the product at least
15cm away from the pacemaker or cardioverter-defibrillator.
2. Turn the product off when it may be difficult to keep at least 15cm away such as in a situation you cannot move
freely, since there may be people with a cardiac pacemaker or implanted cardioverter-defibrillator nearby.
3. When a medical institution has laid down designated areas where use of the product is prohibited or is not
allowed to be brought in, abide by the instructions of that medical institution.
4. When using electronic medical devices other than an implanted pacemaker and implanted cardioverter-
defibrillator outside a medical institution (e.g. home medical treatment), check individually with the manufacturer
of the electronic medical device regarding the influence of radio waves.
CAUTION Be sure to read the following cautions before use.
Use of the product in an automobile sometimes affects on-vehicle electronic devices, though this rarely happens. If
this happens, stop use since this may impair safe travel.
If you feel any abnormality with your skin, immediately consult a dermatologist. Itching, rashes, eczema, etc.
sometimes occurs depending on your physical constitution and condition.
The materials of parts used on the product are as follows.
Part Material <Surface treatment>
Display panel (Touch panel) Glass
Exterior case PC resin <coating>
Power button PC resin <coating> TPU resin
Micro IC Card slot cover Outside: PC resin <coating> Inside: TPU resin
Do not allow liquids, metal pieces, burnable items, and other foreign matter to get inside the external connection
terminal and Micro IC Card slot. Doing so might cause fire, electric shock, a fault or injury.
Use the product with the Micro IC Card slot cover closed. If the covers are open, dirt or water may get inside
causing a fault.
Do not put the product directly on sand at a beach, etc. Sand or other small particles might get inside the product
through the external connection terminal causing overheating or a fault.
When using the product for data communication, be careful not to keep the product in direct contact with your skin
for a prolonged period, or not to cover the product with paper, cloth, bedding, etc. The main unit might get hot,
causing fire, injure, burns or a fault.
■Internal Battery
(The internal battery of the product is a lithium-ion battery)
The internal battery is not fully charged at the time of purchase. Charge the battery before using the
product.
DANGER
WARNING
CAUTION

■Internal Battery
●Use in very hot or cold environments, for example, when left in an automobile with the windows closed in summer, will
cause the internal battery capacity to drop and shorten the available battery usage time. That also shorten the internal
battery life. Try to use the internal battery as far as possible at room temperature.
●Charge the battery before using the product for the first time after purchase, or if you have not used the product for a long time.
●Internal battery is a consumable item. If the performance of an internal battery does not recover, the internal battery is
at the end of service life, so stop use. Since the battery is built-in, au Shop will keep the product and charges will be
incurred for repair. You may not use the product for a certain period. Please be forewarned. Note that the length of service
life varies depending on the usage condition, etc.
●Internal battery sometimes swell up as they approach the end of their service life. This is due to the properties of lithium-
ion batteries, and is not a problem in terms of safety.
■Charging equipment
●
When not using the product, remove the specified charging equipment’s power plug from the power outlet.
●
Do not wrap the microUSB cable of specified charging equipment around the power plug or W01 Cradle (HWD31PUA) (sold
separately). Doing so might cause electric shock, fault, injury, overheating or fire.
●
Do not forcibly bend the specified charging equipment's plug or the connection between the connector and microUSB
cable. Doing so might cause electric shock, fault, injury, overheating or fire.
●
Charging may not be available due to protection function because temperature of environment is high or low. Charge the
battery in a place where an ambient temperature range of 5°C to 35°C.
■au Micro IC Card (LTE)
●
The au Micro IC Card (LTE) is lent to you by au. In case of loss or damage, the card will be replaced at your expense. When
malfunction is suspected, or in case of theft or loss, contact an au shop or PiPit.
●
Do not forcibly remove or insert the au Micro IC Card (LTE). Be careful not to exert excessive force when inserting the card
into the product.
●
You are responsible for any damage caused by inserting your au Micro IC Card (LTE) into some other IC card reader, etc.
●
Keep the IC (metal) part of your au Micro IC Card (LTE) clean. For cleaning the au Micro IC Card (LTE), wipe it with a dry,
soft cloth (such as for cleaning eyeglasses).
●
Do not put stickers, etc. on the au Micro IC Card (LTE).
●
Do not insert IC Card with a conversion adapter. Doing so may cause a fault.
■Copyrights & portrait rights
●You are not allowed to copy, distribute, publish, modify or edit the data you downloaded using this product without the
consent of the copyright holder, except for personal use, under the copyright law.
In addition, do not use or modify portraits or names of other individuals without their consent, as it might infringe on rights
of portrait.
■Backup content on the product
●
Please back up important content downloaded for the product. Content recorded to memory on the product sometimes
disappears or is altered by unexpected factors, such as static electricity or a fault, repair, mishandling, etc.
* How to make backups: you can back up setting contents of the product in your PC. Please refer to “取扱説明書 詳細
版(Full Instruction Manual)” (Japanese). Note, however, that there are some data that cannot be copied by using these
means. Please be forewarned.
PIN code
■PIN code
●
To prevent unauthorized use of the au Micro IC Card (LTE) by a third party, you can set the product to require PIN code entry
every time the power is turned on. You also need to enter PIN code when setting whether the PIN code entry is required.
●
If the PIN code is incorrectly entered three times consecutively, the PIN code will be locked. You can unlock the PIN code
using PUK code.
*PIN code is “1234” and PIN code entry was set to not be required at the time of purchase. You can change PIN code to
any four- to eight-digit number, and set the PIN code entry to be required as necessary.
*PIN code cannot be reset by initializing the product.
■PUK code
●In case the PIN code is locked, you can unlock it by entering the PUK code.
*PUK code is an eight-digit number given at the time of purchase, which is printed on the back side of the plastic card on
which your au Micro IC Card (LTE) is attached.
*After entering the PUK code, you need to set a new PIN code in “PIN management”.
*If the PUK code is incorrectly entered ten times consecutively, contact an au shop, PiPit or Customer Service Center.
Notes on the supplied software
Pay attention to the following points when using the software supplied with the product
●The software is licensed to you for use only. Copyright of the software is not transferred to you. You may not transfer or sell
the software to any third parties.
●You may copy the software for backup purpose only. You may not copy the software for the purpose of transferring or
selling to others.
●The Company is not liable for any loss arising by using the software or claim for damages against you from the third party.
Notes on using Bluetooth®/Wireless LAN functions
•The Bluetooth®function and Wireless LAN function of this product conforms to domestic wireless standards in Japan, FCC
standards and EC Directives, and have been certified.
•Use the 5 GHz band wireless LAN function of the product in Japan. The 5 GHz band wireless LAN function of this product
conforms to domestic wireless standards in Japan, and has been certified. Use overseas may be subject to punishment by
law.
•The 2.4 GHz band used by wireless LAN or Bluetooth®devices is operated by various other devices. For this reason, the
communication speed and connectable range may be decreased, or disconnection may occur, due to interference by other
devices.
•Do not use this product in places where electromagnetic waves are generated or near electric products, AV and OA
equipment, or other magnetized devices.
•Subjecting this product to magnetic or electrical noise might increase noise and prevent it from performing communications.
(This product is particularly susceptible to noise when it used near a microwave oven.)
•Using this product near a TV, radio or similar appliance might cause reception interference and disrupt TV images.
•Searching might not be successful if there are multiple wireless LAN access points near to the product or the same channel
is being used.
•Use of electric devices on board is restricted. Follow the instructions of each airline company.
•The communication speed and connectable range vary depending on the distance between communication devices,
obstacles and the devices used.
Cautions on using 2.4 GHz band
Bluetooth®function/Wireless LAN function of this product uses 2.4 GHz band. In this frequency band, other similar wireless
stations, in-plant wireless stations for mobile unit identification that require a license for use, such as factory production lines,
specific small power wireless stations that do not require licenses, amateur wireless stations (collectively called “other wireless
stations” from here on) are operated in addition to home electrical appliances such as microwave ovens, devices for industrial,
scientific and medical devices.
*The product cannot perform data communication using Bluetooth®function.
1. Before using this product, make sure that “other wireless stations” are not in operation nearby.
2. In the event that instances of radio wave interference have occurred between this product and “other wireless stations”,
immediately either relocate this product or stop operation of the device (stop emission of radio waves).
3. If you are unclear on any points or are troubled by anything, contact an au shop or Customer Service Center.
•Connections between this product and all Bluetooth®/wireless LAN devices have not been confirmed. Therefore,
connections with all Bluetooth®/wireless LAN devices are not guaranteed.
•This product supports security features for wireless communications that are compliant with the wireless LAN standard
specifications, but the security may not be sufficient depending on the usage environment and configuration. Be careful
when making data communication using wireless LAN function.
•Wireless LAN has the advantage that it can be freely connected anywhere within the radio wave range, as it uses radio
waves for exchanging information. At the same time, there is a risk that a malicious third party may obtain unauthorized
access if security settings have not been configured. You are recommended to configure security settings before using
wireless LAN at your decision and responsibility.
•The Company assumes no responsibility for leakage of data or information that may occur during wireless LAN
communication.
•Since Bluetooth®and wireless LAN functions use the same frequency band, using the both functions at the same may cause
radio wave interference resulting in decreased communication speed or disconnection from the network. If connection fails,
stop using either of the Bluetooth® and wireless LAN functions.
Bluetooth®function/Wireless LAN function of this product uses 2.4 GHz band.
2.4FH1/DS4/OF4
•Bluetooth®function
This product uses the 2.4 GHz band. FH-SS is used as the modulation scheme for FH1. The interference distance is about
10 m or less. This means that all bandwidths are used, and that bands of mobile unit identification devices can be avoided.
•Wireless LAN function
This product uses the 2.4 GHz band. DS-SS and OFDM are used as the modulation schemes. The interference distance is about
40 m or less. This means that all bandwidths are used, and that bands of mobile unit identification devices can be avoided.
Available channels differ depending on the country.
For use in an airplane, check with the airline company in advance.
Cautions on using 5 GHz band
•Check that your wireless LAN device is compatible with wireless LAN 5 GHz band. The product cannot be connected with
wireless LAN 5 GHz band and 2.4 GHz band at the same time. If your wireless LAN device is not compatible with 5 GHz
band, change the product setting to 2.4 GHz band to use.
•For wireless LAN 5 GHz band, use of W56 channel outdoor is available but use of W52/W53 channel outdoor is prohibited.
When is displayed on the screen, use the product indoor.
•When using wireless LAN 5 GHz W53/W56 channel, the channel may be changed automatically to avoid radio wave
interference by weather radar etc. In that case, communication interrupts (DFS function).
After-sales service
■When asking for repair
For repair, contact Keitai Guarantee Service Center.
During the warranty period Repairs will be done based on the terms of services of the free-of-charge repair warranty
described on the warranty card.
Outside the warranty period We shall repair the product for a charge as requested by the customer if repair renders it
usable.
•Before handing in the product for repair, make a backup of the contents of memory since they may disappear during repair. Note
that the Company shall not be liable for any damages and loss of income should the contents of memory be altered or lost.
•Recycled parts that meet the Company's quality standards are sometimes used for repair.
•Collected au products by Replacement product delivery service which you used before are recycled to products for
replacement after repairs. Also replaced parts by au after-sales service are collected and recycled by KDDI. They are not
returned to customers.
■Performance parts for repair
The Company retains performance parts for repair of Speed Wi-Fi NEXT W01 main unit and its peripherals for four years after
discontinuation of production.
“Performance parts for repair” refers to parts required for maintaining the functions of the product.
■Warranty card
At the store of purchase, thoroughly check and read the name of the retailer, date of purchase and other necessary details
filled in on the warranty card, and be sure to keep it in a safe place.
■Keitai Guarantee Service Plus LTE
An after-sales service membership program on a monthly basis called “Keitai Guarantee Service Plus LTE” (monthly fee:
380 yen excluding tax) is available for using your au product for a long time without worries. This service expands coverage
for many troubles including malfunction, theft and loss. For details of this service, refer to au homepage or contact Keitai
Guarantee Service Center.
•You can apply for membership only at the time of purchasing your au product.
•Once you cancel the membership, you cannot reapply for it until you purchase an au product next time.
•Note that when changing the model or purchasing an extra au product, this service only covers the most recently purchased
au product.
•When an au product is handed over to you or someone else, the Keitai Guarantee Service Plus LTE membership is also
handed over to the successor of the product.
•When you get a new au product by changing the model or purchasing an extra product, the “Keitai Guarantee Service
Plus” / “Keitai Guarantee Service Plus LTE” membership for the old au product is automatically canceled.
•Service contents are subject to change without notice.
■au Micro IC Card (LTE)
The au Micro IC Card (LTE) is lent to you by au. In case of loss or damage, the card will be replaced at your expense. When
malfunction is suspected, or in case of theft or loss, contact an au shop or PiPit.
■After-sales service
If you are unsure about anything regarding after-sales service, contact the following service contact.
Customer Service Center (for service canceling procedure in case of loss, theft or theft)
From a land-line phone,
From fixed-line phones:
0077-7-113
From au cell phones:
113 without area code
For loss, theft or damage
(toll-free)
In case above numbers are not available, call (toll-free)
0120-977-033
(except Okinawa)
0120-977-699
(Okinawa)
Keitai Guarantee Service Center
For loss, theft, damage (toll-free)
From fixed-line phones/au cell phones,
0120-925-919
Business hours : 9:00-21:00 (7 days a week)
Business hours : 9:00-20:00 (7 days a week) Business hours : 24 hours (7 days a week)
Customer Service Center
Pressing “zero” will connect you to an operator,
after calling “157” on your au cell phone.
From fixed-line phones:
0077-7-111
From au cell phones:
157 without area code
For general information, charge and
operation information (toll-free)
0077-7-113 (toll-free)
From an au cell phone, 113 (toll-free)
Business hours: 24 hours (7 days a week)
Keitai Guarantee Service Center (for loss, theft, damage)
From a land-line phone/au cell phone,
From fixed-line phones:
0077-7-113
From au cell phones:
113 without area code
For loss, theft or damage
(toll-free)
In case above numbers are not available, call (toll-free)
0120-977-033
(except Okinawa)
0120-977-699
(Okinawa)
Keitai Guarantee Service Center
For loss, theft, damage (toll-free)
From fixed-line phones/au cell phones,
0120-925-919
Business hours : 9:00-21:00 (7 days a week)
Business hours : 9:00-20:00 (7 days a week) Business hours : 24 hours (7 days a week)
Customer Service Center
Pressing “zero” will connect you to an operator,
after calling “157” on your au cell phone.
From fixed-line phones:
0077-7-111
From au cell phones:
157 without area code
For general information, charge and
operation information (toll-free)
0120-925-919 (toll-free)
Business hours 9:00-21:00 (7 days a week)
Online Repair Desk (24 hours a day over the Internet)
*Available only from PCs or smartphones
https://cs.kddi.com/support/n_login.html
• TheApplicationfortheInternetacceptance,if“damage”,“wet”,“theft”and“loss”areeligible.Inthecaseof
spontaneous failure (not the cause damage, such as water wet, but does not power on, the screen does not
function or other), it will be accepted by phone for interview is required.
• ToapplyfortheInternet,youneedthee-mailaddress.
■au after-sales service information
Service Keitai Guarantee Service Plus LTE
Member Others
Replacement cell phone
delivery service
Spontaneous
failure
1st year Free of charge
No recompense
2nd year or later Customer charge
1st: 5,000 yen
2nd: 8,000 yen
Partially damage, water soak,
irreparable damage, theft or loss
Holding over and repair
Spontaneous
failure
1st year Free of charge Free of charge
2nd year or later Free of charge
(for 3 years)
Actual costPartially damage Customer charge
Upper limit: 5,000 yen
Water soak, irreparable damage Customer charge
10,000 yen
Loss, theft No recompense No recompense
(model change)
*Charge amounts are all tax-excluded.
Replacement cell phone delivery service
•When you have trouble with your au product, replacement product (same model, same color) is delivered by calling to.
Return your damaged product within 14 days after the replacement of the product is delivered.
•Available up to twice in a year from the day you use this service as a start day. If you do not use this service in the past year
for the subscription to this service, it will be 1st and if you use, it will be the 2nd.
*For details, refer to au homepage.
Holding over and repair
•Damages and malfunctions intentionally caused by the customer as well as those due to modification (e.g. disassembly,
change of parts, painting, etc.) by the customer are not covered by this service.
•You cannot receive a refund for the replacement of the outer casing due to stains, scratches, paint removal, etc. on the
outer casing.
Specific Absorption Rate (SAR) of Mobile Terminals
This model Speed Wi-Fi NEXT W01 device complies with Japanese technical regulations and international guidelines
regarding exposure to radio waves.
This device was designed in observance of Japanese technical regulations regarding exposure to radio waves(*) and limits
to exposure to radio waves recommended by a set of equivalent international guidelines. This set of international guidelines
was set out by the International Commission on Non-Ionizing Radiation Protection (ICNIRP), which is in collaboration with
the World Health Organization (WHO), and the permissible limits include a substantial safety margin designed to assure the
safety of all persons, regardless of age and health condition.
The technical regulations and international guidelines set out limits for radio waves as the Specific Absorption Rate, or SAR,
which is the value of absorbed energy in any 10 grams of tissue over a 6-minute period. The SAR limit for mobile terminals is
2.0 W/kg. The highest SAR value for this device when tested for intended use described in the instruction manual is
0.378W/kg (*). There may be slight differences between the SAR levels for each product, but they all satisfy the limit.
The actual SAR of this device while operating can be well below that indicated above. This is due to automatic changes to the
power level of the device to ensure it only uses the minimum required to reach the network. Therefore in general, the closer
you are to a base station, the lower the power output of the device.
During communication, please keep the device farther than 1.5 cm away from your body without including any metals. This
device satisfies the technical regulations and international guidelines.
The World Health Organization has stated that “a large number of studies have been performed over the last two decades
to assess whether mobile phones pose a potential health risk. To date, no adverse health effects have been established as
being caused by mobile phone use.”
Please refer to the WHO website if you would like more detailed information.
http://www.who.int/docstore/peh-emf/publications/facts_press/fact_english.htm
Please refer to the websites listed below if you would like more detailed information regarding SAR.
○Ministry of Internal Affairs and Communications Website:
http://www.tele.soumu.go.jp/e/sys/ele/index.htm
○Association of Radio Industries and Businesses Website:
http://www.arib-emf.org/index02.html (in Japanese only)
○HUAWEI TECHNOLOGIES CO., LTD. homepage:
http://consumer.huawei.com/jp/mobile-broadband/support/information/hwd31-jp.htm
○au homepage:
http://www.au.kddi.com/
Technical regulations are defined by the Ministerial Ordinance Related to Radio Law (Article 14-2 of Radio Equipment
Regulations).
Disposal and recycling information
This symbol (with or without a solid bar) on the device, batteries (if included), and/or the packaging, indicates
that the device and its electrical accessories (for example, a headset, adapter, or cable) and batteries should not
be disposed of as household garbage. These items should not be disposed of as unsorted municipal waste and
should be taken to a certified collection point for recycling or proper disposal.
For more detailed information about device or battery recycling, contact your local city office, household waste
disposal service, or retail store.
Disposal of the device and batteries (if included) is subject to WEEE Directive Recast (Directive 2012/19/EU) and Battery
Directive (Directive 2006/66/EC). The purpose of separating WEEE and batteries from other waste is to minimize the potential
environmental impacts and human health risk of any hazardous substances that may be present.
Reduction of hazardous substances
This device is compliant with the REACH Regulation [Regulation (EC) No 1907/2006] and RoHS Directive Recast (Directive
2011/65/EU). Batteries (if included) are compliant with the Battery Directive (Directive 2006/66/EC). For up-to-date information
about REACH and RoHS compliance, please visit the web site http://consumer.huawei.com/certification.
EU regulatory conformance
■RF exposure requirements
Important safety information regarding radio frequency (RF) radiation exposure:
RF exposure guidelines require that the device be used at a minimum of 1.5 cm from the human body. Failure to observe this
guideline may result in RF exposure exceeding limits.
■Certification information (SAR)
This device meets guidelines for exposure to radio waves.
Your device is a low-power radio transmitter and receiver. As recommended by international guidelines, the device is
designed not to exceed the limits for exposure to radio waves. These guidelines were developed by the International
Commission on Non-Ionizing Radiation Protection (ICNIRP), an independent scientific organization, and include safety
measures designed to ensure the safety of all users, regardless of age and health.
The Specific Absorption Rate (SAR) is the unit of measurement for the amount of radio frequency energy absorbed by the
body when using a device. The SAR value is determined at the highest certified power level in laboratory conditions, but the
actual SAR level during operation can be well below the value. This is because the device is designed to use the minimum
power required to reach the network.
The SAR limit adopted by Europe is 2.0 W/kg averaged over 10 grams of tissue, and the highest SAR value for this device
complies with this limit.
■Statement
Hereby, Huawei Technologies Co., Ltd. declares that this device is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
For the declaration of conformity, visit the web site http://consumer.huawei.com/certification.
The following marking is included in the product:
0197
This device may be operated in all member states of the EU.
Observe national and local regulations where the device is used.
This device may be restricted for use, depending on the local network.
Restrictions in the 2.4 GHz band:
Norway: This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund.
Restrictions in the 5 GHz band:
WLAN function of this device is restricted only to indoor use when operating in the 5150 to 5350 MHz frequency range.
FCC Regulatory Compliance
■RF exposure requirements
Important safety information regarding radio frequency (RF) radiation exposure:
RF exposure guidelines require that the device be used at a minimum of 1 cm from the human body. Failure to observe this
guideline may result in RF exposure exceeding limits.
■Certification information (SAR)
This device is also designed to meet the requirements for exposure to radio waves established by the Federal
Communications Commission (USA).
The SAR limit adopted by the USA is 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported to the FCC
for this device type complies with this limit.
■FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Caution: Any changes or modifications to this device not expressly approved by Huawei Technologies Co., Ltd. for
compliance could void the user's authority to operate the equipment.
Restrictions in the 5 GHz band:
Within the 5.15 to 5.25 GHz band, UNII devices will be restricted to indoor operations to reduce any potential for harmful
interference to co-channel Mobile Satellite System (MSS) operations.
■FCC ID
Check FCC ID in the following steps.
“Settings”→“About”→“Certification”
Export Administration Regulations
This product and its accessories may be subject to the Japan Export Administration Regulations (“Foreign Exchange
and Foreign Trade Law” and its related laws). In addition, U.S. Re-export Regulations (Export Administration Regulations)
may apply to this product and its accessories. To export and re-export this product and its accessories, take the required
measures on your responsibility and at your expenses. For details on the procedures, contact the Ministry of Economy, Trade
and Industry or the U.S. Department of Commerce.
Trademarks
Wi-Fi®, Wi-Fi Alliance®, Wi-Fi CERTIFIED®, WPA™, WPA2™, Wi-Fi Protected Setup™ logos are registered trademarks or
trademarks of Wi-Fi Alliance.
•The Bluetooth word mark and logo are registered trademarks owned by the Bluetooth® SIG, Inc., and HUAWEI
TECHNOLOGIES is licensed to use these trademarks.
HUAWEI are registered trademarks or trademarks of HUAWEI TECHNOLOGIES CO., LTD. in China.
Other company names and product names referred to in this manual are trademarks and registered trademarks of
respective companies. ® or TM mark may be omitted in this manual
For inquiries, call
From fixed-line phones:
0077-7-113
From au cell phones:
113 without area code
For loss, theft or damage
(toll-free)
In case above numbers are not available, call (toll-free)
0120-977-033
(except Okinawa) 0120-977-699 (Okinawa)
Keitai Guarantee Service Center
For loss, theft, damage (toll-free)
From fixed-line phones/au cell phones,
0120-925-919
Business hours : 9:00-21:00 (7 days a week)
Business hours : 9:00-20:00 (7 days a week) Business hours : 24 hours (7 days a week)
Customer Service Center
Pressing “zero” will connect you to an operator,
after calling “157” on your au cell phone.
From fixed-line phones:
0077-7-111
From au cell phones:
157 without area code
For general information, charge and
operation information (toll-free)
December 2014, 1st Edition
KDDI CORPORATION·OKINAWA CELLULAR TELEPHONE COMPANY
Imported by: HUAWEI Technologies Japan K.K.
Manufactured by: HUAWEI TECHNOLOGIES CO., LTD