Huawei HG531 V1 User manual

HG531 V1 300Mbps Wireless ADSL2+ Router
User Guide

i
Contents
1 Product Overview
1 Supported Features
2 Ports and Buttons
3 Indicators
2 Hardware Installation
5 Selecting an Installation Location
5 Connecting Cables
6 Powering On
3 Setting Network Parameters
6 Setting the Computer IP Address
7 Logging In to the Web Management Page
7 Setting Dial-Up Connection Parameters
4 Wireless Connection Setup
10 Enabling and Disabling the WLAN on the HG531 V1
10 Setting Up a Wireless Connection Using the WPS Button
10 Manually Setting Up a Wireless Connection
12 Changing Your WLAN Name and Password
5 Maintenance Guide
12 Changing the Web Management Page User Name and Password
12 Restoring Default Settings
6 FAQs
14 What Can I Do If I Cannot Open the Web Management Page?
14 What Can I Do If the HG531 V1 Cannot Access the Internet through a Wireless Network
Adapter Sometimes or If the WLAN Connection Is Unsteady?
14 What Can I Do If I Cannot Access the Internet?
16 I Often Need to Restart the HG531 V1 to Display Web Pages. What Can I Do?
7 Appendix
17 Technical Specifications
18 Default Settings

1
1 Product Overview
Supported Features
The HG531 V1 300Mbps Wireless ADSL2+ Router (HG531 V1 for short) is a high-speed wireless router
designed for home and small office use. This chapter describes the features supported by the HG531 V1.
• Digital subscriber line (DSL) provides rugged stability, and with the WPS button, zero configuration is
required for connections to multiple devices.
• Network range allows any device in a home to be connected with a transmission rate of up to 300Mbps .
• A powerful firewall is provided with a flexible network configuration and quality of service (QoS)
strategy, enabling different home devices to enjoy high-speed and high-quality broadband services.
High-Bandwidth DSL Connectivity
The HG531 V1 incorporates a high-performance ADSL2+ processor and provides high-speed Internet
access and abundant services to be delivered through the digital subscriber line (DSL).
Routing
The HG531 V1 supports routing. It can obtain an IP address through PPP dial-up or Dynamic Host
Configuration Protocol (DHCP), which provides simultaneous access for multiple devices.
WLAN
The HG531 V1 supports multiple WLAN protocols, including 802.11b/g/n (2.4 GHz). Adopting 802.11n
multiple-input multiple-output antennas (MIMO) technology, the HG531 V1 delivers a wireless
transmission rate of up to 300Mbps with its dual antennas. In addition, the HG531 V1 supports multiple
wireless encryption modes to provide a secure, reliable, and high-speed WLAN.
Wi-Fi Protected Setup
You can set up wireless connections between the HG531 V1 and Wi-Fi enabled devices by pressing the
Wi-Fi Protected Setup (WPS) button.
Firewall
The powerful built-in firewall effectively protects against viruses and malicious attacks.
ARP Attack Protection
You can bundle an IP address and MAC address bi-directionally, which effectively protects your LAN
from Address Resolution Protocol (ARP) attacks.
Easy Configuration and Management
The HG531 V1 provides password-protected web-based management pages to protect your personal data.

2
Ports and Buttons
No. Item Description
1Reset
Restores the HG531 V1 to its default settings after you press and
hold this button for 6 seconds or more while the HG531 V1 is
powered on.
Caution
A reset will result in all custom data and settings being lost. Use
with caution.
2On/Off Powers the HG531 V1 on or off.
3Power Connects to a power adapter.
4LAN4~LAN1 Connects to Ethernet devices, such as computers, set-top boxes
(STBs), and switches.
5ADSL Connects to a DSL filter or phone socket.
6WLAN/WPS
• Enables or disables the WLAN function.
Press this button (more than 3 seconds) to enable the WLAN function.
• Starts Wi-Fi protected setup (WPS) negotiation.
Press this button (less than 3 seconds) to start WPS negotiation.
1
2
345
WLAN/
6
WPS

3
Indicators
Indicator Status Description
Power Steady green The HG531 V1 is powered on.
Off The HG531 V1 is powered off.
ADSL
Blinking green A DSL connection is being activated.
Steady green A digital subscriber line (DSL) connection has been set
up and activated.
Off
No DSL connection has been set up, or the DSL
connection is faulty.
The HG531 V1 is powered off.
Internet
Blinking green The HG531 V1 is connected to the Internet in router
mode, and data is being transmitted.
Steady green The HG531 V1 is connected to the Internet in router
mode, but no data is being transmitted.
Off
• The HG531 V1 is in router mode, but not connected to the
Internet.
• The HG531 V1 is in bridge mode.
The HG531 V1 is powered off.


4
WLAN
Blinking green The HG531 V1 has WLAN enabled, and data is being
transmitted.
Steady green The HG531 V1 has WLAN enabled, but is not
transmitting data.
Off WLAN is disabled.
The HG531 V1 is powered off.
WPS
Blinking green
The HG531 V1 is connected to a wireless client, such as
a computer with a wireless network adapter, over the
WLAN using the Wi-Fi Protected Setup (WPS)
function.
The WPS indicator blinks for 120 seconds or less.
Steady green
The HG531 V1 is attempting to connect to a wireless
client over the WLAN using the WPS function.
The WPS indicator is steady on for 300 seconds, and
then turns off.
Off WPS is disabled.
The HG531 V1 is powered off.
LAN1~LAN4
Blinking green The LAN port is connected to an Ethernet device with a
network cable, and data is being transmitted.
Steady green
The LAN port is connected to an Ethernet device (such
as a computer) with a network cable, but no data is
being transmitted.
Off The LAN port is not connected to any Ethernet device.
The HG531 V1 is powered off.

5
2 Hardware Installation
Selecting an Installation Location
Place the HG531 V1 on a well-ventilated even surface without exposure to direct sunlight. For the best
possible performance, take note of the following:
• Make sure there are no obstacles, such as concrete or wooden walls, between the computer and HG531 V1 .
• Ensure that the computer and HG531 V1 are far from electric appliances that generate strong magnetic or
electric fields, such as microwave ovens.
Connecting Cables
If you have subscribed to digital subscriber line (DSL) broadband, you can connect the HG531 V1 to a
telephone port for Internet access.
Follow the steps in the following figure to connect devices properly.
1 Telephone wall jack 2 Splitter 3 Telephone
4 Desktop computer 5 Power adapter 6 Set-top Box
7 Laptop computer 8 Smart Phone 9 Pad
a LINE port b MODEM port c PHONE port
MODEM
PHONE
LINE
1
23
4
5
6
7
8
9
a
b
c

6
When configuring the HG531 V1 for the first time, use an Ethernet cable to connect the HG531 V1
to a computer.
Powering On
To power on the HG531 V1, press its power button.
After the HG531 V1 is powered on, the HG531 V1 indicator turns on. If the indicators do not behave as
expected, ensure that everything is plugged in correctly.
3 Setting Network Parameters
Setting the Computer IP Address
Before logging in to the HG531 V1 web management page, set the IP address of the computer that will
be used for the login.
On Windows 7
1. Choose Start > Control Panel > Network and Internet > Network and Sharing Center .
2. Choose Change adapter settings . Right-click Local Area Connection and choose Properties .
3. Double-click Internet Protocol Version 4 (TCP/IPv4) .
4. Select Obtain anIP address automatically and Obtain DNS server address automatically . Click OK .
On Windows Vista
1. Choose Start > Control Panel > Network and Internet > Network and Sharing Center .
2. Choose Managenetworkconnections . Right-click the connection that you want to change, and then click
Properties .
3. Double-click Internet Protocol Version 4 (TCP/IPv4) .
4. Select Obtain anIP address automatically and Obtain DNS server address automatically . Click OK .
On Windows 8
1. Choose Settings > Control Panel > Network and Internet > Network and Sharing Center .
2. Choose Change adapter settings . Right-click the connection that you want to change, and then click
Properties .
3. Select Internet Protocol Version 4 (TCIP/IPv4) , and click Properties .
4. Select Obtain anIP address automatically and Obtain DNS server address automatically . Click OK .

7
On MAC OS X
1. Choose System Preferences > Network > Advanced .
2. Click AirPort , and choose Advanced in the lower right corner.
3. Click TCP/IP tab.
4. Select Automatically in Configure IPv4 , and click OK .
5. Click Apply .
Logging In to the Web Management Page
The HG531 V1 provides an intuitive web management page where you can view or set the HG531 V1
parameters.
Before you log in to the HG531 V1 web management page, ensure that the computer used for the login is
connected to the HG531 V1 and has been configured to automatically obtain an IP address or assigned
with a static IP address.
1. Open a browser. In the address box, enter 192.168.1.1 . Press Enter .
2. Enter the login user name ( user by default) and password ( @User1234 by default). Click Login .
To protect against unauthorized access, change the user name and password after the first login.
Setting Dial-Up Connection Parameters
The HG531 V1 works in bridge mode by default. You need to install and configure a dial-up connection
on your computer, and perform it each startup.
Before setting dial-up connection parameters, verify that the HG531 V1 is correctly connected to your
computer and you have the dial-up connection account name and password provided by your Internet
service provider (ISP). This section demonstrates how to set up a Point-to-Point Protocol over Ethernet
(PPPoE) connection on Windows.
On Windows 7
1. Choose Start > Control Panel > Network and Internet > Network and Sharing Center .
2. Under Change your networking settings , click Set up a new connection or network .
3. In the Set Up a Connection or Network window, select Connect to the Internet and click Next .
4. Click Broadband (PPPoE) .
5. In User name and Password , enter the dial-up connection account name and password provided by your
ISP. In
Connectionname , name the dial-up connection. Select or deselect Allow other people to use this
connection
. Then click Connect .

8
6. Return to the Network and Sharing Center page. Click Change adapter settings . Right-click the icon for
the dial-up connection you just set up and choose
Create Shortcut from the shortcut menu. In the
displayed dialog box, click
Yes .
On Windows Vista
1. Choose Start > Control Panel > Network and Internet > Network and Sharing Center .
2. Click Set up a connection or network .
3. In the displayed window, select Connect to the Internet and click Next .
4. Click Broadband (PPPoE) .
5. In User name and Password , enter the dial-up connection account name and password provided by your
ISP. In
Connectionname , name the dial-up connection. Select or deselect Allow other people to use this
connection
. Then click Connect .
6. Return to the Network and Sharing Center page, Click Manage networkconnections . Right-click the icon
for the dial-up connection you just set up and choose
Create Shortcut from the shortcut menu. In the
displayed dialog box, click
Yes .
On Windows 8
1. Choose Settings > Control Panel > Network and Internet > Network and Sharing Center .
2. In the displayed window, click Set up a new connection or network .
3. In the displayed window, click Connect to the Internet .
4. Click Broadband (PPPoE) .
5. In User name and Password , enter the dial-up connection account name and password provided by your
ISP. In
Connectionname , name the dial-up connection. Select or deselect Allow other people to use this
connection
. Then click Connect .
6. Return to the Settings page, Click Available to see a list of available connection types.
7. Under Connections , select the connection you just set up and click Connect to open the dial-up
connection window.
8. Click Dial to connect.
On MAC OS X
1. Choose System Preferences > Network .
2. Click + to add a new network connection.
3. In the displayed dialog, select PPPoE from the Interface drop-down combo box, then select Ethernet (for
cable connection) or
Airport (for wireless connection) from the Ethernet drop-down combo box, and
enter a service name (default is PPPoE) you specified in
Service Name .

9
4. Choose the network name you set from the services list, and enter the dial-up connection account name
and password provided by your ISP in
Account Name and Password . Select or deselect Remember this
password . Then click Connect .
5. Select Show PPPoE status in menu bar .
6. Click Advanced .
7. In the displayed dialog, select settings as needed.
8. Click OK .
9. Return to the Network page, click Apply .
After you successfully set up a PPPoE connection, a dial-up connection icon is displayed on your
computer desktop.
To connect to the Internet, double-click the dial-up connection icon. In the displayed dialog box, click
Connect .

10
4 Wireless Connection Setup
Enabling and Disabling the WLAN on the HG531 V1
The following two methods are available to enable and disable the WLAN on the HG531 V1.
Using the WLAN Button
Press the WLAN button in the HG531 V1 to enable or disable the WLAN. To ascertain whether the
WLAN is enabled, view the WLAN indicator.
Using the Web Management Page
1. Log in to the web management page.
2. In the navigation tree, choose Basic > WLAN .
3. Configure wireless.
• Select Enable WLAN to enable the WLAN.
• Clear Enable WLAN to disable the WLAN.
Setting Up a Wireless Connection Using the WPS Button
Push the WPS button once to quickly set up a wireless connection between the HG531 V1 and any WPS-
capable device.
Before you set up a wireless connection using the WPS button, verify the following:
• The wireless network security mode of the HG531 V1 is WPA2-PSK or WPA-PSK/WPA2–PSK.
• The wireless device (laptop, tablet, or mobile phone) to connect to the HG531 V1 is WPS-capable.
1. Press the WPS button on the wireless device to start WPS negotiation. For details, see the user guide for
the wireless device.
2. Within 2 minutes, press and hold the WPS button (less than 3 seconds) on the HG531 V1. The WPS
indicator blinks.
When the WPS indicator on the HG531 V1 is steady on, a connection between the HG531 V1 and wireless
device is set up. The WPS indicator is on for 300 seconds, then turns off.
Manually Setting Up a Wireless Connection
The wireless configuration software provided by Windows is used as an example to describe how to set
up a wireless connection.
You can also use the tool built into the network adapter to set up a wireless connection. For details,
see the network adapter's user guide.

11
Before setting up a wireless connection, record the WLAN name and password of the HG531 V1. The
default WLAN name and password are printed on the HG531 V1 cover label.
Before setting up a wireless connection, record the WLAN name and password of the HG531 V1.
On Windows 7
1. Click in the lower right corner of your desktop.
2. From the wireless network list, select the WLAN provided by the HG531 V1. Click Connect .
3. In the displayed dialog box, enter the WLAN password and click OK .
4. In the wireless network list, check the WLAN connection status. If the status is Connected , the
computer is wirelessly connected to the HG531 V1.
On Windows Vista
1. Choose Start > Control Panel > Network and Internet > Network and Sharing Center > Manage wireless
networks
.
2. In the Connectingto a network window, double-click the WLAN provided by the HG531 V1.
3. In the displayed dialog box, enter the password and click Connect .
4. In the wireless network list, check the WLAN connection status. If the status is Connected , the
computer is wirelessly connected to the HG531 V1.
On Windows 8
1. Choose Settings from the right side of the desktop.
2. Click Available to list the available wireless networks.
3. Under Connections , select the WLAN provided by the HG531 V1 and click Connect .
4. In the displayed dialog box, enter the your WLAN password and click Next .
5. You will be asked if you would like to enable sharing between computers and connect to devices within
the network. Selecting
Yes will turn on sharing and No will leave it off.
6. In the wireless network list, check the WLAN connection status. If the status is Connected , the
computer is wirelessly connected to the HG531 V1.
On MAC OS X
1. Click at the top right side of your desktop.
2. Click Turn Airport On .
3. From the wireless network list, Select the WLAN provided by the HG531 V1.
4. In the displayed dialog box, enter your WLAN password and click Join .
5. When a check mark appears next to the HG531 V1's SSID, the computer is wireless connected to the
HG531 V1.

12
Changing Your WLAN Name and Password
WLAN access requires the WLAN name and password. To improve your WLAN security, regularly
change your WLAN name and password.
1. Log in to the web management page.
2. In the navigation tree, choose Basic > WLAN .
3. On the displayed page, enable your WLAN.
4. On the Wireless Settings area, enter your desired WLAN name and password in SSID and WPA pre-
shared key
, and click Submit .
5 Maintenance Guide
Changing the Web Management Page User Name and Password
The correct user name and password are required to log in to the web management page. Regular changes
to the web management page user name and password can effectively prevent unauthorized users from
logging in and modifying important parameters.
1. Log in to the web management page.
2. In the navigation tree, choose Maintenance > Account .
3. In New user name , enter your desired user name.
4. In Current password , enter the currently used password.
5. In New password , enter the new password you specified. In Confirm password enter the new password
again.
6. Click Submit .
When modify password successfully, this page will jump to the login page, enter the new user name
and password to log in.
If you forget the password , you can press and hold the Reset button for 6 seconds or more, then the
user name and password of the Web management page will back to factory value. This operation
will make your own configuration data lost, please perform this operation with caution.
Restoring Default Settings
Using the Reset Button
If you forget the login password to the web management page or could not access the web management
page, use the reset button on the HG531 V1 rear panel to restore the HG531 V1 to its default settings.

13
Perform this operation with caution. After the HG531 V1 is restored to its default settings, all custom
data and settings will be lost, and the password will be restored to user.
1. Press the HG531 V1 power button to power the HG531 V1 on.
2. Press and hold the reset button for 6 seconds or more.
The HG531 V1 will restart, which will cause temporary network interruptions.
Using the Configuration Tool
If the HG531 V1 parameter settings were configured incorrectly, log in to the web management page to
reload the default configuration file and restore the HG531 V1 to its default settings. Perform this
operation with caution. After the HG531 V1 is restored to its default settings, all custom data and settings
will be lost, and the password will be restored to user.
1. Log in to the web management page.
2. In the navigation tree, choose Maintenance > Device .
3. In Reset , click Restore Default Settings .
4. In the displayed dialog box, click OK .

14
6 FAQs
What Can I Do If I Cannot Open the Web Management Page?
1. Open Internet Explorer. Choose Tools > Internet Options > Connections > LAN settings , and ensure that
all check boxes are deselected.
2. Check that the computer IP address is 192.168.1.* . (* is any integer from 2 to 254.)
3. Check that the cables are securely connected to the HG531 V1 and that the LAN port's indicator is on.
4. Ensure that the user name and password are correct.
If the problem persists, restore the HG531 V1 to its default settings.
What Can I Do If the HG531 V1 Cannot Access the Internet through
a Wireless Network Adapter Sometimes or If the WLAN Connection
Is Unsteady?
This is probably because the HG531 V1 has its cables connected loosely, is placed too close to electronic
appliances with intensive interference, or is too far from the computer. Verify that:
1. The power and telephone cables are correctly connected to the HG531 V1 .
2. Your computer and the HG531 V1 are far from electric appliances that generate strong magnetic or
electric fields, such as microwave ovens, refrigerators, and cordless telephones.
3. The HG531 V1 is in an open area, and there are no obstacles, such as concrete or wooden walls, between
the
HG531 V1 and computer.
4. The HG531 V1 is close to the computer.
5. The angle between the HG531 V1 and computer is appropriate.
Do not use the HG531 V1 during thunderstorms, as the signal strength may be unsteady and the
HG531 V1 itself may be damaged due to lightning strikes.
What Can I Do If I Cannot Access the Internet?
1. Check that the Power indicator on the HG531 V1 is steady on. If the Power indicator is off, perform
further checks as follows:
a. Check that the HG531 V1 is turned on.
b. Check that electricity comes from the socket and that the power input from the socket meets the
requirements described on the label of the
HG531 V1 's power adapter. If the voltage is unstable, for example,

15
if the voltage is too high or too low, do not use the HG531 V1 . Wait until the voltage recovers, and then use the
HG531 V1 .
c. Check that the HG531 V1 is securely connected to the socket using its power adapter.
If the Power indicator is still off, contact an authorized maintenance center.
2. After powering on the HG531 V1, wait for about 3 minutes. Then check whether the ADSL indicator
turns steady on.
a. Check that the telephone line is correctly and securely connected, especially the connection between
the telephone line and the splitter.
b. Check that the HG531 V1 and telephone line are located far from any electric appliances that generate
strong magnetic or electric fields. Replace the telephone line when necessary.
If the ADSL indicator is still off, contact your network service provider.
3. Check whether the LAN indicator is on. If the LAN indicator is off, perform further checks as follows:
a. Check that the network adapter on your computer is enabled.
b. Check that the network cable between the HG531 V1 and the computer is securely connected. Remove
and then insert the network cable or replace the network cable when necessary.
If the LAN indicator is still off, contact an authorized maintenance center.
4. Check that the driver for the network adapter is correctly installed. The following example uses a
computer running the Windows XP operating system to check whether the driver for the network
adapter is installed:
a. Right-click My Computer , and choose Manage from the displayed shortcut menu.
b. In the Computer Management window, click Device Manager .
c. In the right pane of the Computer Management window, click Network adapters .
If no network adapter is found or if a question mark (?) or an exclamation mark (!) is displayed next
to the network adapter icon, the driver for the network adapter is not correctly installed. Re-install the
driver.
5. Check that PPP dial-up software is installed and parameters are set correctly. For details about
parameter settings, see the user guide for the PPP dial-up software.
6. Check that you have entered the correct user name and password required by the PPP dial-up software.
The user name and password are provided by your network service provider.
7. Check that you can use the PPP dial-up software to set up dial-up connection. If the dial-up connection
fails, perform further checks as follows:
a. Close the PPP dial-up software, and power off the HG531 V1 . After 5 minutes, power on the HG531 V1 , and
use the PPP dial-up software to dial again.
b. Restore the HG531 V1 to its default settings.
If the problem persists, contact your network service provider.

16
8. Check that the proxy server of the browser is correctly configured. The following example uses
Internet Explorer on the Windows XP operating system to check whether the proxy server of the
browser is correctly configured:
a. Launch Internet Explorer.
b. Choose Tools > Internet Options .
c. In the Internet Options dialog box, click the Connections tab.
d. In the Local Area Network (LAN) settings area, click LAN Settings .
e. In the Proxy server area of the Local Area Network (LAN) Settings dialog box, check that the Use a proxy
server for your LAN (These settings will not apply to dial-up or VPN connections).
check box is cleared.
9. Try to access more websites to check whether the HG531 V1 can access these websites. If the problem
persists, contact your network service provider.
I Often Need to Restart the HG531 V1 to Display Web Pages. What
Can I Do?
Verify the following:
1. The HG531 V1 and other devices such as telephones or fax machines are connected to the plain old
telephone service (POTS) line through a digital subscriber line (DSL) filter. For details about how to
install a DSL filter, see the description in the DSL filter manual.
2. Cables are securely connected to HG531 V1 ports. Otherwise, network stability may suffer.
3. Your computer and the HG531 V1 are far from electric appliances that generate strong magnetic or
electric fields, such as microwave ovens, refrigerators, and cordless telephones.
If the problem persists, contact your Internet Service Provider.

17
7 Appendix
Technical Specifications
Item Specifications
Power supply 12 V DC, 0.5 A
Power consumption < 5 W
Ambient operating
temperature 0°C to 40°C
Ambient humidity 5% to 95% RH (non-condensing)
Dimensions (H x W x D) 31.5 mm x 118 mm x 100 mm (1.24 in. x 4.65 in. x 3.94 in.), antenna
excluded
Weight About 360 g
DSL standard
ADSL standard
ITU G.992.1 (G.dmt)
ITU G.994.1 (G.hs)
ANSI T1.413 Issue 2
ADSL2 standard
ITU G.992.3 (G.dmt.bis) Annex A
ITU G.992.3 (G.dmt.bis) Annex L
ITU G.992.3 (G.dmt.bis) Annex M
ADSL2+ standard ITU G.992.5 (G.dmt.bitplus) Annex A
ITU G.992.5 (G.dmt.bitplus) Annex M
WLAN standard 802.11b, 802.11g, and 802.11n (2.4 GHz)
DSL transmission rate
G.dmt
T1.413
Downlink: 8 Mbit/s
Uplink: 896 kbit/s
ADSL Downlink: 12 Mbit/s
Uplink: 1024 kbit/s
ADSL2+ Downlink: 24 Mbit/s
Uplink: 1024 kbit/s
Wireless transmission rate
802.11b Up to 11 Mbit/s
802.11g Up to 54 Mbit/s
802.11n (2T2R
antenna technology) Up to 300 Mbit/s

18
Default Settings
8 For More Help
Please visit http://consumer.huawei.com/en/support/hotline for recently updated hotline and email
address in your country or region.
9 Legal Notice
Copyright © Huawei Technologies Co., Ltd. 2015. All rights reserved.
No part of this manual may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd. and its affiliates ("Huawei").
The product described in this manual may include copyrighted software of Huawei and possible licensors.
Customers shall not in any manner reproduce, distribute, modify, decompile, disassemble, decrypt,
extract, reverse engineer, lease, assign, or sublicense the said software, unless such restrictions are
prohibited by applicable laws or such actions are approved by respective copyright holders.
Parameter Default Value
LAN port IP address 192.168.1.1
LAN port subnet mask 255.255.255.0
User name to log in to the web
configuration page user
Password to log in to the web
configuration page @User1234
WLAN name (SSID) Labeled on the product cover
WLAN password (WLAN Key) Labeled on the product cover
Dynamic Host Configuration
Protocol (DHCP) server Enabled
WLAN Enabled