Hubbel KIM LIGHTING CFL User manual

P.O. Box 60080 • 16555 East Gale Ave.
City of Industry, California 91716-0080
626/968-5666 • FAX [phone]
Revised 7/16/10 ECN 100715008 Status 11 Part No. 95540
This Kim fixture is supplied with a K” NPSMmale mounting threads and locknut.
Tools Required:F” Hex Wrench Thread Sealant FlatBlade Screwdriver Phillips Screwdriver
WARNING: Fixtures must be grounded in accordance with local codes or the National Electrical Code.
Portable spear mounts using a cord and plug must be plugged into a receptacle protected by a Ground
Fault Circuit Interrupter in accordance with the National Electrical Code. Failure to do so may result in serious
personal injury.
SAFETY WARNING: To maintain light efficiency and prevent fixture overheating, lenses must be kept
clean and free of dirt, dust, leaves, trash and mineral deposits from water. For optimum performance a
regularly scheduled maintenance program should be followed. DO NOT operate luminaire with missing or
damaged lens.
SAFETY WARNING FOR QUARTZ: Fixtures can become very HOT depending on the lamp wattage used. Glass
lenses and metal areas above and around the lamp can become HOT enough to blister hands. Particular care
should be taken not to locate fixtures where small children can reach them if higher wattages are used.
CAUTION: When relamping fixture avoid touching the quartz lamp envelope with bare hands. If touching the
lamp is necessary during installation, clean the envelope with alcohol and dry with a clean, soft cloth before
burning.
NOTE: Keep the lamp free from impact while burning, as this may deform the filament and shorten the lamp
life. KEEP THIS SHEET FOR FUTURE REFERENCE.
!
1. Coat swivel threads with thread sealant to keep
moisture from entering junction box.
3. Attach fixture ground lead to cir-cuit ground.
Attach fixture leads to circuit leads observing
polarity, i.e. white-to-common and black-to-
voltage.
4. To install lamp, loosen the two (2) captive screws
on lens frame. Install lamp of type listed on
fixture label. Replace lens frame and tighten the
screws.
2. Attach fixture to junction box and orient correctly.
Tighten locknut to insure selected orientation.
CFL
Locknut
Gasket
J-Box Top
CFL- COMPACT FLOODLIGHT Installation Instructions
®
Captive Screws
Make certain electrical supply is OFF before starting fixture installation.
!
!

Page 2 Kim Lighting • 16555 E. Gale Ave. • P.O. Box 60080 • City of Industry, CA 91716-0080 • 626/968-5666 • FAX [phone]
CFL - Compact Floodlight Installation Instructions
®
KIM LIGHTING LIMITED WARRANTY
When installed in accordance with Kim Installation Instructions and
accepted trade practices, the following shall apply:
General Product Limited Warranty Coverage
All material and component parts used in the manufacture of Kim
Products, are warranted to be free from defects of material and/or
workmanship for a period of 1 year from date of sale, with the
following exceptions:
Auxiliary Equipment
All auxiliary equipment (such as lamps, ballasts, and transformers)
provided by and/or included in Kim Products shall carry the
component manufacturer's warranty.
Copper and Bronze Landscape Components
Copper and Bronze Landscape fixture components shall be
warranted against defects of material and/or workmanship, and
failure due to corrosion, for a period of 25 years from date of sale.
Composite In-Grade Components
Composite In-Grade fixture components installed below grade,
shall be warranted against defects of material and/or
workmanship, and failure due to corrosion, for a period of 7 years
from date of sale.
Aluminum Landscape Components
Aluminum Landscape fixture components not in direct contact with
soil, shall be warranted against defects of material and/or
workmanship for a period of 3 years from date of sale. Aluminum
fixture components in direct contact with soil shall be warranted
from defects of material and failure from corrosion for a period of 1
year from date of sale.
Limit of Liability and General Conditions
Only products which are installed, used and maintained in
accordance with applicable Kim instructions, specifications and
accepted trade practices, are covered by the Kim Warranty.
During the warranty period, with proof of purchase, Kim will repair
or replace with the same or similar product, at Kim's option,
without charge. Labor costs are the owner's responsibility and are
excluded from this warranty. This warranty is void if the product is
modified, tampered with, misapplied, poorly installed, improperly
maintained, or subjected to abnormal conditions.
Repair or replacement as provided under this warranty is the
exclusive remedy of the purchaser. This warranty is in lieu of all
other warranties, expressed or implied, including any implied
warranty of fitness for a particular application. Kim Lighting shall
not be liable to the purchaser for indirect or consequential
damages.
How may we serve you better?
Please let us know. Visit our website at:
www.kimlighting.com
Your concerns are important to us.
90°
*Note: Swivel stem
must be installed
with the mounting threads
facing down-to-horizontal.
Fixtures may not be
installed with mounting
threads facing upward
unless shielded from rain or
sprinklers.
*
*
5. To adjust backtilt up to maximum, loosen
swivel screw being careful not to disengage
threads. Hold fixture at desired angle and
firmly tighten swivel screw.
Swivel Screw
WARNING!
This H.I.D. / Fluorescent fixture utilizes a lamp
that may contain mercury. For information on
disposal of lamp, go to website:
www.lamprecycle.org
Maintenance: A regularly scheduled
maintenance program should be established to
retain optimum light output and reduce heat
retention. Dusting with a soft, clean, dry cloth is
normally sufficient for the reflector. Any
accumulation of dust or dirt should be removed
regularly from both sides of the lens during
relamping (using ammonia water). Do not use
alkaline or acid cleaners on reflector surfaces.