Huddly GHF10H User manual

Smart Camera
Product and Compliance
Information!
Valid for GHF10H and GHF50H!
HD-PGDE-0120-A0 !

Contents
Product variations" !4
Safety and Caution Information" !4
Temperature" !4
Modify" !4
User Instructions" !5
Installation" !5
Power" !5
Streaming" !6
Factory reset" !6
Regulatory Compliance Information" !7
European Union and UK" !7
Single Point of Contact" !7
Conformance statement European
Union EMC Directive and UK
Electromagnetic Compatibility
Regulations" !7
Canada" !9
Industry Canada statement" !9
HD-PGDE-0120-A0"2

Product variations
This document covers the following product variants!
●GHF10H!
●GHF50H!
Safety and Caution Information
Temperature
This device is intended for use in ambient temperatures
between 0 °C and 35 °C (32 °F and 95 °F). Avoid using
or storing next to heat sources, in direct sunlight, or
outside the intended temperature ranges.!
Modify
Modification to thermal solution, device components or
enclosure shall violate regulatory compliance
requirements and may induce safety hazards.!
HD-PGDE-0120-A0"4

User Instructions
The GHF10H and GHF50H cameras are made for easy
installation, using only a single RJ45 ethernet cable for
both power and communications with a host computer.!
Installation
Use the ¼” tripod mount found on the bottom face of
the camera to attach a bracket to the GHF10H or
GHF50H.!
The GHF10H and GHF50H must be installed in a
location where the top and bottom venting holes are
unobstructed, to ensure proper airflow.!
In case of wall-mounting, the GHF10H and GHF50H
should be installed less than 2 meters above floor level.!
Connect a Cat5e ethernet cable to the camera, and
terminate the cable in a PoE PSE enabled host or
midspan adapter.!
Power
The GHF10H and GHF50H cameras can be powered by
a PoE PSE which adheres to the following minimum
requirements:!
●Voltage range: 37-57V DC!
●Maximum current: 0.35A!
HD-PGDE-0120-A0"5

Streaming
The GHF10H and GHF50H support streaming over the
Real Time Streaming Protocol (RTSP).!
Factory reset
To reset the GHF10H or GHF50H to factory default, use
the following procedure:!
1. Ensure the camera is powered on!
2. Disconnect the ethernet cable from the camera!
3. Use a thin object to press the reset button
through the hole located in the top left corner of
the connector cavity!
4. Keep the button pressed while reinserting the
ethernet cable!
5. After power has been reapplied to the camera,
keep the reset button pressed for 10 seconds!
6. The camera will now reset to factory settings%
HD-PGDE-0120-A0"6

Regulatory Compliance Information
European Union and UK
Single Point of Contact!
Huddly!
Haakon VIIs gate 5!
0161 Oslo!
Norway!
Conformance statement European Union EMC
Directive and UK Electromagnetic Compatibility
Regulations
This product has been tested and found to comply with
the limits for Class A equipment according to European
Standards harmonized in the Directives, and the
relevant standards in the UK Statutory Instruments. The
limits for Class A equipment were derived for
commercial and industrial environments to provide
reasonable protection against interference with licensed
communication equipment.!
" !
HD-PGDE-0120-A0"7

Warning: This is a Class A product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take
adequate measures.!
In the European Union, this symbol indicates that this
product must not be disposed of with
household waste. It is your
responsibility to hand it over to a
designated collection point for the
recycling of waste electronic
equipment. For more information,
please contact your local waste
collection center or the point of
purchase of this product.!
HD-PGDE-0120-A0"8

Canada
Industry Canada statement!
This Class A digital apparatus complies with CAN
ICES-3 (A)/NMB-3(A).!
Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation of the
device.!
United States
FCC compliance statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.!
Note: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in
a commercial environment. This equipment "generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
HD-PGDE-0120-A0"9

manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.!
Changes or modifications to the equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.!
This product is cNus marked in accordance with the
requirements of the applicable standards for Canada
and the United States.!
!
HD-PGDE-0120-A0"10

Australia and New Zealand
This is a Class A product. In a domestic environment
this product may cause radio interference in which case
the user may be required to take adequate measures.!
!
South Korea
KCC Statement!
!
Class A device (Broadcasting Communication Device
for Office Use): This device obtained EMC registration
for office use (Class A), and may be used in places
other than home. Sellers and/or users need to take
note of this.!
HD-PGDE-0120-A0"11

Taiwan
!
!"#$%&'()*+,-
Declaration of the Presence Condition of the Restricted Substances Marking
!
HD-PGDE-0120-A0"12

./012345678!"#$%&'()*9:;<=>?@ABCDE
F68$GHIJKLMNOPQRSTKUVWUXYZ45[\]L^_
`a[\=>ZbcGHAB3dKe78fghijkl6mnKo!pqrs
tAu945QR2,STv5wx]y
I hereby ensure that “the presence conditions of the restricted substance”
provided above have been proved by testing or appropriate quality control
measures, and make sure the relevant documents provided are correct and
ready. Also, I agree to cooperate with BSMI, as the Article 49 of the
Commodity Inspection Act stipulates, to provide the relevant documents, if
needed, for verification within 28 working days when BSMI carries out the
market surveillance activities.%
HD-PGDE-0120-A0"13

Support
For more information visit:!
www.huddly.com/support!
EULA
By using this product, you agree that your use of this
product is subject to our End User Licence Agreement
terms available at:!
www.huddly.com/eula!
Privacy policy
Our privacy policy is available at: www.huddly.com/
privacy-policy!
You can find further compliance information at:
www.huddly.com/compliance
HD-PGDE-0120-A0"14
This manual suits for next models
1
Table of contents
Other Huddly IP Camera manuals
Popular IP Camera manuals by other brands

UTC Fire and Security
UTC Fire and Security TruVision Megapixel IP Camera quick start guide

ELRO
ELRO AS80CA11A installation instructions

Siqura
Siqura BL820M1IR Series quick start guide

Lorex
Lorex VANTAGE LBC6050 Series quick start guide

UAI
UAI PC-300H user manual

Channel Vision
Channel Vision 6544 instructions