Huddly L1 User manual

1
HD-PGDE-0107-A1
Valid for H3AC
Huddly L1
Product and Compliance
Information

2
Contents
Safety and Caution Information 3
Temperature 3
Modify 3
User Instructions 4
Installation 4
Power 4
Factory reset 5
Streaming 5
Regulatory Compliance Information 6
Canada 6
Industry Canada statement
United States
FCC compliance statement 6-7
Australia and New Zealand 7
European Union 8
EU Single
Point of Contact
European Union EMC
Directive conformance statement
Support 9
EULA 9
Privacy policy 9

3
Safety and Caution
Information
Temperature
is device is intended for use in ambient temperatures
between 0 °C and 35 °C (32 °F and 95 °F). Avoid using or
storing next to heat sources, in direct sunlight, or outside
the intended temperature ranges.
Modify
Modication to thermal solution, device components or
enclosure shall violate regulatory compliance requirements
and may induce safety hazards.

4
User Instructions
e L1 camera is made for easy installation, using only a single
RJ45 Ethernet cable for both power and communications
with a host computer.
Installation
Use the ¼” tripod mount found on the boom face of the
camera to aach a bracket to the L1. Using the bracket,
mount the L1 at a maximum height of 2m.
e L1 must be installed in a location where the top and
boom venting holes are unobstructed, to ensure proper
airow.
Connect minimum a Cat5e rated Ethernet cable to the camera,
and terminate the cable in a Power over Ethernet (PoE) Power
Sourcing Equipment (PSE) enabled host or midspan adapter.
If third party Ethernet cables are to be used, then prioritise
Ethernet cables with short connectors. e long connector
alternatives can be more dicult to disconnect.
Make sure to use the latest camera soware by following the
instructions at: www.huddly.com/L1/setup
Power
e L1 cameras can be powered by a PoE PSE which adheres
to the following minimum requirements:
• Voltage range: 37-57V DC
• Maximum current: 0.35A

5
Streaming
e L1 support streaming over the Real Time
Streaming Protocol (RTSP) and Open Network Video
Interface Forum (ONVIF).
Factory reset
To reset the L1 to factory default, use the following
procedure:
1. Disconnect the Ethernet cable from the camera
2. Use a thin object to press the reset buon
through the hole located in the top le corner of
the connector cavity
3. Keep the buon pressed while reinserting the
Ethernet cable
4. Aer power has been reapplied to the camera,
keep the reset buon pressed for 10 seconds
5. e camera will now reset to factory seings
Recycling
At the end of life for this product, local rules and regulations
shall be followed. is product is ment to be recycled, and if
applicable and/or possible, should be handed in to a collection
point for recycling purposes.

6
Regulatory Compliance
Information
is product is cNus marked in accordance
with the requirements of the applicable
standards for Canada and the United States.
Canada
Industry Canada statement
is Class A digital apparatus complies with CAN ICES-3
(A)/NMB-3(A).
Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device
must accept any interference, including interference that
may cause undesired operation of the device.
United States
FCC compliance statement
This device complies with Par t 1 5 o f t h e F C C R u l e s .
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.

7
is product is C-Tick marked in
accordance with the requirements of the
applicable Australian and New Zealand
standards.
is is a Class A product. In a domestic
environment this product may cause radio
interference in which case the user may
be required to take adequate measures.
Australia and New Zealand
Note: is equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. ese limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment. is
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
Changes or modications to the equipment not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment.

8
In the European Union, this symbol indicates
that this product must not be disposed of with
household waste. It is your responsibility to hand
it over to a designated collection point for the
recycling of waste electronic equip-ment. For
more information, please contact your local waste
collection center or the point of purchase of this
product.
European Union
EU Single Point of Contact
Huddly AS,
An: Compliance
Karenslyst allé 51
0279 Oslo, Norway
European Union EMC Directive conformance statement
This product has been tested and found to
comply with the limits for Class A equipment
according to European Standards harmonised in
the Directives in compliance. e limits for Class
A equipment were derived for commercial and
industrial environments to provide reasonable
protection against interference with licensed
communi-cation equipment.
Warning: is is a Class A product. In a domestic environment
this product may cause radio interference, in which case the
user may be required to take adequate measures.

9
Support
For more information visit:
www.huddly.com/support
EULA
By using this product, you agree that your use of this product is
subject to our End User Licence Agreement terms available at:
www.huddly.com/eula
Privacy policy
Our privacy policy is available at:
www.huddly.com/privacy-policy
You can nd further compliance information at:
www.huddly.com/L1/compliance