HUMA Hi-150 User manual
User Manual HUMA Hi-150
Main Functions
1. Control knob
On / Off
You can switch on the device by pressing the control button for 1 second. If the device is not in
off, the LED(2) will blink. A short press on the button keeps the device switched on for another
10 minutes and will not change the mode.
1
44
2
3
Change function
When the device is switched on, the mode can be changed by pressing the button.
Each press changes the display mode in this order:
iAQl mode => Integrated Display mode (PM2.5 / VOC / Co²) iAQI (=indoor Air Quality Index)
=>WHO mode =>PM Mode (PM2.5 / Pm10) => VOC Mode
=> Co² Mode => Temperature / Humidity Mode
2. LED Status
The Status button gives
an indication of the
current air quality
Unhealthy
Poor / Bad
Moderate
Good
Unit measurement
µg/m³
PM2.5 0 - 15 16 - 25 26 - 35 36 -<
ppm
VOC 0.000-0.220 0.221 - 0.660 0.661 - 2.200 2.201 - 10.000
Pm10 0-30 31-51 51-70 71-<
Co² Good Moderate Poor/Bad Unhealthy
(400 - 700) (701 - 1000) (1001 - 2000) (2001 - 10000)
We thank you for having chosen the HUMA HI-150.
You are now in possession of a device with which you can immediately monitor the air quality EVERYWHERE, both indoors and outdoors
to check. HUMA HI-150 measures: CO2 - VOCs - PM2 - PM1 - TEMPERATURE and HUMIDITY.
Un mode d’emploi en français peut être téléchargé sur le site www.pinewoodelectronics.com
Een nederlandstalige handleiding kan gedownload worden van www.pinewoodelectronics.com
3 Display
1. Indoor AQI mode
It shows the indoor AQI measurement with an Icon
The status LED color changes according to the iAQI level
to Blue, Green, Yellow and Red
Good iAQI Moderate iAQI Poor iAQI Unhealthy iAQI
125
iAQI iAQI
215
2. Combined View
Shown in a step-by-step chart to make air quality easier
can be assessed beyond difficult intelligible figures.
Good moderate poor unhealthy
PM2.5, VOC and Co² can be combined in one
displayed on a single screen. The show graphs
in 4 steps the air quality as good - mediocre -
poor and unhealthy.
3. WHO mode ( icon mode) (World Health Organisation)
One can easily identify the good or too high status of the fine dust level
by the 4 icons. In this case the display will automatically show the worst
of both PM2.5 and Pm10.
Blue:good
air quality
Green : moderate
air quality
Yellow : poor
air quality
Red : unhealthy
air quality
4. PM display mod (Particulate Matter) :
Simultaneous display of PM2.5 and Pm10 measured values
5. VOC display mode (Volatile Organic Compound)
VOC concentration is displayed in PPM figures
6. Co² display mode
The Co² concentration is shown in a graph
The Co² sensor applied to our product is Co²eq (Co² equivalent) which is calculated
based on the H² concentration that occurs during fasting breathing. It may react to other
harmful gases in the environment. If it shows a bad/unhealthy condition, use it as a ventilation
guideline for indoor air management.
***** In the case of CO² and VOC, the value is displayed after 15 - 60 seconds when switched on,
after which the value is updated every second.
7.Temperature / humidity mode
It displays the temperature and humidity in one screen
**** In case of temperature and humidity, the temperature/humidity sensor is located
in the housing and can give a possible deviation of 5 to 10%.
4 Battery Status : This icon shows the remaining charge of the battery
Specifications
Disclaimer
This device can be used to measure air quality in real-time portable. The OLED display has a good brightness,
but can show traces of burn-in after continuous use. It is recommended not to leave the appliance on continuously
unless absolutely necessary.
Do not expose the device to direct sunlight or excessive humidity for a long period of time.
Do not expose the device to a very dusty environment for a long period of time.
Do not disassemble the device.
Do not allow water or liquids to enter the device. This may result in a malfunction.
The device may display erroneous readings depending on the environment, misuse, wind or external factors
The measured values are purely indicative and for personal use. The manufacturer or dealer assumes no
responsibility for the correctness of the measured values.
1
2
3
4
5
6
7
Mobile
Air quality Monitor
Model # HI-150
VOC 0.000-10.000 ppm
Co² 400-10.000 ppm
VOC 0.000-10.000 ppm
PM2.5 & Pm10 0-500µg/m³
Battery Lithium -Polymeer
Charging via micro USB 5V
Operating Temperature
Storage Temperature -20°C- 60°C
Dimentions 91 x 41 x 37 mm
Nett weight 60 gr
Certificates CE,FCC, KC
Product
0°C - 40°C
www.pinewoodelectronics.com
3
info@ pinewoodelectronics.com
Imported in
Belgium by :
Ekorika bvba
Kouterdreef 45
2800 Mechelen
+32 (0)15 68.41.80
Marketing & Sales in Belgium
Pinewood Electronics Marketing N.V.
Prins Boudewijnlaan, 156
2610 Antwerpen
Tel : +32 (0)3 281.25.81
