Humanscale M/FLEX User manual

M/Connect 2
M/Power
Installation Instructions
GT-NPD-IM-4663-002-R00
© 2018 Humanscale Corporation. The text and artwork are copyrighted materials.
All rights reserved. The Humanscale mark and logo are trademarks of Humanscale
Corporation and are registered in the United States and certain other countries.
The M8.1 trademark is owned by Humanscale Corporation.
VESA Plate and Cover
Cable Routing Hook
3 mm
Hex Key
4 mm
Hex Key
5 mm
Hex Key
VESA Mount Hardware
4 Plastic Spacers
4 Standard VESA Bracket Screws
4 Extended VESA Bracket Screws
With Each VESA Plate:
M/FLEX INSTALLATION HARDWARE
C
B
A
Your monitor should move up and down easily and stay in position.
If the monitor moves down from the desired position, or is hard to lift, you should
increase the counterbalance force. If the monitor moves up from the desired position
you should decrease the counterbalance force.
1. Push the Upper Link (A) down until the Adjustment Screw (B) is visible.
2. Using the appropriate hex key (4 mm for M2.1, 5 mm for M8.1) turn the
Adjustment Screw clockwise (towards +) to increase force, or counter-clock
wise (towards –) to decrease force. Turn the Adjustment Screw (B) until the
monitor is balanced.
4. Move the monitor around to ensure that the motion is smooth and the arm
holds the monitor in place.
NOTE: When installing several of the same monitors, note the position of the needle
in the indicator (C) on top of the arm. Adjust the other arms to match.
CAUTION: Do not over-tighten the Adjustment Screw as it can damage the Arm.
Monitors Should Not Exceed:
15.5 lbs (7 Kg) for M2.1
28 lbs (12.7 Kg) for M8.1
Total Weight Not To Exceed 60 lbs (27.2 Kg)
STEP 10: WEIGHT ADJUSTMENTS
A
B
C
Your M/Flex arrives ready for use, however it may
become necessary to adjust the clamp.
1. Remove monitors and links from the Bracket.
2. Open the Lever (A) all the way.
3. Turn the Adjustment Screw (B) clockwise ¼
of a turn using the 3 mm hex key (C).
4. Test your adjustments by closing the Lever.
CAUTION: If the lever is difcult to close, or
will not close fully, it is over-tightened. Turn the
Adjustment screw counter-clockwise slightly.
Forcing it closed will damage the M/Flex.
STEP 9: M/FLEX CLAMP ADJUSTMENTS
A
1. Remove Cap from the top of the rst Post.
2. Install the Coupling Screw (A) into the top of
Post. Leave half of the Screw sticking out.
3. Screw second Post onto the Coupling Screw.
Posts must be tightly seated against each other.
4. Push Cap on top of second Post.
CAUTION: Do not install a Post, or a combination
of Posts, that exceed 24” (610 mm) in height.
STEP 8: ADDING A SECOND ROW OF MONITORS
C
B
A
1. Route power and monitor cables through
the exible Cable Clips (A) on the Upper Link.
2. Slide the Cover (B) off of the Straight Link.
3. Route cables into the Straight Link and replace
the Cover, sliding until it clicks into place.
4. Route cables through Cable Routing Hook (C).
CAUTION: Don’t insert extension cords. Don’t insert
any cord connecting one workstation to another.
STEP 7: CABLE MANAGEMENT

A
B
1. Hold the monitor at an angle and lower it onto the arm. Fit the hook at the top of
the arm into the D-shaped cutout in the VESA plate.
2. Push the bottom of the monitor back until the Quick Release Tab (B) on the arm
snaps into position.
3. To remove the monitor, lift the Quick Release Tab and pull the bottom of the
monitor away from the arm, then lift free of the hook.
NOTE: If needed, adjust the Tension Screw (A) to hold the monitor in position.
STEP 6: ATTACH MONITOR TO ARM
STEP 5: ATTACH VESA BRACKET TO MONITOR
1. Separate the VESA cover from the VESA plate.
2. Position the VESA plate over the mounting holes on the back of monitor with the
D-shaped cutouts (A) in a vertical orientation. Attach using provided VESA screws.
3. Snap the VESA cover back in place.
The VESA plate features 75 mm and 100 mm hole patterns.
You may also use the screws which came with your monitor to attach the VESA plate.
If you must offset the plate from the monitor, use the plastic spacers and extended
screws provided.
A
A
Before adding each link, adjust the Smart Stop according to Step 3.
1. Insert the rst link into the mount until the
release button (A) locks in place.
2. Insert the next link into the rst link.
3. To remove a link, press the release button
and lift upward near the joint.
NOTE: Triple link congurations
are not supported.
NOTE: The installation order of the
links must not allow the monitor to
pass behind the rear edge of the unit.
STEP 4: ATTACH ARMS TO BRACKET
Arm can rotate
without stopping
Arm can rotate 180˚
Arm can rotate 90˚
A Smart Stop Ring is included at every Quick Attach joint.
Position the Smart Stop Ring to limit the arm’s range of motion.
The marked angle will be in the center of the range of motion.
NOTE: The stop rings must be congured in such a way that
does not allow the monitor to pass behind the rear edge of
the unit.
STEP 3: SMART STOP ADJUSTMENT
CABLE ROUTING HOOK
1. Spread the hooks around the post in the desired location.
2. Squeeze the two sides until the Lock (K) snaps together.
3. To release, use ngernail to disengage the Lock.
TRIPLE MONITOR APPLICATIONS
1. Remove the two set screws (E) that retain the Bracket Cap (F). Lift the Bracket Cap (F)
upwards to remove it.
.
2. Install the Extension Bracket (G) on top of the Dual Bracket. Insert the Tabs (H) into
the Pockets (J). Replace the Set Screws. Tighten screws until the Extension Bracket is
secure and the screws are ush with the surface.
3. Insert the Bracket Cap into the top of the Extension Bracket. Push down until it clicks
into place.
SINGLE AND DUAL MONITOR APPLICATIONS
1. With the Lever (A) open, position the Dual Bracket (B) at the desired height on
the Post (C).
2. Close the Lever entirely.
3. If you are using a second monitor, lift and remove the Cover (D).
BA
C
STEP 2: BRACKET ASSEMBLY AND CABLE CLIP
K
D
G
F
H
J
E
F
Before you install your new M/Flex and monitor arms you will need to set
up your M/Connect 2 or M/Power base.
Before proceeding, please refer to the installation manual that came with
your M/Connect 2 or M/Power for instructions on mounting the base to
your work surface.
STEP 1: ATTACH MOUNT TO WORK SURFACE

A
B
1. Hold the monitor at an angle and lower it onto the arm. Fit the hook at the top of
the arm into the D-shaped cutout in the VESA plate.
2. Push the bottom of the monitor back until the Quick Release Tab (B) on the arm
snaps into position.
3. To remove the monitor, lift the Quick Release Tab and pull the bottom of the
monitor away from the arm, then lift free of the hook.
NOTE: If needed, adjust the Tension Screw (A) to hold the monitor in position.
STEP 6: ATTACH MONITOR TO ARM
STEP 5: ATTACH VESA BRACKET TO MONITOR
1. Separate the VESA cover from the VESA plate.
2. Position the VESA plate over the mounting holes on the back of monitor with the
D-shaped cutouts (A) in a vertical orientation. Attach using provided VESA screws.
3. Snap the VESA cover back in place.
The VESA plate features 75 mm and 100 mm hole patterns.
You may also use the screws which came with your monitor to attach the VESA plate.
If you must offset the plate from the monitor, use the plastic spacers and extended
screws provided.
A
A
Before adding each link, adjust the Smart Stop according to Step 3.
1. Insert the rst link into the mount until the
release button (A) locks in place.
2. Insert the next link into the rst link.
3. To remove a link, press the release button
and lift upward near the joint.
NOTE: Triple link congurations
are not supported.
NOTE: The installation order of the
links must not allow the monitor to
pass behind the rear edge of the unit.
STEP 4: ATTACH ARMS TO BRACKET
Arm can rotate
without stopping
Arm can rotate 180˚
Arm can rotate 90˚
A Smart Stop Ring is included at every Quick Attach joint.
Position the Smart Stop Ring to limit the arm’s range of motion.
The marked angle will be in the center of the range of motion.
NOTE: The stop rings must be congured in such a way that
does not allow the monitor to pass behind the rear edge of
the unit.
STEP 3: SMART STOP ADJUSTMENT
CABLE ROUTING HOOK
1. Spread the hooks around the post in the desired location.
2. Squeeze the two sides until the Lock (K) snaps together.
3. To release, use ngernail to disengage the Lock.
TRIPLE MONITOR APPLICATIONS
1. Remove the two set screws (E) that retain the Bracket Cap (F). Lift the Bracket Cap (F)
upwards to remove it.
.
2. Install the Extension Bracket (G) on top of the Dual Bracket. Insert the Tabs (H) into
the Pockets (J). Replace the Set Screws. Tighten screws until the Extension Bracket is
secure and the screws are ush with the surface.
3. Insert the Bracket Cap into the top of the Extension Bracket. Push down until it clicks
into place.
SINGLE AND DUAL MONITOR APPLICATIONS
1. With the Lever (A) open, position the Dual Bracket (B) at the desired height on
the Post (C).
2. Close the Lever entirely.
3. If you are using a second monitor, lift and remove the Cover (D).
BA
C
STEP 2: BRACKET ASSEMBLY AND CABLE CLIP
K
D
G
F
H
J
E
F
Before you install your new M/Flex and monitor arms you will need to set
up your M/Connect 2 or M/Power base.
Before proceeding, please refer to the installation manual that came with
your M/Connect 2 or M/Power for instructions on mounting the base to
your work surface.
STEP 1: ATTACH MOUNT TO WORK SURFACE

A
B
1. Hold the monitor at an angle and lower it onto the arm. Fit the hook at the top of
the arm into the D-shaped cutout in the VESA plate.
2. Push the bottom of the monitor back until the Quick Release Tab (B) on the arm
snaps into position.
3. To remove the monitor, lift the Quick Release Tab and pull the bottom of the
monitor away from the arm, then lift free of the hook.
NOTE: If needed, adjust the Tension Screw (A) to hold the monitor in position.
STEP 6: ATTACH MONITOR TO ARM
STEP 5: ATTACH VESA BRACKET TO MONITOR
1. Separate the VESA cover from the VESA plate.
2. Position the VESA plate over the mounting holes on the back of monitor with the
D-shaped cutouts (A) in a vertical orientation. Attach using provided VESA screws.
3. Snap the VESA cover back in place.
The VESA plate features 75 mm and 100 mm hole patterns.
You may also use the screws which came with your monitor to attach the VESA plate.
If you must offset the plate from the monitor, use the plastic spacers and extended
screws provided.
A
A
Before adding each link, adjust the Smart Stop according to Step 3.
1. Insert the rst link into the mount until the
release button (A) locks in place.
2. Insert the next link into the rst link.
3. To remove a link, press the release button
and lift upward near the joint.
NOTE: Triple link congurations
are not supported.
NOTE: The installation order of the
links must not allow the monitor to
pass behind the rear edge of the unit.
STEP 4: ATTACH ARMS TO BRACKET
Arm can rotate
without stopping
Arm can rotate 180˚
Arm can rotate 90˚
A Smart Stop Ring is included at every Quick Attach joint.
Position the Smart Stop Ring to limit the arm’s range of motion.
The marked angle will be in the center of the range of motion.
NOTE: The stop rings must be congured in such a way that
does not allow the monitor to pass behind the rear edge of
the unit.
STEP 3: SMART STOP ADJUSTMENT
CABLE ROUTING HOOK
1. Spread the hooks around the post in the desired location.
2. Squeeze the two sides until the Lock (K) snaps together.
3. To release, use ngernail to disengage the Lock.
TRIPLE MONITOR APPLICATIONS
1. Remove the two set screws (E) that retain the Bracket Cap (F). Lift the Bracket Cap (F)
upwards to remove it.
.
2. Install the Extension Bracket (G) on top of the Dual Bracket. Insert the Tabs (H) into
the Pockets (J). Replace the Set Screws. Tighten screws until the Extension Bracket is
secure and the screws are ush with the surface.
3. Insert the Bracket Cap into the top of the Extension Bracket. Push down until it clicks
into place.
SINGLE AND DUAL MONITOR APPLICATIONS
1. With the Lever (A) open, position the Dual Bracket (B) at the desired height on
the Post (C).
2. Close the Lever entirely.
3. If you are using a second monitor, lift and remove the Cover (D).
BA
C
STEP 2: BRACKET ASSEMBLY AND CABLE CLIP
K
D
G
F
H
J
E
F
Before you install your new M/Flex and monitor arms you will need to set
up your M/Connect 2 or M/Power base.
Before proceeding, please refer to the installation manual that came with
your M/Connect 2 or M/Power for instructions on mounting the base to
your work surface.
STEP 1: ATTACH MOUNT TO WORK SURFACE

A
B
1. Hold the monitor at an angle and lower it onto the arm. Fit the hook at the top of
the arm into the D-shaped cutout in the VESA plate.
2. Push the bottom of the monitor back until the Quick Release Tab (B) on the arm
snaps into position.
3. To remove the monitor, lift the Quick Release Tab and pull the bottom of the
monitor away from the arm, then lift free of the hook.
NOTE: If needed, adjust the Tension Screw (A) to hold the monitor in position.
STEP 6: ATTACH MONITOR TO ARM
STEP 5: ATTACH VESA BRACKET TO MONITOR
1. Separate the VESA cover from the VESA plate.
2. Position the VESA plate over the mounting holes on the back of monitor with the
D-shaped cutouts (A) in a vertical orientation. Attach using provided VESA screws.
3. Snap the VESA cover back in place.
The VESA plate features 75 mm and 100 mm hole patterns.
You may also use the screws which came with your monitor to attach the VESA plate.
If you must offset the plate from the monitor, use the plastic spacers and extended
screws provided.
A
A
Before adding each link, adjust the Smart Stop according to Step 3.
1. Insert the rst link into the mount until the
release button (A) locks in place.
2. Insert the next link into the rst link.
3. To remove a link, press the release button
and lift upward near the joint.
NOTE: Triple link congurations
are not supported.
NOTE: The installation order of the
links must not allow the monitor to
pass behind the rear edge of the unit.
STEP 4: ATTACH ARMS TO BRACKET
Arm can rotate
without stopping
Arm can rotate 180˚
Arm can rotate 90˚
A Smart Stop Ring is included at every Quick Attach joint.
Position the Smart Stop Ring to limit the arm’s range of motion.
The marked angle will be in the center of the range of motion.
NOTE: The stop rings must be congured in such a way that
does not allow the monitor to pass behind the rear edge of
the unit.
STEP 3: SMART STOP ADJUSTMENT
CABLE ROUTING HOOK
1. Spread the hooks around the post in the desired location.
2. Squeeze the two sides until the Lock (K) snaps together.
3. To release, use ngernail to disengage the Lock.
TRIPLE MONITOR APPLICATIONS
1. Remove the two set screws (E) that retain the Bracket Cap (F). Lift the Bracket Cap (F)
upwards to remove it.
.
2. Install the Extension Bracket (G) on top of the Dual Bracket. Insert the Tabs (H) into
the Pockets (J). Replace the Set Screws. Tighten screws until the Extension Bracket is
secure and the screws are ush with the surface.
3. Insert the Bracket Cap into the top of the Extension Bracket. Push down until it clicks
into place.
SINGLE AND DUAL MONITOR APPLICATIONS
1. With the Lever (A) open, position the Dual Bracket (B) at the desired height on
the Post (C).
2. Close the Lever entirely.
3. If you are using a second monitor, lift and remove the Cover (D).
BA
C
STEP 2: BRACKET ASSEMBLY AND CABLE CLIP
K
D
G
F
H
J
E
F
Before you install your new M/Flex and monitor arms you will need to set
up your M/Connect 2 or M/Power base.
Before proceeding, please refer to the installation manual that came with
your M/Connect 2 or M/Power for instructions on mounting the base to
your work surface.
STEP 1: ATTACH MOUNT TO WORK SURFACE

M/Connect 2
M/Power
Installation Instructions
GT-NPD-IM-4663-002-R00
© 2018 Humanscale Corporation. The text and artwork are copyrighted materials.
All rights reserved. The Humanscale mark and logo are trademarks of Humanscale
Corporation and are registered in the United States and certain other countries.
The M8.1 trademark is owned by Humanscale Corporation.
VESA Plate and Cover
Cable Routing Hook
3 mm
Hex Key
4 mm
Hex Key
5 mm
Hex Key
VESA Mount Hardware
4 Plastic Spacers
4 Standard VESA Bracket Screws
4 Extended VESA Bracket Screws
With Each VESA Plate:
M/FLEX INSTALLATION HARDWARE
C
B
A
Your monitor should move up and down easily and stay in position.
If the monitor moves down from the desired position, or is hard to lift, you should
increase the counterbalance force. If the monitor moves up from the desired position
you should decrease the counterbalance force.
1. Push the Upper Link (A) down until the Adjustment Screw (B) is visible.
2. Using the appropriate hex key (4 mm for M2.1, 5 mm for M8.1) turn the
Adjustment Screw clockwise (towards +) to increase force, or counter-clock
wise (towards –) to decrease force. Turn the Adjustment Screw (B) until the
monitor is balanced.
4. Move the monitor around to ensure that the motion is smooth and the arm
holds the monitor in place.
NOTE: When installing several of the same monitors, note the position of the needle
in the indicator (C) on top of the arm. Adjust the other arms to match.
CAUTION: Do not over-tighten the Adjustment Screw as it can damage the Arm.
Monitors Should Not Exceed:
15.5 lbs (7 Kg) for M2.1
28 lbs (12.7 Kg) for M8.1
Total Weight Not To Exceed 60 lbs (27.2 Kg)
STEP 10: WEIGHT ADJUSTMENTS
A
B
C
Your M/Flex arrives ready for use, however it may
become necessary to adjust the clamp.
1. Remove monitors and links from the Bracket.
2. Open the Lever (A) all the way.
3. Turn the Adjustment Screw (B) clockwise ¼
of a turn using the 3 mm hex key (C).
4. Test your adjustments by closing the Lever.
CAUTION: If the lever is difcult to close, or
will not close fully, it is over-tightened. Turn the
Adjustment screw counter-clockwise slightly.
Forcing it closed will damage the M/Flex.
STEP 9: M/FLEX CLAMP ADJUSTMENTS
A
1. Remove Cap from the top of the rst Post.
2. Install the Coupling Screw (A) into the top of
Post. Leave half of the Screw sticking out.
3. Screw second Post onto the Coupling Screw.
Posts must be tightly seated against each other.
4. Push Cap on top of second Post.
CAUTION: Do not install a Post, or a combination
of Posts, that exceed 24” (610 mm) in height.
STEP 8: ADDING A SECOND ROW OF MONITORS
C
B
A
1. Route power and monitor cables through
the exible Cable Clips (A) on the Upper Link.
2. Slide the Cover (B) off of the Straight Link.
3. Route cables into the Straight Link and replace
the Cover, sliding until it clicks into place.
4. Route cables through Cable Routing Hook (C).
CAUTION: Don’t insert extension cords. Don’t insert
any cord connecting one workstation to another.
STEP 7: CABLE MANAGEMENT

M/Connect 2
M/Power
Installation Instructions
GT-NPD-IM-4663-002-R00
© 2018 Humanscale Corporation. The text and artwork are copyrighted materials.
All rights reserved. The Humanscale mark and logo are trademarks of Humanscale
Corporation and are registered in the United States and certain other countries.
The M8.1 trademark is owned by Humanscale Corporation.
VESA Plate and Cover
Cable Routing Hook
3 mm
Hex Key
4 mm
Hex Key
5 mm
Hex Key
VESA Mount Hardware
4 Plastic Spacers
4 Standard VESA Bracket Screws
4 Extended VESA Bracket Screws
With Each VESA Plate:
M/FLEX INSTALLATION HARDWARE
C
B
A
Your monitor should move up and down easily and stay in position.
If the monitor moves down from the desired position, or is hard to lift, you should
increase the counterbalance force. If the monitor moves up from the desired position
you should decrease the counterbalance force.
1. Push the Upper Link (A) down until the Adjustment Screw (B) is visible.
2. Using the appropriate hex key (4 mm for M2.1, 5 mm for M8.1) turn the
Adjustment Screw clockwise (towards +) to increase force, or counter-clock
wise (towards –) to decrease force. Turn the Adjustment Screw (B) until the
monitor is balanced.
4. Move the monitor around to ensure that the motion is smooth and the arm
holds the monitor in place.
NOTE: When installing several of the same monitors, note the position of the needle
in the indicator (C) on top of the arm. Adjust the other arms to match.
CAUTION: Do not over-tighten the Adjustment Screw as it can damage the Arm.
Monitors Should Not Exceed:
15.5 lbs (7 Kg) for M2.1
28 lbs (12.7 Kg) for M8.1
Total Weight Not To Exceed 60 lbs (27.2 Kg)
STEP 10: WEIGHT ADJUSTMENTS
A
B
C
Your M/Flex arrives ready for use, however it may
become necessary to adjust the clamp.
1. Remove monitors and links from the Bracket.
2. Open the Lever (A) all the way.
3. Turn the Adjustment Screw (B) clockwise ¼
of a turn using the 3 mm hex key (C).
4. Test your adjustments by closing the Lever.
CAUTION: If the lever is difcult to close, or
will not close fully, it is over-tightened. Turn the
Adjustment screw counter-clockwise slightly.
Forcing it closed will damage the M/Flex.
STEP 9: M/FLEX CLAMP ADJUSTMENTS
A
1. Remove Cap from the top of the rst Post.
2. Install the Coupling Screw (A) into the top of
Post. Leave half of the Screw sticking out.
3. Screw second Post onto the Coupling Screw.
Posts must be tightly seated against each other.
4. Push Cap on top of second Post.
CAUTION: Do not install a Post, or a combination
of Posts, that exceed 24” (610 mm) in height.
STEP 8: ADDING A SECOND ROW OF MONITORS
C
B
A
1. Route power and monitor cables through
the exible Cable Clips (A) on the Upper Link.
2. Slide the Cover (B) off of the Straight Link.
3. Route cables into the Straight Link and replace
the Cover, sliding until it clicks into place.
4. Route cables through Cable Routing Hook (C).
CAUTION: Don’t insert extension cords. Don’t insert
any cord connecting one workstation to another.
STEP 7: CABLE MANAGEMENT

M/Connect 2
M/Power
Installation Instructions
GT-NPD-IM-4663-002-R00
© 2018 Humanscale Corporation. The text and artwork are copyrighted materials.
All rights reserved. The Humanscale mark and logo are trademarks of Humanscale
Corporation and are registered in the United States and certain other countries.
The M8.1 trademark is owned by Humanscale Corporation.
VESA Plate and Cover
Cable Routing Hook
3 mm
Hex Key
4 mm
Hex Key
5 mm
Hex Key
VESA Mount Hardware
4 Plastic Spacers
4 Standard VESA Bracket Screws
4 Extended VESA Bracket Screws
With Each VESA Plate:
M/FLEX INSTALLATION HARDWARE
C
B
A
Your monitor should move up and down easily and stay in position.
If the monitor moves down from the desired position, or is hard to lift, you should
increase the counterbalance force. If the monitor moves up from the desired position
you should decrease the counterbalance force.
1. Push the Upper Link (A) down until the Adjustment Screw (B) is visible.
2. Using the appropriate hex key (4 mm for M2.1, 5 mm for M8.1) turn the
Adjustment Screw clockwise (towards +) to increase force, or counter-clock
wise (towards –) to decrease force. Turn the Adjustment Screw (B) until the
monitor is balanced.
4. Move the monitor around to ensure that the motion is smooth and the arm
holds the monitor in place.
NOTE: When installing several of the same monitors, note the position of the needle
in the indicator (C) on top of the arm. Adjust the other arms to match.
CAUTION: Do not over-tighten the Adjustment Screw as it can damage the Arm.
Monitors Should Not Exceed:
15.5 lbs (7 Kg) for M2.1
28 lbs (12.7 Kg) for M8.1
Total Weight Not To Exceed 60 lbs (27.2 Kg)
STEP 10: WEIGHT ADJUSTMENTS
A
B
C
Your M/Flex arrives ready for use, however it may
become necessary to adjust the clamp.
1. Remove monitors and links from the Bracket.
2. Open the Lever (A) all the way.
3. Turn the Adjustment Screw (B) clockwise ¼
of a turn using the 3 mm hex key (C).
4. Test your adjustments by closing the Lever.
CAUTION: If the lever is difcult to close, or
will not close fully, it is over-tightened. Turn the
Adjustment screw counter-clockwise slightly.
Forcing it closed will damage the M/Flex.
STEP 9: M/FLEX CLAMP ADJUSTMENTS
A
1. Remove Cap from the top of the rst Post.
2. Install the Coupling Screw (A) into the top of
Post. Leave half of the Screw sticking out.
3. Screw second Post onto the Coupling Screw.
Posts must be tightly seated against each other.
4. Push Cap on top of second Post.
CAUTION: Do not install a Post, or a combination
of Posts, that exceed 24” (610 mm) in height.
STEP 8: ADDING A SECOND ROW OF MONITORS
C
B
A
1. Route power and monitor cables through
the exible Cable Clips (A) on the Upper Link.
2. Slide the Cover (B) off of the Straight Link.
3. Route cables into the Straight Link and replace
the Cover, sliding until it clicks into place.
4. Route cables through Cable Routing Hook (C).
CAUTION: Don’t insert extension cords. Don’t insert
any cord connecting one workstation to another.
STEP 7: CABLE MANAGEMENT