Hunt HTP-T800 User manual
HTP‐T800
H.264VIDEOSERVER
UserManualVer.1.0
HTP-T800 User Manual
-1-
Safety Precaution
Make sure to turn off the power before installing HTP-T800.
Do not install under the direct sunlight or in dusty areas.
Make sure to use the product within the temperature and humidity specified in the specification.
Do not operate the product in presence of vibrations or strong magnetic fields.
Do not put electrically conducting materials in the ventilation hole.
Do not open the top cover of the product. It may cause a failure or electric shock on the
components.
To prevent from overheating, make sure to keep the distance at least 10cm from the ventilation
hole.
Check for proper voltage before connecting the power.
We appreciate your purchasing HTP-T800.
Before installing the product, please read the following with care.
HTP-T800 User Manual
-2-
Table of Content
Table of Content ................................................................................................................................... 2
1. Introduction ...................................................................................................................................... 4
1. About User Manual.................................................................................................................... 4
2. Feature...................................................................................................................................... 4
3. Product and Accessories ........................................................................................................... 6
4. Part Names and Description...................................................................................................... 7
5. System Modes and Connections............................................................................................... 8
2. Installation ...................................................................................................................................... 12
1. Connecting Video .................................................................................................................... 12
2. Connecting Audio .................................................................................................................... 12
3. Connecting Serial Ports........................................................................................................... 12
4. Connecting Sensor and Alarm................................................................................................. 12
5. Connecting Power ................................................................................................................... 12
6. Checking Operating................................................................................................................. 13
3. System Operation........................................................................................................................... 14
1. LED Display ............................................................................................................................ 14
2. Remote Video Monitoring ........................................................................................................ 14
3. Initialization of IP Address ....................................................................................................... 16
4. Remote Configuration..................................................................................................................... 18
1. Remote Configuration ............................................................................................................. 18
2. Encoder Configuration............................................................................................................. 18
2.1 System Configuration ..................................................................................................... 19
2.2 Video Configuration........................................................................................................ 21
2.3 Audio Configuration........................................................................................................ 25
2.4 Network Configuration.................................................................................................... 26
2.5 Serial Port Configuration ................................................................................................ 29
2.6 Event Configuration........................................................................................................ 32
2.7 Preset Configuration....................................................................................................... 35
2.8 User Configuration ......................................................................................................... 36
3. Decoder System...................................................................................................................... 39
3.1 Video Configuration........................................................................................................ 40
3.2 Network Configuration.................................................................................................... 41
3.3 Event Configuration........................................................................................................ 43
5. True Manager ................................................................................................................................. 45
1. True Manager Software........................................................................................................... 45
2. Server Registration and Removal............................................................................................ 45
HTP-T800 User Manual
-3-
3. Server Connection Management............................................................................................. 48
4. Server Status Monitoring ......................................................................................................... 48
5. Network and System Diagnostics ............................................................................................ 49
6. F/W Upgrade........................................................................................................................... 52
7. Remove Configuration and Video Monitoring .......................................................................... 53
6. Trouble Shooting ............................................................................................................................ 53
Appendix A: Sensor and Alarm Port ................................................................................................... 54
1. Sensor Port ............................................................................................................................. 54
2. Alarm Port ............................................................................................................................... 54
Appendix B: Serial Port ...................................................................................................................... 55
1. RS-232 Port ............................................................................................................................ 55
2. RS-422/485 Port...................................................................................................................... 55
3. PoE Specification .................................................................................................................... 56
HTP-T800 User Manual
-4-
1. Introduction
1. About User Manual
The User Manual is provided information on operation of the high quality video surveillance system,
This manual includes how to trouble shoot in case of problems as well as installation, operation and
setting up the HTP-T800
2. Feature
HTP-T800 is a video and audio surveillance transmission system based on IP network through LAN,
ADSL/VDSL, and Wireless LAN. The HTP-T800 series operates as one of the two modes: Encoder,
Decoder. Encoder system compresses and transmits video data. Decoder receives and
decompresses the video data.
Video
-High-quality compression algorithm, H.264 & MJPEG support
-Compression in various resolution: CIF, Half-D1 and D1
-Wide range of video transmission rate: 32kbps ~ 8Mbps
-Various transmission mode: CBR and VBR
-Motion Detection
Audio
-Multi-transmission mode: Uni-direction (Encoder -> Decoder, Decoder -> Encoder), Bi-
direction
Network
-Fixed IP & Dynamic IP(DHCP) support
-1:1, 1:N support
-Multicasting
-Automatic transmit rate control according to network condition
Serial Data
-Two serial ports
-Various PTZ camera protocol
-Data pass-through mode: Serial data communication between Encoder – Decoder
HTP-T800 User Manual
-5-
Sensor and Alarm
-Support direct connections of external sensor and alarm devices.
-Event Alarm
USB
-Connection to internal or external USB storage for remote access
User Interface
-System status display utilizing OSD(On Screen Display)
-Diagnose and upgrade through dedicated program called True Manager
-System configuration using Internet Explorer
High Reliability
-Reliable embedded system
-System recovery utilizing dual watch-dog functions
HTP-T800 User Manual
-6-
3. Product and Accessories
HTP-T800 System Quick Manual
Power adaptor and cable User Manual & S/W CD
Screws Brackets
<Picture 1> Product and Accessories
HTP-T800 User Manual
-7-
4. Part Names and Description
Front View
Parts Function
nLEDs Display power On/Off condition, Link, Status and data
oAudio In, Out Audio Input and Output
pHDMI Output HDMI Output
qUSB USB port for any USB device
rLAN(Ethernet) 100/10-base-T Ethernet interface
sReset button Initialization of network setting
s
p q
o
r
n
HTP-T800 User Manual
-8-
Rear View
Te r m i n al Function
nPOWER IN DC 12V power input
oSENSOR Sensor input
pALARM Relay output
qRS-422/485
(COM2)
Serial port 2 (COM2) for PTZ control and etc. Support RS-422 and
RS-485 protocol
rVIDEO OUT Video output
sVIDEO IN Video input
tAUDIO OUT Audio output
uAUDIO IN Audio input
vRESET Reset button for network reset
5. System Modes and Connections
The HTP-T800 system operates in one of two modes: Encoder, Decoder. HTP-T800 systems can be
connected in either 1-to-1 fashion where one encoder is connected one decoder or 1-to-many fashion
where one encoder connected to many decoders.
r t
o p q s
n
HTP-T800 User Manual
-9-
Following chart shows possible combinations of video, audio and serial data transmission.
System Mode Video Audio Serial Data
Encoder Transmit Transmission/Receive Transmit/Receive
Decoder Receive Transmission /Receive Transmit/Receive
Therefore, the system modes are defined by the video communication and all system modes are
capable of bi-directional transmission of audio or serial data.
Topology
Generally, the encoder and the decoder are connected in 1-to-1 mode. To support specific situations,
1-to-many connection is also supported.
1:1 Connection (Unidirection)
Mostly used configuration is 1 to 1 connection. An encoder is installed at a site where video images
can be transmitted and a decoder is installed at a center location to receive and view the video
images on analog monitor. Audio and serial data are transferred in either direction.
1:N Connection (Unidirection)
Encoder Decoder
Site Remote Center
HTP-T800 User Manual
-10-
In this configuration, a site can be monitored from many remote center locations. Although up to 64
decoders can be connected to on encoder, in the real network environment, network bandwidth can
limit the maximum connections.
Functionally, the CMS (Central Monitoring System) software can replace the decoder.
Multicast Mode
In 1:N Connection, network that supports multicasting, a large number of decoders can receive video
efficiently from an encoder transmit a single streaming of video and audio.
Relaying
In this arrangement, video and audio can be retransmitted from a center to another center. The
arrangement is useful when the network bandwidth to the site is limited while there are more than one
center wanting to monitor the site.
CMS (Central Monitoring System)
Encoder Decoder
Site Center 1
Decoder
Center 2
Encoder Decoder
Decoder
Decoder
Remote Center
Site
HTP-T800 User Manual
-11-
CMS (Central Monitoring System) is a Windows based remote monitoring program to access multiple
encoders for real-time monitoring or control of the encoders and connected cameras. Please refer to
CMS User Manual for more information on CMS.
Encoder Decoder
Site Remote Center
Encoder CMS
CMS
Site Remote Center
HTP-T800 User Manual
-12-
2. Installation
1. Connecting Video
Encoder System
-Connect camera video output line to the encoder (HTP-T800) video input port.
Decoder System
-Connect monitor video input line to the decoder (HTP-T800) video output port.
2. Connecting Audio
Audio is bi-directional in any configuration regardless of the system mode. If necessary, it can be
configured to be in transmit-only, receive -only or bi-directional mode.
- Connect audio input and output ports to audio devices accordingly.
- Audio signal is in line level, therefore, microphone or speaker with amplification function should
be used.
3. Connecting Serial Ports
For camera control, PTZ controller (keyboard) and receiver can be connected to serial ports. Two
corresponding serial ports in encoder and decoder which are connected in connected in 1-to-1 fashion
works in pass-through mode. This means that commands at a local system’s COM1 port will be
transparently passed to the remote system’s COM1 port. Also, a command at a local system COM2
port will pass to the remote system’s COM2 port.
4. Connecting Sensor and Alarm
Connect sensor and alarm devices to corresponding terminals accordingly.
5. Connecting Power
After confirming the power source, connect power adaptor and connect the 12VDC connector to the
system.
HTP-T800 User Manual
-13-
6. Checking Operating
Once the power is supplied to the camera, it will start booting. The system will boot up to an operating
mode after approximately 40-60 seconds. The green LED on the Ethernet port will flash indicating the
system is ready.
Software provided on the disc called True Manager allows you to check the IP address and other
network details of the camera. Please refer to the True Manager manual for instructions on how to find
the IP address of the camera and if required changing it.
Encoder LED Display
Above LED status display shows that neither camera is connected nor a decoder is connected. Once
the encoder is connected to a decoder, color of link LED will light in green color and the LED will blink
as video or audio transmissions occur.
Decoder LED Display
Above LED status display shows that the encoder has started without connecting to an encoder. Once
an encoder is connected, the color of link LED will be changed to green and the LED will blink as
video or audio data transmissions occur.
PWR STATUS LINK
Red Green
Blinking
DATA
OFF
PWR STATUS LINK DATA
OFF
Red Green
Blinking
OFF
Red
Blinking
HTP-T800 User Manual
-14-
3. System Operation
1. LED Display
Description of LEDs
System status can be monitored with LEDs.
LED State Description
Off No power
PWR Red Power on
Green blinking Normally operating
Red System failure: Needs diagnostics
Constant change of colors
between Red and Green
NTSC/PAL setting does not match with input
video signal
Red Blinking Failed to obtain IP address in DHCP mode
Constant change of colors
between Green blinking 2
times and Red blinking
once
Failed to register on DDNS server
Green blinking, Red blinks
once every 5 seconds
Video loss in Encoder system
STATUS
Orange blinking Improper resolution setting in duplex mode
Off No connection to remote system
Green Connected to a remote system
Red blinking Decoder only: trying to connect to an Encoder
LINK
Orange Illegal connection (unsupported combination of
system modes)
Green Data transmission in progress
Red Data loss
DATA
Off No data transmission
2. Remote Video Monitoring
There are two ways to view the remote video when the connections are completed between a site and
center system. In order for a proper operation, an IP address must be set accordingly. Please refer to
True Manager or Remote Setting in Chapter 4 and 5 for further details.
Video Monitoring with Decoder System
Once the encoder IP address is set in the remote IP address section of the decoder, the decoder
system will connect to the encoder system and start receiving the video images. Normally, a monitor
connected to the decoder will display video images.
HTP-T800 User Manual
-15-
Video Monitoring using Internet Explorer
If HTP-T800’s IP address in entered on the Internet Explorer, the system will ask for confirmation to
install Active-X control. Once authorized, the Internet Explorer will start to display video images from
the encoder as shown below.
Video Selection
If Primary is selected, Max. 720 x 480 (NTSC) or 704 x 756 (PAL) via H.264 compression
algorithm video can be displayed. And once activated Dual Video compression and Secondary
may be selected, H.264 or MJPEG compression algorithm video can be displayed in this case.
.
Screen Size:
Adjustable Screen Size
Digital Zoom:
Max 5x Digital Zoom is available.
http://192.168.10.100
HTP-T800 User Manual
-16-
Focus Near, Focus Far, Auto Focus
Adjust the focus
Sensor Input
When the sensor on the HTP-T800 is connected and working, the light turns red.
Alarm Output
Alarm Output button can trigger an event directly from the Live View page.
Snapshot
Snapshot button saves a snapshot of the video image currently on display. Captured picture
can be stored as BMP or a JPEG file.
Tal k
Transfer audio to audio device connected HTP-T800.
3. Initialization of IP Address
If a system IP address is lost, the system can be reset to a known IP address using the reset button in
the back side of the system:
cWhile system is in operation, press the reset button more than 5 seconds.
dThe system will reboot automatically
eOnce the system has been rebooted, IP address will be set to the following.
-IP mode: Fixed IP
-IP address: 192.168.10.100
-Subnet mask: 255.255.255.0
-Gateway : 192.168.10.1
-Base port : 2222
HTP-T800 User Manual
-17-
-Http port : 80
HTP-T800 User Manual
-18-
4. Remote Configuration
1. Remote Configuration
The server can be configured using web browser. Type IP address of HTP-T800 in the address input
area of Internet Explorer, then a live viewing screen will be displayed. Press Setup button located in
the upper right area of the monitoring screen, then the se page for server setup will be displayed.
The remote configuration window may be slightly different depends on the system modes (Encoder,
Decoder). The general explanation of the configuration in this manual is based on Encoder system
and differences according to the modes will be clarified when needed.
The configurations are grouped into 8 categories: System, Video, Audio, Network, Serial, Event,
Preset and User. Any configuration changes are not applied until Apply is pressed. Leaving the page
without pressing Apply button, changes in the page will be discarded.
2. Encoder Configuration
While most configuration items are common for Encoder, Decoder and Duplex mode, there are items
which are relevant to specific system mode. All the configuration items for Encoder mode were
explained first. Then, items specific only to Decoder and Duplex mode are described respectively.
Sections for Decoder and Duplex will not include items common for all modes.
cEnter IP Address dPress Setup button
HTP-T800 User Manual
-19-
2.1 System Configuration
System Mode
System mode: Select Encoder, Decoder.
System ID
System ID: Alphanumeric System ID to be transferred to remote software
Table of contents
Other Hunt Server manuals
