Huntington W3182901-R User manual

Touchless Basin Faucet
Instruction manual

www.hbfaucet.com
Troubleshooting 11
Suggested Tools 1
Components List 2
Product dimensions 3
Technical parameters 3
Care instructions 4
Installation steps 5
Operating guidelines 9
LED signal description １0
Contents

1
Suggested Tools
Tape measure
4 "AA" batteriesScrew driver
Electric drill
Adjustable wrench
Pencil
Please self-provided batteries.

2
Mounting parts
Battery box * 1
Battery box holder * 1
Install holder parts
Plastic expansion plug * 1
Screw * 1
Components List
Faucet body * 1
1/2 Connector * 2
Inlet Hose * 2
Filter screen * 2
Packing * 1
Nut * 2
Plate * 1
The product does not contain batteries, so please self-provided batteries.
!

3
∅55
123
[2.17"]
[4.84"]
171
[6.73"]
176
[6.93"]
119
[4.68"]
150
[5.91"]
D176 x W150 x H171 ∅55 mm
D6.93 " x W5.91" x H6.73" ∅ 2.17"
Technical parameters
Product dimensions
Function type
Power supply
Applicable water pressure
Sensing range
Power Waste
Inlet hose specification
Sensing time
limit time for water flow
Infrared Sensing
Four 'AA' alkaline batteries
0.05-0.8 ( MPa )
20 - 80 mm
< 0.5mW
G1/2 & 9/16-24UNFE-2B
open<1 Sec.,close<1 Sec.
90-second automatically stop water

4
Pay attention to close the shut off valve before cleaning the filter screen.
!
Disassemble the adapter.
A
Take out the filter screen
Clean or replace the filter screen.
B
Our products are metal products, so we need your attention to
avoid them being scratched.
We suggest using soft wet cloth to clean the product instead of
strong corrosive detergent.
1
2
When the faucet has been used for more
than 6 months or the flow becomes smaller.
Care instructions

5
1
First disassemble the mounting parts,
then insert the Faucet Body into the mounting hole,
and finally install the Locking Nut to fix the Faucet.
∅32-38mm
(1.25"-1.49")
Mounting
parts
Nest up to the top
Lock the nut to the tightest fixation.
Installation steps
Basin
countertops
Basin
countertops

6
2
Connect the water inlet hose, the hose with red label is connected with
hot water, and the hose with blue label is connected with cold water.
First, install the 1/2 connector and Filter screen washer attached to the
switch connector and tighten it with a wrench, then lock the Hose nut
to the connector thread by hand and tighten it with a wrench.
Tighten with a wrench.
H
Hot water pipe C Cold water pipe
1/2 Connector
Filter screen
Hose nut
Basin
countertops

7
3
Install the battery box. Connect the plug as shown in the figure.
Pay attention to the correct direction of the plug.
After connecting the battery box, it can be used normally.
Battery box
Battery box holder
Battery box plug
Basin
countertops
The product does not contain batteries, so please self-provided batteries.
!

8
Ground
Electric drill
1. Mark the drilling location with a pencil.
About 300mm(11.81")
or decide the drilling
distance by yourself.
∅6mm
(0.23")
Install the battery box holder,
Drill the hole with an electric drill first.
!
3. Lock the battery box holder. 4. Install 4 'AA' batteries.
2. Insert the plastic expansion plug after drilling. Tape measure
Screw driver

9
Note : the Faucet will stop water automatically after 90 second s.
!
Top view
Side view
COLD HOT
Adjust the temperature with the handle.
Wave switch
Sensing distance 3/4” to 3 1/8”
Operating guidelines

10
When the battery is connected, the LED light flashes for 2 times.
When sensing, the LED light flashes for 1 time and the water flows.
When sensing, the LED light flashes for 1 time and the water is off.
When the power is low, the LED light flashes rapidly for 5 times,
and there is no water out at this time.
1
2
3
4
LED signal description

11
!
In case of the following phenomenon, it may not be the product fault,
so it is necessary to solve the problem by yourself. If the problem cannot
be solved, please contact the local dealer or our company.
Phenomenon
No water
Too little water
Too much water
Short battery life
Cause of failure
The battery runs out
Water cut-off
The filter screen is too
dirty to cause blockage
The LED light is not on when
the machine is turned on
Or no action during induction
The water pressure is too low
Water supply shut down
The filter screen is too dirty
The water pressure is too low
The water pressure is too high
Use non alkaline or
inferior batteries
Processing method
Replace the battery
Check the water supply
Cleaning filter screen
Please send it for repair
Raise the pressure
Adjust water supply
Cleaning filter screen
Raise the pressure
Reduce the water pressure
Replace the battery
Troubleshooting

www.huntingtonbrass.com