Husky Mounts FS411 User manual

   
1
2
3
4
5
6
7
2
2
1
1
2
2
2
Long square tube
Short square tube
Pole with shelf add-on holes
Pole without holes
Pole connector
Tube connector
Tube connector cover
Front
Back
     
Thanks for choosing our TV Trolley Stand. This product was designed for mounting of flat panel televisions that weigh up to
60 kg /132lbs. It ensures the ease of adjusting the height of the TV. The stand can be easily moved by a set of integrated
wheels.
  Please go over the instructions at least once before taking any steps. If any aspect of the instructions stated
herein poses any confusions or doubts, please ensure to hire the services of a qualified installer. Carefully go through each
part supplied in the product package to ensure there are no missing or defective parts. DO NOT use defective parts, an
improper installation may cause damage or injuries. DO NOT use this product for any purposes that are not explicitly specified
in this document. WE WILL NOT BE LIABLE for any damages or injuries caused due to NOT FOLLOWING the precautions
stated in this manual."
 
1

   
10
12
8
9
4
11
4
2
2
13
14
14
8
Pole cover
Wheel & Washer
M6x10 allen head bolt
M6x60 allen head bolt
TV plate connector
& Rubber Pad
M6 socket plate4
15 Tool kit1
2
M5x6 Grub screw
16 1
Shelf
18 4
M4x6 countersink bolt
17 2
Shelf support

   
3
8
4
4
19 1
1
4
4
12
4
4
TV plate
TV arm set
M4x12 bolt
M4x30 bolt
M6x20 bolt
M6x35 bolt
M8x20 bolt
M8x35 bolt
M4 washer
M6 washer
20
21
22
23
24
25
26
27
28
M8 washer
M4 spacer
M6/M8 spacer(5mm)

4
1 2
34
56
9
1
211
3
UseTool kit(15) UseTool kit(15)
UseTool kit(15)
UseTool kit(15)
12 1
2
Front
Back
4
10
10
15
X2
X2
7
5
5
Cable Managment
Hole
5
13
6
6
8
8
Insert one wheel per tube (both wheel’s nuts are to be installed beneath the
tube, please see step 16)
Insert the plastic tube connector cover (part 4). However Please rememeber,
you will need to lift it up for step 15.
Insert the TV plate connector and the rubber pad (part 10) onto the poles (part
6) and then tighten the Allen screw.
Important: Long square tubes (part 1) should go in the front side. Short
square tubes (part 2) should go in the back side.Use the tube connector
(part 3) to connect the 4 square tubes.
Insert poles (part 5), make sure the hole for the screw (part 13) on the pole lines
up with the same hole on the tube connector (part 3). Insert the pole connector
(part 7) on top.
Insert tubes (part 6) into tubes (part 5) through the tube connector (part 7).
Insert the pole cover (part 8) on top of the tube (part 6).

5
7 8
9
19
13
25
15
21-23
24-26
27,28
(if necessary)
Level adjustment
UseTool kit(15)
UseTool kit(15)
10 11
Connect the TV plate into the poles.
Connect the the TV arms (part 20) into the back of the TV using the proper hardware (part 21-part 28). Note: you only need 4 screws, 4 washers and maybe
4
Adjust the TV plate to make sure it’s leveled.
Hook the two TV arms and the TV onto the TV plate, adjust to the proper tilting
angle and then tighten the tilting knobs. If the TV is heavy make sure you have
additional help.
Keep tightening the saftey screw until it passes the bottom rail of the TV plate.
DO NOT over tighten.
10. 1
10. 2
Safety bolt

6
14
16
Fasten grub screw
UseTool kit(15)
16
18
13 17
15
UseTool kit(15)
14
12 13
AdjustTV height Wire management
UseTool kit(15)
If the floor is not leveled and the stand is wobbly, turn the wheel’s nut up on the wobbly leg until the stand is leveled on the
floor and stable.
Adjust the height of the TV.
Install the shelf brackets (part 17) and the shelf (part 16). Lift tube connector cover (part 4), Fasten grab screw (part 14) for extra
stability.
Insert the wires into the pole for neat look.
15