Husky Mounts TL-400LM User manual

We Will Make It Stress Free
Please reach out to us if you have any questions
at all. 1-877-38-HUSKY(1-877-384-8759)
We are here to help!
55
MAX
"40kg
(88lbs)
RATED
40kg
(88lbs)
RATED
CAUTIO N: DO NOT EXCEED RATED
LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY
OCCUR!
INSTALLATION MANUAL
Tilting Wall Mount
TL-400LM
200x200/300x300
400x200/400x400

1
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
2
wall plate
A
(x1)
left a (x1)
B
dapter bracket
right adapter bracket (x1)
C
bubble level (x1)
D
Component Checklist
Package M
Package W
ST6.3x55 (x4)
W-A
concrete anchor
W-B
(x4) D6 washer
W-C
(x4)
M8x16
M-D
(x4)
M5x14
M-B
(x4) M6x14
M-C
(x4)
M4x14
M-A
(x4)
5mm spacer (x8)
M-J
M8x35
M-H
(x4)
M6x35
M-G
(x4)
M4x35
M-E
(x4) M5x35
M-F
(x4)
15mm spacer
M-K
(x4)
washer
M-I
(x4)
• Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings, please contact the seller.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone with good mechanical ability
who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
• Make sure that no electrical cable, water pipes or gas pipes are located within the
mounting surface in the wall.
• We hereby disclaim any and all liability for injury or damage arising from incorrect
assembly, incorrect mounting, or incorrect use of this product.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, please contact the seller for replacement.

4
3
WARNING
• Make sure that mounting screws are anchored into the center of the studs. The use of a stud
finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
Installers must verify that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
WARNING
Drill pilot holes
2
Drill pilot holes
21
3
Screw the wall
plate onto the
wall
X X
√
Screw the wall
plate onto the
wall
X X
√
Find and mark the
exact location of
mounting holes
1
Mark the exact
location of
mounting holes
ø 4.5mm
(ø 3/16")
55mm
(2.2")
55mm
(2.2")60mm
(2.4")
60mm
(2.4")
ø 10mm
(ø 3/8")
D
W-B
W-C
W-A
D
X
W-A
W-C
1a. For Wood Stud Wall Mounting (do not use Concrete anchors W-B) 1b. For Solid Brick and Concrete Mounting
(the use of the concrete anchors W-B is necessary)

M-E
M-F
M-G
M-H
M-I
M-K
M-J
M-E
M-F
M-G
M-H
M-I
M-K
M-J
M-E
M-F
M-G
M-H
M-I
M-K
M-D
M-I
M-J
65
2. Installing the Adapter Brackets
3. Hanging the TV onto the Wall Plate
Top of the TV
2-2 For Recessed Back Screens or to Access A/V Inputs
TV
TV
TV
2-1 For Flat Back Screens
TV
TV
TV
or or or
M-A
M-B
M-C
M-D
M-I
4mm
+12°
-12°
wall wall
Tighten all screws but do not over tighten.
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.
· if the spacers are used, they should be placed between the mounting arms and the back of TV, and not
between the mounting arms and the head of the screw.
· Position the adapter brackets as close as possible to the center of the TV.
· Screw the adapter brackets onto the TV.