Husqvarna AUTOMOWER 210 C User manual

AUTOMOWER™ is a trademark owned by Husqvarna AB. Copyright © 2008 HUSQVARNA. All rights reserved.
HUSQVARNA AUTOMOWER™
210 C
QUICK GUIDE
www.Automower™.com
115 13 03 -26
5STARTING AND STOPPING AUTOMOWER™
See chapters 4.1 and 4.2 in the Operator’s Manual.
STARTING
1. Open the control panel cover by pressing the STOP
button.
2. Set the main switch to ON position.
3. Enter the PIN code, confirm with the YES button.
4. Close the cover.
STOPPING
Press the STOP button.
USE
Automower™ is recommended for lawns up to 500 m² /
0.12 acre. The size of the working area the mower can
handle depends on how much it is used. The larger the lawn
the more occasions per week Automower™ can work.
2
3
4
41. Connect the loop generator/charger charging cable to the
mower’s charger contact. The boundary loop must be
connected to a mains connected loop generator/charger.
2. Set the main switch to ON position.
3. Select and enter a four digit PIN code. All combinations
except 0000 are permitted.
4. Press the YES button.
5. Confirm the selected PIN code by re-entering the PIN
code.
6. Press the YES button.
When you have selected a PIN code, the mower and loop
generator/charger are linked to each other and the mower
can be operated.
LINKING AUTOMOWER™ TO THE LOOP GENERATOR/CHARGER
See chapter 3.7 in the Operator’s Manual
1
2
3
EN_QG_2009_210C (kopia).indd 1 08-11-14 10.27.25

30 cm
Zone 1
Zone 2
30 cm / 12” 35 cm / 14”
10 cm / 4”
0 cm / 0”
GETTING STARTED WITH
HUSQVARNA AUTOMOWER™
31. Open the connector and run the wire ends in the recesses
on each connector.
2. Press the connector together using a pair of pliers.
3. Cut off any surplus boundary wire.
Cut 1-2 cm / 0.5” above the connector.
4. Attach the connector to the contact pin on the loop
generator/charger.
1
2
PLACEMENT AND CONNECTION OF LOOP GENERATOR/CHARGER
AND CHARGING OF BATTERY
PLACING THE BOUNDARY WIRE
See 3.4 in the Operator’s Manual
1. Run the boundary wire ensuring it
forms a loop around the work area.
See chapters 3.2 and 3.3 in the Operator’s Manual.
1. The loop generator/charger must be placed where it is well
ventilated and is not exposed to direct sunlight.
2. Connect the loop generator/charger’s power cord to a
mains wall socket. The 120V transformer (USA) is for
indoor use only.
3. Connect the charger cable from the loop generator/
charger to the charger contact on the mower. The green
indicator lamp Battery should now now be lit with a
steady light.
Loop generator/charger Boundary wire and
coupler
Clinchers Connector Measurement gauge
CONNECTING THE BOUNDARY WIRE
See chapter 3.5 in the Operator’s Manual
2
1
4
3
2
3
1. Catch button to open the cutting
height adjustment cover
2. STOP button
3. Charger contact
4. Connection to boundary wire
5. LED for per formance inspection
of boundary wire
6. Indicator lamps
7. Keypad
1
2
3
4
5
6
7
ZONE C LASSIFICATION
If the mowing results in the garden are uneven due to the
shape of the garden, for example because of a long passage,
you have the option of dividing up your garden into zones.
When the mower is placed in zone 1, it will not mow in zone
2 and vice versa. Move the mower between the zones to
maintain even mowing results.
EN_QG_2009_210C (kopia).indd 2 08-11-14 10.27.29