Husqvarna 122ldx SERIES User manual

EE
EEnn nngg ggll llii iiss sshh hh (( ((22 22-- --22 2244 44)) ))
FF
FFrr rree eenn nncc cchh hh (( ((22 2255 55-- --44 4488 88)) ))
SS
SSpp ppaa aann nnii iiss sshh hh (( ((44 4499 99-- --77 7722 22)) ))
122C 122LD
x-series
Oper ator’ s man ual
Man uel d’utilisation
Man ual de instr ucciones
Please r ead the operator’ s man ual car efull y and mak e sur e y ou understand the instructions bef or e using the machine .
Lir e attentiv ement et bien assimiler le man uel d’utilisation a vant d’utiliser la machine .
Lea detenidamente el man ual de instrucciones y asegúr ese de entender su contenido antes de utilizar la máquina.
EE
EEnn nngg ggll llii iiss sshh hh (( ((22 22-- --22 2244 44)) ))
FF
FFrr rree eenn nncc cchh hh (( ((22 2255 55-- --44 4488 88)) ))
SS
SSpp ppaa aann nnii iiss sshh hh (( ((44 4499 99-- --77 7722 22)) ))

KEY T O SYMBOLS
2 –
English
Symbolsonthemac hineand/orin
the manual:
W ARNING! Clearing saws,
brushcutters and trimmers can be
dangerous! Careless or incorrect use
can result in serious or fatal injury to
the operator or others.It is extremely
important that you read and
understand the contents of the operator’s manual.
Please read the operator’s manual
carefully and make sure you
understand the instructions before
using the machine.
Always wear:
A protective helmet where there is a
risk of falling objects
• Approved hearing protection
• Approved eye protection
Max. speed of output shaft, rpm
Watch out for thrown objects and
ricochets.
The operator of the machine must
ensure, while working, that no
persons or animals come closer than
15 metres.
Always wear approved protective
gloves.
Wear sturdy, non-slip boots.
Only use non-metallic, flexible
cutting attachments, i.e. trimmer
heads with trimmer cord.
Other symbols/decals on the mac hine refer to special
certification requirements for certain markets.
The engine is s witched off by moving
the stop switch to the stop position.
CAUTION! The stop switch
automatically returns to the start
position. In order to prevent
unintentional starting, the spark plug
cap must be removed from the spark plug when
assembling, checking and/or performing maintenance.
Always wear approved protective
gloves.
Regular cleaning is required.
Visual check.
10000
50FT
15 m
50FT
15 m
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.

CONTENTS
English
–
3
Contents Note the f ollowing before
starting:
Please read the oper ator’s manual carefully.
Maintenance, replacement, or repair of the emission
control devices and system may be performed by any
nonroad engine repair establishment or individual.
The Emissions Compliance Period referred to on the
Emission Compliance label indicates the number of
operating hours for which the engine has been shown to
meet Federal and Californian emissions requirements.
KEY TO SYMBOLS
Symbols on the machine and/or in the man ual: ... 2
CONTENTS
Contents ............................................................... 3
Note the following before starting: ........................ 3
INTR ODUCTION
Dear customer! ..................................................... 4
WHA T ISWHAT?
What is what on the g rass trimmer? ..................... 5
GENERAL SAFETY PRECA UTIONS
Impor tant .............................................................. 6
Personal protective equipment ............................. 6
Machine ′ s safety equipment ................................. 7
Cutting equipment ................................................ 9
ASSEMBL Y
Fitting the loop handle .......................................... 10
Fitting the trimmer guard and trimmer head ......... 10
Assembling and dismantling the two-piece shaft . 10
FUEL HANDLING
Fuel saf ety ............................................................ 12
Fuel ...................................................................... 12
Fueling .................................................................. 13
ST ARTING AND STOPPING
Chec k before starting ........................................... 14
Starting and stopping ........................................... 14
W ORKINGTECHNIQUES
Gener al working instructions ................................ 15
MAINTENANCE
Carb uretor ............................................................ 17
Muffler .................................................................. 17
Cooling system ..................................................... 18
Spark plug ............................................................ 18
Two-piece shaft ................................................... 18
Air filter ................................................................. 19
Maintenance schedule ......................................... 20
TECHNICAL D ATA
T echnical data ...................................................... 21
FEDERAL AND CALIFORNIA EMISSIONS
CONTROLWARRANTY STATEMENT
Y OURWARRANTY RIGHTS AND OBLIGATIONS 23
!
W
ARNING! Long-term exposure to noise
can result in permanent hearing
impairment. So always use approved
hearing protection.
!
W ARNING! Under no circumstances may
the design of the machine be modified
without the permission of the
manufacturer. Always use genuine
accessories. Non-authorized
modifications and/or accessories can
result in serious personal injury or the
death of the operator or others.
Your warranty may not cover damage or
liability caused by the use of non-
authorized accessories or replacement
parts.
!
W ARNING! A clearing saw, brushcutter
or trimmer can be dangerous if used
incorrectly or carelessly, and can cause
serious or fatal injury to the operator or
others. It is extremely important that you
read and understand the contents of this
operator’s manual.

4 –
English
INTR
ODUCTION
Dear customer!
Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689,
when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production
of muskets.The location was logical, since water power was harnessed from the Huskvarna River to create the water-
powered plant.During over 300 years of continuous operation, the Husqvarna factory has produced a lot of different
products, from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc.In 1956, the first
motor driven lawn mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working
today.
Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our
highest priority.We develop, manufacture and market high quality motor driven products for forestry and gardening as
well as for building and construction industry.
Your purchase gives you access to professional help with repairs and service whenever this may be necessary. If the
retailer who sells your machine is not one of our authorized dealers, ask for the address of your nearest servicing dealer.
It is our wish that you will be satisfied with your product and that it will be your companion for a long time.Think of this
operator
′ s manual as a valuable document.By following its ′ content (using, service, maintenance etc) the life span and
the second-hand value of the machine can be extended. If you ever lend or sell this machine, make sure that the
borrower or buyer gets the operator ′ s manual, so they will also know how to properly maintain and use it.
Thank you for using a Husqvarna product.
Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and
appearance of products without prior notice.
For customer assistance, contact us at our website:www.usa.husqvarna.com

English –
5
WHA T IS WHA
T?
What is what on the grass trimmer?
14
15
19
3
2
4
5
6
8
7
10
11
12
13
122C
16
1
18 19
23
17
10
11
5
4
713
8
12 16
9
9
122LDx-series
20
2
1 Trimmer head
2 Cutting attachment guard
3 Shaft
4 Loop handle
5 Throttle trigger
6 Stop switch
7 Throttle lockout
8 Spark plug cap and spark plug
9 Starter
10 Fuel tank
11 Air filter cover
12 Air purge.
13 Choke control
14 Operator’s manual
15 Combination spanner
16 Starter
17 Shaft coupling
18 Bevel gear
19 Grease filler cap, bevel gear
20 Drive disc

GENERAL SAFETY PRECA UTIONS
6 –
English
Impor tant
Personal protective equipment
HELMET
A protectiv e helmet where there is a risk of falling objects
HEARING PROTECTION
Wear hearing protection that provides adequate noise
reduction.
EYE PROTECTION
Always wear approved eye protection.If you use a visor
then you must also wear approved protective goggles.
Approved protective goggles must comply with standard
ANSI Z87.1 in the USA or EN 166 in EU countries.
IMPORTANT!
The machine is only designed for trimming grass.
The only accessories you can operate with this engine
unit are the cutting attachments we recommend in the
chapter on Technical data.
Neverusethemachine ifyouaretired, if youhavedrunk
alcohol, or if you are taking medication that could affect
your vision, your judgement or your co-ordination.
Wear personal protective equipment.See instructions
under the heading ”Personal protective equipment”.
Never use a machine that has been modified in any way
from its original specification.
Never use a machine that is faulty.Carry out the checks,
maintenance and service instructions described in this
manual.Some maintenance and service measures
must be carried out by trained and qualified specialists.
See instructions under the heading Maintenance.
All covers, guards and handles must be fitted before
starting. Ensure that the spark plug cap and ignition
lead are undamaged to avoid the risk of electric shock.
The machine operator must ensure that no people or
animals come closer than 15 metres while working.
When several operators are working in the same area
the safety distance should be at least twice the tree
height and no less than 15 metres.
Do an overall inspection of the machine before use, see
maintenance schedule.
!
W
ARNING!This machine produces an
electromagnetic field during operation.
This field may under some
circumstances interfere with active or
passive medical implants.To reduce the
risk of serious or fatal injury, we
recommend persons with medical
implants to consult their physician and
the medical implant manufacturer before
operating this machine.
!
W
ARNING! Running an engine in a
confined or badly ventilated area can
result in death due to asphyxiation or
carbon monoxide poisoning.
!
W ARNING! Never allow children to use or
be in the vicinity of the machine. As the
machine is equipped with a spring-
loaded stop switch and can be started by
low speed and force on the starter
handle, even small children under some
circumstances can produce the force
necessary to start the machine.This can
mean a risk of serious personal injury.
Therefore remove the spark plug cap
when the machine is not under close
supervision.
IMPOR TANT!
A clearing saw, brushcutter or trimmer can be
dangerous if used incorrectly or carelessly, and can
cause serious or fatal injury to the operator or others.It
isextremelyimportantthatyoureadand understand the
contents of this operator’s manual.
You must use approved personal protective equipment
whenever you use the machine. Personal protective
equipment cannot eliminate the risk of injury but it will
reduce the degree of injury if an accident does happen.
Askyourdealer for helpin choosing theright equipment.
!
W
ARNING! Listen out for warning signals
or shouts when you are wearing hearing
protection. Always remove your hearing
protection as soon as the engine stops.

GENERAL SAFETY PRECA UTIONS
English
–
7
GLO VES
Gloves should be worn when necessary, e.g., when fitting
cutting attachments.
BOOTS
Wear sturdy, non-slip boots.
CLOTHING
Wear clothes made of a strong fabric and avoid loose
clothing that can catch on twigs and branches. Always
wear heavy, long pants.Do not wear jewellery, shorts
sandalsorgobarefoot.Securehairsoitis aboveshoulder
level.
FIRST AID KIT
Always have a first aid kit nearby.
Mac hine ′ s safety equipment
This section describes the machine′s safety equipment,
its purpose, and how checks and maintenance should be
carried out to ensure that it operates correctly. See the
”What is what?”section to locate where this equipment is
positioned on your machine.
The life span of the machine can be reduced and the risk
of accidents can increase if machine maintenance is not
carried out correctly and if service and/or repairs are not
carried out professionally. If you need further information
please contact your nearest servicing dealer.
Throttle lockout
The throttle lockout is designed to prevent accidental
operation of the throttle control.When you press the lock
(A)(i.e.when yougraspthe handle) itreleasesthe throttle
control (B).When you release the handle the throttle
control and the throttle lockout both move back to their
original positions.This movement is controlled by two
independentreturn springs.Thisarrangementmeansthat
the throttle control is automatically locked at the idle
setting.
Make sure the throttle control is locked at the idle setting
when the throttle lockout is released.
Press the throttle lockout and make sure it returns to its
original position when you release it.
Check that the throttle trigger and throttle lockout move
freely and that the return springs work properly.
IMPORTANT!
All servicing and repair work on the machine requires
special training.This is especially true of the machine′s
safety equipment. If your machine fails any of the
checks described below you must contact your service
agent.When you buy any of our products we guarantee
the availability of professional repairs and service.If the
retailer who sells your machine is not a servicing dealer,
ask him for the address of your nearest service agent.
!
WARNING! Never use a machine with
faulty safety equipment.The machine’s
safety equipment must be checked and
maintained as described in this section.
If your machine fails any of these checks
contact your service agent to get it
repaired.

GENERAL SAFETY PRECAUTIONS
8 – English
See instructions under the heading Start. Start the
machine and apply full throttle.Release the throttle and
check that the cutting attachment stops and remains at a
standstill.Ifthe cuttingattachmentrotates withthethrottle
in the idle position then the carburettor idle setting must
be checked. See instructions under the heading
Maintenance.
Stop switch
Use the stop switch to switch off the engine.
Start the engine and make sure the engine stops when
you move the stop switch to the stop setting.
Cutting attachment guard
Thisguardisintended to preventlooseobjectsfrom being
thrown towards the operator.The guard also protects the
operator from accidental contact with the cutting
attachment.
Check that the guard is undamaged and not cracked.
Replace the guard if it has been exposed to impact or is
cracked.
Always use the recommended guard for the cutting
attachment you are using.See chapter onTechnical data.
Muffler
Themuffleris designed tokeepnoiselevels to aminimum
and to direct exhaust fumes away from the user.A muffler
fitted with a catalytic converter is also designed to reduce
harmful exhaust gases.
In countries that have a warm and dry climate there is a
significant risk of fire.We therefore fit certain mufflers with
a spark arrestor screen. Check whether the muffler on
your machine is fitted with this kind of screen.
For mufflers it is very important that you follow the
instructions on checking, maintaining and servicing your
machine.
Never use a machine that has a faulty muffler.
Regularly check that the muffler is securely attached to
the machine.
If the muffler on your machine is fitted with a spark
arrestor screen this must be cleaned regularly.A blocked
screen will cause the engine to overheat and may lead to
serious damage.
!
WARNING! Never use a cutting
attachment without an approved guard.
See the chapter onTechnical data. If an
incorrect or faulty guard is fitted this can
cause serious personal injury.
!
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.
This also applies at idle speed. Contact
can result in burns to the skin.
Remember the risk of fire!

GENERAL SAFETY PRECAUTIONS
English – 9
Cutting equipment
This section describes how to choose and maintain your
cutting equipment in order to:
• Reduce the risk of blade thrust.
• Obtain maximum cutting performance.
• Extend the life of cutting equipment.
Trimmer head
• Only use the recommended trimmer heads and
trimmer cords.These have been tested by the
manufacturer to suit a particular engine size.This is
especially important when a fully automatic trimmer
head is used. Only use the recommended cutting
attachment. See the chapter on Technical data.
• Smaller machines generally require small trimmer
heads and vice versa.This is because when clearing
using a cord the engine must throw out the cord
radially from the trimmer head and overcome the
resistance of the grass being cleared.
• The length of the cord is also important.A longer cord
requires greater engine power than a shorter cord of
the same diameter.
• Make sure that the cutter on the trimmer guard is
intact.This is used to cut the cord to the correct length.
• To increase the life of the cord it can be soaked in
water for a couple of days.This will make the line
tougher so that it lasts longer.
!
WARNING!The inside of the muffler
contain chemicals that may be
carcinogenic. Avoid contact with these
elements in the event of a damaged
muffler.
!
WARNING! Bear in mind that:
The exhaust fumes from the engine are
hot and may contain sparks which can
start a fire. Never start the machine
indoors or near combustible material!
!
IMPORTANT!
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
Refer to the instructions for the cutting attachment to
check the correct way to load the cord and the correct
cord diameter.
!
WARNING! Always stop the engine
before doing any work on the cutting
attachment.This continues to rotate even
after the throttle has been released.
Ensure that the cutting attachment has
stopped completely and disconnect the
HT lead from the spark plug before you
start to work on it.
!
WARNING! A faulty cutting attachment
may increase the risk of accidents.
IMPORTANT!
Always ensure the trimmer cord is wound tightly and
evenly around the drum, otherwise the machine will
generate harmful vibration.

ASSEMBLY
10 – English
Fitting the loop handle
•Clip the loop handle onto the shaft.Note that the loop
handle must be fitted between the arrows on the shaft.
• Fit the bolt, securing plate and wing nut as shown in
the diagram.Tighten the wing nut.
Fitting the trimmer guard and
trimmer head
• Fit the guard as shown in the diagram.Tighten
securely.
• Fit the dust cup on the shaft.The nut must be
completely covered by the dust cup.
• Hold the dust cup with a spanner to prevent the shaft
from rotating.
• Screw the trimmer head onto the shaft.
Assembling and dismantling the
two-piece shaft (122LDx-series)
Assembly:
• Loosen the coupling by turning the knob.
• Align the tab of the attachment (A) with the arrow on
the coupling (B).
• Push the attachment into the coupling until the
attachment snaps into place.
Before using the unit, tighten the knob securely.
A
B

ASSEMBLY
English – 11
Dismantling:
• Loosen the coupling by turning the knob (at least 3
times).
• Push and hold the button (C).While securely holding
the engine end, pull the attachment straight out of the
coupling.
C

FUEL HANDLING
12 – English
Fuel safety
Never start the machine:
1 If you have spilled fuel on it.Wipe off the spillage and
allow remaining fuel to evaporate.
2 If you have spilled fuel on yourself or your clothes,
change your clothes.Wash any part of your body that
has come in contact with fuel. Use soap and water.
3 If the machine is leaking fuel. Check regularly for
leaks from the fuel cap and fuel lines.
Transport and storage
•Storeandtransport the machineandfuelsothatthere
is no risk of any leakage or fumes coming into contact
with sparks or naked flames, for example, from
electrical machinery, electric motors, electrical relays/
switches or boilers.
• When storing and transporting fuel always use
approved containers intended for this purpose.
• When storing the machine for long periods the fuel
tank must be emptied.Contact your local gas station
to find out where to dispose of excess fuel.
• Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
• The transport guard must always be fitted to the
cutting attachment when the machine is being
transported or in storage.
• Secure the machine during transport.
• Inordertopreventunintentionalstartingoftheengine,
the spark plug cap must always be removed during
long-term storage, if the machine is not under close
supervision and when performing all service
measures.
Fuel
CAUTION! The machine is equipped with a two-stroke
engine and must always been run using a mixture of
gasoline and two-stroke engine oil. It is important to
accurately measure the amount of oil to be mixed to
ensure that the correct mixture is obtained.When mixing
small amounts of fuel, even small inaccuracies can
drastically affect the ratio of the mixture.
Gasoline
CAUTION! Always use a quality gasoline/oil mixture with
an octane rating of at least 87 octane ((RON+MON)/2).If
your machine is equipped with a catalytic converter (see
chapter on Technical data) always use a good quality
unleaded gasoline/oil mixture.Leaded gasoline will
destroy the catalytic converter.
Use low-emission gasoline, also known as alkylate
gasoline, if it is available.
This engine is certified to operate on unleaded
gasoline.
• The lowest recommended octane grade is 87
((RON+MON)/2).If you run the engine on a lower
octane grade than 87 so-called knocking can occur.
This gives rise to a high engine temperature and
increased bearing load, which can result in serious
engine damage.
• Whenworkingatcontinuoushighrevsahigheroctane
rating is recommended.
Two-stroke oil
• For best results and performance use HUSQVARNA
two-strokeengine oil,whichis speciallyformulated for
our air-cooled two stroke-engines.
• Never use two-stroke oil intended for water-cooled
engines, sometimes referred to as outboard oil (rated
TCW).
• Never use oil intended for four-stroke engines.
• Mixing ratio
1:50 (2%) with HUSQVARNA two-stroke oil.
!
WARNING!Take care when handling fuel.
Bear in mind the risk of fire, explosion
and inhaling fumes.
!
WARNING! Fuel and fuel fumes are
highly inflammable and can cause
serious injury when inhaled or allowed to
come in contact with the skin. For this
reason observe caution when handling
fuel and make sure there is adequate
ventilation.
Gasoline, litre Two-stroke oil, litre
2% (1:50)
5 0,10
10 0,20
15 0,6/0,30
20 0,40
US gallon US fl. oz.
1 2 1/2
2 1/2 6 1/2
5 12 7/8

FUEL HANDLING
English – 13
Mixing
• Always mix the gasoline and oil in a clean container
intended for fuel.
• Always start by filling half the amount of the gasoline
to be used.Then add the entire amount of oil. Mix
(shake) the fuel mixture.Add the remaining amount of
gasoline.
• Mix (shake) the fuel mixture thoroughly before filling
the machine’s fuel tank.
• Do not mix more than one month’s supply of fuel at a
time.
• If the machine is not used for some time the fuel tank
should be emptied and cleaned.
Fueling
•If you have spilled fuel on it.Wipe off the spillage and
allow remaining fuel to evaporate.
• Clean the area around the fuel cap. Contamination in
the tank can cause operating problems.
• Ensure that the fuel is well mixed by shaking the
container before filling the tank.
!
WARNING!The catalytic converter
muffler gets very hot during and after
use.This also applies during idling. Be
aware of the fire hazard, especially when
working near flammable substances and/
or vapours.
!
WARNING!Taking the following
precautions, will lessen the risk of fire:
Mix and pour fuel outdoors, where there
are no sparks or flames.
Do not smoke or place hot objects near
fuel.
Always shut off the engine before
refuelling.
Always stop the engine and let it cool for
a few minutes before refuelling.
When refuelling,open the fuel cap slowly
so that any excess pressure is released
gently.
Tighten the fuel cap carefully after
refuelling.
Always move the machine away from the
refuelling area and source before
starting.

STARTING AND STOPPING
14 – English
Check before starting
• Check that the trimmer head and trimmer guard are
notdamagedorcracked.Replace the trimmerheador
trimmer guard if they have been exposed to impact or
are cracked.
• Never use the machine without a guard nor with a
defective guard.
• All covers must be correctly fitted and undamaged
before you start the machine.
Starting and stopping
Starting
Primer bulb: Press the air purge repeatedly until fuel begins
to fill the bulb.The bulb need not be completely filled.
Choke: Set the choke control in the choke position.
Hold the body of the machine on the ground using your
left hand (CAUTION! Not with your foot!). Grip the starter
handle, slowly pull out the cord with your right hand until
you feel some resistance (the starter pawls grip), now
quickly and powerfully pull the cord. Never wrap the
starter cord around your hand
Repeat pulling the cord until the engine starts.When the
engine starts. return choke control to run position and
apply full throttle;the throttle will automatically disengage
from the start setting.
CAUTION! Do not pullthestarter cordallthe wayoutand
do not let go of the starter handle when the cord is fully
extended.This can damage the machine.
Stopping
Stop the engine by switching off the ignition.
CAUTION! The stop switch automatically returns to the
start position. In order to prevent unintentional starting,
the spark plug cap must be removed from the spark plug
when assembling, checking and/or performing
maintenance.
!
WARNING!The complete clutch cover and
shaft must be fitted before the machine is
started, otherwise the clutch can come
loose and cause personal injury.
Always move the machine away from the
refuelling area and source before starting.
Place the machine on a flat surface. Ensure
the cutting attachment cannot come into
contact with any object.
Make sure no unauthorised persons are
in the working area, otherwise there is a
risk of serious personal injury.The safety
distance is 15 metres.
!
WARNING!When the engine is started
with the choke in choke position the
cutting attachment will start to rotate
immediately.

WORKINGTECHNIQUES
English – 15
General working instructions
Basic safety rules
1 Look around you:
• To ensure that people, animals or other things cannot
affect your control of the machine.
• To ensure that people, animals, etc., do not come into
contact with the cutting attachment or loose objects
that are thrown out by the cutting attachment.
• CAUTION! Do not use the machine unless you are
able to call for help in the event of an accident.
2 Inspect the working area. Remove all loose objects,
such as stones, broken glass, nails, steel wire, string,
etc. that could be thrown out or become wrapped
around the cutting attachment.
3 Do not use the machine in bad weather, such as
dense fog, heavy rain, strong wind, intense cold, etc.
Working in bad weather is tiring and often brings
added risks, such as icy ground, unpredictable felling
direction, etc.
4 Make sure you can move and stand safely.Check the
area around you for possible obstacles (roots, rocks,
branches, ditches, etc.) in case you have to move
suddenly.Take great care when working on sloping
ground.
5 Keep a good balance and a firm foothold.Do not
overreach. Keep proper footing and balance at all
times.
6 Always hold the machine with both hands. Hold the
machine on the right side of your body.Keep all parts
of your body away from the hot surfaces.Keep all
parts of your body away from the rotating cutting
attachment.
7 Keep the cutting attachment below waist level.
8 The engine must be switched off before moving.
9 Never put the machine down with the engine running
unless you have it in clear sight.
IMPORTANT!
This section takes up the basic safety precautions for
working with a trimmer.
If you encounter a situation where you are uncertain
how to proceed you should ask an expert.Contact your
dealer or your service workshop.
Avoid all usage which you consider to be beyond your
capability.
You must understand the difference between forestry
clearing, grass clearing and grass trimming before use.
!
WARNING! Neither the operator of the
machine nor anyone else may attempt to
remove the cut material while the engine
is running or the cutting equipment is
rotating, as this can result in serious
injury.
Stop the engine and cutting equipment
before you remove material that has
wound around the blade shaft as
otherwise there is a risk of injury.The
bevel gear can get hot during use and
may remain so for a while afterwards.You
could get burnt if you touch it.
!
WARNING!Watch out for thrown objects.
Always wear approved eye protection.
Never lean over the cutting attachment
guard. Stones, rubbish, etc. can be
thrown up into the eyes causing
blindness or serious injury.
Keep unauthorised persons at a
distance. Children, animals, onlookers
and helpers should be kept outside the
safety zone of 15 m. Stop the machine
immediately if anyone approaches.Never
swing the machine around without first
checking behind you to make sure no-
one is within the safety zone.

WORKINGTECHNIQUES
16 – English
Basic working techniques
Always slow the engine to idle speed after each working
operation.Long periods at full throttle without any load on
the engine can lead to serious engine damage.
Grass trimming with a trimmer head
Trimming
• Hold the trimmer head just above the ground at an
angle.It is the end of the cord that does the work.Let
the cord work at its own pace.Never press the cord
into the area to be cut.
• The cord can easily remove grass and weeds up
against walls, fences, trees and borders, however it
can also damage sensitive bark on trees and bushes,
and damage fence posts.
• Reduce the risk of damaging plants by shortening the
cord to 10-12 cm and reducing the engine speed.
Clearing
• T he clearing technique removes all unwanted
vegetation.Keep thetrimmer headjust abovetheground
andtilt it.Let theend ofthe cord strikethegroundaround
trees, posts, statues and the like.CAUTION! This
technique increases the wear on the cord.
• Thecord wearsquicker andmust be fed forward more
often when working against stones, brick, concrete,
metalfences, etc.,thanwhencomingintocontact with
trees and wooden fences.
• When trimming and clearing you should use less than
full throttle so that the cord lasts longer and to reduce
the wear on the trimmer head.
Cutting
•The trimmer is ideal for cutting grass that is difficult to
reach using a normal lawn mower.Keep the cord
paralleltothegroundwhencutting.Avoid pressing the
trimmer head against the ground as this can ruin the
lawn and damage the tool.
• Do not allow the trimmer head to constantly come into
contact with the ground during normal cutting.
Constant contact of this type can cause damage and
wear to the trimmer head.
Sweeping
• The fan effect of the rotating cord can be used for quick
and easy clearing up.Hold the cord parallel to and above
the area to be swept and move the tool to and fro.
• Whencuttingand sweepingyoushould use fullthrottleto
obtain the best results.
!
WARNING! Sometimes branches or
grass get caught between the guard and
cutting attachment. Always stop the
engine before cleaning.
!
WARNING! Overexposure to vibration
can lead to circulatory damage or nerve
damage in people who have impaired
circulation. Contact your doctor if you
experience symptoms of overexposure
to vibration. Such symptoms include
numbness, loss of feeling, tingling,
pricking, pain, loss of strength, changes
in skin colour or condition.These
symptoms normally appear in the
fingers, hands or wrists.The risk
increases at low temperatures.

MAINTENANCE
English – 17
Carburetor
Adjustment of the idle speed
Before any adjustments are made, make sure that the air
filter is clean and the air filter cover is fitted.
Adjust the idle speed using the idle adjustment screwT, if
it is necessary to readjust. First turn the idle adjustment
screwT clockwise until the cutting attachment starts to
rotate.Then turn the screw anticlockwise until the cutting
attachment stops.The idle speed is correctly adjusted
when the engine will run smoothly in every position.The
idle speed should also be well below the speed at which
the cutting attachment starts to rotate.
Rec. idle speed: See the Technical data section.
Muffler
CAUTION! Some mufflers are fitted with a catalytic
converter.See chapter on Technical data to see whether
your machine is fitted with a catalytic converter.
The muffler is designed to reduce the noise level and to
direct the exhaust gases away from the operator.The
exhaustgasesarehot and cancontainsparks,whichmay
cause fire if directed against dry and combustible
material.
Some mufflers are equipped with a special spark arrestor
screen. If your machine has this type of muffler, you
should clean the screen at least once a week.This is best
done with a wire brush. On mufflers without a catalytic
converter the screen should be cleaned weekly, or
replaced if necessary. On mufflers fitted with a catalytic
converter thescreenshouldbechecked, and ifnecessary
cleaned,monthly.If the screen is damaged it should be
replaced. If the screen is frequently blocked, this can be
a sign that the performance of the catalytic converter is
impaired. Contact your dealer to inspect the muffler. A
blocked screen will cause the machine to overheat and
result in damage to the cylinder and piston.
CAUTION! Never use a machine with a defective muffler.
!
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until
it has been correctly adjusted or
repaired.
!
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.
This also applies at idle speed. Contact
can result in burns to the skin.
Remember the risk of fire!

MAINTENANCE
18 – English
Cooling system
To keep the working temperature as low as possible the
machine is equipped with a cooling system.
The cooling system consists of:
1 Air intake on the starter.
2 Cooling fins on the cylinder.
Cleanthe coolingsystem with abrushonce aweek,more
often in demanding conditions.A dirty or blocked cooling
system results in the machine overheating which causes
damage to the piston and cylinder.
Spark plug
The spark plug condition is influenced by:
• Incorrect carburetor adjustment.
• An incorrect fuel mixture (too much or incorrect type
of oil).
• A dirty air filter.
These factors cause deposits on the spark plug
electrodes, which may result in operating problems and
starting difficulties.
If the machine is low on power, difficult to start or runs
poorly at idle speed: always check the spark plug first
before taking any further action. If the spark plug is dirty,
cleanitandcheckthat theelectrode gap is0.020 inch (0,5
mm).The spark plug should be replaced after about a
month in operation or earlier if necessary.
CAUTION! Always use the recommended spark plug
type! Use of the wrong spark plug can damage the piston/
cylinder. Check that the spark plug is fitted with a
suppressor.
Two-piece shaft
Thedriveshaftendin thelowershaftshould be lubricated
with grease every 30 hours.There is a risk that the drive
shaft ends (splined coupling) on models with two-piece
shafts will seize if they are not lubricated regularly.
1
2

MAINTENANCE
English – 19
Air filter
The air filter must be regularly cleaned to remove dust
and dirt in order to avoid:
• Carburettor malfunctions
• Starting problems
• Loss of engine power
• Unnecessary wear to engine parts
• Excessive fuel consumption.
Clean the filter every 25 hours, or more regularly if
conditions are exceptionally dusty.
Cleaning the air filter
Remove the air filter cover and take out the filter.Wash it
clean in warm, soapy water.Ensure that the filter is dry
before refitting it.
An air filter that has been in use for a long time cannot be
cleaned completely.The filter must therefore be replaced
with a new one at regular intervals.A damaged air filter
must always be replaced.
If the machine is used in dusty conditions the air filter
should be soaked in oil.See instructions under the
heading Oiling the air filter.
Oiling the air filter
Always use HUSQVARNA filter oil, art. no.531 00 92-48.
The filter oil contains a solvent to make it spread evenly
through the filter.You should therefore avoid skin contact.
Put the filter in a plastic bag and pour the filter oil over it.
Knead the plastic bag to distribute the oil. Squeeze the
excess oil out of the filter inside the plastic bag and pour
offthe excessbeforefitting the filtertothemachine.Never
usecommon engineoil.Thiswoulddrain through thefilter
quite quickly and collect in the bottom.
Bevel gear
The bevel gear is filled with the right quantity of grease at
the factory. However, before using the machine you
should check that the bevel gear is filled three-quarters
full with grease.Use HUSQVARNA special grease.
The grease in the bevel gear does not normally need to
be changed except if repairs are carried out.

20 – English
MAINTENANCE
Maintenance schedule
The following is a list of the maintenance that must be performed on the machine.Most of the items are described in the
Maintenance section.
Maintenance Daily
maintenance Weekly maintenance Monthly maintenance
Clean the outside of the machine. X
Make sure the throttle trigger lock and the throttle function
correctly from a safety point of view. X
Check that the stop switch works correctly. X
Check that the cutting attachment does not rotate at idle. X
Clean the air filter. Replace if necessary. X
Check that the guard is undamaged and not cracked. Replace
the guard if it has been exposed to impact or is cracked. X
Check that the trimmer head is undamaged and not cracked.
Replace the trimmer head if necessary. X
Check that nuts and screws are tight. X
Check that there are no fuel leaks from the engine, tank or fuel
lines.X
Check the starter and starter cord. X
Check that the vibration damping elements are not damaged. X
Clean the outside of the spark plug. Remove it and check the
electrode gap. Adjust the gap to 0.5 mm (.020”), or replace the
spark plug. Check that the spark plug is fitted with a suppressor. X
Clean the machine’s cooling system. X
Clean or replace the spark arrestor screen on the muffler (only
applies to mufflers without a catalytic converter). X
Clean the outside of the carburettor and the space around it. X
Check the fuel filter from contamination and the fuel hose from
cracks or other defects.Replace if necessary. X
Check all cables and connections. X
Replace the spark plug.Check that the spark plug is fitted with a
suppressor.X