Huzzard CR1000 User manual

Using the CR1000 in a Universal Stand
Hardware Revisions 4+ of the CR1000s have a stand detecon
feature. By default, when the CR1000 is placed in the stand, the
reader will automacally enter into moon detecon mode.
When in this mode, simply place a bar code in the scan eld to
acvate the reader. The CR1000 will beep and ash a green LED
to indicate a ‘good read’ has occurred.
For USB Cable: plug the USB end of the Anity® cable into a USB port on the host device. Aer
several seconds, the reader will beep twice and the LED will turn o to indicate the CR1000 is
ready for use.
For RS232 Cable: plug the power supply into the AC outlet, plug the power supply cord into
the barrel jack of the cable, and connect the RS232 connector to the appropriate serial port on
the host device. Aer several seconds, the reader will beep twice, the reader will vibrate and
the LED will turn o to indicate the CR1000 is ready for use.
Using the CR1000 Out of a Universal Stand
Powering on the CR1000
The default seng on the CR1000 has Sux Enter disabled. To enable Sux Enter, please
scan the following conguraon code:
CR1000 Default Sengs
Aztec
Codabar
Code 39
Data Matrix Rectangle
All GS1 DataBar
Interleaved 2 of 5
Code 93
Code 128
Data Matrix
PDF417
QR Code
UPC/EAN/JAN
The CR1000, out of the box, will read the following bar codes:
To congure a CR1000 to read bar codes not listed, please download the CR1000
Conguraon Guide from www.codecorp.com and scan the appropriate ‘Enable’ bar code
reading symbology conguraon code.
Sux Enter Conguraon
Sux Enter - USB Carriage Return, Line Feed - RS232
For more conguraon opons, download the CR1000 Conguraon Guide from
www.codecorp.com.
Serial #: 20000XXXX
MFG #: CR1011_04
Designed in USA.
Made in Malaysia.
Determining the Hardware Revision of a CR1000
Locate the Serial Label on the reader to idenfy the hardware revision. CR1000 readers with
a MFG # of _04 (or higher) have the stand detecon mode.
_04 indicates
revision 4 hardware
2 3
Hardware Revisions 1-3 of the CR1000s do not have an automac stand detecon feature to
enable moon detecon reading when the CR1000 is in a stand. To congure these hardware
revisions for moon detecon scanning, please refer to the CR1000 Conguraon Guide,
located at www.codecorp.com and scan the appropriate code.
Press and hold the CR1000 trigger buon, the two blue bars
eming from the reader are used for targeng. Center the
blue bars in the middle of a bar code.
The opmal reading distance from reader to bar code is
approximately 4.0” (10 cm).
Once the reader is at the opmal distance, the CR1000 will read the bar code (when the
buon is pressed). The CR1000 will beep and ash a green LED to indicate a ‘good read’ has
occurred.
When the CR1000 is removed from the stand, the reader switches to manual mode and the
buon must be pressed to read a bar code.
www.codecorp.com www.codecorp.com

Quickstart Guide
C005747_06_CR1000_Quickstart_Guide
Code Reader™ 1000 (CR1000)
USB Anity® Cable RS232 Anity® Cable
w/ Power Supply
Aaching/Detaching a Cable
To aach a cable, plug the RJ-50 end of the Anity® cable into boom of the reader
(Figure 1). Firmly push the connector into the reader unl a snap can be heard, to
indicate the cable is properly aached. To detach a cable, press a paper clip into the
hole on the back of the CR1000 (Figure 2), and gently pull the cable from the reader.
Figure 2Figure 1
Included with your CR1000
Depending on the kit ordered, the following may have been shipped with your reader:
Universal Stand
Universal Stand Assembly (included when ordered as a Kit/Package)
Cleaning a CR1000
The following agents are approved to clean a Code bar code reader:
• Alcohol Wipes
• Clorox® Disinfecng Wipes
• Clorox® Bleach Soluon (10% Clorox bleach, 90% tap water)
• Medical DiAirKem
• Sani-Cloth® HB, Super Sani-Cloth® Germicidal, Sani-Cloth® Plus Germicidal
Disposable Wipes
• Virex® II Disinfectant Cleaner
© 2013. Code Corporaon. All Rights Reserved. 4