Hyco ZEN ZEN3LLT User manual

Zen
Boiling Water Tap
ZE 3LLT, ZE 3LHT,
ZE 3LLTP and ZE 3LHTP
Instruction Manual
Version 5.0 Dec 2014
ZEN_Layout 1 30/12/2014 09:06 Page 1

PLEASE READ THESE I STRUCTIO S BEFORE
COMME CI G I STALLATIO . UPO COMPLETIO
OF I STALLATIO E SURE THE I STRUCTIO S ARE
LEFT WITH THE USER/MAI TAI ER OF THE PRODUCT.
Zen Boiling Water Tap
MODELS ZE 3LLT, ZE 3LHT, ZE 3LLTP, ZE 3LHTP
1. I TRODUCTIO
Thank you for purchasing a Hyco Zen Boiling Water Tap. The Zen is a stylish,
modern, time and space saving addition to any kitchen replacing the need for
a traditional kettle, counter top or wall mounted boiling water unit.
Please note the Zen is a storage type heater - it cannot deliver a continuous
flow of hot water.
2
ZEN_Layout 1 30/12/2014 09:06 Page 2

2. IMPORTA T SAFETY POI TS
ALWAYS SWITCH OFF THE MAI S BEFORE COMME CI G
I STALLATIO .
O LY CO ECT THE HEATER TO A SI GLE PHASE SUPPLY WITH
A MAI S VOLTAGE AS SPECIFIED O THE RATI G LABEL.
THE SUPPLY CORD CA OT BE REPLACED BY THE USER. IF THE
CORD IS DAMAGED THE APPLIA CE SHOULD BE RETUR ED TO
THE MA UFACTURER OR A AUTHORISED SERVICE AGE T FOR
REPLACEME T.
THE HOSES A D PIPES SUPPLYI G THIS HEATER MUST OT COME I
CO TACT WITH A Y FIXED WIRI G OR THE SUPPLY CHORD.
DO OT CARRY THE APPLIA CE BY THE POWER CORD.
A RCD CIRCUIT BREAKER IS STRO GLY RECOMME DED.
THIS U IT DISPE SES BOILI G WATER.
THE TA K U IT MUST BE PLACED O A SOLID SURFACE WHERE IT
WILL OT BE K OCKED OVER CAUSI G DAMAGE TO THE WATER
HOSES OR ELECTRICAL CO ECTIO S.
THE HEATER MUST OT BE USED I A AREA SUBJECT TO FLAMMABLE
VAPOURS SUCH AS PAI T, SOLVE T OR PETROL.
THIS PRODUCT IS OT SUITABLE FOR OUTDOOR USE OR USE I
DAMP CO DITIO S.
DO OT USE I AMBIE T TEMPERATURES EXCEEDI G 30°C.
ALLOW 20MM SPACE AROU D THE TA K TO WALLS FOR COOLI G
AIR CIRCULATIO .
THE HEATER MUST BE FITTED WITH A RELIEF VALVE.
THE RELIEF VALVE MUST BE TESTED REGULARLY TO REMOVE SCALE
DEPOSITS.
3
ZEN_Layout 1 30/12/2014 09:06 Page 3

WATER MAY DRIP FROM THE PRESSURE RELIEF VALVE, THIS MUST BE
LEFT OPE TO ATMOSPHERE.
THIS APPLIA CE CA BE USED BY CHILDRE AGED 12 A D ABOVE
A D PERSO S WITH REDUCED PHYSICAL, SE SORY OR ME TAL
CAPABILITIES OR LACK OF EXPERIE CE A D K OWLEDGE IF THEY
HAVE BEE GIVE SUPERVISIO OR I STRUCTIO CO CER I G
THE USE OF THIS APPLIA CE I A SAFE WAY.
CHILDRE SHALL OT PLAY WITH THE APPLIA CE.
CHILDRE SHALL OT CLEA OR MAI TAI THE APPLIA CE
WITHOUT SUPERVISIO .
BEFORE CO DUCTI G A Y USER MAI TE A CE THE PRODUCT
SHOULD BE ISOLATED FOR THE ELECTRICAL SUPPLY A D THE OPE
THE TAP U TIL THE WATER RU S COLD.
DO OT MODIFY OR MISUSE THE PRODUCT I A Y WAY OR SERIOUS
I JURY COULD OCCUR.
4
ZEN_Layout 1 30/12/2014 09:06 Page 4

5
3. I STALLATIO OVERVEW
Figure 1 below shows the correct installation for models ZE 3LLT, ZE 3LHT,
ZE 3LLTP, ZE 3LHTP.
O LY USE THE SUPPLIED FITTI G, DO OT ATTEMPT TO MODIFY THE
PRODUCT I A Y WAY OR SERIOUS I JURY MAY RESULT.
COMPLETE THE PLUMBI G I STALLATIO BEFORE CO ECTI G
TO ELECTRICITY SUPPLY.
USE THE SUPPLIED EXPA SIO TA K, RELIEF VALVE, HOSES A D TAP.
ORDI ARY PARTS MAY OT TAKE THE HIGH TEMPERATURES WHICH
MAY CAUSE I JURY OR DAMAGE TO PROPERTY.
THE PIPE WORK TO THE RELIEF VALVE SHOULD BE MADE WITH 15MM
COPPER PIPE WITH SOLDERED JOI TS.
THE HOSES A D PIPES SUPPLYI G THIS HEATER MUST OT COME I
CO TACT WITH A Y FIXED WIRI G
THIS WATER HEATER MUST BE FITTED WITH A PRESSURE RELIEF VALVE.
WATER MAY DRIP FROM THE PRESSURE RELIEF VALVE, THIS MUST BE
LEFT OPE TO ATMOSPHERE (A TU DISH IS RECOMME DED) I A
FROST FREE E VIRO ME T.
Mains
To waste
To tank
inlet
White
washer
Black
washer
ZEN_Layout 1 30/12/2014 09:06 Page 5

4. PLUMBI G CO ECTIO S
Step 1 - Tank Positioning
Allow 20mm space around the tank to walls for cooling air circulation.
Position the tank vertically beneath the tap in a position such that the flexible hoses
can comfortably reach the tap and water supply.
E SURE THE FLEXIBLE HOSES DO OT TWIST OR KI K.
Step 2 - Tap Installation
Determine a convenient location to mount the tap. This can be an existing hole in the
sink top (if the sink is particularly thin the large black washer may be needed. The
washer should be placed on the underside of the sink.), or you may choose to drill
another hole (32mm diameter) either through the sink or the counter top.
The tap can be installed on to sink/counter top that is up to 50mm thick.
Place the tap into the hole ensuring the o ring is correctly seated in the
groove on the base of the tap.
While holding the base of the tap, tighten the clamping nut using a basin spanner.
This process is illustrated below.
6
ZEN_Layout 1 30/12/2014 09:06 Page 6

Step 3 - Connect Tap to Tank
Fit the outlet flexible hose to the connection protruding from the base of the tap
using the supplied washer (white). Be careful not to strip or loosen the ends of the
copper pipe in the base of the tap.
Connect the other ends of the flexible hoses to the back of the heater using the pro-
vided washers.
The lead from the tap connects into the back of the unit just above the inlet and out-
let hoses.
Step 4 Connect to Water S pply
This product must be fitted with a relief valve. Figure 1 shows the recommended
installation. The pipe work to the relief valve should be made with 15mm copper pipe
with soldered joints. Once the installation has been completed as shown in figure 1,
the water can be turned on. Open the tap until water flows from the tap. Close the
tap and check the installation for leaks.
5. ELECTRICAL CO ECTIO
REMI DER - DO OT PROCEED U LESS YOU ARE SURE THE TA K IS
FULL OF WATER. DAMAGE OR PERSO AL I JURY COULD OTHERWISE
RESULT.
Plug unit into 13A switched mains socket ensuring the supply chord does not come in
contact with the flexible hoses or pipe work.
7
ZEN_Layout 1 30/12/2014 09:07 Page 7

8
6.OPERATI G THE WATER HEATER A D TAP
THIS APPLIA CE CA BE USED BY CHILDRE AGED 12 A D ABOVE
A D PERSO S WITH REDUCED PHYSICAL, SE SORY OR ME TAL
CAPABILITIES OR LACK OF EXPERIE CE A D K OWLEDGE IF THEY
HAVE BEE GIVE SUPERVISIO OR I STRUCTIO CO CER I G THE
USE OF THIS APPLIA CE I A SAFE WAY.
The unit will power up and begin to heat as soon as the power is turned on.
The status ring on the base of the tap will light up red or green depending on the
temperature of the water in the tank. Red status ring means the water is heating up
and a green status ring means the water is up to temperature and is ready for use.
To open the tap slide the safety catch away from the tap and rotate handle of the tap.
If the status light begins to flash red this means the temperature controller has
detected a fault.
The unit should be isolated from the power supply and the water supply shut off.
For pattern recognition
models (ZE 3LLTP, ZE 3LHTP),
the status ring may be green
and fade on and off slowly,
this indicates the heater
is in a predicted none use
period. To exit this mode
open the tap and allow
water to flow until the
status ring flashes green.
Then the heater will
recover back to boiling
shortly after.
Status ring
Safety catch
Handle
ZEN_Layout 1 30/12/2014 09:07 Page 8

7. DRAI I G
THE U IT MUST BE DRAI ED IF IT MAY BE EXPOSED TO FREEZI G
TEMPERATURES.
To drain:
• Disconnect from the electricity supply by unplugging the heater
• Open the tap until the water runs cold
• Isolate the water supply
• Disconnect the water pipes from the supply and tap.
• Unplug the tap connector lead from the back of the heater
• Pour the water out of the tank over a bucket or sink
• Turn the unit upside down and allow the water to flow out of the tap hose until
the flow stops.
To reassemble the heater, follow the installation instructions.
DO OT CO ECT TO ELECTRICITY SUPPLY WITHOUT RE-FILLI G
TA K AS PER SECTIO 4.
8. MAI TE A CE
BEFORE CO DUCTI G A Y USER MAI TE A CE THE PRODUCT
SHOULD BE ISOLATED FROM THE ELECTRICAL SUPPLY A D THE
OPE THE TAP U TIL THE WATER RU S COLD.
THE RELIEVE VALVE MUST BE REGULARLY TESTED, TO DO THIS TWIST
THE RED CAP U TIL WATER FLOWS FROM THE VALVE. IF THE VALVE IS
SCALED UP IT MUST BE REPLACED.
THE SUPPLY CORD CA OT BE REPLACED BY THE USER. IF THE
CORD IS DAMAGED THE APPLIA CE SHOULD BE RETUR ED TO
THE MA UFACTURER OR A AUTHORISED SERVICE AGE T FOR
REPLACEME T.
CHILDRE SHALL OT CLEA OR MAI TAI THE APPLIA CE WITH
OUT SUPERVISIO .
The tap and water tank can be cleaned with a lint free damp cloth. Do not use any
abrasive or caustic cleaning products as this will damage the surface of the product.
9
ZEN_Layout 1 30/12/2014 09:07 Page 9

10
9. SPECIFICATIO S
Model ZE 3LLT, ZE 3LHT, ZE 3LLTP, ZE 3LHTP
Power 1550W
Voltage 230V 50Hz ac
Dimensions (h x w x d) tank 459mm x 220mm x 181mm
Max supply pressure 1MPa
(before pressure reducing valve)
Max supply pressure 0.3MPa
(after pressure reducing valve)
Min supply pressure 0.1MPa
Maximum tank pressure 0.6MPa
Capacity 3L
Ambient operating temperature 5-300C
ZEN_Layout 1 30/12/2014 09:07 Page 10

10. GUARA TEE A D SERVICE POLICY
This product is guaranteed against faulty materials and manufacture for a period of
one year from the date of purchase. Hyco will in its sole discretion replace, repair
or refund any faulty unit. Incorrect installation, frost damage, and the consequences
of limescale deposits are excluded. Consequential costs such as labour charges or
damage to fittings and surroundings are expressly excluded.
11
ZEN_Layout 1 30/12/2014 09:07 Page 11

Hyco Man fact ring Ltd
ormandy Court, Express Way
Castleford, WF10 5 R
Sales: 01924 225 200
Fax: [phone]
Switchboard: 01924 225 215
Email: [e-mail]
www.hyco.co.uk
WATER HEATING SPACE HEATING HAND DRYERS
I FORMATIO FOR CORRECT DISPOSAL OF THE PRODUCT I
ACCORDA CE WITH THE EUROPEA DIRECTIVE 2002/96/E.
At the end of its working life this equipment must not be disposed of as
household waste. It must be taken to a local authority waste collection centre
or to a dealer providing this service. Disposing of electrical and electronic
equipment separately enables its components to be recovered and recycled to
obtain significant savings in energy and resources. In order to underline the
duty to dispose of this equipment separately, the product is marked with a
crossed out dustbin.
ZEN_Layout 1 30/12/2014 09:07 Page 12