HydraMaster Titan H2O Kubota User manual

Titan H2O Kubota
Owner’s Manual
HydraMaster
11015 47th Avenue West
Mukilteo, Washington 98275
MAN-44359 Rev. 0, April 13, 2012
(182-860-D)
No part of this manual may be reproduced or used in any form or by any means (i.e. graphic, electronic, photocopying or electronic
retrieval systems) without the express written permission of HydraMaster. Specications and information in this document are
subject to change without prior notice. All rights reserved. © 2012 HydraMaster

i - Titan H2O Owner’s Manual
Table of Contents
GENERAL INFORMATION...........................................................................SECTION 1
Contact Information................................................................................. 1-4
Warnings, Cautions and Notices.............................................................1-5
Responsibilities....................................................................................... 1-8
Machine Specications ........................................................................... 1-11
Optional Equipment.................................................................................1-12
Spare Parts............................................................................................. 1-13
High Altitude Operation...........................................................................1-13
Waste Water DisposalAdvisory..............................................................1-14
INSTALLATION INFORMATION...................................................................SECTION 2
Operating the Titan H2O In Hot Weather.................................................2-1
Locating the Titan H2O In Vehicle............................................................2-2
Setting Up the Titan H2O.........................................................................2-3
Orientation of Fuel Pump........................................................................ 2-4
OPERATING INSTRUCTIONS.....................................................................SECTION 3
Start Up Procedure ................................................................................. 3-2
Shut Down Procedure.............................................................................3-2
MACHINE MAINTENANCE.......................................................................... SECTION 4
Operational Maintenance........................................................................4-2
Overall Machine Maintenance.................................................................4-3
Engine Maintenance ...............................................................................4-4
Vacuum System Maintenance ................................................................ 4-7
ELECTRICAL SYSTEM................................................................................SECTION 5
Electrical System Information..................................................................5-1
SYSTEMS TROUBLESHOOTING...............................................................SECTION 6
Engine.....................................................................................................6-1
Vacuum System......................................................................................6-4

Titan H2O Owner’s Manual - ii
ASSEMBLIES AND PARTS LIST.................................................................SECTION 7
Machine Assembly Parts List..................................................................7-6
Frame Assembly Parts List .....................................................................7-8
Top Cover Assembly Parts List ...............................................................7-9
Side Cover Assembly Parts List.............................................................. 7-10
Engine Assembly Parts List..................................................................... 7-14
Blower and Silencer Assembly Parts List................................................7-16
Exhaust Assembly Parts List...................................................................7-18
Flywheel Plate Assembly Parts List ........................................................7-20
Upper Dash Assembly Parts List............................................................. 7-22
Lower Dash Assembly Parts List............................................................. 7-23
Grill Assembly Parts List .........................................................................7-24
Electrical Panel Assembly Parts List....................................................... 7-27
100 Gallon Universal Recovery Tank (URT) Assembly Parts List........... 7-29
100 Gallon Universal Recovery Tank (URT) Cover Assembly Parts List 7-31
Vacuum Relief Valve Assembly Parts List...............................................7-32
HOW TO ORDER PARTS............................................................................SECTION 8
Warranty Parts Orders ............................................................................ 8-1
Parts Orders............................................................................................ 8-1
Emergencies........................................................................................... 8-1
WARRANTY INFORMATION.......................................................................SECTION 9
Blower..................................................................................................... 9-1
Vacuum Tank...........................................................................................9-1
Vacuum Hoses........................................................................................ 9-1
Recovery Wand ......................................................................................9-1
Golden Guarantee ..................................................................................9-1

iii - Titan H2O Owner’s Manual
List of Figures
Figure 1-1. Illustration Showing Left and Right Views
of Titan H2O without Side and Belt Covers...............................................1-3
Figure 2-1. Location of Roof Vents in Vehicle .............................................................2-1
Figure 2-2. Recommended Location of Titan H2O in Van............................................2-2
Figure 2-3. Install Fuel Pump, Outlet Side Up.............................................................2-4
Figure 2-4. Fuel Pump Must Be in Vertical Position....................................................2-4
Figure 3-1. Titan H2O Front Panel Assembly...............................................................3-1
Figure 5-1. Electrical Schematic .................................................................................5-2
Figure 5-2. Wiring Diagram - View 1 of 3 ...................................................................5-3
Figure 5-3. Wiring Diagram - View 2 of 3 ...................................................................5-4
Figure 5-4. Wiring Diagram - View 3 of 3 ...................................................................5-5
Figure 7-1. Machine Assembly - View 1 of 4...............................................................7-2
Figure 7-2. Machine Assembly - View 2 of 4...............................................................7-3
Figure 7-3. Machine Assembly - View 3 of 4...............................................................7-4
Figure 7-4. Machine Assembly - View 4 of 4...............................................................7-5
Figure 7-5. Frame Assembly .......................................................................................7-7
Figure 7-6. Top CoverAssembly ................................................................................7-9
Figure 7-7. Side Cover Assembly .............................................................................7-10
Figure 7-8. Engine Assembly - View 1 of 3................................................................7-11
Figure 7-9. Engine Assembly - View 2 of 3 ...............................................................7-12
Figure 7-10. Engine Assembly - View 3 of 3 .............................................................7-13
Figure 7-11. Blower and Silencer Assembly .............................................................7-15
Figure 7-12. Exhaust Assembly ................................................................................7-17
Figure 7-13. Flywheel Plate Assembly .....................................................................7-19
Figure 7-14. Upper Dash Assembly- View 1 of 2 ......................................................7-21
Figure 7-15. Upper Dash Assembly - View 2 of 2......................................................7-22
Figure 7-16. Lower Dash Assembly ..........................................................................7-23
Figure 7-17. Grill Assembly ......................................................................................7-24
Figure 7-18. Electrical Panel Assembly - View 1 of 2................................................7-25
Figure 7-19. Electrical Panel Assembly - View 2 of 2................................................7-26
Figure 7-20. 100 Gallon Universal Recovery Tank (URT) Assembly.........................7-28
Figure 7-21. 100 Gallon Universal Recovery Tank (URT) Cover Assembly..............7-30
Figure 7-22. Vacuum Relief Valve Assembly ............................................................7-32

Titan H2O Owner’s Manual - iv

1-1: General Information
HydraMaster’s Titan H2O Water Recovery System has been designed to better
accommodate the needs of water extraction, recovery and restoration professionals.
The Titan H2O features a WG 972 Kubota engine that powers a Tuthill 4007 Tri-Lobe
vacuum blower. This combination produces over 400 cfm of air ow, more than enough
to extract water with one or two wands
(or other extraction tools).
HydraMaster’s reliable Dura-Flow
Automatic Pump Out (APO), offered as
an option, allows you to extract water
without the need to shut down and
dispose of the recovered water.
Other features of the Titan H2O include:
Dual oil bath and sight glasses for
• enhanced blower reliability
Dual tool/wand capable
•
In addition to the obvious performance
aspects of the Titan H2O, it delivers
maximum reliability and can be
easily serviced. All service points
are conveniently located so routine
maintenance takes only a few minutes
to perform.
HydraMaster suggests that the operator
of the machine be well acquainted with
the IICRC guidelines for Flood Extraction and with the various methods of carpet and
surface drying that are currently being used. It is also recommended that the machine
operator be familiar with the local municipality’s requirements for the proper disposal of
waste water.
As with any machine, it is important to use the Titan H2O correctly. Operating the machine
is simple as described in Section 3 of this Owner’s Manual. This manual also contains
installation as well as information required for proper maintenance, adjustment and
repair of the Titan H2O. Component troubleshooting guides have been included for your
convenience.
1- General Information

General Information: 1-2
It is the purpose of this manual to help you properly understand, maintain and service
your Titan H2O. Follow the directions carefully and you will be rewarded with years of
protable, trouble-free operation.
No section of this manual should be overlooked when preparing for operation of the
Titan H2O. Please read the manual to familiarize yourself with the operation of your
machine, paying special attention to all Warnings and Cautions.
This section of the manual contains the following information:
Contact Information

Warnings, Cautions and Notices

Responsibilities

Machine Specications

High Altitude Operation

Waste Water DisposalAdvisory


1-3: General Information
Photographs and illustrations, such as those included in this document, can
represent optional equipment as well as standard equipment.
Illustration Showing Left and Right ViewsFigure 1-1.
of Titan H2O without Side and Belt Covers
Silencer
Engine
Vacuum Blower

General Information: 1-4
CONTACT INFORMATION
If you have any questions regarding the operation, maintenance or repair of this machine,
please contact your local distributor.
To nd a local distributor, please visit our website at:
http://hydramaster.com/HowToBuy/DealerLocator.aspx
If your question cannot be resolved by your distributor or by the information within this
manual, you may contact HydraMaster direct using the following phone numbers.
HOURS TELEPHONE NUMBERS E-MAIL ADDRESSES
Monday-Friday
7:00 a.m. to 5:00 p.m.
Pacic Standard Time
Technical Support
[phone]
FAX : [phone]
Technical Support
[e-mail]
Customer Service/Parts
[phone]
FAX: [phone]
Customer Service/Parts
[e-mail]
When calling your distributor, be sure to reference the serial number and date of
purchase.
FOR YOUR REFERENCE:
Serial No.____________________________________________________
Date of Purchase:_____________________________________________
Purchased From (Distributor): __________________________________

1-5: General Information
WARNINGS, CAUTIONS AND NOTICES
HydraMaster uses this WARNING symbol throughout the manual to warn of
possible injury or death.
This CAUTION symbol is used to warn of possible equipment damage.
This NOTICE symbol indicates that federal or state regulatory laws may apply,
and also emphasizes supplemental information.

General Information: 1-6
Warnings and Cautions specic to the Titan H2O include the following:
During the operation of the truckmount many components are in motion. Never
touch any part of the truckmount that is in motion. Serious injury may result.
During the operation of the truckmount many surfaces will become extremely hot.
Never touch hot surfaces. Serious injury may result.
The operation of this truckmount can produce noise levels exceeding 85 decibels
to a distance of 10 ft (3.05 m). The Occupational Safety and HealthAdministration
(OSHA) recommends the use of hearing protective equipment if a person is
exposed to an average of 85 decibels over an 8-hour period. Check with local
and state agencies concerning hearing conservation rules.
During the operation of the truckmount carbon monoxide and other toxic fumes
are produced. Position the vehicle so that any fumes produced will be directed
away from inhabited areas and any points of building entry (doors, windows, air
conditioning units, fans, etc.). Do not occupy the vehicle while the truckmount is
in operation. Serious injury may result.
Duringtheoperation of the truckmount, chemicals knownto the State of California
to cause cancer, birth defects and other reproductive harm are produced by the
engine exhaust.
Never operate the truckmount with a portable gas container inside the vehicle.
Doing so will increase the risk of re and explosion. Serious injury or death may
result.
Transportingaventedfuelcontainerthatpresentlycontains,orhasevercontained
in the past, a ammable liquid is strictly forbidden by HydraMaster and by federal
and state regulations. Doing so will increase the risk of re and explosion. Serious
injury or death may result.

1-7: General Information
Never smoke in or around the truckmount. Doing so will increase the risk of re
and explosion. Serious injury or death may result.
During the operation of the truckmount the exhaust system will become extremely
hot. Keep all ammable materials away from the truckmount exhaust system.
Failure to do so will increase the risk of re and explosion. Serious property
damage may result.
Never operate the truckmount when the vehicle is tilted more than 10 degrees in
anydirection.Doingsowillresultinimproperlubricationoftheinternalcomponents,
and will increase the risk of serious component or engine damage.
Never operate the truckmount with the vehicle doors closed. Doing so results in
extremelyhigh temperatures inside thevehicleandwilllead to serious component
or engine damage.
Many vehicles have critical components mounted directly below the oor that
can easily be damaged. Before drilling holes in the oor of the vehicle inspect
the underside of the vehicle for critical components. Failure to do so may result
in damage to the vehicle.

General Information: 1-8
RESPONSIBILITIES
Purchaser’s Responsibilities
Prior to purchasing a van, ensure that the payload is suitable for all of the equipment• thatwillbeinstalledandtransported.Thisincludesandisnotlimitedto:thetruckmount,
recovery tanks, hose reels, hoses, tools and drying equipment. Payload capacity
information is available through the auto dealer, the manufacturer’s web site, and is
also located on the door pillar of the driver’s side door.
Purchase a heavy duty Group 24 (500+ CC Amps) battery for this truckmount. This is• normally available from the installation dealer.
Prior to dropping your van off at the distributor for the truckmount to be installed, have•
aspray-onbedlinerappliedtotheoorsuchasRhinoLining®orLine-X®.
Plywood and carpet are not recommended.
Prior to operating the truckmount, read this manual in its entirety and familiarize• yourself with the information contained here. Special attention should be paid to all
Warnings and Cautions.
The distributor is responsible for the correct installation of the truckmount. The• distributor is also responsible to train you in the correct and proper operation and
maintenance of the truckmount.
Anymodicationofthetruckmountmayvoidthewarranty.

1-9: General Information
Distributor’s Responsibility
Acceptance of Shipment
Before accepting the truckmount, check the following:
The truckmount should be free from any damage during shipping. Do not sign the1. delivery receipt until you have closely inspected the truckmount and noted any
damageonthedeliveryreceipt.Hiddendamagemaybepresenteveniftheboxlooks
okay. It is recommended that the box be opened before you sign for the shipment.
Check the packing list and verify that all items are present.
2.
Installation Responsibilities
Ensure proper payload capacity. It is the distributor’s responsibility to verify that the• equipment package does not exceed the vehicle capacity.
Ensure installation of a safe fuel tap system and through-oor ttings as provided by
• HydraMaster.
Ensure proper placement of the truckmount, recovery tank and accessories in the• vehicle, and check that they are secured with bolts and back up plates. The distributor
should verify that the owner is in agreement with the layout.
Ensure proper connection of the fuel lines.• Ensure proper connection and installation of the battery. Verify that the battery is in• accordance with HydraMaster’s recommendation.
Check the vacuum blower and engine oil levels prior to starting the truckmount.
• Start and run the truckmount and check that all systems function properly.• Test all hoses, wands and other accessories for correct operation.• Ensure timely return of the document package.•

General Information: 1-10
Training
The distributor should provide a thorough review of the operation manual with the
purchaser along with instruction and familiarization in:
How all the truckmount’s systems function.
1. All safety precautions and their importance.2. How to correctly start and shut down the truckmount.3. How to correctly operate the truckmount.4. Where and how often to check and change component oil levels.5. How to do basic troubleshooting of the truckmount.6. The truckmount’s warranty and warranty procedures.7.

1-11: General Information
MACHINE SPECIFICATIONS
Frame Dimensions 26.0" W x 45" D x 39" H
(66 cm x 114 cm x 99 cm)
Weight 775 lbs (352 kg)
Engine - Kubota Oil Type 5W-30 Synthetic
Capacity 3.2 quarts (3.02 litres)
when changing oil and lter
Engine rpm High - 3,000 rpm
Idle - 1,500 rpm
Fuel Consumption 1.78 gph (6.74 litres/hr)
Ignition Keyless
Vacuum Blower - Tuthill
4007 Competitor (Dual
Splash Lubrication)
Oil Type
Max. Vac. 14” Hg PneuLube or other ISO 100 rating
Gear End Capacity Approx. 5.8 oz. (171.5 ml)
Drive End Capacity Approx. 4.7 oz. (139 ml)
Blower rpm 3,000 rpm
Standard Equipment Vacuum Hose 2" Vacuum Hose - 100 ft.
(5.08 cm Vacuum Hose -
30.5 m)
Recovery Hose 10 ft (3.05 m)
Recovery Tank 100 gallon Universal Tank
(379 litre Universal Tank)
Battery Box
Van Decal
Van Installation Kit
Owner’s Manual (on CD)
Owner’s Guide (printed)

General Information: 1-12
OPTIONAL EQUIPMENT
To better meet your business needs, HydraMaster offers several options that you can
add to your basic Titan H2O system. The following shows the available options and the
additional kits necessary to install the options. Refer to the following table before placing
your order for optional equipment.
If you want this option: Order this P/N:
2.5” Vacuum Hose Adapter (100
Gallon Recovery Tank) 000-078-875 Kit, 2.5” 3 Port Hose and 000-041-466, Cover Assembly
Automatic Pump Out (APO) 000-079-091 Pump, Dura-Flow APO
Exhaust Thru Floor 000-078-414 Exhaust Thru Floor Kit
If you have questions or need assistance conguring your system, please contact your
distributor.

1-13: General Information
SPARE PARTS
The following table is a list of available Titan H2O spares that distributors may purchase
to have on hand for repairs and maintenance.
Part No Description Qty
000-010-131 Belt, 3vx450 Eng. Drive 3
000-025-003 Cable, Choke, With Detent 1
000-049-002 Filter, Fuel 1
000-049-063 Filter, Air - Kubota 1
000-049-256 Filter, Oil - Kubota 1
000-049-152 Filter, Basket, Recovery Tank 1
000-049-153 Filter, Stainless Steel Vacuum Pump 1
000-056-011 Fuse, 30 Amp Circuit 2
000-057-177 Gasket, Exhaust Doughnut 1
000-073-011 Impeller, Replacement, APO 1
000-074-025 Gauge, Vacuum 0-30” Hg 1
000-087-006 HydraMaster-recommended Lubricant Blower Spray - part
number is for 1 can 1 ea
000-157-022 Switch, Relay 1
000-157-040 Switch, 12V DC, On/Off 1
000-157-131 Switch, 12V DC, Throttle 2
000-157-152 Switch, Ignition, 3-Way 1
000-169-022 Valve, 1 1/2" Full Port 1
HIGH ALTITUDE OPERATION
Elevation plays a key role in how the truckmount will operate. Operation at high altitude
(above 5,000 ft [1,524 m]) may require a high-altitude carburetor jet. Use of this jet at high
altitude will improve power, reduce fuel consumption and help reduce excessive carbon
build-up in the exhaust system.
Contact the local Kubota dealer or HydraMaster to obtain the proper jet size. Find your
local Kubota dealer at http://www.kubotaengine.com/distributor/engine_usa.html.

General Information: 1-14
WASTE WATER DISPOSAL ADVISORY
There are laws in most communities prohibiting the dumping of recovered “gray” water
from carpet cleaning in any place but a sanitary treatment system.
The cleaning rinse water, recovered into your unit’s vacuum tank, contains materials
such as detergents, and must be safely processed before entering streams, rivers and
reservoirs.
In most cases, an acceptable method of waste water disposal is to discharge into a
municipal sewage treatment system after rst ltering out solid material such as carpet
ber. Access to the sanitary system can be obtained through a toilet, laundry drain, RV
dump, etc. Permission should rst be obtained from any concerned party or agency.
One disposal method which usually complies with the law is to accumulate the waste
water and haul it to an appropriate dump site. Another solution to the disposal problem is
to equip your Titan H2O with an Automatic Pump-Out System (APO). These systems are
designed to remove waste water from the extractor’s recovery system and actively pump
the water through hoses to a suitable disposal drain.
HydraMaster makes an APO System which can be ordered with new equipment or
installed later.
When properly congured, the systems will continuously monitor the level of waste water
and pump it out simultaneously with the cleaning operation. The hidden benet of this
process is that the technician does not have to stop his/her cleaning to empty the recovery
tank.
INACCORDANCEWITHEPA,STATEANDLOCALLAWS,DONOTDISPOSEOF
WASTE WATERINTOGUTTERS,STORMDRAINS, STREAMS,RESERVOIRS,
ETC.
The penalties for non-compliance can be serious. Always check local laws and
regulations to be sure you are in compliance.