Hydrostress VCE2000U Series User manual

Operating manual
Spare parts list
Wet/Dry Vacuum Cleaner
VCE2000U
Index / Indice “003”
10987401 en / 01.12.2008

Manufacturer’s address:
TYROLIT Hydrostress AG
Witzbergstrasse 18
CH-8330 Pfäfkon
Switzerland
Tel. [phone]
Fax [phone]
e-mail: [email protected]
www.hydrostress.com
TYROLIT Hydrostress AG reserves the right to make technical changes without
prior notice.
Copyright © 2006 TYROLIT Hydrostress AG, CH-8330 Pfäfkon ZH, Switzerland
All rights reserved, in particular copyrighting and translating rights.
Printing of this operating manual, including extracts from it, is prohibited. No
parts of it may be reproduced in any form or processed using electronic sys-
tems, duplicated or disseminated without the written permission of TYROLIT
Hydrostress AG.

1
Caution May cause death or serious injury.
Notice May cause injury if operated improperly.
This symbol indicates actions
that are prohibited.
This symbol indicates useful in-
structions that must be followed.
Symbol
Legend
Safety Rules
CAUTION
1
For your safety and to ensure accident-free operation please carefully read and
understand these “Safety Rules”.
After reading these instructions, please keep the manual in a obvious place for reference.
1
Only a qualied technician may
disassemble, repair or recon-
struct this machine.
Do not wipe or pour oil or water
into the machine. Moisture
entering the product will cause
electric shock or short circuit.
Please disconnect the power
source before cleaning or
performing a safety check to
prevent electric shock or injury.
Never use a damaged power
plug. Doing so may cause an
electric shock, short circuit or
re.
Please do not use the machine
to pick up the following materials
to avoid re, explosion or injury.
* Explosive powder: Aluminum (AI)
Magnesium (Mg), Titanium (Ti), Zinc
(Zn), etc.
* Flammable material: Gasoline,
organic solvent, benzene, lamp-oil,
paint, etc; Chemical material: Oil,
medicine, etc.
* Hot material: Campre ashes,
cigarette butt, etc; Powder accompa-
nied by sparks: High-speed cutting
machine, grinding wheel, welding
machine, etc.
Never operate the product near
explosive or ammable materi-
als such as lamp oil, gasoline,
organic solvent, benzene and
paint to avoid re, explosion or
injury.
Keep children away from the
product to avoid injury.

2
NOTICE
Do not use the machine in a high tem-
perature enviroment.
Install lters before using the machine.
Otherwise, the motor may be damaged.
Unplug the machine when idle to
prevent electric leakage, electric shock
and re.
Turn off the power and disconnect the
plug during installation and mainte-
nance to avoid electric shock and injury.
Stop operation when the inlet and ex-
haust holes are blocked. Otherwise the
machine will deform due to overheating.
When picking up dust, be sure to install
the polyester lter. Otherwise, the dust
entering the motor will damage the
motor.
Picking up too much dust will block the
lter causing damage to the motor due
to overheating.
When operating the machine in a dry
environment (especially during winter),
static electricity buildup may occur.
During normal operation, hot air will
be expelled from the cooling system
located at the top of the machine.
The lifetime of the ltration system
depends on the frequency and condition
of use. On average, the lifetime of the
lter is one year when operated in dry
conditions and half year when operated
in wet conditions. Please change the
lter regularly.
Do not touch the plug, power cable or
other electrical components with wet
hands to prevent electric shock.
Do not bend or pull the plastic tube. Do
not trample on the tube or place heavy
objects on it.
Do not bend or trample on the power
cable. Refrain from tugging the cable
as well.
Do not pull the power cable to remove
the plug from the outlet. Doing so may
cause a re as a result of a short circuit.
Empty the tank when bubbles or water
drops spurt from the exhaust outlet.
Run the machine without load to com-
pletely dry the lter.
Do not leave sewage and debris in the
tank for a prolonged period of time to
prevent the buildup of foul smell.
Use a power supply that does not ex-
ceed the normal voltage of 110V±10%
or 230V±10%, depending on model.
Maintain the same input voltage when
using the machine with a generator to
avoid electric shock, short circuit and
re.
Keep the machine away from re and
heat to reduce the risk of re and short
circuit.
Do not use the machine in a high
temperature enviroment. Doing so may
damage the machine and cause electric
shock and re. Please use this machine
under 80% humidity.
When starting the machine, use a
single motor to avoid drawing too much
current. If desired, dual motors may be
engaged after the machine has started.

A
B
C
To safely use the wet/dry vacuum cleaner, please pay attention to the following guide-
lines in addition to the safety rules discussed earlier.
Additional Safety
Rules
Please beware that picking up iron
powder or dust with the machine may
generate static electricity. If this occurs,
stop the machine immediately and keep
it away from precision instruments or
machines to avoid damaging them.
* The application of anti-static tape
is recommended on plastic handheld
components to prevent static discharge.
Do not use the machine on the same
electrical circuit used by sensitive
electronic devices. Voltage spikes
caused by turning the machine on
and off may damage those devices. If
an isolated circuit is not available, be
sure to turn off all sensitive electronic
devices that share the same circuit as
the machine.
When using the machine please keep
away from fragile or valuable objects
to avoid damaging them. The machine
is intended for industrial cleaning
purpose only.
3
iron powder or dust
2

4
Never operate the machine without
the polyester lter in place. The lter
prevents dust from entering the motor
and damaging it. When the machine
is running please do not block the
exhaust outlet.
Avoid twisting, bending, trampling or
forcefully pulling the hose. Any of
these activities, whether performed
during use or storage, will deform and
damage the hose.
After cleaning the tank, be sure to
empty it to prevent the buildup of foul
smell, mold and rust.
D
E
F
D
G
Never operate the machine without
the polyester lter in place. The lter
prevents dust from entering the motor
and damaging it. When the machine
is running please do not block the
exhaust outlet.
Dry mode
Wet mode

Parts
3
Motor head unit
Polyester lter
Filter retaining clip
Cloth lter frame
Accessories bag
Cloth lter
Cart
Extension wand
L-pipe
Squeegee Narrow nozzle
Wide nozzle Round brush
Hose adapter
Tank
Hose
5
Replacing Brush
Tank Gasket

5.
6.
7.
When emptying
the tank, dispose
of dust and debris
in accordance
with all applicable
regulations.
Reverse the
steps to install the
head unit back
onto the tank.
Removing Sewage
and Debris
Functions and Cleaning
Procedure
For cleaning carpets, rugs, car interiors, spills and much, much more.
*Use a wet cloth to clean the exterior of the machine. Never use water to directly wash the machine or the motor.
*Ensure that the machine is dry before use.
*When the tank is completely lled with liquid, an internal oat will obstruct the air ow. Once this occurs, imme-
diately turn off the machine and dispose of the sewage and debris stored within. Continued use of the machine
without proper air ow (i.e. without rst emptying the tank) may cause the motor to overheat and consequently
damage it.
Troubleshooting and
Maintenance
Routinely check the machine for parts
(e.g. hose, lter, etc) that will need to be
replaced. Replace them as needed.
Maintenance and Lubrication:
1. The motor bearings do not require any lubrication.
2. Lubricate the wheels on the cart as needed with 1-2
drops of grease.
PROBLEM CHECK SUGGESTION
Motor does
not work
Insufcient
suction to
pick up mate-
rials
Carbon brush
Temperature
Control
Hose
Tank contents
Filter
The plug may be loose. Connect the plug rmly with the power outlet.
If the carbon brush has been depleted, please contact our customer service.
The motor is protected by a thermal sensor that will shut off the motor when tempera-
tures exceed a predetermined threshold. The motor will resume operation after 10
minutes of rest.
If the hose or extension wands were not properly tted, reattach them to ensure a rm
t.
If the tank is full, empty it.
4
4
5
6
Plug
Please turn off and
unplug the machine
before releasing the
side clips.
Remove the head unit
and store it properly to
prevent any damage
and contamination.
Before removing
the cloth lter from
the tank, shake
the lter to loosen
any debris clinging
to the lter.
Notice
44
Check and clean the lters.

How To Use
Insert the lter into the tank and ensure that
it is seated properly.
Insert the lter frame, but make sure that it
does not obstruct the vacuum inlet.
Place the motor head unit onto the tank,
while ensuring that the attached lter is
seated within the lter frame.
Secure the head unit to the tank with the
clips provided on the tank.
1
2
3
4
Insert the black hose
into the receptacle
in front of the tank.
Make sure that it is
rmly attached.
1 2
3Press switch to ON to turn on the machine; or press switch to
OFF to turn off the machine.
Press switch to SINGLE to use a single motor for suction;
or press switch to DUAL to use both motors for suction. It is
recommended that only a single motor be used when starting
the machine.
Turn the knob to continuously adjust the suction power of the
motor(s). The inner gauge shows power levels while operat-
ing one motor and the outer gauge shows power levels while
operating two motors.
Attach the provided power cable into the receptacle. Plug the
other end of the cable into a suitable power source.
Power switch:
Motor switch:
Power adjustment knob:
Power receptacle:
7
A
B
C
D
7
ABCD
OFF
POWER
ON
ON
OFF
MOTOR
SINGLE
M
a
x
M
i
n
M
a
x
M
i
n
V
A
R
I
A
B
L
E
P
O
W
E
R
A
D
J
U
S
T
M
E
N
T
MODEL
ARTICLE NO.
POWER
SERIAL
AMP
MAX VACUUM
AIR FLOW
TANK CAPACITY
POWER
DUAL
7
4
•
123

Technical data
8
Article No.
Voltage
Mains Frequency
Power Consumption
Max Air Flow Volume
Max Negative
Pressure
Operating Noise
Power Cord Length
Tank Volume
Width
Depth
Height
Weight
Suction Hose Diameter
10983924
110 V
60 Hz
1000 W - one motor
2000 W - two motors
2300 l/min - one motor
4600 I/min - two motors
21000 Pa
75 dB(A) - one motor
80 dB(A) - two motors
7 m
80 L
575 mm
595 mm
935 mm
30.5 kg
38 mm inner diameter
48 mm outer diameter
10983921
230 V
50 Hz
1000 W - one motor
2000 W - two motors
2300 l/min - one motor
4600 I/min - two motors
21000 Pa
75 dB(A) - one motor
80 dB(A) - two motors
7 m
80 L
575 mm
595 mm
935 mm
30.5 kg
38 mm inner diameter
48 mm outer diameter
Specication
8

9
Wiring Diagram
9

10
Parts List
10
Pos SAP Part No Description Qty
1 10985340 EOSM-481001 1/4”-20x3/8” Phil. Screw 4
2 10985342 EOSM-481002 Black Accessories Basket 1
3 10985343 EOSM-481003 Upper Cover 1
4 10985344 EOSM-481004 PCB 1
5 10985345 EOSM-481005 Spacer RS-5 4
6 10985346 EOSM-481006 Hex Screw M8 X 1.25 X 5L 4
7 10985347 EOSM-481007 M6 (6x16x1.0) Washer 8
8 10985348 EOSM-481008 1/4”- 20 Nut 4
9 10985352 EOSM-481009 ON/OFF Power Switch 608FA 1
10 10985353 EOSM-481010 Single/Dual Motor Switch 1
11 10985354 EOSM-481011 M5 X 0.8 X 10L Screws 2
12 10985355 EOSM-481012 Air Exhaust Outlet 1
13 10985348 EOSM-481008 1/4”- 20 Nut 4
14 10985347 EOSM-481007 M6 (6x16x1.0) Washer 4
15 10985351 EOSM-481013 Lower Cover 1
16 10985356 EOSM-481014 R-301SN-M Receptacal Plug 1
17 10985357 EOSM-481015 Motor Power Adj. Switch 1
18 10985358 EOSM-481016 Power Adj. Switch Knob 1
19 10985359 EOSM-481017 Exhaust Air Guide Tube 1
20 10985362 EOSM-481018 Ø12 X 84L Spacer Tube 4
21 10985360 EOSM-481019 M5 X 0.8 Nut 1
22 10985361 EOSM-481020 M5 (5x10x1.0) Washer 1
23 10985363 EOSM-481021 Motor Cover 1
24 10985364 EOSM-481022 15G Rubber Ring 2
25 10985365 EOSM-481023 Sponge Ring Seal 2
26 10985366 EOSM-481024 Motor Housing 2
27 10985367 EOSM-481025 1000W 230V Motor 2
27 10985368 EOSM-481026 1000W 110V Motor 2
28 10985369 EOSM-481027 Motor Ground Connector 2
29 10985370 EOSM-481028 M4 X 0.7 X 8L Screw 2
30 10985371 EOSM-481029 Sponge Ring Seal 2
31 10985372 EOSM-481030 Wire Screen 2
32 10985364 EOSM-481022 15G Rubber Ring 2
33 10985373 EOSM-481031 BH 1/4*1 4
34 10985347 EOSM-481007 M6 (6x16x1.0) Washer 4
35 10985374 EOSM-481032 Valve Cap 1
36 10985375 EOSM-481033 Ø12 X 16L Spacer Tube 4

11
Pos SAP Part No Description Qty
37 10985376 EOSM-481034 Valve Tap 1
38 10985377 EOSM-481035 Valve Mounting Base 1
39 10985347 EOSM-481007 M6 (6x16x1.0) Washer 4
40 10985348 EOSM-481008 1/4”- 20 Nut 4
41 10985378 EOSM-481036 M5x0.8x8L-90L Hex Screw 1
42 10985379 EOSM-481037 Lifting Handle 2
43 10985361 EOSM-481020 M5 (5x10x1.0) Washer 4
44 10985380 EOSM-481038 M5 X 0.8 X 12L Screw 4
45 10985361 EOSM-481020 M5 (5x10x1.0) Washer 1
46 10985360 EOSM-481019 M5 X 0.8 Nut 1
47 10985381 EOSM-481039 Ø12 X 66L Spacer Tube 4
48 10985382 EOSM-481040 1/4”-20x6-3/4” Head Screw 4
49 10985348 EOSM-481008 1/4”- 20 Nut 4
50 10985383 EOSM-481041 Tank Cover 1
51 10985347 EOSM-481007 M6 (6x16x1.0) Washer 4
52 10985348 EOSM-481008 1/4”- 20 Nut 4
53 10985384 EOSM-481042 12mm Gasket 1
54 10985360 EOSM-481019 M5 X 0.8 Nut 6
55 10985361 EOSM-481020 M5 (5x10x1.0) Washer 6
56 10985385 EOSM-481043 Fluid Overow Funnel 1
57 10985386 EOSM-481044 TP 3/16”x3/8”L SUS Screw 6
58 10985387 EOSM-481045 Float Sponge 1
59 10985388 EOSM-481046 Float Ball 1
60 10985361 EOSM-481020 M5 (5x10x1.0) Washer 4
61 10985360 EOSM-481019 M5 X 0.8 Nut 4
62 10985390 EOSM-481047 Float Retention Wire 1
63 10985389 EOSM-481048 Float Retention Wire 1
64 10985391 EOSM-481049 Polyester Filter 1
65 10985361 EOSM-481020 M5 (5x10x1.0) Washer 2
66 10985380 EOSM-481038 M5 X 0.8 X 12L Screw 2
67 10985392 EOSM-481050 Tension Spring 2
68 10985393 EOSM-481051 Filter Retaining Hook 1
69 10985448 EOSM-481052 Cloth Filter Frame 1
70 10985449 EOSM-481053 Cloth Filter 1
71 10985450 EOSM-481054 20 Gallon Tank 1
72 10985395 EOSM-481055 Latch 4
73 10985396 EOSM-481056 Rivet (SUS) 8.5x4.8x6.5 8

12
Pos SAP Part No Description Qty
74 10985361 EOSM-481020 M5 (5x10x1.0) Washer 8
75 10985397 EOSM-481057 Air Intake Guide Tube 1
76 10985398 EOSM-481058 Air Intake Guide Tube 1
77 10985399 EOSM-481059 Gasket 1
78 10985400 EOSM-481060 Compression Spring 1
79 10985401 EOSM-481061 Latch 1
80 10985402 EOSM-481062 Air Intake Cover 1
81 10985403 EOSM-481063 Spring Release Latch 1
82 10985405 EOSM-481064 TP 3/16 X 1”L SUS Screw 4
83 10985421 EOSM-481065 Mounting Bracket 1
84 10985422 EOSM-481066 M5 X 0.8 X 10L SUS Screw 4
85 10985361 EOSM-481020 M5 (5x10x1.0) Washer 8
86 10985420 EOSM-481067 M5 X 0.8 Cap Nut 4
87 10985423 EOSM-481068 Push Cart Handle 1
88 10985424 EOSM-481069 Cart Frame 1
89 10985425 EOSM-481070 Spring Snap Pin 2
90 10985426 EOSM-481071 Accessories Bag 1
91 10985427 EOSM-481072 1/2” Washer 4
92 10985428 EOSM-481073 1/2” External E-Clip 2
93 10985429 EOSM-481074 Ø8” Wheel 2
94 10985430 EOSM-481075 Ø0.5 X 577mm Steel Bar 1
95 10985431 EOSM-481076 3/8” Washer 2
96 10985432 EOSM-481077 3/8” Spring Washer 2
97 10985433 EOSM-481078 3/8” - 16 Nut 4
98 10985434 EOSM-481079 3”x3/8x19 Caster Wheel 1
99 10985435 EOSM-481080 3”x3/8x19 Wheel W/Brake 1
100 10985436 EOSM-481081 AL305+501/EU Power Plug 1
101 10985437 EOSM-481082 AL302+501/EU Power Plug 1
102 10985438 EOSM-481083 AL203+501/EU Power Plug 1
103 10985439 EOSM-481084 AL307+501/EU Power Plug 1
104 10986245 EOSM-481129 Wide nozzle 1
105 10986244 EOSM-481128 Round brush 1
106 10986243 EOSM-481127 Narrow nozzle 1
107 10986242 EOSM-481126 Squeegee 2
108 10986239 EOSM-481123 Hose 1
109 10986240 EOSM-481124 L-pipe 1
110 10986241 EOSM-481125 Extension wand 2
111 10985394 EOSM-481096 Tank Gasket 1

Exploded View
11

EC Declaration of Conformity
Description Vacuum cleaner VCE2000U
Type designation VCE2000U
Year of construction 2007
We declare under our own liability that this product complies with the following directives and standards:
Directive applied:
European Machine Directive 98/37/CEE
European EMC Directive 9/336/CEE
European Low Votage Directive 73/23/CEE
EN 2002/96/EG Waste electrical and electronic equipment
Standards applied
EN 294 Safety of machinery – Safety distances to prevent upper limbs
reaching danger areas
Roland Kägi
Equipment Manager
TYROLIT Hydrostress AG
Witzbergstrasse 18
CH-8330 Pfäkon
Switzerland