HYPERVSN MS User manual

© Copyright 2020 HYPERVSN. All rights reserved 1
See extraordinary
OPERATING MANUAL
Integrated 3D Holographic Display System

2 © Copyright 2020 HYPERVSN. All rights reserved
TABLE OF CONTENTS
1. DEVICE OVERVIEW............................................................................ 4
2. TECHNICAL SPECIFICATIONS............................................................7
3. PACKAGE CONTENTS ........................................................................ 9
4. DEVICE INSTALLATION AREAS ......................................................10
4.1 PROHIBITED AREAS............................................................... 10
4.2 INSTALLATION REQUIREMENTS....................................... 10
4.3 INSTALLATION RECOMMENDATIONS ............................. 11
5. DEVICE ASSEMBLY ............................................................................ 12
6. DEVICE INSTALLATION ....................................................................14
7. OVERVIEW OF DEVICE OPERATING MODES ..............................16
7.1 OPERATING MODES................................................................16
7.2 SWITCHING THE DEVICE ON AND OFF ............................17
7.3 STATUS INDICATORS OF THE DEVICE ............................ 18
8. CMS ACCOUNT REGISTRATION, DEVICE ACTIVATION,
CALIBRATION .................................................................................... 20
8.1 CMS ACCOUNT REGISTRATION.........................................20
8.2 DEVICE ACTIVATION AND CALIBRATION ...................... 23
9. TECHNICAL MAINTENANCE............................................................33
10. SAFETY PROVISIONS ........................................................................35
11. MAINTENANCE, WARRANTY AND DISPOSAL ............................37
11.1 MAINTENANCE........................................................................ 37
11.2 WARRANTY .............................................................................. 37
11.3 DISPOSAL................................................................................... 37
12. SPECIAL REQUIREMENTS ............................................................... 38
M20MS11

© Copyright 2020 HYPERVSN. All rights reserved 3
Thank you for purchasing our product.
WARNING. This Operating Manual must be thoroughly read and
understood before installation, operation and use of HYPERVSN Device.
This Operating Manual is designed as a general guide for HYPERVSN Models MS and
MS-L (hereinafter referred to as, the “Device”).
This Operating Manual provides an overview, safety rules and requirements, technical
specifications and other important information required to assemble, install and operate
the Device.
Kino-mo Ltd, the manufacturer, disclaims all liability for any harm caused to the user or
viewers by improper Device operation and use.
No changes should be made to the equipment without the manufacturer’s permission as
this may void the user’s authority to operate the Device.
SAFETY AND OTHER SYMBOLS
The following symbols are found on the exterior of the Device and in this manual:
Table 1. Safety and other symbols
SYMBOL
MEANING
CE marking
Eurasian Conformity mark
Protective Earth (grounding)
22/99 RAEE
Disposal
See section 11.3.

4 © Copyright 2020 HYPERVSN. All rights reserved
1. DEVICE OVERVIEW
The Device is a cutting-edge visual solution, designed for creating, managing and
displaying 3D video content perceived by viewers as high-resolution holograms floating
in mid-air.
Picture 1. General view of the Device
Note. The Device’s appearance may vary slightly from the pictures presented in this
manual.
•The Device’s spinning rays create a surface on which 3D video content can be
displayed.
•The Device displays holographic visuals up to 56 cm in size (model MS - with 56 cm
rays) or up to 75 cm in size (model MS-L - with 75 cm rays).
•The Device is managed through the proprietary Content Management System
(hereinafter referred to as, the “CMS”). It allows you to create your own content
library, schedule playlists and collect analytics to evaluate the success of your
media campaigns.
•The content is uploaded via a Wi-Fi connection.
•The Device and its content can be controlled and managed via a mobile application.
Note. For detailed information, see the User Guide for the HYPERVSN Solo Application.
(https://hypervsn.com/media/SoloApp/User_guide.pdf).
•The Device is designed for static mounting on walls or custom-made, stand-alone
structures.

© Copyright 2020 HYPERVSN. All rights reserved 5
Key components
•Rotor (with four rays)
•Stator
•Wall bracket
•Remote control
Picture 2. Key Device components and the remote control
Configuration options
Devices can be installed according to one of several specific patterns and synchronized.
These multiple Devices working together form the HYPERVSN Wall, which allows for
the display of a single, large 3D image.
Picture 3. HYPERVSN Wall
rays
shaft
indicators
WALL BRACKET
ROTOR
STATOR
REMOTE CONTROL

6 © Copyright 2020 HYPERVSN. All rights reserved
The Device (and the HYPERVSN Wall) can be equipped with the HYPERVSN
MasterBox. It is an additional component that connects to the Device or the HYPERVSN
Wall to provide additional functionality (including possibility of synchronized sound
reproduction when the audio facilities are connected to).
Picture 4. General view of the HYPERVSN MasterBox
Note. For more detailed information about the MasterBox, see its exclusive Operating
Manual.
A range of customized mounts for Device installations are available at an additional
cost at customer’s request.
The HYPERVSN Dome (hereinafter referred to as, the “dome”) is an optional Device
accessory (Picture 5). It is designed to prevent possible damage to the Device and to
provide safety to viewers. This add-on is particularly important in instances, where the
Device is going to be mounted lower than the specified precautionary height. The dome
is supplied on customer request at an additional cost. The Dome is available in models M,
L and Ultra.
Picture 5. Device (56 cm rays) with the HYPERVSN Dome Model M installed

© Copyright 2020 HYPERVSN. All rights reserved 7
2. TECHNICAL SPECIFICATIONS
Table 2. Indoor operating environment for Device
CONDITIONS
VALUE
Air temperature range
From 0°C to 35°C+
Relative humidity
Up to 75%
Table 3. Basic technical specifications of Device
PARAMETERS
DESCRIPTION
VALUE
MS Model
(with 56 cm rays)
MS-L Model
(with 75 cm rays)
Maximum image size
(diameter)
567 mm
750 mm
Diameter
567 mm
750 mm
Depth
174 mm
174 mm
Number of rays
4
4
Rotation speed
670 RPM
670 RPM
Number of LEDs per each
ray
168
216
Input voltage
100-240 V
100-240 V
Current
2.0 A
2.0 A
Input AC frequency
50/60 Hz
50/60 Hz
Average power
40 W
60 W
Peak power
200 W
200 W
Net weight
2.8 kg
2.9 kg
Noise figure on the Device
axis (1m from the Device)
45 Db
50 Db
Fuse
ceramic 4A 250VAC
5X20 mm
ceramic 4A 250VAC
5X20 mm
Power cable length
3 m
3 m
Power cable thickness
8 mm (max)
8 mm (max)

8 © Copyright 2020 HYPERVSN. All rights reserved
PARAMETERS
DESCRIPTION
VALUE
MS Model
(with 56 cm rays)
MS-L Model
(with 75 cm rays)
AC plug
B, F, G, H type
AC plug type is dependent
upon the country
of destination (consumer
region)
B, F, G, H type
AC plug type is dependent
upon the country
of destination (consumer
region)
Remote control
IR type
IR type
Battery
(for remote control)
CR2032, 3 V
CR2032, 3 V
Applicability for
the HYPERVSN Wall
applicable
not applicable
The Device has Class B electromagnetic compatibility.
The Device is to be connected to single-phase alternating current mains (with 100-240 V
voltage and 50/60 Hz frequency) and can be operated continuously while plugged in.
Sync cable specifications
•Rj14
•4-wire
•with 6P4C connectors
•straight –pinned
(white - orange) 1 1
(blue) 2 2
(white - blue) 3 3
(orange)4 4
MTBF
•Rotor:150,000 h
•Stator: 150,000 h
•LED rays: 120,000 h
(at temperature 25°C+, humidity 50%. MIL-HDBK-217F method is utilized)
Important. The HYPERVSN Wall can only be formed with Model MS. Model
MS-L is not compatible with the HYPERVSN Wall. We are not able to guarantee
proper operation and functionality of the HYPERVSN Wall, should Model MS-L
be used. Our regular warranty will not cover Model MS-L Devices used
in HYPERVN Walls.

© Copyright 2020 HYPERVSN. All rights reserved 9
3. PACKAGE CONTENTS
Table 4. Package contents
COMPONENT NAME
QUANTITY (# OF PIECES)
Stator + Rotor
1 + 1
Rays
4
Wall bracket
1
Remote control
1
Screw M2,5x5
4
Safety bolt
1
Hexagon 2 mm
1
Philips (PH0) screwdriver
1
Operating Manual
1
Tools and fittings required (not supplied)
To assemble and install the Device, the following tools and fittings (that are not supplied
with the Device) are needed:
•Philips (PH2) screwdriver –to assemble the safety bolt.
•Drill –to make holes in a wall, where the Device will be mounted.
Hole diameters:
a) Partitioned walls –5.3 mm,
b) Concrete walls –5.0 mm.
•Fasteners –3 pieces to attach the wall bracket (M5 mounting hardware,
appropriate for the mounting surface –either a partitioned or a concrete wall).
Attention. This set of tools and fittings listed above are intended for the mounting of
the Device onto the wall bracket supplied with the Device. In the event that the Device
will be installed with another HYPERVSN accessory, see the Operating Manual for these
instructions.

10 © Copyright 2020 HYPERVSN. All rights reserved
4. DEVICE INSTALLATION AREAS
4.1 PROHIBITED AREAS
WARNING. Regardless of its height, do not install the Device in the
following areas:
1. Children’s playgrounds.
2. Animal’s open-air cages.
3. Areas easily accessible to domestic pets (cats, dogs, etc.).
WARNING. Do not install the Device without the dome in the following
areas:
4. Areas where birds or insects may come into contact with the Device.
5. Next to any objects (curtains, drapes) that could potentially (under the influence
of wind or other external factors) come into contact with the Device.
4.2 INSTALLATION REQUIREMENTS
1. The Device must be installed out of public reach. Solutions include, but are not
limited to:
•Custom-made, stand-alone installations.
•Closed display cases (provided that the personnel on site follow all safety
guidelines).
•Installations in public places, where the mounting height must be at least 3.1 m.
Note. The mounting height is defined as the distance from the floor level to the lowest
point of the rotating elements.
2. The Device may be installed at a height under 3.1 m. In this case, the Device must
be surrounded by some sort of barrier that strictly forbids audiences from crossing
it. There must be a minimum of 3 m between the Device and the safety barrier.
WARNING. The Device must remain at a safe distance from viewers.
3. Do not install the Device in areas affected by high temperatures, heavy
steam/vapor, large volumes of dust, air conditioners, radiators, ovens and other
similar equipment. Ensure that the Device is properly ventilated.