Hyundai IT D320ML User manual
U.S.A.
U.S.FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
INFORMATION TO THE USER
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
aÚReorient or relocate the receiving antenna.
aÚIncrease the separation between the equipment and receiver.
aÚConnect the equipment into an outlet of a circuit different from that to which the receiver is connected.
aÚConsult the dealer or an experienced radio/TV technician for assistance.
Changes or modification not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
Connecting of peripherals requires the use of grounded shielded signal cables.
,54G-6/GQVLL !""85
DECLARATION OF CONFORMITY
WE HYUNDAI IT CORP.
Ami-ri Bubal-Eub Ichon-Si Kyungki-Do
467-860 KOREA
declare under our sole responsibility that the product:
to which this declaration relates is in conformity with the following
standard(s) or other normative document(s)
following the provisions of the Low Voltage Directive 73/23/EEC,
93/68/EEC and the EMC Directive 89/336/EEC.
Jong Won, Choi Ho Suk, Chon
(Name and signature of authorized person)
KOREA / July 1, 2008
(Place and date of issue)
Kind of equipment : DID
Type-Designation : S40M0G010 / LT46DW001 / S57M0F010
Safety : EN60950-1:2002
EMC : EN 55022/1998+A1:2000+A2:2003
EN 55024 :1998+A1:2001+A2:2003
EN 61000-3-2:2000
EN 61000-3-3:1995+A1:2001
TUV SUD Product Service GmbH
Zertifizierstelle, Ridlerstrasse
65, 80339 Munchen, Germany
Accredited testlaboratory
TÜV Rheinland
Am Grauen Stein
51105 Köln
LT46DW001 :
S40M0G010 :
S57M0F010
,54G-6/GQVLL !""85
DIGITAL SIGNAGE
Major features
...................................................... 1/34
Direction for the use
........................................... 1/34
Be sure to understand
......................................... 3/34
Checking product list
.......................................... 5/34
Proper place for product
Installation
........................................................... 6/34
Title and function of each part
.......................... 7/34
Front part.............................................................. 7/34
Rear part .............................................................. 8/34
Remote control...................................................... 9/34
How to insert battery into remote control.............. 9/34
How to connect HDMI
....................................... 10/34
Support timing for Digital RGB ........................... 11/34
Corrections
How to connect analog RGB (PC D_SUB)
........12/34
Supporting timing for PC ..................................13/34
How to Connect component
..........................14/34
Supporting timing for component & AV ............15/34
How to Connect the video
..............................16/34
OSD adjustment and fucntion
.........................17/34
Diagnosis
...........................................................31/34
Product specification
.......................................33/34
ENGLISH
,54G-6/GQVLL !""85
DIGITAL SIGNAGE
-1/34-
Major features
Direction for the use
This product has been designed to enable the user ease of use, and display information
effectively and conveniently.
aÚ77ÚÚ"¬låvÚJl¬»Üvl
D320ML/D400ML/D420ML/D460ML : 1366 x 768 WXGA (HD)
D525ML/D575ML/D705ML : 1920 x 1080 UWXGA (FHD)
aÚëëlÚlÜJÚb¬¬ÐÚlÓ»Jî
aÚ%4Úb¬¨ÜЬÚå¨bܬ¨
aÚåܬ£JÜbÚ£JvÚb¬¨ÜЬ
aÚåܬ£JÜbÚÜv£»vÐJÜåÐvÚb¬¨ÜЬ
aÚ¨J¬ÙÜJÚ3½"¾Ú¨»åÜÚJ¨lÚ¬åÜ»åÜ
aÚEÚ.XÚ.ÐÙAÚ¨»åÜÚJ¨lÚ¬åÜ»åÜ
aÚåÜÚ¨Ú£åÜëÓ¬¨Úå¨bܬ¨Ú
This Product is designed to ensure user's safety.
Avoid the following items prevents from serious electric shot and other dangers.
-Do not place wet objects on or around the product or the power cord.
- Do not cover or insert anything over or into the ventilation openings.
- Do not place in a location where damaged from oil, Smoke, high temperature, high
humidity, dust etc can be caused.
,54G-6/GQVLL !""85
DIGITAL SIGNAGE
-2/34-
ENGLISH
- The product is not suitable for use at visual display workplaces according to §2
of the German Ordinance for Work with Visual Display Units.
- The mains plug of the power supply cord shall remain readily operable.
- An apparatus with CLASS I construction shall be connected to a Mains socket outlet
with a protective earthing connection.
- Make sure the power cord and other cables are correctly plugged in.
- Plug the power cord correctly into the end, do not wobble/jiggle, it may cause electric shock fire.
- Do not touch the power cord with wet hands, it may cause electric shock.
- Overloaded AC outlets and extension cables are as dangerous as the power cord being
damaged, call service engineer for replacement as it may cause electric shock or fire.
- Do not use multiple devices in a single power outlet, it may cause overheating or fire.
- Do not use or place sharp objects near the LCD surface, as this can cause damage to the screen
itself.
- When cleaning the LCD screen / Surface, do not use chemical cleaning products as this can
seriously damage the special coatings on the screen. Only use water to dampen a soft cloth
and lightly clear the screen.
- Over time dust deposits can build up inside the product, this can cause the product to overheat
thus causing premature malfunction or fire. Please do not attempt to clean the inside of the
product yourself, please contact the local service agent.
- Do not use alcohol or strong chemical solvent such as methyl, ethyl or a Isopropyl.
- In the case of cleaning, be sure to remove the power cord and wip with a soft dry fabric.
- Keep batteries for the remote control out of children's sight.
- Make sure that power cord or other cables are correctly plugged in.
,54G-6/GQVLL !""85
DIGITAL SIGNAGE
-3/34-
Be sure to
understand
- Batteries should be inserted using the correct polarity (+,-).
- Use only new batteries, do not mix old & new.
- Place unit on a stable bracket or surace.
- More than 2 persons should work together when moving or installing.
- Do not hang on or jump to the product or mounting rack.
- When the product be left unused for a long time, be sure to unplug the power cord.
- In the case of damage or breakage do not attempt to self repair, please contact local
service engineer.
Image quality of the product
CAUSE
- Due to the nature of LCD's property, Afterimage can occur. Afterimage appears when
identical frames / images are displayed continuasly. If displayed for prolonged periods
of time this can become permanent.
PREVENTION
When you display a freeze frame for a long time, lower the brightness and contrast
(Brightness, 70/ Contrast, 80). Also it can be prevented by using moving frame.
,54G-6/GQVLL !""85
DIGITAL SIGNAGE
-4/34-
ENGLISH
PREVENTION
Temporary afterimage can be alleviated by displaying white or moving frame about 10
hours.(But, permanent afterimage cannot be disappeared according to the property of
LCD) This method is used to remove temporary afterimage that may occur after
displaying a still frame for a certain times.
It can take several minutes or hours to remove afterimage according to the severity. In
the case that your cannot avoid displaying identical still image continuously, you can
prevent it by displaying moving image for 2 or 3 minutes in every hour. As the
brightness of still image and time of display are the cause of afterimage, you are
recommended to lower the brightness in that case.
Above problem shall not be covered by warranty.
!
,54G-6/GQVLL !""85
DIGITAL SIGNAGE
-5
/
34
-
Please check the following components provided with the product after you open the box.
please check the following components provided with the product after you open
the box and contact the dealer if any missing.
Check the product
list
!
HDMI ca
bl
e
Remote contro
l
&
b
atterie
s
Power Cor
d
User
'
s manua
l
Pro
d
uc
t
HDMI to DVI Cable
(Option
)
D-SUB Ca
ble
(Option
)
able
(Option)
85
8
5
DIGITAL SIGNAGE
-6/34-
ENGLISH
Proper location for
product installation
1. Locate the product at least 30cm away from the electric appliance or heating product.
2. The product must be placed at least 10cm away from the wall and ground.
3. Keep the product out of direct ray of light and locate screen not to be reflected by the
sunlight.
4. Make sure the mounting rack firmly tightened before installation.
Please take extra care during installation, it is possible to cause damage if the unit is
handled badly or knocked.
!
,54G-6/GQVLL !""85
DIGITAL SIGNAGE
-7/34-
Title and function of
each part
Front panel
Remote control receiving sensor.
Power display LED red-stand by/ Green-working.
~ OSD button.
Power button ; to turn the power on or off.
Input selection button : to select other connected
device.
Menu button : to display menu or exit from the menu.
select button.
To move down in OSD menu.
To move up in OSD menu.
To move left and control the volume down in OSD menu.
To move right and control the volume up OSD menu.
POWER SOURCE MENU SELECT
VOL
,54G-6/GQVLL !"" 85
DIGITAL SIGNAGE
-8/34-
ENGLISH
Rear panel
AC IN
AC POWER SWITCH
HDMI IN
HDMI OUT
SPEAKER OUT
PC D-SUB IN
PC D-SUB OUT
UPGRADE
PC AUDIO IN
RS-232C OUT
RS-232C IN
COMPONENT IN (Y Pb Pr)
COMPONENT OUT (Y Pb Pr)
!
CVBS IN
CVBS OUT
COMPONENT AUDIO IN (L R)
COMPOSITE AUDIO IN (L R)
!
"
#
$
"
#
$
,54G-6/GQVLL !""!85
DIGITAL SIGNAGE
-9/34-
Remote control
How to insert batteries
Pull while pressing ∆ at rear lid. Insert the batteries into proper polarities
(+,-).
Use after the lid closed.
123
To turn the power on or off.
Move up in OSD menu.
To move left or control the volume down in OSD
menu.
To move right or control the volume up in OSD menu.
To move down in OSD menu.
Select in OSD menu.
Display the menu screen.
Close the menu screen.
Convert the input signal.
,54G-6/GQVLL! !""85
DIGITAL SIGNAGE
-10/34-
ENGLISH
How to Connecting
Digital RGB(HDMI)
1. Please ensure that the power to the device is switched off, then connect each cable
one after another before restoring power.
when connect HDMI to HDMI cable
when connect DVI to HDMI cable
– must utilize device with DVI signal output from peripheral device
2. Connect the power code to the product.
3. Turn on the power of product and peripheral device. Screen shows up within 10
seconds.
4. Select "HDMI" input by pressing "SOURCE" on OSD button or remote control.
– HDMI input gives better video quality than analog RGB input.
– Both HDMI and analog RGB support plug and play.
,54G-6/GQVLL !""85
DIGITAL SIGNAGE
-11/34-
Support timing for
HDMI
9, 10, 11 and 12 are only for Full HD
1
2
3
4
5
6
7
8
9
10
11
12
480p
576p
720p
1080i
640 x 480
800 x 600
1024 x 768
1360 x 768
1280 x 1024
1600 x 1200
1920 x 1080
1080p
640 x 480p
720 x 576p
1280 x 720p
1920 x 1080i
31.47
37.88
48.36
47.70
64.00
75.00
67.50
1920 x 1080p
60
50
50 / 60
50 / 60
59.94
60.32
60
60
60
60
60
60
Vertical frequency
(Hz)
Horizontal frequency
(KHz)
Resolution
NO
!
,54G-6/GQVLL !""85
DIGITAL SIGNAGE
-12/34-
ENGLISH
1. Please ensure that the power to the device is switched off, then connect each cable one
after another before restoring power.
2. Connect D-SUB to D-Sub cable. Then tighten the screw of the cable after connecting PC
D-SUB.
3. Connect the power cord to the product.
4. Turn on the power of product and PC . The screen will appear within 10 seconds.
5. Select "PC" input by pressing "SOURCE" on OSD button or remote control.
– HDMI input gives better video quality than analog RGB input.
– Both HDMI and analog RGB support plug and play.
How to Connecting
analog RGB
(PC D-SUB)
,54G-6/GQVLL !""85
DIGITAL SIGNAGE
-13/34-
Support timing for PC
1
2
3
4
5
6
7
640 x 480
800 x 600
1024 x 768
1360 x 768
1280 x 1024
1600 x 1200
1920 x 1080
31.47
37.88
48.36
47.71
64.00
75.00
67.50
59.94
60.32
60.00
60.00
60.00
60.00
60.00
Vertical frequency(Hz)
Horizontal frequency(KHz)
ResolutionNO
!
5, 6 and 7 are only for Full HD
,54G-6/GQVLL !""85
DIGITAL SIGNAGE
-14/34-
ENGLISH
1. Please ensure that the power to the device is switched off, then connect each cable one
after another before restoring power.
2. Connect the component cables to Y, Pb, and Pr correctly.
Connect BNC cable and tighten.
3. Connect the power cord to the product.
4. Turn on the power of product and peripheral device .
The screen will appear within 10 seconds.
5. Select "COMPONENT" input by pressing "SOURCE" on OSD button or remote control.
How to Connecting
the component
,54G-6/GQVLL !""85
DIGITAL SIGNAGE
-15/34-
Support timing for
component & AV
1
2
3
4
5
6
7
480i
480p
576i
576p
720p
1080i
1080p
720 x 480i
640 x 480p
420 x 480p
720 x 576i
720 x 576p
1280 x 720p
1920 x 1080i
1920 x 1080p
59.94 / 60
59.94 / 60
59.94 / 60
50
50
59.94 / 60 / 50
59.94 / 60 / 50
60 / 50
Vertical frequency
(Hz)
Horizontal frequency
(KHz)
Resolution
NO
!
7 is only for Full HD
,54G-6/GQVLL !""85
DIGITAL SIGNAGE
-16/34-
ENGLISH
How to Connecting
the the video
1. Please ensure that the power to the device is switched off, then connect each cable
one after another before restoring power.
2. Connect video cable and BNC cable, and then tighten.
3. Connect the power cord to the product.
4. Turn on the power of product and peripheral device .
The screen will appear within 10 seconds.
5. Select AV input by pressing "SOURCE" on OSD button or remote control.
,54G-6/GQVLL !""85
This manual suits for next models
6
Table of contents
