Hyundai HLT-2310 User manual

`
SERVICE MANUAL
HLT-2310 / HLT-3010
23”/30" TFT-LCD TV/MONITOR

CONTENTS
1. SAFETY PRECAUTION  2
2. BLOCK DIAGRAM  3
3. TROUBLE SHOOTING  9
4. CONTROLS OF FRONT PANEL  12
5. CONNECTIONS OF BACK PANEL  13
6. REMOTE CONTROL HANDSET  14
7. CONNECTING DIAGRAM  15
8. PCB LAYOUT  16
9. SCHEMATIC DIAGRAM  24
10. EXPLODED VIEW 38
11. REPLACEMENT PARTS LIST  46

1. Safety Instructions
Important Safety Notice
Many electrical and mechanical parts in this chassis have special safety-related characteristics.
These parts are identified by in the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet. Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water
Pipe, Conduit, etc) and the exposed metallic parts. Measure the AC voltage across the resistor using AC
voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug of the AC cord into the AC outlet and repeat
AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt
RMS, which is, corresponds to 0.5mA. In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.
AC Volt-meter
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
1.5 Kohm/10W
0.15uF
To Instrument’s
exposed
METALLIC PARTS
AC Volt-meter
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
1.5 Kohm/10W
0.15uF
To Instrument’s
exposed
METALLIC PARTS

2. BLOCK DIAGRAM
■BLOCK DIAGRAM
`
SCART2_LO/ RO
SW_FB/R/G/B
DTV_Y/ Pr/ Pb
480I_Y/Cb/Cr(S)
J- L003
TxT_Vout
H- DET
TxT_Vout
H- DET
VO_R[ 0 . . 7] VO_B[ 0..7]
V0_G[ 0..7]
DIG[ 0..23]
OP_HSYNC
OP_VSYNC
PCLK_OUT
OP_ENABLE
SVP_HSYNC
SVP_VSYNC
SVP_PCLK
SVP_ENABLE
LCD
LVDS
PanelTV-
SVP
BGA 320
TPA3001
MSP3410
S- VIDIO
COMP
(RCA_L/R)
TUNER
F_SCART H_SCART
DVI_I
COMPONENT
VPC3230
AD9882
CXA2069
SVHS_C
SVHS_Y
SCART2_VI/ LI/ RI
SCART2_ID
SCART2_VO
TV_V
SIF/ AM_AUDIO
TV_O
SCART1_VI/ LI/ RI
SCART1_ID
SCART_FB/ R/ G/ B
COMP_L/ R
CVBS(S)
Y_OUT(S)
C_OUT(S)
TV_L/ R
TV_L/ R
TV_L/ R
PI5V330
BA7657
TR
COMP_Y/ Pr/
Pb
AUDIO_R/ L
AUDIO_R/ L
480i_Y/ Cb/ Cr(M)
TXT_FB/R/G/B
PC
(DSUB- 15)
74HCT08
PC_VS/ HS
VPC_HS/ VS
VPC_HS/ VS
VPC_HS1/ VS1
PC_VS/HS
PC_R/G/B
PC_DTV_HS/ VS
(VPC_HS1/ VS1)
PC_R/ Pr
PC_G/ Y
PC_B/ Pb
CAPD[ 0..23]
HSMP / HSPIP
VSMP / VSPIP
CLKMP / CLKPIP
CAPD
[ 8..23]
SDRAM
X2
SDA555
SDRAM
EEPROM
TXT_FB/R/G/B
CPU_INT
CPU_WR
CPU_RD
CPU_ALE
VPC_VS1 / HS1
CPU_AD[ 0..7]
L_SPK
R_SPK
SPEAKER
DPTV- 23/ 30 Block Diagram
CVBS(M)/Y_OUT(M)/C_OUT(M)
SIF/ AM_AUDIO
EEPROM
EEPROM
EPROM
PC_AUDIO
JACK
PC_AUDIO_L/ R
D- SUB9 DS232 RXD_UART
TXD_UART
TXT_FB,
(FB2_SVP)
TXT_FB,
(FB2_SVP)

■IC FUNCTIONAL BLOCK DIAGRAM (PanelTV-SVP)
■IC BALL ASSIGNMENT (PanelTV-SVP)

■IC BLOCK DIAGRAM (MSP3410G)
■IC PIN OUT (MSP3410G)

■IC BLOCK DIAGRAM (TPA3001D2)
■IC PIN OUT (TPA3001D2)

■IC BLOCK DIAGRAM (VPC3202D-C5)
■IC PIN OUT (VPC3202D-C5)

■IC BLOCK DIAGRAM (AD9882)
■IC PIN OUT (AD9882)

3. TROUBLESHOOTING
No Raster
Check
P1004,P1005
Connector?
Fasten
P701 or P702
Connector
Fasten
P1004,P1005
Connector
Contact A/S Team
Check
P701 or P702
Connector?
YES
NO
NO
YES
No Raster
Check
P1001 or P1007,
P1008
Connector?
Fasten P1001
or P1007, P1008
Connector
NO
YES
YES
Check
P101,P102
Connector?
Fasten
P101,P102
Connector
NO
YES