Hyundai H-LED19V8 User manual

LED TV
Руководство по эксплуатации Instruction manual
H-LED19V8
ТЕЛЕВИЗОР
ЦВЕТНОГО ИЗОБРАЖЕНИЯ
ЖИДКОКРИСТАЛЛИЧЕСКИЙ
(LCD)
ME61

Table of contents
Before you start
Utilization of the product
Important safeguards
Installation
Stand installation
Connection
Connection
Outdoor antenna connection
Other connections
Operation
Control elements
Front panel
Back panel
Remote controller
Changing the battery
General operations
Teletext operations
OSD operation
Picture setting
Sound setting
Setting page
Geometry setting
Channel setting
USB operation
General information
File playback
General information
Troubleshooting
Causes of interference
Accessories
Specifications
2 3
Table of contents Before you start
Dear customer!
Thank you for purchasing our product. For safety, it is strongly recommended to read
this manual carefully before connecting, operating and/or adjusting the product and keep
the manual for reference in the future.
2
3
3
3
4
4
5
5
5
5
6
6
6
6
7
7
8
8
8
9
9
9
10
10
10
10
11
12
12
12
13
13

2 3
Table of contents Before you start
If you want to dispose this product, do not mix it with general household waste. There is
a separate collection system for used electronic products in accordance with legislation
that requires proper treatment, recovery and recycling.
Please contact your local authorities for the correct method of disposal. By doing so,
you will ensure that your disposed product undergoes the necessary treatment, recovery
and recycling and thus prevent potential negative effects on the environment and human
health.
Utilization of the product
Important safeguards
• Before connecting the AC power cord
to the DC adapter outlet, make sure that
the voltage designation of the DC adapter
corresponds to the local electrical supply.
• Accessories include a DC adaptor SAWA-
12-50012. Do not use other adaptors with this
unit.
• Please unplug the power cord from the AC
outlet and contact a service center for repair
if following occurs: any obvious abnormality
appears in the unit, such as smoky, peculiar
smell or strange sound; liquid has been spilled or
other objects have fallen into the unit; no picture
or sound; cover or panel is broken; although you
have operated the unit following the operating
instructions, it still cannot work normally.
• This unit should only be connected to a
wall socket having grounding.
• Always disconnect the power cord and
antenna during a storm.
• Do not fix the power cord with a metal nail.
• Unplug the power cord from the AC outlet;
also unplug the signal cables from the input
ports when the unit is unused for long periods
of time.
• When unplugging the plug, always hold
the wide slot, do not touch the metal part, and
do not destroy, refit, twist, pull or roast the
power cord.
• Please contact the service center
immediately if you found that the core is
showed in the air or has been broken.
• Please replace the AC outlet if the metal
bolt cannot be inserted into the power socket
completely or it cannot be fastened even when
it was pushed in, otherwise, any accidents of
shocks and fires would happen.
• Never touch the antenna lie or power plug
if it stars to thunder.
• Do not touch the power plug with wet
hands.
• Do not use any non-rated power socket
with numerous devices jointed on one power
socket or cable device. The wire of non-
designated capacity may cause the fire due to
the generation of heat.
• All instructions must be read and
understood well before you operate the unit.
Heed all warnings and follow all instructions.
• Please use the accessories provided
by the manufacturer. Using inadequate
accessories may result in accidents.
• Please adjust the product through the
panel buttons or the remote controller, do
not remove the cover or attempt to service
the product by yourself. Do not disassemble
back cover and do not make maintenance by
yourself to avoid the electric shock.
• Over-press the panel may destroy the
product.
• Do not place the product on an unstable
cart, stand surface, tripod, bracket, or table.
The product may fall, causing serious accidents
as well as the damage to the product.

4
Before you start
• Please place the product on a flat surface
in a well-ventilated location. Keep it away from
the burning-light, direct sunlight, vibration,
high-temperature and humidity.
• Do not place any vase, potted plant, cup,
medicine and any container with water on this
product. If the liquid is spilt, it may cause the
fire, electric shock or breakdown.
• Do not install it at the place on the strong
magnetic field or current field. It may cause
break down. This equipment may be observed
deterioration of the picture by electromagnetic
radiation in electromagnetic environment.
• Fasten the wheel of the product or shelf
with wheels when installing this product. If it
moves or is tipped over, it may be damaged.
• Do not place any fire source such as
candlelight close to this product or place it on
this product. If it is tipped over or fallen down, it
may cause damage or fire.
• Do not place the unit into closed space
of TV for better ventilation; it can reduce the
product lifetime. Keep a space at least 10 cm
at above, left and right of the TV.
• Please place all the signal cords behind of
rear panel.
• Do not overexert or touch the panel when
you convey the product. Do not transfer the
LED TV up or down display direction.
• Do not transport it with the power cord
or the connection cable connected. If you
move this product with the power cord or the
connection cable connected, the damaged
power cord, connection cable or connection
terminal may cause the fire, the electric shock
or breakdown.
• 2 persons or more shall transport the
device, which is heavier than 18 kg. If you drop
or tip over the device, it may damage it.
• The temperature of the product’s body
becomes a little higher after a long period use.
This phenomenon indicates that heat exchange
in normal working mode, thus please do not
let children or anyone who is sensitive of
temperature to touch.
All images provided herein are schematic
drawings and may differ from of real objects.
Installation
Stand installation
Align the holes in the glass stand, base, ring
and bracket and fix these 4 parts by 3 supplied
screws as shown below:
Place the LED TV on a solid flat surface.
Use soft material to place over the front screen
to avoid any damage. Insert the bracket of the
stand assembly into the slit in the bottom part
of the TV cabinet, then fix the stand assembly
with 2 supplied screws as shown below.

5
Connection
Connection
Outdoor Antenna Connection
Use 75Ω coaxial cable plug or 300-75Ω
impedance converter to plug in antenna input
terminal on the rear of the cabinet.
Other connections
• Connect a video source to the Composite
video input jack with RCA cable (not included).
• Connect an audio source to the proper
Audio input jacks (left and right).
• Connect the included DC adapter to the
DC input of this unit.
• When using the unit as a computer screen,
connect the PC to the VGA jack of the unit by
the relevant cable to get the video signal from
the PC. For audio signal from the PC, connect
the left and right jacks of the VGA/Component
audio input of this unit to the audio output jack
of the PC by using relevant connector (not
included).
• If the video source has a HDMI output
jack, you can connect the signal to the unit by
HDMI cable (not included).
• Component input is intended for receiving
component video signal if connected to the
component output of external signal source.
• Connect an external device (e.g., VCR-/
DVD-recorder) to the proper Audio/Video
output jacks of this unit with AV RCA cable (not
included).
• Coaxial output is intended for transmitting
multi-channel sound to an external decoder
(e.g. in 5.1-CH format). RCA cable should be
used for connection.
75 Ohm co-axis cable
TVRF antenna jack
Antenna cable connector

6
Operation
Control elements
Front panel
1
2
1. IR sensor
2. Power indicator
1. POWER button
2. CH+/- buttons
3. VOL+/- buttons
4. MENU button
5. SOURCE button
6. USB port
7. Audio stereo input-2
8. Composite video input-2
9. DC adaptor input
10. HDMI input
11. Component video input
12. Audio input for VGA and component video
13. Coaxial output (SPDIF)
14. Video/audio input-1
15. Composite video/audio output
16. VGA input
17. RF antenna jack
Back panel
1 2 3 4 5
6
7
8
9
10
11
12
13 14 15 16 17

7
Operation
Remote controller (RC)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Index
Size Rev. Hold. Sub
1. button
2. Number buttons
3. INFO button
4. SOURCE button
5. Cursor (UP/DOWN/LEFT/RIGHT) buttons/
OK button
6. TXT button
7. VOL+/VOL- buttons
8. USB button
9. SCALE/SIZE button
10. PICTURE/REV button
11. MTS button/red button
12. Green button
13. POWER button
14. RETURN button
15. MENU button
16. EXIT button
17. INDEX button
18. CH+/CH- buttons
19. FREEZE/SUB button
20. SOUND/HOLD button
21. DEMO button
22. Cyan button/ button
Changing the battery
1. Remove the battery compartment cover
on the back of the RC.
2. Insert the batteries into the battery
compartment making sure that the correct
polarity is observed.
3. Install the cover back.
• Use two AAA batteries for the RC. The RC
should be pointed at remote sensor within 8
meters and within 30 degrees at the left or the
right side.
• Take the battery out of the RC if it is not
used for a long time.
• Do not mix new and used batteries or
different types of batteries. Weak batteries can
leak and severely damage the RC.
• Do not expose the RC to shock, liquids,
and do not place it in an area with high
humidity.
1 2 3

8 9
Operation Operation
General operations
• Press POWER button on the unit or on the
RC to switch on the unit from standby mode.
When the unit is on, press POWER button on
the RC to switch the unit to standby.
• Press VOL- button on the unit or on
the RC repeatedly to decrease the volume;
press VOL+ button on the unit or on the RC
repeatedly to increase the volume.
• Press RETURN button on the RC to select
from the present channel and the previously
displayed channel.
• Press button to cut off sound, press
this button again or adjust volume to resume
sound.
• In TV mode press CH+/CH- buttons on
the RC or on the unit to select previous or next
channel; or press number buttons to enter a
channel number directly.
• Press PICTURE button repeatedly to cycle
through the available video picture modes from
the following types: Standard => Bright => Soft
=> Personal.
• Press SOUND button repeatedly to cycle
through the available sound modes from the
following types: Stereo => Movie => Music =>
News => Personal.
• Press INFO button to display the preset
TV channel information.
• In TV mode press MTS button to switch
NICAM sound mode (not available for some
channels).
• Press SCALE button repeatedly to select
a screen display size from the available list:
4:3/Full/Subtitle/Wide/Zoom/Expand/Original/
Nature. Available aspects may differ for
different signal sources.
• Press FREEZE button to freeze the picture
on or off.
Press SOURCE button, then press cursor
buttons on the RC to select a source from
available source list: TV => YPbPr => PC =>
HDMI => AV1 => AV2. Press OK button to
confirm. You can press USB button to access
Media source mode directly; you can press TV
button to access TV source mode directly.
• Press button to enable/disable Natural
light function. This is to adjust the brightness
of the backlight according to the content of the
inputted signal automatically, so as to optimize
the picture quality and decrease the power
consumption.
• Press DEMO button to display the menu
including E care (Eyes care), E saving (Energy
saving) and E pic (Enhance picture) items.
Press cursor buttons to select an item and
press Ok button to demonstrate the selected
mode of Natural light function. Press DEMO
button or EXIT button to cancel.
It is recommended to demonstrate this
function in full-screen mode.
TELETEXT operations (option)
• Select the TV source mode. Then press
CH-/CH+ buttons to select TV channel in order
to pick up the picture signal of Teletext.
• Teletext button functions are as follows:
TXT: Press this button to enter into Teletext
mode. Press this button to mix the teletext
and current TV signal image. Press this
button again to return to the channel you are
watching.
HOLD: Press this button to stop the move
to the next page. Press this button again to
cancel operation.
INDEX: Press this button to go to the index
page.
SIZE: Press this button to enlarge the top
part of the page. Press this button again to
enlarge the bottom part of the page. Press this
button third time to normal size text page view.
REV. (Reveal): Press this button to reveal
the cancelled information. Press this button
again to cancel the information.
SUB. (Subpage): Press this button to select
sub-page. Input the number of sub-page and
use numeric buttons in the format 0001 for
sub page 1. The teletext will search for the sub
page. Press SUBPAGE button again to exit the
subpage mode.
Red/Green/Yellow/Cyan buttons: Press
these 4 color buttons to access directly to
corresponding color page displayed at the

8 9
Operation Operation
lower parts of teletext screen.
OSD operation
1. Press MENU button to enter the setting
menu displayed on the screen.
2. Press UP/DOWN cursor buttons on the
RC to select setting page.
3. Press OK button on the RC to go to the
parameter list.
4. Press UP/DOWN cursor buttons on the
RC to select a parameter to adjust.
5. Press LEFT/RIGHT cursor buttons on the
RC to adjust the selected parameter.
6. Press MENU button to return to the
previous menu page. Press EXIT button on the
RC to quit the menu.
Some menu items may be in grey color,
in this case they are not adjustable. Pictures
of OSD menu are for reference only; they may
differ from the real screens.
Picture setting page
Picture
Backlight
Picture mode
Scale
Brightness
Contrast
Saturation
Sharpness
Tint
Color temperature
Natural light
Dynamic contrast
• Backlight: adjust the brightness of screen
backlight depending on environmental lighting.
• Picture Mode: Standard/Bright/Soft/
Personal.
• Scale: 4:3/Full/Subtitle/Wide/Zoom/Ex-
pand/Original/Nature.
• Brightness, Contrast, Saturation,
Sharpness, Tint (tint available only for NTSC
system).
• Color temperature: Select color
temperature mode of the picture - Normal/
Warm/Cool.
• Natural light: to adjust the brightness of
the backlight according to the content of the
inputted signal automatically.
• Dynamic contrast: to adjust the image
contrast automatically.
Sound setting page
Sound
Sound mode
Balance
Sound EQ
• Sound mode: News/Music/Movie/Stereo/
Personal.
• Balance: adjust balance between left and
right speaker.
• Sound EQ: adjust the equalizer. Note:
after you adjust the equalizer, the sound mode
will automatically switch to Personal.
Setting page
Setting
DNR
Smart switch
Startup setting
Language
TTX language
Color system
Watch time limit
Time setting
Restore to default
• DNR: Digital noise reduction effect for
reducing the video noise level: Off/On, if the
broadcast signal received is weak.
• Smart switch:
Switch: when the connected external device
is turned on, the TV will automatically switch to
the corresponding source mode.
Display: when the connected external
device is turned on, the TV will show a
prompt message; select OK to switch to the
corresponding source mode.
Off: disable Smart switch function.
• Startup setting: you can select the default
startup picture, captore picture (Logo) and no
startup picture (Off).

10
Operation
• Language: select the language of the
OSD menu.
• TXT Language: select the language of the
teletext subtitles. If selected teletext language
does not correspond to the program language,
subtitles can be diplayed incorrectly.
• Color system: PAL/SECAM/NTSC.
• Watch time limit: set the period of time for
you to watch the TV; when the time elapses,
the TV will switch off automatically. You must
enter the password first (the default password
is 0000; you can also assign your own
password in PW Modify menu). If you forgot
your password, you can use 0432 code.
• Time setting:
Current time: set the current time.
Turnon repeat: Select the mode of TV turn-
on at a specific time (Off/Once/Everyday).
Note: If Off is selected, Turnon time, Wake
source and Wake channel are unavailable.
Turnon time: set the time at which the TV will
turn on automatically.
Wake source: select the source mode to
which the TV will automatically turn on.
Wake channel: select the channel to which
the TV will automatically turn on (available only
if TV is selected as Wake source).
Turnoff repeat: Select the mode of TV turn-off
at a specific time (Off/Once/Everyday). Note: If
Off is selected, Turnoff time is unavailable.
Turnoff time: set the time at which the TV will
turn off automatically.
Sleep time: set the period after which the TV
will audomatically turn off (0 - 120 minutes).
• Restore to default: reset the parameters
to initial factory settings.
Geometry setting (only for PC mode)
Geometry
Auto adjust
H position
V position
AD clock
Phase
• Auto adjust: automatical setting of the
parameters.
• Horizontal Position: adjust horizontal
position of the image.
• Vertical Position: adjust vertical position
of the image.
• AD clock: adjust the image frequency
manually.
• Phase: adjust the phase manually.
Channel setting
Channel
Auto tuning
Intellegent tuning
Manual tuning
Fine-tune
Sound system
Channel edit
• Auto tuning: press OK button to start
automatic search of available channels. To
stop the process press MENU or EXIT button.
• Intellegent tuning: This operation will
keep all the existed channels and add newly
found channels to the end of the channel list.
To stop search, press MENU button; detected
channels will be stored.
• Manual tuning: Press OK button to enter
into manual tuning menu:
Channel: select channel number.
Band: select frequency band (VHFH/UHF/
VHFL).
Frequency: adjust the current frequency step
by step.
• Fine tune: adjust the current frequency
manually to improve the quality of signal if it is
too week.
• Sound system: select the sound system
(DK/BG/I/M).
• Channel edit:
Current Channel: select the current channel
number.
Target Channel: select a target channel for
swapping.
Skip: select Current channel number to be
skipped. Select Skip item and select Yes to
confirm. Now this channel will be skipped when
next/previous channels are selected.
Swap: select Current channel and Target