i.am+ IAM5110 User manual

USER GUIDE




DOTS by i.am+ Bluetooth Headphones IAM5110
Visit PULS.com for support.
English User guide



















Warning letter:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
























1. + Button
2.
• Power On 0 忏/ Pairing / Function Button
3. -
Button
4. LED
indicator
5 Micro
USB(only for charging)
6 USB door
7 Mi c r op hon e
2

3





7



5
6

What’s in the Box.


l DOTS by i.am+ Bluetooth Headphones
l Micro USB charging cable.
l Quick Start Guide
l User Guide
l Warranty





Headphonesoperation



Item Requirement and Description
Power On/Off
l PowerOn:PressandholdtheFunctionbuttonfor3seconds.(releasethe
buttonaftertheblueLEDbright,theredLEDandblueLEDstartflashingmeans
thedeviceenterpairingmode)

l PowerOff:PressandholdtheFunctionbuttonuntiltheredLEDlightup.Red
LEDturnoffmeansthedevicepoweroff
Pairing
l First paring: Press and hold Function button for 3 sec. to power on, earphones
auto-enter pairing mode - LED alternates flashing Red and White.

l To paring with your PULS or phone, go to settings on your PULS or phone,
make sure Bluetooth is switched on.

l The ear-phones appears as “DOTS by i.am+” Select to pair.

l Bluetooth pairing after a successful first pairing:

n Power off then Press and hold Function button for 5 sec. to place earphones
in pairing mode - LED alternates flashing Red and White, mobile phone
search the Bluetooth device to connect the headphones (headphones ID is
“ DOTS by i.am+ ”

n If the earphones are outside Bluetooth range and disconnect from PULS or
your phone, the headphones will automatically try to re-connect. If
reconnection is unsuccessful for more than 5 mins, the headset will power
off.

l Set up use of DOTS headphones with multiple devices such as your PULS and
your smartphone.


1. Pair headphones to PULS or phone 1

2. Turn off the Bluetooth on PULS phone 1, and turn on Bluetooth on
phone 2
3. Search and pair the headset to phone 2

4. Turn on Bluetooth on PULS phone 1 and connect to headset
Charging Open USB door “6” on controller and connect micro USB cable “5”
The headset will power off then enter charging mode - LED signal red while
charging
Solid white when full charge is reached
Using
Headphones
with Aneeda
voice
assistant
Use the Aneeda button on your PULS device to speak to and hear Aneeda on your
headphones
LED
Indication


l LED turned off when headset powered off or not charging

l Power on: white LED on 1s

l Power off: red LED on 1s

l Pairing: LED alternates flashing Red and White
l Connected: white LED 0.1s on/4s off
l Disconnected: white LED 0.1s on 2 times/2s off
l Incoming call: white LED 0.5s on /0.5s off
l Outgoing call: white LED 0.5s on /0.5s off
l Active call: white LED 1s on /1s off
l Music play: white LED 1s on /4s off
l LED is changed from white blinking to Red blinking when battery low

l Charging：The headset will power off and enter charging mode - LED signal red
while charging, Solid white when full charge is reached.
Music Mode Function Status Sound
indication Operation
Volume up Music or phone
call mode No Press volume +
Volume
down Music or phone call mode No Press volume -
Play/Pause Music mode No Short press Function button
Next song Music mode No Double press Function button
Previous
song Music mode No -

Phone call
mode Answer call Incoming call ‘Beep’ sound
once Press Function button 1 time
Reject
incoming call Incoming call No Press and hold Function button for 2 seconds
Hang up
phone call During phone call ‘Beep’ sound one time Press Function button 1 time
Switch call
between
headset and
phone
During phone
call No Double press Function button
Mute During phone
call ‘Beep’ sound two times Fast press volume down button for 2 times
Cancel Mute During phone
call No Fast press volume up button for 2 times
l Incoming call status:

n When mobile phone connected to headset through Bluetooth, mobile phone
will stop music player and play ring tone when have incoming call

n Mobile phone to resume playing music after hanging up phone call

l 3 party phone call:

- Short press Function button to connect the waiting phone call and hang off
current call
- Long press 1s the Function button to connect the waiting phone call and hold
current call. Long press 1s again to switch the two phone call status