i-PRO WV-S85702-F3L User manual

1
About the user manuals
Product documentation is composed of the following documents.
• Installation Guide (this document): Provides information about “Precautions”,
“Precautions for installation” and the installation method.
• Web Guide (Refer to the the link on the following product information website):
Includes installation videos, basic functions, and basic operation methods for this device.
• User manual (Refer to the link on the following product information website):
This section describes the software operating instructions common to each model.
https://i-pro.com/global/en/surveillance/training-support/documentation-database-list
"<Control No.: C****>" used in these documents should be used to search for
information on our technical information website
( https://i-pro.com/global/en/surveillance/training-support/support/technical-information )
and will guide you to the right information.
• Before attempting to connect or operate this product, please read these instructions
carefully and save Important Safety Instructions leaflet for future use.
• microSDXC/ microSDHC/ microSD memory card is described as microSD memory card.
• The external appearance and other parts shown in this manual may differ from the actual product within the
scope that will not interfere with normal use due to improvement of the product.
av0323-0
PGQP3672ZA
https://www.i-pro.com/
Installation Guide
Included Installation Instructions
Network Camera
For professional use only Outdoor use
Model No.
WV-S85702-F3L
WV-S85402-V2L
WV-U85402-V2L
Authorised Representative in EU:
i-PRO EMEA B.V.
Laarderhoogtweg 25, 1101 EB
Amsterdam, Netherlands
i-PRO EMEA B.V. UK Branch
1010 Cambourne Business Park,
Cambridgeshire CB23 6DP
© i-PRO Co., Ltd. 2023

Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries must not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take
them to applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any potential
negative effects on human health and the environment.
For more information about collection and recycling, please contact your local authority.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
Note for the battery symbol (bottom symbol)
This symbol might be used in combination with a chemical symbol. In this case it complies with
the requirement set by the Directive for the chemical involved.
NOTE: This equipment has been tested and
found to comply with the limits for a Class A digi-
tal device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed
and used in accordance with the instruction man-
ual, may cause harmful interference to radio com-
munications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case
the user will be required to correct the interfer-
ence at his own expense.
FCC CAUTION: Changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
Supplier’s Declaration of conformity
Trade name : i-PRO
Model No. : WV-S85702-F3L
WV-S85402-V2L, WV-U85402-V2L
Responsible Party :
i-PRO Americas Inc.
8550 Fallbrook Drive, Suite 200 Houston,
Texas 77064
Support Contact: 1-800-513-5417
For U.S.A.
CAN ICES-3(A)/NMB-3(A)
For Canada
The model number and serial number of this
product may be found on the surface of the
unit.
You should note the model number and serial
number of this unit in the space provided and
retain this book as a permanent record of your
purchase to aid identification in the event of
theft.
Model No.
Serial No.
For U.S.A. This device complies with part 15 of the FCC
Rules.
Operation is subject to the following two condi-
tions : (1) This device may not cause harmful
interference, and (2) this device must accept
any interference received, including interference
that may cause undesired operation.
Méthode d’installation Vis de fixation recommandée
La capacité de traction
minimale requise
Monter directement la caméra vidéo sur la surface
d’installation. M4 x 16 mm {5/8 pouces} / 2 él. 196 N {44 lbf}
Installer la caméra vidéo sur une boîte de groupe/
boîte de jonction double.
Installer la caméra vidéo à l’aide de la platine de
fixation d’installation exclusivement conçue. Se référer au manuel d’utilisation de chaque platine de fixation.
* La longueur de la vis est un exemple lors de l’installation de la caméra au plafond ou sur un mur
robuste d’une épaisseur de 20 mm {25/32 pouces} ou plus.
For U.S.A.
2

 Do not install this product in a restricted or prohibited environment.
Failure to observe this may result in injury, accident, or malfunction due to falling.
Please check the safety precautions common to all models on the website above and the installation
precautions in the Installation Guide.
 Refer installation work to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire, electric
shock, injury,or damage to the product. Be sure to consult the dealer.
 Install the product accurately and securely on an installation surface in accordance with the
installation instructions.
Failure to observe this may cause injury or accidents.
 Take measures of protection against this product falling.
Failure to observe this may cause a drop resulting in injury.
Securely fix the product to the installation surface using screws or anchors. If the fall prevention wire is
included, be sure to install it.
 Stop the operation immediately when something is wrong with this product.
When smoke goes up from the product, the smell of smoke comes from the product, or the exterior of
the product has deteriorated, continued use will cause a fire or fall of the product resulting in injury, or
damage to property.
In this case, turn the power off immediately and contact qualified service personnel for service.
 Conduct periodic inspections.
Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.
Consult the dealer for the inspections.
Be sure to turn off the power before inspection or maintenance.
WARNING:
• Operation of this product in a residential environment could cause radio interference.
Caution: Notice:
• The DC power supply connected to the camera
must be in the same building.
• The network camera is only intended for a
connection to an ethernet or PoE network
without routing to the outside plant.
• This product has no power switch. Be sure
to install disconnect devices such as a circuit
breaker to shut down the main power of power
supplying equipment to this product.
• Before attempting to connect or operate this
product, please read these instructions carefully.
• This product is not suitable for use in locations
where children are likely to be present.
• Do not install this product in locations where
ordinary persons can easily reach.
• This product is a professional equipment.
• For information about screws and other
parts required for installation, refer to the
corresponding section of this document.
: Direct current symbol
Precautions
In order to prevent harm to people and damage to property, it
explains what must be observed without fail. The safety statements
common to all i-PRO network camera models are posted on the
website linked from the twodimensional barcode on the right. Please
be sure to confirm it.
https://i-pro.com/global/en/surveillance/training-support/support/library/safety-instructions
3

Precautions for installation
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures
arising out of improper installation or operation inconsistent with this documentation.
 In order to prevent injury, the product must be securely mounted to an installation surface
according to Installation Guide.
 Installation area for this product
Select an appropriate place for the installation area (such as a strong installation surface) in your particular
environment.
• Make sure that the installation area is strong enough to hold this product, such as a concrete ceiling.
• Install the camera in the foundation area of the architecture or where sufficient strength is assured.
• Do not mount the product on a plaster board or a wooden section because they are too weak. If the
product is unavoidably mounted on such a section, the section shall be sufficiently reinforced.
 Do not place this product in the following places
• Locations where a chemical agent is used such as a swimming pool
• Locations subject to moisture or oil smoke such as a kitchen
• Locations that have a specific environment that is subject to an inflammable atmosphere or solvents
• Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated
• Locations near coasts directly subjected to sea breezes, or locations subject to corrosive gases such
as from hot springs, volcanic regions, etc.
• Locations where the temperature is not within the specified range
• Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This
product is not designed for on-vehicle use.)
• Locations subject to condensation as the result of severe changes in temperature such as near the
outdoor unit of an air conditioner.
• Locations near rubber products containing sulfur (packing, rubber feet, etc.)
 Screw tightening
Do not use an impact driver. Use of an impact driver may damage the screws or cause tightening
excessively.
 About reection of light from outside or IR light
A ghost may appear on the screen depending on the incident angle of external light.
In the case of using the IR light, installation of a camera near a wall may cause reflection of infrared rays
resulting in a part of the screen or the entire screen turning whitish.
• Refer to our technical information website <Control No.: C0109> for image examples and measures to
take.
 Take notice of humidity
Install this product when the humidity is low. If installation is performed when it is raining or in very humid
conditions, the inside may be affected by humidity, causing mist-over inside the dome cover.
 Protection from lightning
When cables are used outdoors, there is a chance that they may be affected by lightning. In such a case,
install a lightning arrestor close to the camera, and make the length of the network cable between the
camera and lightning arrestor as short as possible to prevent the camera from being affected by lightning.
Refer to our technical information website <Control No.: C0121>
 When noise disturbance may happen
Noise may appear in video or audio near a strong electric field from a TV or radio antenna, motors and
transformers, or a strong electric field/magnetic field from a power line (lamp line) of AC100 V or more.
Conduct the power distribution work to keep 1 m {3.28 feet} away from them or conduct the electric
conduit work using metal pipes. (Be sure to make ground connection of the metal pipes.)
 Equipment classication and power source indication label
Refer to the indication label on the bottom side of this unit for the equipment classification, power source,
and other information.
 About static electricity
Before installing or removing this product, be sure to touch metal objects to discharge static electricity
from your body.
4

Specifications
Power source *1: PoE+ (IEEE802.3at compliant)
Power consumption *1:<WV-S85702-F3L><WV-U85402-V2L>
PoE+ DC54V: 350 mA / approx. 18.9W (Class 4 device)
<WV-S85402-V2L>
PoE+ DC54V: 410 mA / approx. 22.2W (Class 4 device)
Operating environment
Ambient operating temperature:
Ambient operating humidity:
–40 °C to +60 °C *2{–40 °F to +140 °F}
(Power On range: –20 °C to +60 °C *2{–4 °F to +140 °F})
10 % to 100 % (no condensation)
Storage environment
Storage temperature:
Storage humidity:
–30 °C to +60 °C {–22 °F to +140 °F}
10 % to 95 % (no condensation)
Waterproof *3: IP67/ IP66 (IEC 60529), Type 4X (UL50E), NEMA 4X compliant
Shock resistance: IK10 (IEC 62262)
Wind resistance: Up to 40 m/s {approx. 89 mph}
Dimensions: 250 mm (W) × 150 mm (H) × 105 mm (D)
{9-27/32 inches (W) × 5-29/32 inches (H) × 4-1/8 inches (D)}
(When using attachment plate only)
Mass: Approx. 1.8 kg{3.97 lbs} (When using attachment plate only)
Finish: Main body: Aluminum die cast, i-PRO white/ Black
Outer fixing screws:
Stainless steel (Corrosion-resistant treatment)
Dome cover: PC resin, Clear
Others: Tamper-resistant enclosure*4
*1 Refer to our technical information website <Control No.: C0106> for further information about Power
source and Power consumption information.
*2 When using with the IR LED light constantly lit, the upper limit of the operating temperature range is
+50 °C {+122 °F}.
*3 Only when installation work is properly performed according to the Installation Guide and appropriate
waterproof treatment is performed.
*4 Component that has a structure on which the screws that are accessible after installation cannot be
screwed or unscrewed using an ordinary screwdriver.
Optional accessories
The latest information →Technical information website “Accessory Selector”
<Control No.: C0501>
Troubleshooting
Before requesting service, refer to “Troubleshooting” of Web Guide. Then, confirm the trouble.
5

Standard accessories
Important Safety Instructions ............................. 1 pc.
Attachment plate*11×
Bit 1× (Hex wrench,
screw size 6.35 mm
{1/4 inches} T20)
Grommet 2×
(of them, 1 for spare)
Sun shade 1× Conduit cover 1× Conduit base 1×
Template 1× Cable cover 1× RJ45 cap1×
RJ45 Ethernet cable for
easy kitting*11×
*1 The attachment plate and the RJ45 Ethernet cable for easy kitting are attached to the camera.
Other items that are needed (not included)
⿟Mounting screws
Installation method
Recommended
screw*1
Minimum pull-out
strength*2
Directly mount the camera onto the installation surface M4 × 16 mm
{5/8
 inches} × 4pcs.*3196 N {44lbf}
Mount the camera to a two-gangbox/junction box.
Mount the camera using the exclusively designed mount
bracket.
Refer to the operating instructions of each
bracket.
*1 Select screws according to the material of the location that the camera will be mounted to. In this
case, wood screws and nails should not be used.
*2 This value indicates the minimum pull-out strength required value per screw. For information about the
min-imum pull-out strength, refer to our technical information website <Control No.: C0120>.
*3 The screw length is an example when installing the camera on a robust installation surface with a
thickness of 20mm {25/32inches} or more.
⿟Ethernet cable with RJ45 plug (category 5e or better, straight, all 4 pairs (8pins))
6

Parts and functions
Installation Procedure
: Lights
: Blinks
: Lights off
• User manual [Indicator]
All LEDs forced to turn off
The female thread for conduit
is compliant with ANSI NPSM
(parallel pipe threads) 3/4 or
ISO 228-1 (parallel pipe
threads) G3/4.
Attachment plate
Enclosure
Dome cover
Camera
section
Fixing position for conduit
Conduit base
Conduit cover
Sun shade
Cable cover
See Web Guide
7

INITIAL SET button
LINK indicator
ACT indicator
RJ45 network connector
microSD slot
• Refer to the “Initialize” in the Web Guide.
• Use a microSD memory card dedicated to i-PRO cameras.
<WV-S85702-F3L>
SD ERROR indicator
<WV-S85402-V2L><WV-U85402-V2L>
SD ERROR/ AF indicator
SD MOUNT indicator
Terminal for I/O cable
(WV-QCA501A: optional accessory)
SD ON/OFF button
Clamper
8

Step 1 Preparations
Remove the enclosure
Remove the RJ45 Ethernet cable for easy kitting
Installed
auxiliary wire
Inside
Bit
(accessory)
9

 Remove the camera from the attachment plate
■When not wiring on the side
10

 When using an I/O cable (WV-QCA501A)
Inside
Outside
②
①
11

 When using a microSD
①
②A click sound is heard
 When using a sun shade
②
①
Inside
12

FRONT
Step 2
* 1 When drilling a hole through the installation surface.
* 2 When using the conduit
This plate can be fixed at the following seven screw positions depending on the condition of the
installation surface. Use the same mounting holes from A to J.
Length Width
A 85 mm{3-11/32 inches} (85.7 mm{3-3/8 inches}) 85 mm{3-11/32 inches} (85.7 mm{3-3/8 inches})
C 83.5 mm{3-9/32 inches} (83.3 mm{3-9/32
inches})
46 mm{1-13/16 inches} (47.6 mm{1-7/8
inches})
D 63 mm{2-15/32 inches} 63 mm{2-15/32 inches}
E* – 83.5 mm{3-9/32 inches}
F 46 mm{1-13/16 inches} (47.6 mm{1-7/8 inches}) 83.5 mm{3-9/32 inches} (83.3 mm{3-9/32
inches})
G* 83.5 mm{3-9/32 inches} –
* When installing to a single switch box, fix with two fixing screws (M4: locally procured).
144 mm
{5-11/16 inches}
87 mm
{3-7/16 inches}
32 mm {1-1/4 inches}*2
244 mm {9-5/8 inches}
Cable access hole*1
ø50 mm {2 inches}
 When mounting the camera onto the wall
FRONT
FRONT
FRONT
FRONT
13

 When drilling a hole through the installation surface
 When using the conduit
Minimum pull-out strength:
196 N {44 lbf}/ per 1 pc.
M4 screw (4 pcs.)
(locally procured)
Minimum pull-out strength:
196 N {44 lbf}/ per 1 pc.
M4 screw (6 pcs.)
(locally procured)
M4 screw (locally procured)
M4 screw (locally procured)
①①
②
②
②
②
14

Step 3
①
①
②
②
15

Step 4
Grommet
(accessory)
Reuse
RJ45 Ethernet
Category 5e or better, straight, 4 pairs (8 pins)
<100 m {328 feet}
80 mm
{3-5/32 inches}
RJ45 cap
(accessory)
Center
ø5 mm to ø8.5 mm
{ø3/16 inches to ø11/32 inches}
Inside
Outside
Inside
Outside
16

 Ground wire
 RJ45 Ethernet cable
①
②
Inside
Outside
RJ45 Ethernet
Category 5e or better,
straight, 4 pairs (8pins)
<100m {328feet}
Technical information
website “Countermeasure
for Lightning Surge”
<Control No.:C0121>
M3 × 6 mm {1/4 inches}
Recommended tightening torque:
0.69 N·m {0.51 lbf·ft}
Ground wire
(locally procured)
17

 When using an I/O cable (WV-QCA501A)
Approx. 20 mm
{25/32 inches}
Approx. 20 mm
{25/32 inches}
Stretch the waterproof tape by
about twice the length to use.
Waterproof tape
(WV-QCA501A accessory)
• This cable is not to be used. Apply waterproofing also to this cable as well as other cables.
I/O cable
WV-QCA501A
(optional accessory)
Audio in (White)
Audio out (Black)
EXT I/O
< 1 m {3.28 feet} (Mic)
< 10 m {32.8 feet} (Line)
< 10 m {32.8 feet}
4P alarm cable
(WV-QCA501A accessory) GND (Black)
ALARM IN3 (Gray)
ALARM IN2 (Red)
ALARM IN1 (Green)
18

Step 5
Make sure the camera is firmly fixed.
Wire processing
clamper
19

Step 6 →
Turn the power on (PoE+).
Wi-Fi
WV-S85702X_XXXXXXX
WV-X1111_XXXXXXXX
WV-X2222_XXXXXXXX
Wi-Fi USB adapter
(locally procured)
●Technical information website
“About using Wi-Fi USB adapter”
<Control No.: C0114>
URL :
http://192.168.12.10
●If access to http://192.168.12.10 fails,
try http://10.0.0.10.
SSID :
“Product No._Serial No. of the camera”
Password :
“cam_” + “Serial No. of the camera”
Web Guide
“Configure Easy installation”
20