I-View CZ-537-10X User manual

Rev. 3-2-2012
CZ-53X Series IR Night Vision
Fast Dome Cameras
Available Models:
CZ-537-10X 520TVL 10X PTZ Camera
CZ-533-4 650TVL Fixed 4mm PT Camera
CZ-533-8 650TVL Fixed 8mm PT Camera
CZ-533-12 650TVL Fixed 12mm PT Camera
CZ-531-4 520TVL Fixed 4mm PT Camera
CZ-531-8 520TVL Fixed 8mm PT Camera
CZ-531-12 520TVL Fixed 12mm PT Camera

Contents
1 Instruction......................................................................................................1
1.1 Safety Instructions.............................................................................1
1.2 Warnings............................................................................................1
2 Feature...........................................................................................................2
2.1 Product Features................................................................................2
2.2 Specifications ....................................................................................3
3 Functions.......................................................................................................4
4 Installation Instruction...................................................................................5
5 Operation.......................................................................................................7
5.1 Power On Self -Check.......................................................................8
5.3 Camera Lens control..........................................................................8
5.3.1 Zoom.....................................................................................8
5.3.2 Focus.....................................................................................8
5.3.3 Iris.........................................................................................9
5.4 Setting the preset ...............................................................................9
6 How to Use OSD Menu.................................................................................9
6.2 Main Menu........................................................................................9
6.2.1 System Information.............................................................11
6.2.2 Address Setting....................................................................11
6.2.3 Motion.................................................................................12
6.2.4 Patterns................................................................................13
6.2.5 Camera Setup ......................................................................14
6.2.6 Cruise Setting......................................................................24
6.2.7 IR Setting ............................................................................24
6.2.8 Display Setup ......................................................................25
6.2.9 Restore Factory Default.......................................................25
6.2.10 Reboot System...................................................................25
7 Trouble Shooting .........................................................................................26
8 Fast Control Chart .......................................................................................27
Appendix I DIP Switch Setup.........................................................................27

1
1 Instruction
These series of products can be widely used in intelligent building, bank
security, urban roads, airport terminals and bus stations, and also are able to
satisfy various demands from any square and activities occasion.
1.1 Safety Instructions
Make sure to read the user manual before using the product.
Always confirm to national and local safety codes during installation.
Only qualified and experienced person can carry on this installation and
maintenance.
Use reliable tools, otherwise may lead to dangerous incidents.
Please check the space and toughness of the site before installing. It
should be able to bear 4 times the weight of the dome and its
accessories.
Protocol and baud rate auto detected; RS485 non-polarity to control.
Note: Should restart the dome after changed the baud rate and 485
connection method.
1.2 Warnings
Do not install this speed dome in hazardous places where combustible or
explosive materials are stored or used.
Do not place the machine on shaking desk.
Make sure no uncertain object or fluid substances get inside the unit.
Do not turn power on before finishing installation.
Do not disassemble any part of the items.
Use soft towel to clean the down cover when necessary, do not use
caustic detergent.
To protect CCD, avoid facing the camera directly to the strong light.
To prevent damage, do not drop the unit or subject to strong shock or
vibration.

2
2 Feature
2.1 Product Features
* OSD menu;
* Auto flip;
* Proportional zoom;
* Day & night function;
* RS485 non-polarity to control;
* 254 presets, support lens preset;
* Protocol and baud rate auto detected;
* Compatible 38*38 CCD with fixed focus lens;
* Pan Speed: 0.5°~40°/ sec, Tilt Speed: 0.5°~20°/ sec;
* 360° pan rotation, 90° auto flip, auto rotation 180 °, no blind monitor;
* Soft address enables to set up the address and number of the camera;
* Unique appearance of the radiator structure, the heat of IR lights gives off
by heat sink install outside, makes the life of IR lights and camera module
longer;
* Multiple scans: frame scan (speed adjustable); 4 patterns; 3 tours; 360°
random scan; 360° continuous scan; parking action; etc.
* Support Sony, Samsung protocol camera module, special protocol could be
customized.

3
2.2 Specifications
Model IR Mini Variable Speed Dome Camera
Help Selection Ceiling
Power Supply DC12V/2A 50Hz/60Hz
Power ≤15W
Pan Speed 0.5°~40°/ sec
Tilt Speed 0.5°~20°/ sec
Pan Range 360°continuous
Tilt Range 0°~90° auto flip
Preset 254
Pan Scan
frame scan; 360° random scan; 360° continuous scan;
Pattern 4
Cruise 3
OSD Menu Chinese/English
IR Illumination ON/OFF (option)
IR Distance ≥20m
Baud Rate 2400bps,4800bps,9600bps auto adaptive
Protocol PELCO-D, PELCO-P
Communication RS485
Address 255
Work Temperature -10°C~40°C
Camera Module
Support 10X Samsung, Sony camera module,
compatible 38*38 CCD with fixed focus lens.

4
3 Functions
3.1 SettingAddress Code
Setting address code before using the dome camera, it could be setup by the
dip-switch or soft address.
3.2 Zoom/ Rotation Auto Match Technology
The camera can adjust automatically pan tilt speed according to the zoom far
or near, make sure easier to operate manual motion detection.
3.3 Auto Pan
The operator pulls the lens to the bottom, and still holds the joystick, at this
time, the lens level up 90° flip after auto pan rotation 180°, can watch directly
the back of scene in order to achieve 180° continuous vertical monitoring.
3.4 Setting or Calling preset
The dome camera supports 254 presets.
3.5 Lens Control
(1) Zoom Control
User could adjust zoom far or near by keyboard or matrix system, in order to
get the full picture or the fine view.
(2) Focus Control
The default of dome camera is auto focus, zoom, the camera lens will
automatically focus the center of the screen scene, maintaining a clear image;
in special cases the user can manually focus, to achieve the desired image
effect.
When in manual focus state, to resume the auto-focus, use the joystick can be
restored to auto-focus. Besides, you can send a special control command or
call any preset to restore auto-focus.
3.6 Iris Control
User can control the keyboard to adjust the iris manually to get the brightness
of the picture.

5
3.7 Auto Cruise
The preset #99 is programmed to be recalled in sequence. This feature is
called auto cruise. Call preset #99 to start preset #1 to #20 cruises, call preset
#88, start preset #1~#10, call preset #89, start preset #11~#20 cruise.
3.8 Pattern
A pattern is a saved, repeating, series of pan, tilt, zoom and preset functions that
can be recalled with a command from a controller or automatically by a
programmed function (alarm action or park action or power-up action). Call
preset #84, #85, #86, #86, and #87 to call the saved pattern.
3.9 Continuous Scan
Achieve Continuous scan by calling preset #98 or park action.
3.10 Random Scan
Achieve random scan by calling preset #92 or park action.
4 Installation Instruction
4.1 Installation
A. Fixed the ceiling installation board with supplied screws. The board
dimension as shows:

6
B. Install the dome camera as shows:
4. 2 System Connection

7
Power supply: DC12V/2A
RS485: Output RS485 signal, connect the camera.
BNC Connector: Output Video Signal.
4. 3 Dip Switch Setup
Dip Switch as follows:
Notice: Dip Switch Address Setup see appendix I
5 Operation
Note: The manual will refer to our CCTV tester to explain how to operate
and control the camera.

8
5.1 Power On Self -Check
When power on, the camera moves automatically from pan range to tilt range,
after movement, pull the lens to the nearest and then to the farthest, make sure
the camera is running in normal.
After the display information disappeared, press direction key “Left” and
“right” twice, the camera could auto detected the baud rate,protocol and 485
polarity of the control device, then the camera could be controlled in normal.
Remark: After the camera auto detected the baud rate, protocol and 485
polarity of the control device, but when changed the baud rate and 485
polarity of the control device, restart the camera, then the camera could
auto detected again and be controlled in normal.
5.2 Control the Direction of Camera
Using “UP, DOWN, LEFT, RIGHT” direction key control PTZ Camera to a
desired position.
5.3 Camera Lens control
5.3.1 Zoom
Adjust the lens distance to enlarge or downsize the image for best effect or
wide-angle effect.
♦Using “ZOOM IN / TELE” key to enlarge the images.
♦Using “ZOOM OUT/ WIDE” key to downsize the images.
5.3.2 Focus
Adjust definition of the object of scene
♦Press “Focus Far” key to shorten the distance of far scene.
♦Press “Focus Near” key to shorten the distance of near scene.
PROTOCOL: AUTO
BAUD RATE: AUTO
ADDRESS: 1

9
5.3.3 Iris
Press “Iris Open” key to adjust the brightness.
5.4 Setting the preset
Following the steps to set preset:
(1) Select Camera.
(2) Control joystick, Proportion Key and Iris Key to adjust the picture.
(3) Press preset No. + PRESET, save the parameter of the picture.
5.4 Calling the preset
Following the steps to review preset:
Press designated preset + CALL
6 How to Use OSD Menu
6.1 Basic operation of Main menu
♦Go Preset #95 enter into main menu.
♦Using “Iris open” and “Iris close” to confirm or exit main menu.
♦Using “UP/DOWN” keys or joystick to move cursor to sub-menu, press
“Iris open” to enter into menu.
♦Using “UP/DOWN” keys or joystick to move cursor to the function and
press “Iris open” to choose the function.
♦Using “UP/DOWN” keys or joystick to set up and press “Iris open” to
save.
♦Move the cursor to “BACK” and press “Iris open” to back to main
menu.
6.2 Main Menu
Call preset #95 enter the main menu:

10
<SYSTEM INFORMATION>: Shows system information.
<ADDR SETTING>: Select and setup Soft/Hard address.
<MOTION>: Setup for motion related settings.
<PATTERNS>: Setup for Patterns.
<CAMERA>: Configure Camera related functions and data.
<CRUISE SETTING>: Setup presets scan.
<IR SETTING>: Setting IR ON/OFF SENS.
<DISPLAY SETUP>: Enable / Disable of OSD display on main screen.
<RESTORE FACTORY DEFAULT>: Restore factory settings.
<REBOOT SYSTEM>: Reboot the system.
MAIN MENU
SYSTEM INFORMATION
ADDR SETTING
MOTION
PATTERNS
CAMERA
CRUISE SETTING
IR SETTING
DISPLAY SETUP
RESTORE FACTORY DEFAULT
REBOOT SYSTEM
EXIT

11
6.2.1 System Information
<COM>: Shows current Baud rate.
<ADDRESS>: Shows current Camera ID for PTZ control, 0~255.
<SOFTWARE VERSION>: Shows current software version of camera.
Notice: The system information can not be changed.
6.2.2 Address Setting
<ADDR TYPE>: Choose the address type (Hard/Soft Add), when you
choose soft type, the user can setup the address by remote access.
<ADDR SOFT>: Setup soft address. The camera ID can be set from
0~255.
<ADDR HARD>: Setup hard address. It can be changed by DIP Switch.
Notice: Please reboot the dome camera after reset the camera ID.
ADDR SETTING
ADDR TYPE HARD
ADDR SOFT 1
ADDR HARD 1
BACK
EXIT
SYSTEM INFORMATION
COM 2400, N, 8, 1
ADDRESS 1
SOFTWARE VERSION V5.2
BACK
EXIT

12
6.2.3 Motion
Frame Scan
<SET SCAN POSITION>: Set up scan range between two positions
(Left/Right extreme position).
<CLEAR FRAME SCAN>: Deletes frame scan.
6.2.3.1 Set Scan Position
(1) Move the cursor to <SET SCAN POSITION> and enter below interface.
(2) Move the cursor to choose the extreme position of preset by using
“Left/Right” keys or joystick of your controller, then press “Iris Open” to
SET FRAME SCAN
LEFT LIMIT POSITION
IRIS OPEN TO CONTINUE
FRAME SCAN
SET SCAN POSITION
CLEAR FRAME SCAN
FRAME SCAN SPEED 16
BACK
EXIT
MOTION
FRAME SCAN
POWER UP NONE
PARK TIME 15S
PARK ACTION NONE
BACK
EXIT

13
enter below interface:
6.2.3.2 Clear Frame Scan
Move the cursor to “Clear Frame Scan” to enter, then press “Iris Open” to
delete the extreme positions.
6.2.4 Patterns
<PATTERN NUMBER>: Set Pattern number (1~4).
<PROGRAM PATTERN>: Pattern scan program.
<CLEAR CURRENT PATTERN>: Deletes data in current pattern.
PATTERNS
PATTERN NUMBER 1
PROGRAM PATTERN
CLEAR CURRENT PATTERN
CLEAR ALL PATTERN
BACK
EXIT
SET FRAME SCAN
RIGHT LIMIT POSITION
IRIS OPEN TO CONTINUE
CLEAR FRAME SCAN
IRIS OPEN TO CONTINUE

14
6.2.5 Camera Setup
We are using Samsung SDM-100P camera to explain below operation.
Notice: “Up/Down” keys for option, “Left/Right” keys for details, “Iris
Open” for sub-menu.
<CAMERA LABEL>: press “Iris Open” to enter sub-menu and edit
camera label.
Using cursor to select the letter, then press “Iris Open” key to save the setup.
CAMERA LABEL
ABCDEFGHIJKLMNO
PQRSTUVWXYZ a b c d
e f g h I j k l m no p q r s
t u v w x y z01234567
89 ( ) < > - / # *!? , .
Clean Position Exit
MAIN MENU
CAMERA LABEL OFF
WHITE BALANCE AUTO
BLC OFF
AUTO DETECTION
OFF
FOCUS
EXPOSURE
ADDITIONAL MENU
BACK
EXIT

15
<WHITE BALANCE>:
WB Mode: Auto Trace / Manual / Auto
(1) Auto Trace : Indoor/Outdoor, The camera can automatically adjust ambient
light from1800K~10500K(Indoor: 3000~10,500K; Outdoor: 1,800~10,500K),
to ensure the most nature image effect.
(2) Manual: Close auto WB, adjust Red and Blue level manually.
Red adjust range: 0~100 Blue adjust range: 0~100
(3) Auto BW: This mode is the most accurate and reliable for most places.
<BACKLIGHT COMPENSATION>
Backlight: High/Middle/Low/Off
<MOTION DETECTION>
Match the Alarm sensor input to one of preset positions. If an external sensor
is activated, camera will move to corresponding preset position when this item
is predefined.
MANUAL WB
RED 30…|..……….
BLUE 41…..…|…….
EXIT
AUTO TRACE WB
AUTO TRACE WB MODE OUTDOOR
EXIT

16
Alarm: On/Off Region：1~4 Region Mode: On / Off
<FOCUS>
♦<MODE>: Auto, Manual, One-off Auto focus. Press “Iris Open” to enter
sub-menu
One-off auto focus: Once the image zoom changes, the camera will
automatically focus and fix the status till the image change again.
Notice: Do not use Auto Focus under the below conditions.
The target is too dark (such as black clothes or curtains).
FOCUS
MODE AUTO
ZOOM TRACE MODE ON
ZOOM TRACE SPEED FAST
DIGITAL ZOOM ON
SHOW ZOOM OFF
INITIAL ZOOM POSITION OFF
LENS INITIALIZATION
EXIT
MOTION DETECTION
ALARM OFF
SELECT REGION 1
REGION MODE ON
TOP 20…|..……….
BOTTOM 25….…|…….
LEFT 20…|.……….
RIGHT 40….……|….
EXIT

17
The target is very smooth( like car surface)
The brightness contrast of the target is not very clear.
Too strong high light or back light.
Too high contrast.
Some shade in front of the target.
①Auto mode setup:
Using the direction keys to enlarge or downsize, press “Iris/Open” key to
back.
②One-off Auto focus and Manual focus Adjustment:
♦<ZOOM TRACE MODE>:
Manual Focus: Off. Auto and One-off Auto Focus: On / Off.
♦<ZOOM TRACE SPEED>: Fast/Slow.
♦<DIGITAL ZOOM>: On / Off, range: X2~X10.
♦<SHOW ZOOM>: On / Off.
♦<INITIAL ZOOM POSITION>: Using direction keys to move the
SETUP ZOOM
↑ZOOM IN ↓ZOOM OUT
BACK: PRESS “SET” KEY.
SETUP ZOOM
↑ZOOM IN ↓ZOOM OUT
←NEAR →FAR
BACK: PRESS “SET” KEY.
DIGITAL ZOOM
DIGITAL ZOOM X2
EXIT

18
cursor to “On”, then press “Iris Open” to set up.
Zoom Range: X1~X10
♦<LENS INITIALIZATION>: press “Iris open/Set” key to initialize the
lens.
♦<EXPOSURE>:
<BRIGHTNESS>: Brightness Range: 0~100.
<IRIS>: Auto/ Manual. Press “Iris Open” to enter into manual setup.
If the number of iris is set to higher, the image will be brighter.
<SHUTTER > :Shutter Mode: Flicker / Manual / Auto
The shutter speed ofAnti-flash is 1/100 (NTSC), 1/120 (PAL)
Manual mode setting (PAL):2X、4X、6X、8X、10X、12X、14X、16X、
MANUAL IRIS
IRIS 100….………|
EXIT
EXPOSURE
BRIGHTNESS 25….…|…….
IRIS AUTO
SHUTTER ——
AGC OFF
SSNR OFF
SENS-UP OFF
EXIT
INITIAL ZOOM POSITION
INITIAL ZOOM POSITION X1
EXIT