i3 International IP09CP User manual

Thank you for purchasing i3 International’s IP09CP PoE extender (sold in pairs). Use IP09CP as a point-to-point PoE (Power over
Ethernet) extender to power IP devices and to carry IP signal for distances of up to 984 feet (300 meters) using existing coaxial cable
infrastructure. Use with i3’s line of IP cameras and PoE switches and/or U12 NVR (built-in PoE).
INSTALLATION
PoE over Coax Extender, 1000 ft IP09CP
User Manual
i3-TRNG-ACCESSORIES-IP09CP.indd
Rev. 220913
FEATURES
• Signal extension up to 984 ft (300 m) over coaxial cable.
• Provides up to 90W power to a remote PoE device.
• Power source from either a PoE switch or an external power
adapter.
• Bandwidth up to 100Mbps.
• Supports full duplex and half duplex mode and Auto MDI/
MDI-X switching.
• Built-in 30kV ESD, 40A EFT, and 30A surge at RJ45 side.
• Note: Ax85 supports distances up to 328 ft (100 m) only.
Mode 1 (Auto Mode, default) is recommended for all IP
devices.
PoE Cameras &
other IP devices
IP09CPT
(Transmitter)
i3 INTERNATIONAL INC. 1.866.840.0004
www.i3international.com
1 2 3 4 5
67 8
REGULATORY NOTICES (FCC CLASS A)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits of a Class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
984 ft 300 m6.5 ft 2 m 6.5 ft 2 m
PoE Switch /
U12 NVR
CONNECTORS
1. DC Power Connector. Connect to DC48~56V adapter if
connecting to a non-PoE switch.
2. Power LED Indication. Indicates device power status. See Table 1.
3. Status Indication. Indicates RJ45 mode. See Table 3.
4. Status Indication. Indicates BNC mode. See Table 4.
5. DIP Switch. Mode selector. See Tables 5, 6.
6. RJ45 Connector. Connect to the PoE IP device. See Table 7.
7. PoE LED Indication. Indicates PoE connection status. See Table 2.
8. BNC Connector. Connect to the second IP09CP device using the
RG59 cable, 984 ft (300 m) or less. The link speed is up to 100
Mbps.
Figure 2. IP09CP front and back panels, parts description.
Note, connectors that are not labeled are reserved/not in use.
Figure 1. IP09CP connection diagram.
RG59 / RG6U coaxial
IP09CPR
(Receiver)
PACKAGE CONTENTS
1. IP09CPT (Transmitter) x1. Connect to the IP camera.
2. IP09CPR (Receiver) x1. Connect to the PoE switch.
3. Plastic Anchor x8
4. Round Head Screw (Tapping Type) x8
Figure 3. IP09CP front and back panels

i3-TRNG-ACCESSORIES-IP09CP.indd
SPECIFICATION
IP09CPR
(Receiver)
IP09CPT
(Transmitter)
Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3bw 100BASE-T1 Ethernet
IEEE 802.3 N-Way Auto-Negotiation
IEEE 802.3x Full Duplex Operation & Flow Control
IEEE 802.3az Energy Efficient Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3bt Power over Ethernet Plus Plus
Bandwidth 10/100 Mbps
Max.
Transmission
Distance
10Mbps @ 984 ft (300 m)
100Mbps @ 328 ft (100 m)
Ports & Interfaces
Input 1 x 75Ω BNC 1 x RJ45
Output 1 x RJ45 1 x 75Ω BNC
Power
Interface
1 x (5.5 x 2.1mm) DC
Jack
1 x (5.5 x 2.1mm) DC
Jack
Power
Power Supply 48 ~ 56V Regulated 12 ~ 56V Regulated
Power
Consumption 1W 1W
Environmental specifications
Operation 32-185 °F (0-85 °C);
Storage -4-185 °F (-20-85 °C);
Humidity ≤ 95%
Physical Characteristics
Dimensions 2⅝”x 5 5/16”x 1 1/16” (67 x 135 x 27mm)
Weight 0.45 lbs (205 g) 0.47 lbs (215 g)
i3 INTERNATIONAL INC. 1.866.840.0004
www.i3international.com
IP09CP. PoE over Coax Extender, 1000 ft
QUICK START GUIDE
Green ON Green OFF LED “Breathing”
Power ON Power OFF Power Saving
Table 1. Power Status LED
Blue ON Blue OFF
PoE ON PoE OFF
Table 2. PoE Status LED
Blue ON Blue OFF LED Blinking
Long
Distance
Unlinked or
Ethernet 100Base-T1
Table 3. Port 1 (RJ45) Mode Status LED
Blue ON Blue OFF LED Blinking
Long
Distance
Unlinked or
Ethernet 100Base-T1
Table 4. Port 2 (BNC) Mode Status LED
Mode SW1 SW2 SW3 SW4
Auto Mode (Default), recommended OFF ↑OFF ↑OFF ↑OFF ↑
Auto Mode with EEE ON ↓OFF ↑OFF ↑OFF ↑
100Mbps ON ↓ON ↓ON ↓ON ↓
10Mbps, not recommended OFF ↑ON ↓ON ↓ON ↓
Table 5. Dip Switch Mode Selector
Auto Mode / Default (Recommended):
Auto-Negotiation, automatically sets up the
link speed and transmission protocol.
Auto Mode with EEE: Energy-efficient
Ethernet-based on Auto-Mode
SW# Function OFF ↑ON ↓
1 Link Speed 10Mbps 100Mbps
2 Ethernet Disable Enable
3 100BASE-T1 Disable Enable
4 Long Distance Disable Enable
Table 6. Advanced Mode, Manual Link Speed and Mode Dip Switch Configuration
PIN Color PoE Mode A
(PoE Switch)
PoE Mode B
(PoE Injector)
1 White Orange TX+ / PoE + TX+
2 Orange TX- / PoE + TX-
3 White Green RX+ / PoE - RX+
4 Blue PoE+
5 White Blue PoE+
6 Green RX- / PoE - RX-
7 White Brown PoE-
8 Brown PoE-
PIN LAYOUT
Table 7. RJ45 Pin Layout
ACT Download &
Documentation
Scan this QR code or visit ftp.i3international.com for
Annexxus Configuration Tool (ACT) installation and
additional documentation.
Contact our Technical Support team at: 1.877.877.7241
or [email protected] if you have any
questions or concerns regarding camera installation or if
you require software services or support.