Iai Cm-080ge User manual

CM-080GE

CB-080GE

CM-080GE-RA

CB-080GE-RA

Digital Monochrome / Color

Progressive Scan GigE Vision Camera

Document Version: Version 2.1

CMB-080GE_Ver.2.1_Feb2013

User's Manual

CM-080GE/CM-080GE-RA / CB-080GE/CB-080GE-RA

- 2 -

Notice

The material contained in this manual consists of information that is proprietary to JAI Ltd.,

Japan and may only be used by the purchasers of the product. JAI Ltd., Japan makes no

warranty for the use of its product and assumes no responsibility for any errors which may

appear or for damages resulting from the use of the information contained herein. JAI Ltd.,

Japan reserves the right to make changes without notice.

Company and product names mentioned in this manual are trademarks or registered

trademarks of their respective owners.

Warranty

For information about the warranty, please contact your factory representative.

Certifications

CE compliance

As defined by the Directive 2004/108/EC of the European Parliament and of the Council, EMC

(Electromagnetic compatibility), JAI Ltd., Japan declares that CM-080GE, CB-080GE, CM-

080GE-RA and CB-080GE-RA comply with the following provisions applying to its standards.

EN 61000-6-3 (Generic emission standard part 1)

EN 61000-6-2 (Generic immunity standard part 1)

FCC

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Warning

Changes or modifications to this unit not expressly approved by the party

responsible for FCC compliance could void the user’s authority to operate the

equipment.

CM-080GE /CM-080GE-RA

Supplement

The following statement is related to the regulation on “ Measures for the Administration

of the control of Pollution by Electronic Information Products “ , known as “ China RoHS “.

The table shows contained Hazardous Substances in this camera.

mark shows that the environment-friendly use period of contained Hazardous

Substances is 15 years.

嶷勣廣吭並㍻

嗤蕎嗤墾麗嵎賜圷殆兆各式根楚燕

功象嶄鯖繁酎慌才忽佚連恢匍何〆窮徨佚連恢瞳麟半陣崙砿尖一隈〇



云恢瞳ゞ嗤蕎



嗤

墾麗嵎賜圷殆兆各式根楚燕〃泌和



桟隠聞喘豚㍉

窮徨佚連恢瞳嶄根嗤議嗤蕎嗤墾麗嵎賜圷殆壓屎械聞喘議訳周和音氏窟伏翌

亶賜融延、窮徨佚連恢瞳喘薩聞喘乎窮徨佚連恢瞳音氏斤桟廠夛撹冢嶷麟半

賜斤児繁附、夏恢夛撹冢嶷鱒墾議豚㍉。

方忖仝15々葎豚㍉15定。

CB-080GE / CB-080GE-RA

Supplement

The following statement is related to the regulation on “ Measures for the Administration

of the control of Pollution by Electronic Information Products “ , known as “ China RoHS “.

The table shows contained Hazardous Substances in this camera.

mark shows that the environment-friendly use period of contained Hazardous

Substances is 15 years.

嶷勣廣吭並㍻

嗤蕎嗤墾麗嵎賜圷殆兆各式根楚燕

功象嶄鯖繁酎慌才忽佚連恢匍何〆窮徨佚連恢瞳麟半陣崙砿尖一隈〇



云恢瞳ゞ嗤蕎



嗤

墾麗嵎賜圷殆兆各式根楚燕〃泌和



桟隠聞喘豚㍉

窮徨佚連恢瞳嶄根嗤議嗤蕎嗤墾麗嵎賜圷殆壓屎械聞喘議訳周和音氏窟伏翌

亶賜融延、窮徨佚連恢瞳喘薩聞喘乎窮徨佚連恢瞳音氏斤桟廠夛撹冢嶷麟半

賜斤児繁附、夏恢夛撹冢嶷鱒墾議豚㍉。

方忖仝15々葎豚㍉15定。

CM-080GE/CM-080GE-RA / CB-080GE/CB-080GE-RA

- 3 -

Table of Contents

JAI GigE® Vision Camera operation manuals ........................................................ - 5 -

Introduction ............................................................................................. - 5 -

Before using GigEVision cameras..................................................................... - 5 -

Software installation................................................................................... - 5 -

Camera operation ...................................................................................... - 6 -

1. General ............................................................................................... - 6 -

2. Camera nomenclature .............................................................................. - 6 -

3. Main Features ........................................................................................ - 7 -

4. Locations and Functions............................................................................ - 8 -

4.1. CM-080GE and CB-080GE ................................................................................- 8 -

4.2. CM-200GE-RA/CB-200GE-RA .............................................................................- 9 -

4.3. Rear panel indicator. ................................................................................... - 10 -

5. Pin Assignment......................................................................................- 11 -

5.1. 12-pin Multi-connector (DC-in/GPIO/Iris Video)..................................................... - 11 -

5.2. Digital Output Connector for Gigabit Ethernet ...................................................... - 11 -

6. Input and output interface.......................................................................- 12 -

6.1. GPIO interface ........................................................................................... - 12 -

6.1.1. LUT (Cross point switch ) input and output setting.......................................... - 12 -

6.1.2. 12-bit Counter ...................................................................................... - 13 -

6.1.3. Pulse Generators................................................................................... - 13 -

6.2. Optical Interface ........................................................................................ - 14 -

6.2.1 Recommended External Input circuit diagram for customer .............................. - 15 -

6.2.2 Recommended External Output circuit diagram for customer............................ - 15 -

6.2.3 Optical Interface Specifications................................................................. - 16 -

6.3. Inputs and outputs table.............................................................................. - 16 -

6.4. Configuring the GPIO module .......................................................................... - 17 -

6.4.1. Input/Output Signal Selector.................................................................... - 17 -

6.5. Examples of the pulse generator configuration ................................................... - 17 -

6.5.1 Setting screen of the pulse generator ......................................................... - 17 -

6.5.2 GPIO Plus PWC shutter ........................................................................... - 18 -

6.5.3 Internal Trigger Generator....................................................................... - 19 -

7. Image output signal ...............................................................................- 20 -

7.1. Output image............................................................................................. - 20 -

7.2. Vertical Binning (CM-080GE/CM-080GE-RA only). ................................................. - 20 -

7.3. Digital Video Output (Bit Allocation)................................................................. - 21 -

7.3.1 Bit Allocation (Pixel Format / Pixel Type) – CM-080GE/CM-080GE-RA................... - 21 -

7.3.2 Bit Allocation (Pixel Format / Pixel Type) – CB-080GE/CB-080GE-RA.................... - 22 -

7.3.2.4 GVSP_PIX_BAYRG10 “Bayer RG10”........................................................... - 23 -

7.4. CB-080GE/CB-080GE-RA Bayer filter................................................................. - 23 -

7.5. Image timing ............................................................................................. - 24 -

7.5.1 Horizontal timing.................................................................................. - 24 -

7.5.2 Vertical timing..................................................................................... - 24 -

7.5.3 Partial Scanning ................................................................................... - 25 -

7.5.4 Vertical binning.................................................................................... - 26 -

7.5.5 Auto Iris Lens video output (12-pin Hirose connector) ..................................... - 27 -

8. Network configuration ...........................................................................- 28 -

8.1. GigEVision Standard interface......................................................................... - 28 -

8.2. Equipment to configure the network system....................................................... - 28 -

8.2.1 PC .................................................................................................... - 28 -

8.2.2 Cables ............................................................................................... - 28 -

8.2.3 Network card (NIC)................................................................................ - 28 -

8.2.4 Hub................................................................................................... - 29 -

8.3. Recommended Network Configurations ............................................................. - 29 -

8.3.1 Guideline for network settings................................................................. - 29 -

CM-080GE/CM-080GE-RA / CB-080GE/CB-080GE-RA

- 4 -

8.3.2 Video data rate (network bandwidth) ......................................................... - 30 -

8.3.3 Note for setting packet size..................................................................... - 30 -

8.3.4 Calculation of Data Transfer Rate.............................................................. - 30 -

8.3.5 Simplified calculation (Approximate value) .................................................. - 31 -

8.3.6 Note for 100BASE-TX connection ............................................................... - 31 -

8.4. GigE camera connecting examples ................................................................... - 32 -

8.4.1 Using a switching hub for 1 port................................................................ - 32 -

8.4.2 Connecting a camera to each port of a multi-port NIC..................................... - 32 -

8.4.3 The data transfer for multiple cameras....................................................... - 33 -

9. Functions and operations........................................................................- 35 -

9.1. Basic functions........................................................................................... - 35 -

9.2. Electronic Shutter .................................................................................. - 35 -

9.3. Auto-detect LVAL-sync / a-sync. accumulation ............................................... - 36 -

10. Operation Modes.................................................................................- 38 -

10.1. The functions related to GenICam SFNC 1.3 ...................................................... - 38 -

10.2. Operation Modes ....................................................................................... - 41 -

10.2.1 Continuous operation ........................................................................... - 41 -

10.2.2 Edge Pre-select Trigger Mode.................................................................. - 42 -

10.2.3 Pulse Width Control Trigger Mode ............................................................ - 44 -

10.2.4 Reset Continuous (RCT) trigger mode........................................................ - 46 -

10.2.5 Sequential Trigger Mode (Pre-select trigger ) ............................................. - 47 -

10.2.6 Delayed Readout Mode (Pre-Select).......................................................... - 49 -

10.2.7 OB transfer Mode ................................................................................ - 50 -

10.2.8 Operation Mode and Functions matrix...................................................... - 51 -

11. JAI control tool ..................................................................................- 52 -

11.1. About GenICamTMSFNC1.3 ............................................................................ - 52 -

11.2. JAI SDK Ver.1.3......................................................................................... - 52 -

11.3. Examples of camera operation ...................................................................... - 53 -

11.3.1 Generic cautions for operation................................................................ - 53 -

11.3.2 Connection of camera(s) ....................................................................... - 53 -

11.3.3 Camera setting level ............................................................................ - 53 -

11.4. Input and Output settings ............................................................................ - 54 -

11.4.1 Interfacing with external devices............................................................. - 54 -

11.4.2 Setting of input and output .................................................................... - 54 -

11.4.3 Setting the image size .......................................................................... - 55 -

11.4.4 Acquisition of the image........................................................................ - 56 -

11.4.5 How to look at XML file......................................................................... - 56 -

11.4.6 Feature Tree Information ...................................................................... - 56 -

11.4.7 Feature Properties (Guru)..................................................................... - 57 -

12. External Appearance and Dimensions..........................................................- 61 -

12.1. CM-080GE and CB-080GE.............................................................................. - 61 -

12.2. CM-080GE-RA and CB-080GE-RA..................................................................... - 62 -

13. Specifications.....................................................................................- 63 -

13.1. Spectral response ....................................................................................... - 63 -

13.2. Specification table...................................................................................... - 64 -

14. Appendix..........................................................................................- 66 -

14.1. Precautions.............................................................................................. - 66 -

14.2. Typical Sensor Characteristics....................................................................... - 66 -

14.3. Caution when mounting a lens on the camera.................................................... - 66 -

14.4. Caution when mounting the camera................................................................ - 67 -

14.5. Exportation.............................................................................................. - 67 -

14.6. References .............................................................................................. - 67 -

Change History.........................................................................................- 68 -

User's Record...........................................................................................- 69 -

CM-080GE/CM-080GE-RA / CB-080GE/CB-080GE-RA

- 5 -

JAI GigE® Vision Camera operation manuals

To understand and operate this JAI GigE® Vision camera properly, JAI provides the following

manuals.

User’s manual (this booklet) Describes functions and operation of the hardware

JAI SDK & Control Tool User Guide Describes functions and operation of the Control Tool

JAI SDK Getting Started Guide Describes the network interface

User’s manual is available at www.jai.com

JAI SDK & Control Tool User Guide and JAI SDK Getting Started Guide are provided with the

JAI SDK which is available at www.jai.com.

Introduction

GigEVision is a standard interface which uses Gigabit Ethernet for machine vision applications.

It was developed primarily by AIA (Automated Imaging Association) members. GigEVision is

capable of transmitting large amounts of uncompressed image data through an inexpensive

general purpose LAN cable over long distances.

GigEVision also supports the GenICamTM standard which is maintained by the EMVA (European

Machine Vision Association). The purpose of the GenICam standard is to provide a common

program interface for various machine vision cameras. By using GenICam, cameras from

different manufactures can seamlessly connect in one platform.

For details about the GigEVision standard, please visit the AIA web site,

www.machinevisiononline.org and for GenICam, the EMVA web site, www.genicam.org.

JAI GigEVision cameras comply with both the GigEVision standard and the GenICam standard.

Before using GigE Vision cameras

All software products described in this manual pertain to the proper use of JAI GigEVision

cameras. Product names mentioned in this manual are used only for the explanation of

operation. Registered trademarks or trademarks belong to their manufacturers.

To use the JAI SDK, it is necessary to accept the “Software license agreement” first.

This manual describes necessary equipment and the details of camera functions.

Software installation

The JAI GigE Vision SDK & Control Tool can be downloaded from the JAI web site at

www.jai.com. The JAI SDK is available for Windows XP and Vista, 32-bit and 64-bit.

For the details of software installation, please refer to the “Getting Started Guide” supplied

on the JAI SDK download page.

CM-080GE/CM-080GE-RA / CB-080GE/CB-080GE-RA

- 6 -

Camera operation

1. General

This manual covers the digital monochrome progressive scan camera CM-080GE/CM-

080GE-RA and color progressive scan camera CB-080GE/CB-080GE-RA

The CM-080GE/CM-080GE-RA/CB-080GE/CB-080GE-RA is a new addition to JAI GigE Vision

compliant camera series. Both the monochrome version CM-080GE/CM-080GE-RA and the

color version CB-080GE/CB-080GE-RA provide a frame rate of 30.08 frames/second at full

resolution. Using vertical binning (CM-080GE/CM-080GE-RA only) and partial scan provides

higher frame rates.

The 1/3" CCD with square pixels offers a superb image quality. The high-speed shutter

function and asynchronous random trigger mode allows the camera to capture high quality

images of fast moving objects.

The color version CB-080GE/CB-080GE-RA, based on CCD sensor with primary RGB Bayer

mosaic filter, outputs raw Bayer images. Host-based color interpolation is required to display

or save color images.

The CM-080GE/CM-080GE-RA/CB-080GE/CB-080GE-RA also comply with the GenICam standard

and contains an internal XML files that is used to describe the functions/features of the

cameras. For further information about GigE®Vision standard, please go to

www.machinevisiononline.org and about GenICamTM, please go to www.emva.org.

As an application programming interface, JAI provides an SDK (Software Development Kit).

This SDK includes GigEVision Filter Driver,JAI control tool, software documentation and code

examples.

The JAI SDK can be downloaded from www.jai.com

The latest version of this manual can be downloaded from www.jai.com

For camera revision histories, please contact your local JAI distributor.

2. Camera nomenclature

The standard camera composition consists of a camera main body and a C-mount protection

cap.

The camera is available in the following versions:

CM-080GE / CM-080GE-RA

Where Cstands for "Compact" family, Mstands for "Monochrome", 080 represents the

resolution "800 thousand pixel", and GE stands for "GigE Vision" interface, RA stands for Right

Angle type.

CB-080GE / CB-080GE-RA

Where Cstands for "Compact" family, Bstands for "Bayer mosaic color", 080 represents the

resolution "800 thousand pixel", and GE stands for " GigE Vision" interface, RA stands for Right

Angle type

CM-080GE/CM-080GE-RA / CB-080GE/CB-080GE-RA

- 7 -

3. Main Features

•Member of Compact series, covering VGA to UXGA resolution

•1032 (h) x 778 (v) 4.65 µm square pixels for effective output image

•1/3” progressive scan – monochrome and Bayer mosaic color versions

•High frame rate of 30.08 frames/second with full resolution in continuous operation

•30 frames/second with external trigger and full resolution

•+24dB Gain and noise reduction circuit built-in

•Increased frame rate with vertical binning (CM-080GE/CM-080GE-RA only) and

partial scan

•Exposure time from 84μs to 2 sec. using Pulse Width Control trigger mode

•Programmable exposure from 84μs to 33 ms in Full Frame scan

•Sequencer trigger mode for on-the –fly change of gain, exposure and ROI

•Edge Pre-select and Pulse width trigger mode

•LVAL-synchronous/-asynchronous operation (auto-detect)

•Auto iris lens video output allows a wider range of light (Can be Selected by DIP

switch )

•GigE Vision Interface with 10 or 8-bit output

•Programmable GPIO with opto-isolated inputs and outputs

•Can be connected with 100BASE-TX

•Right Angle types are available as CM-080GE-RA and CB-080GE-RA

•Comprehensive software tools and SDK for Windows XP/Vista

Note: CM/CB-080GE and CM/CB-080GE-RA can be connected with 100BASE-TX.

However, due to the limited bandwidth (100Mbps), the described

specifications such as frame rate, minimum trigger interval and so on cannot

be satisfied for 100BASE-TX connection.

CM-080GE/CM-080GE-RA / CB-080GE/CB-080GE-RA

- 8 -

4. Locations and Functions

4.1. CM-080GE and CB-080GE

Serial No.

FCC seal

Caution seal

① ②

　③

④

⑤

　⑥

⑦

⑧

POWER / TRIG

GigE

⑨

Lens mount C-mount (Note *1)

CCD sensor 1/3 inch CCD sensor

12-pin connector DC +12V to +24 power and GPIO interface

RJ-45 Gigabit Ethernet connector with threaded holes for

thumbscrews

LED Indication for power and trigger input

LED GigE Network condition: LINK

LED GigE Network condition: ACT

Holes for RJ-45 thumbscrews When an RJ-45 connector with thumbscrews is used,

remove the two screws located above and below the

Ethernet connector (Note*2)

Mounting holes M3 depth 3.5mm for tripod mount plate (Note*3)

*1) Note: Rear protrusion on C-mount lens must be less than 10.0mm.

*2) Note: When a RJ-45 cable with thumbscrews is connected to the camera, please do not

excessively tighten screws by using a screw driver. The RJ-45 receptacle on the

camera might get damaged. For security, the strength to tighten screws is less than

0.147 Newton meter (Nm). Tightening by hand is sufficient in order to achieve this.

*3) Note: The depth of holes is 3.5mm. When the tripod adapter plate MP-40 or MP-41 is used,

use the attached screws. If installing the camera directly, please do not use screws

longer than 3.5mm.

Fig. 1. Locations (CM-080GE / CB-080GE)

This manual suits for next models

Table of contents

Other IAI Security Camera manuals

IAI

IAI AG-7000 User manual

IAI

IAI SP-20000C-USB User manual

IAI

IAI GO-5100M-USB User manual

IAI

IAI GO-2401M-PGE User manual

IAI

IAI GO-2400M-PMCL User manual

IAI

IAI AT-200GE User manual

IAI

IAI SP-20000M-CXP2 User manual

IAI

IAI AM-200GE User manual

IAI

IAI GO-2400M-USB User manual

IAI

IAI AT-140GE User manual

Popular Security Camera manuals by other brands

ADEMCO

ADEMCO RapidDome Owners Operating & Installation Guide

EverFocus

EverFocus EBA2880 user manual

Honeywell

Honeywell OptiCAM-IR Installation and setup guide

Uniq

Uniq UC-600 user manual

OPTICOM

OPTICOM NVD-120-S datasheet

Steren

Steren CCTV-221 instruction manual

Arm Electronics

Arm Electronics C420BCDNVFIR Features

Eneo

Eneo PLD-2036PTZ installation guide

Axis

Axis AXIS M20 Series installation guide

Panasonic

Panasonic KX-HCM230 operating instructions

COP-USA

COP-USA CC15NV-SL Specifications

Active Silicon

Active Silicon HARRIER H.264 quick start guide

Motorola

Motorola Avigilon 1.3C-H5SL-BO1-IR installation guide

INSTEON

INSTEON 2864-232 user manual

Wisenet

Wisenet XNB-6002 quick start guide

Axis

Axis M5525-E user manual

Vitek

Vitek VTC-IR62NZ922 user guide

Panasonic

Panasonic WV-SF342 Specifications

IAI CM-080GE User manual

Popular Security Camera manuals by other brands