IBM 28L2234 User manual

2X/4X/24X CD-ReWritable
Internal IDE Option Kit
OP T IONS

Note: If you are using this product in the United States, Canada, or Puerto Rico, be sure to read the information under Appendix F,
“Product warranty and notices” on page 3-31 before using this information and the product it supports.
For all other countries, the warranty terms and conditions applicable in the country of purchase are available from IBM or your reseller.
First Edition (January 1999)
The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law: INTERNATIONAL
BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. IBM may make improvements and/or changes in the product(s) and/or the program(s) described in this publication
at any time.
This publication was developed for products and services offered in the United States of America. IBM may not offer the products, services, or features discussed
in this document in other countries, and the information is subject to change without notice. Consult your local IBM representative for information on the
products, services, and features available in your area.
Requests for technical information about IBM products should be made to your IBM reseller or IBM marketing representative.
Copyright International Business Machines Corporation 1999. All rights reserved.
Note to U.S. Government Users — Documentation related to restricted rights — Use, duplication or disclosure is subject to restrictions set forth in GSA ADP
Schedule Contract with IBM Corp.

Contents
Safety: Read first . . . . . . . . . . . . . . . . . . . . . . . v
Product registration . . . . . . . . . . . . . . . . . . . . . . vi
About this book ........................ vi
Part 1: Quick installation guide ................................................. 1-1
Part 2: User’s guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Before you begin ....................... 2-1
Protecting the drive after installation ............ 2-1
Using CD-R and CD-RW discs ................ 2-1
Using the drive controls and connectors ........... 2-2
Front view of the drive .................... 2-2
Rear view of the drive ..................... 2-2
Using the drive to record files on CDs ............ 2-3
Using CD handling precautions ............... 2-4
Caring for a CD ........................ 2-4
Loading a CD ......................... 2-5
Manually ejecting a CD .................... 2-6
Playing an audio CD ...................... 2-6
Using a data CD ........................ 2-8
Copyright IBM Corp. 1999 iii

Part 3: Appendixes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Appendix A. Safety Information . . . . . . . . . . . . . . 3-1
Appendix B. Product specifications . . . . . . . . . . . . 3-11
Appendix C. Customizing device driver configuration
settings . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Appendix D. Problem solving . . . . . . . . . . . . . . . 3-20
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
Additional help . . . . . . . . . . . . . . . . . . . . . . . 3-28
Appendix E. Help and service information ........ 3-28
Step 1: Problem solving . . . . . . . . . . . . . . . . . . . 3-29
Step 2: Preparing for the call ................ 3-29
Step 3: Placing the call to IBM ............... 3-29
Step 4: Placing the call to computer and BIOS manufacturers 3-30
Appendix F. Product warranty and notices ........ 3-31
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . 3-34
Electronic emission notices ................. 3-34
iv IBM 2X/4X/24X CD-ReWritable Internal IDE Option Kit

Safety: Read first
v

Product registration
Thank you for purchasing OPTIONS by IBM. Please take a few
moments to register your product and provide us with information that
will help IBM to better serve you in the future. Your feedback is
valuable to us in developing products and services that are important
to you, as well as in developing better ways to communicate with you.
Register your option on the IBM Web site at:
http://www.pc.ibm.com/register
IBM will send you information and updates on your registered product
unless you indicate on the Web site questionnaire that you do not want
to receive further information.
About this book
This manual contains information on the IBM 2X/4X/24X
CD-ReWritable Internal IDE Option Kit. It is divided into the
following parts:
Part 1: Quick installation guide
This section contains product and software descriptions,
installation requirements, and abbreviated installation
instructions.
Part 2: User’s guide
This section contains device handling precautions, detailed
operating instructions, and CD handling instructions.
Part 3: Appendixes
This section contains safety, product specifications, device
driver configuration settings, service, warranty and notice
information.
Note: The illustrations in this manual might be slightly different from
your hardware.
vi IBM 2X/4X/24X CD-ReWritable Internal IDE Option Kit

Part 1: Quick installation guide
This guide contains installation instructions in an abbreviated form. If
you are knowledgeable about IDE products and experienced in
installing options, use these instructions to quickly install your
CD-ReWritable drive. For detailed operating instructions, go to “Part
2: User’s guide” on page 2-1. For problem-solving information, go
to Appendix D, “Problem solving” on page 3-20.
Product description
The IBM 2X/4X/24X CD-ReWritable Drive can write and read
CD-ReWritable (CD-RW) and CD-Recordable (CD-R) discs, and can
read mass-produced stamped CDs. As a result, the drive is compatible
with Multi-Read (MR) CD-ROM and DVD-ROM drives that can read
CD-RW discs and other media types, and with older non-MR
CD-ROM drives that can read only CD-R and CD-ROM discs.
The drive writes to CD-RW and CD-R discs at different speeds. The
drive can write to a CD-RW disc at up to two times the standard
CD-ROM speed, recording data at up to 300 KB1 per second. At this
rate, the drive can record approximately 650 MB2 of information on a
CD-RW disc in about 36 minutes. The drive can write to a CD-R disc
at up to four times the standard CD-ROM speed, recording data at up
to 600 KB per second. At this rate, the drive can record
approximately 650 MB of information on a CD-R disc in about 18
minutes. The drive can also read data at up to 24 times the standard
CD-ROM speed, or 3600 KB per second.
Note: To use the drive’s CD-recording function, you must install the
Easy CD Creator/DirectCD software (included) for Microsoft
Windows 98, Windows 95, or Windows NT 4.0. For more
information on the Easy CD Creator/DirectCD software, see
“Software description” on page 1-2.
The IBM 2X/4X/24X CD-ReWritable Drive can be installed only in a
computer that uses the integrated drive electronics (IDE) or the
enhanced IDE architecture.
In addition to this book, the option kit includes:
CD-ReWritable drive
Two audio cables
Four mounting screws (M3 x 5 mm, slotted)
IDE cable
Two faceplates for use with certain systems
1KB equals approximately 1024 bytes when referring to data transfer speeds.
2MB equals approximately 1000000 bytes when referring to storage capacity.
Copyright IBM Corp. 1999 1-1

Blank CD-RW disc
Blank CD-R disc
Easy CD Creator/DirectCD software package
IBM 2X/4X/24X CD-ReWritable Drive Option Diskette
Laser Safety Guide for CD-ROMs
Contact your place of purchase if an item is missing or damaged. Be
sure to retain your proof of purchase. It might be required to receive
warranty service. See Appendix E, “Help and service information” on
page 3-28 for technical support information.
Software description
The Easy CD Creator/DirectCD software CD contains programs that
work with Windows 98, Windows 95, and Windows NT 4.0 or later.
You can use the programs with your CD-ReWritable drive to create
audio and data CDs, to copy CDs, and to make jewel case inserts or
CD labels.
The IBM 2X/4X/24X CD-ReWritable Drive Option Diskette contains
device drivers for Windows 98, Windows 95, Windows NT 4.0,
Windows 3.x, OS/2, and DOS that enable you to access the drive as a
CD-ROM drive in DOS mode. The diskette also includes an audio
CD-player program for DOS and a diagnostic program.
Note: The software included in this option kit does not enable the
drive’s CD-recording capabilities with DOS, Windows 3.x, or
OS/2 operating systems.
Installation requirements
To install the CD-ReWritable drive you must have:
Documentation
You will need the documentation that comes with your computer,
operating system, or IDE bus adapter if the adapter is separate from
the computer.
Required hardware
You must have the following hardware.
IBM computer or compatible computer with an Intel
Pentium processor and 16 MB3 RAM (random-access
memory)
3.5-inch, 1.44 MB or 2.88 MB diskette drive
IDE bus adapter
Your computer must have an IDE port on the system board or on
an IDE bus adapter. If the interface cable connectors in your
computer have 40 pins, your computer uses the IDE architecture. If
3When referring to memory storage capacity, MB means approximately 1000000 bytes; total user-accessible capacity may vary depending on operating
environment.
1-2 IBM 2X/4X/24X CD-ReWritable Internal IDE Option Kit

you are not sure about your IDE bus adapter, see the documentation
that comes with your computer.
IDE cables and connectors
The IDE cables connect the IDE port on the system board, or on an
IDE adapter, to your IDE storage devices. IDE storage devices are
hard disk drives, CD-ROM drives, and tape drives.
If your computer has one IDE port, you can attach a maximum of
two devices, as shown in the following illustration.
If your computer has two IDE ports (one IDE cable on each port),
you can attach up to four devices (two devices on each cable).
If your IDE cables have only one connector, you can replace one of
the cables with the two-connector IDE cable that comes with this
option package.
If you are attaching the CD-ReWritable drive to the same port as
another device, such as a hard disk drive or tape drive, you might
need to change the configuration of that device. For more
information, refer to the documentation that comes with the device.
You cannot install some devices, such as a high speed tape drive,
on the same port as a CD-ReWritable drive.
Power connector
You will need an unused power connector on a cable coming from
the computer power supply in order to provide power to the drive.
If all power cables are in use, purchase a dc Y-connector (available
at many electronic stores) and split a connection to provide power
for more devices.
CD-ReWritable drive mounting
You can install the CD-ReWritable drive in a vertical or horizontal
5.25-inch mounting bay. You might need both a flat-blade and a
Phillips-head screwdriver for the installation.
Part 1: Quick installation guide 1-3

Installing the drive
The instructions in this section are general guidelines that apply to
most computers. For specific information on installing a drive in your
computer, see the documentation that comes with your computer.
Step 1. Opening the computer
1. Turn off the computer and all attached devices.
2. Unplug from the electrical outlets all cables for your computer
and attached devices.
It is now safe to open your computer.
For specific information about opening your computer, see the
documentation that comes with your computer.
Step 2. Unpacking the drive
Follow these steps when you unpack the drive.
1. Do not open the antistatic bag until you are ready to install the
drive. Static electricity can damage the drive and other computer
components.
2. Touch your hand and the inner conductive surface of the antistatic
bag containing the drive to an unpainted metal surface on the
computer for two seconds. This drains static electricity from the
bag and your body.
3. Before handling the drive, ground yourself by touching an
unpainted surface on the computer. Ground yourself again after
leaving and returning to your work area.
4. Always handle the drive by its edges. Do not touch any exposed
printed circuitry, components, or connector pins.
5. While installing the drive, avoid all unnecessary handling. Rough
handling can damage the components inside the drive housing.
6. If you must put the drive down, place the antistatic bag on a flat
padded surface, such as a magazine, and place the drive on the
bag.
Step 3. Setting the configuration jumpers
You can configure your drive as Master 1, Slave 2, or Cable
Select 3, as shown.
1-4 IBM 2X/4X/24X CD-ReWritable Internal IDE Option Kit