IBM PureFlex System Instruction Manual

PureFlex System
Installing and configuring IBM PureFlex
System
GI11-9880-02


PureFlex System
Installing and configuring IBM PureFlex
System
GI11-9880-02


Note
Before using this information and the product it supports, read the information in “Safety notices” on page v and “Notices”
on page 23 and read the information in the safety and environmental notices included with the system.
This edition applies to the IBM PureFlex System and to all subsequent releases and modifications until otherwise
indicated in new editions.
© Copyright IBM Corporation 2012, 2013.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.

Contents
Safety notices ............v
Installing and configuring the system . . 1
Scenario: Installing the IBM PureFlex System . . . 3
Performing tasks associated with the 7953-94X rack . 4
Removing the IBM Storwize V7000 shipping brackets 6
Verifying that the IBM Storwize V7000 control
enclosure is cabled between racks .......12
Connecting power cords ..........13
Performing a verification check ........15
Completing the installation ......21
Notices ..............23
Trademarks ..............24
Electronic emission notices .........24
Class A Notices ............24
Class B Notices ............28
Terms and conditions ...........31
© Copyright IBM Corp. 2012, 2013 iii

iv PureFlex System: Installing and configuring IBM PureFlex System

Safety notices
Safety notices may be printed throughout this guide:
vDANGER notices call attention to a situation that is potentially lethal or extremely hazardous to
people.
vCAUTION notices call attention to a situation that is potentially hazardous to people because of some
existing condition.
vAttention notices call attention to the possibility of damage to a program, device, system, or data.
World Trade safety information
Several countries require the safety information contained in product publications to be presented in their
national languages. If this requirement applies to your country, safety information documentation is
included in the publications package (such as in printed documentation, on DVD, or as part of the
product) shipped with the product. The documentation contains the safety information in your national
language with references to the U.S. English source. Before using a U.S. English publication to install,
operate, or service this product, you must first become familiar with the related safety information
documentation. You should also refer to the safety information documentation any time you do not
clearly understand any safety information in the U.S. English publications.
Replacement or additional copies of safety information documentation can be obtained by calling the IBM
Hotline at 1-800-300-8751.
German safety information
Das Produkt ist nicht für den Einsatz an Bildschirmarbeitsplätzen im Sinne§2der
Bildschirmarbeitsverordnung geeignet.
Laser safety information
IBM®servers can use I/O cards or features that are fiber-optic based and that utilize lasers or LEDs.
Laser compliance
IBM servers may be installed inside or outside of an IT equipment rack.
© Copyright IBM Corp. 2012, 2013 v

DANGER
When working on or around the system, observe the following precautions:
Electrical voltage and current from power, telephone, and communication cables are hazardous. To
avoid a shock hazard:
vConnect power to this unit only with the IBM provided power cord. Do not use the IBM
provided power cord for any other product.
vDo not open or service any power supply assembly.
vDo not connect or disconnect any cables or perform installation, maintenance, or reconfiguration
of this product during an electrical storm.
vThe product might be equipped with multiple power cords. To remove all hazardous voltages,
disconnect all power cords.
vConnect all power cords to a properly wired and grounded electrical outlet. Ensure that the outlet
supplies proper voltage and phase rotation according to the system rating plate.
vConnect any equipment that will be attached to this product to properly wired outlets.
vWhen possible, use one hand only to connect or disconnect signal cables.
vNever turn on any equipment when there is evidence of fire, water, or structural damage.
vDisconnect the attached power cords, telecommunications systems, networks, and modems before
you open the device covers, unless instructed otherwise in the installation and configuration
procedures.
vConnect and disconnect cables as described in the following procedures when installing, moving,
or opening covers on this product or attached devices.
To Disconnect:
1. Turn off everything (unless instructed otherwise).
2. Remove the power cords from the outlets.
3. Remove the signal cables from the connectors.
4. Remove all cables from the devices.
To Connect:
1. Turn off everything (unless instructed otherwise).
2. Attach all cables to the devices.
3. Attach the signal cables to the connectors.
4. Attach the power cords to the outlets.
5. Turn on the devices.
(D005)
DANGER
vi PureFlex System: Installing and configuring IBM PureFlex System

Observe the following precautions when working on or around your IT rack system:
vHeavy equipment–personal injury or equipment damage might result if mishandled.
vAlways lower the leveling pads on the rack cabinet.
vAlways install stabilizer brackets on the rack cabinet.
vTo avoid hazardous conditions due to uneven mechanical loading, always install the heaviest
devices in the bottom of the rack cabinet. Always install servers and optional devices starting
from the bottom of the rack cabinet.
vRack-mounted devices are not to be used as shelves or work spaces. Do not place objects on top
of rack-mounted devices.
vEach rack cabinet might have more than one power cord. Be sure to disconnect all power cords in
the rack cabinet when directed to disconnect power during servicing.
vConnect all devices installed in a rack cabinet to power devices installed in the same rack
cabinet. Do not plug a power cord from a device installed in one rack cabinet into a power
device installed in a different rack cabinet.
vAn electrical outlet that is not correctly wired could place hazardous voltage on the metal parts of
the system or the devices that attach to the system. It is the responsibility of the customer to
ensure that the outlet is correctly wired and grounded to prevent an electrical shock.
CAUTION
vDo not install a unit in a rack where the internal rack ambient temperatures will exceed the
manufacturer's recommended ambient temperature for all your rack-mounted devices.
vDo not install a unit in a rack where the air flow is compromised. Ensure that air flow is not
blocked or reduced on any side, front, or back of a unit used for air flow through the unit.
vConsideration should be given to the connection of the equipment to the supply circuit so that
overloading of the circuits does not compromise the supply wiring or overcurrent protection. To
provide the correct power connection to a rack, refer to the rating labels located on the
equipment in the rack to determine the total power requirement of the supply circuit.
v(For sliding drawers.) Do not pull out or install any drawer or feature if the rack stabilizer brackets
are not attached to the rack. Do not pull out more than one drawer at a time. The rack might
become unstable if you pull out more than one drawer at a time.
v(For fixed drawers.) This drawer is a fixed drawer and must not be moved for servicing unless
specified by the manufacturer. Attempting to move the drawer partially or completely out of the
rack might cause the rack to become unstable or cause the drawer to fall out of the rack.
(R001)
Safety notices vii

CAUTION:
Removing components from the upper positions in the rack cabinet improves rack stability during
relocation. Follow these general guidelines whenever you relocate a populated rack cabinet within a
room or building:
vReduce the weight of the rack cabinet by removing equipment starting at the top of the rack
cabinet. When possible, restore the rack cabinet to the configuration of the rack cabinet as you
received it. If this configuration is not known, you must observe the following precautions:
– Remove all devices in the 32U position and above.
– Ensure that the heaviest devices are installed in the bottom of the rack cabinet.
– Ensure that there are no empty U-levels between devices installed in the rack cabinet below the
32U level.
vIf the rack cabinet you are relocating is part of a suite of rack cabinets, detach the rack cabinet from
the suite.
vInspect the route that you plan to take to eliminate potential hazards.
vVerify that the route that you choose can support the weight of the loaded rack cabinet. Refer to the
documentation that comes with your rack cabinet for the weight of a loaded rack cabinet.
vVerify that all door openings are at least 760 x 230 mm (30 x 80 in.).
vEnsure that all devices, shelves, drawers, doors, and cables are secure.
vEnsure that the four leveling pads are raised to their highest position.
vEnsure that there is no stabilizer bracket installed on the rack cabinet during movement.
vDo not use a ramp inclined at more than 10 degrees.
vWhen the rack cabinet is in the new location, complete the following steps:
– Lower the four leveling pads.
– Install stabilizer brackets on the rack cabinet.
– If you removed any devices from the rack cabinet, repopulate the rack cabinet from the lowest
position to the highest position.
vIf a long-distance relocation is required, restore the rack cabinet to the configuration of the rack
cabinet as you received it. Pack the rack cabinet in the original packaging material, or equivalent.
Also lower the leveling pads to raise the casters off of the pallet and bolt the rack cabinet to the
pallet.
(R002)
(L001)
(L002)
viii PureFlex System: Installing and configuring IBM PureFlex System

(L003)
or
All lasers are certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for class
1 laser products. Outside the U.S., they are certified to be in compliance with IEC 60825 as a class 1 laser
product. Consult the label on each part for laser certification numbers and approval information.
CAUTION:
This product might contain one or more of the following devices: CD-ROM drive, DVD-ROM drive,
DVD-RAM drive, or laser module, which are Class 1 laser products. Note the following information:
vDo not remove the covers. Removing the covers of the laser product could result in exposure to
hazardous laser radiation. There are no serviceable parts inside the device.
vUse of the controls or adjustments or performance of procedures other than those specified herein
might result in hazardous radiation exposure.
(C026)
Safety notices ix

CAUTION:
Data processing environments can contain equipment transmitting on system links with laser modules
that operate at greater than Class 1 power levels. For this reason, never look into the end of an optical
fiber cable or open receptacle. (C027)
CAUTION:
This product contains a Class 1M laser. Do not view directly with optical instruments. (C028)
CAUTION:
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following
information: laser radiation when open. Do not stare into the beam, do not view directly with optical
instruments, and avoid direct exposure to the beam. (C030)
CAUTION:
The battery contains lithium. To avoid possible explosion, do not burn or charge the battery.
Do Not:
v___ Throw or immerse into water
v___ Heat to more than 100°C (212°F)
v___ Repair or disassemble
Exchange only with the IBM-approved part. Recycle or discard the battery as instructed by local
regulations. In the United States, IBM has a process for the collection of this battery. For information,
call 1-800-426-4333. Have the IBM part number for the battery unit available when you call. (C003)
Power and cabling information for NEBS (Network Equipment-Building System)
GR-1089-CORE
The following comments apply to the IBM servers that have been designated as conforming to NEBS
(Network Equipment-Building System) GR-1089-CORE:
The equipment is suitable for installation in the following:
vNetwork telecommunications facilities
vLocations where the NEC (National Electrical Code) applies
The intrabuilding ports of this equipment are suitable for connection to intrabuilding or unexposed
wiring or cabling only. The intrabuilding ports of this equipment must not be metallically connected to the
interfaces that connect to the OSP (outside plant) or its wiring. These interfaces are designed for use as
intrabuilding interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE) and require isolation
from the exposed OSP cabling. The addition of primary protectors is not sufficient protection to connect
these interfaces metallically to OSP wiring.
Note: All Ethernet cables must be shielded and grounded at both ends.
The ac-powered system does not require the use of an external surge protection device (SPD).
The dc-powered system employs an isolated DC return (DC-I) design. The DC battery return terminal
shall not be connected to the chassis or frame ground.
xPureFlex System: Installing and configuring IBM PureFlex System

Installing and configuring the system
Use the scenario and instructions to install and configure IBM PureFlex™System. Please note that the
latest version of this document is maintained online.
Before you begin
If you ordered a single IBM PureFlex System chassis (no rack), you must perform additional installation
steps. The following graphic shows the front and rear views of chassis-only Express configuration 4a:
Front Rear
P7EEL583-0
Note: If you ordered a single IBM PureFlex System chassis (no rack), ensure that you record the locations
of each of the chassis components before you remove them. Use the label template that was shipped with
the chassis to perform this task.
If you have Serial Attached SCSI (SAS) cables that where shipped with the system chassis, you must plug
them into the appropriate ports.
Small form-factor pluggable (SFP) transceivers should be taken from the ship group and placed in the
chassis as follows:
Table 1. Cable locations
Ship group content cable and SFPs Configuration 4.x ship group install actions
Description FRU Part
Number
1a
CN4093
2a
CN4093
3a
EN2092 FC5022
4a
EN4093 FC5022
eNet cable (ECB2) 40K8967 n/a 1x SW1:MGMT
SW2:MGMT
1x spare 1x SW1:MGMT
SW2:MGMT
1GB SFP (EB29) 81Y1620 2x SW1:p1-p2 2x SW1:p1-p2
2x SW2:p1-p2
0x n/a 2x SW1:p1-p2
2x SW2:p1-p2
10Gb SFP (EB28) 46C3449 1xSW1:p11 2x SW1:p11-p12
2x SW2:p11-p12
0x n/a 2x SW1:p3-p4
2x SW2:p3-p4
8Gb SFP (3286) 44E5687 1xSW1:p14 2x SW1:p14-p15
2x SW2:p14-p15
0x n/a 0x n/a
Figure 1. Front and rear views of chassis-only Express configuration 4a
© Copyright IBM Corp. 2012, 2013 1

Table 1. Cable locations (continued)
16Gb SFP (5371) 88Y6396 n/a n/a 2x SW3:p0,29
2x SW4:p0,29
2x SW3:p0,29
2x SW4:p0,29
Internal
Expansion Unit
Cable - HD SAS
to HD SAS
(ADA1)
90Y7687 Optional: Flex V7000 Controller to Flex V7000 Expansion Unit
Optional: Flex V7000 Expansion Unit to Flex V7000 Expansion Unit
eNet cable (1111) 40K8968 1x CMM1
1x CMM2
1x SW1:p1
1x spare 1xSW2:p1
QSFP+ cable
(EB2B)
49Y7934 0x n/a 1x SW1:p7
SW2:p7
0x n/a 1x SW1:p19
SW2:p19
Serial Chassis SW
(A2RR)
90Y9340
43X0510 2x user-installed when/if needed (debug)
Does not include FC EFPT Connect to Customer Management Network
For more information, see Setting up your IBM Flex System Enterprise Chassis.
If cables are taped to the top of the chassis, you must plug these cables into the appropriate ports
(identified with labels on each end of cable) after you have installed the chassis in the rack and
re-installed all the components in their specific bays. Once you have completed these tasks, you can
continue installing the rest of the system.
2PureFlex System: Installing and configuring IBM PureFlex System

Scenario: Installing the IBM PureFlex System
After you order an IBM PureFlex System, multiple groups ship, install, and configure your system.
The following figure shows the flow of events in a typical installation of the IBM PureFlex System.
P7EEL582-0
Configurationfor selection.
Anoption to consider
Configurationfor selection.
Anoption to consider.
Configurationfor selection.
Anoption to consider.
Determine which
configuration to
order.
User task
Order the system.
User task
IBM sends you
links to the
planning
information.
Manufacturing
builds the system.
Manufacturing ships
the system with
printed overview and
installation
documentation.
The shipping company
sends the system to
the actual installation
site while keeping in
contact with customer.
Accept the
physical order at
the loading dock.
User task
The shipping
company takes
over shipment.
Follow the
unpacking
instructions that
came with the
system.
User task
Contact IBM Lab Services
Team (if purchased) to tell
them to go ahead with the
next step.
User task
IBM Lab Services
Team (if purchased)
takes over.
Cable system to
the Chassis
Management
Module to ensure
that all hardware
components are
present and
functioning.
User task
Give IBM Lab
Services Team (if
purchased) the
network information
worksheet that you
completed after you
ordered.
User task
IBM Lab Services
Team (if purchased)
cables a laptop to
the management
network to access
the Management
Server Setup
wizard.
Work with
to complete
these steps:
IBM Lab Services
Team (if purchased)
User task
1. Accept any software
license agreements.
2. Set system-level user
IDs and passwords.
Wait until all LEDs on
the front of the rack
are green and are
blinking slowly.
User task
DO NOT POWER ON THE
SYSTEM AT THIS TIME.
Route and connect
power cables to a
power source, but do
not power on the
system.
User task
Installing and configuring the system 3

A typical installation scenario follows these steps:
1. You determine which configuration to order and then order the system.
2. IBM sends you links to the planning information.
3. IBM builds and ships your system.
4. A third party takes over shipment.
5. The shipping company sends the system to your installation site and maintains contact with you.
6. You accept the shipment.
7. You follow the unpacking instructions that came with the system.
8. You route and connect power cables to a power source, but do not power on the system.
9. You wait until all LEDs on the front of the rack are green and are blinking slowly.
10. You connect a device that has browser access and an Ethernet port to I/O module slot 1, port 6 on
the switch chassis to determine whether all hardware components are present and functioning.
11. You contact an IBM Services Team representative to request that they go ahead with the next step.
12. You meet with an IBM Services Team representative to complete the system configuration.
13. An IBM Services Team representative cables a laptop to the management network to access the
Management Server Setup wizard.
14. You work with an IBM Services Team representative to complete the following tasks:
vAccept software license agreements
vSet system-level user IDs and passwords
15. An IBM Services Team representative helps you learn more about configuring and using your
system.
Performing tasks associated with the 7953-94X rack
You must remove the 7953-94X rack outriggers, position the rack, install the system covers, and install the
rack stabilizer bracket before you install the system.
Procedure
1. Remove both outriggers (also known as rack side stabilizing brackets) from the sides of the rack by
removing the four bolts on each side with the 6 mm hex wrench that is provided. If you plan to move
the rack cabinet to another location, save the outriggers for use in the future.
Figure 2. Order and installation sequence
4PureFlex System: Installing and configuring IBM PureFlex System

P7EEL500-2
2. Position the rack where you want it to be installed.
3. Use the open-end wrench that comes with the hardware kit to lower each of the four leveling pads
just enough so that they touch the floor. The rack casters support the weight of the rack cabinet. The
pads prevent the rack from rolling.
4. Ensure that the power cords are securely attached to each power distribution unit (PDU).
5. Install the front, back, and side covers onto the system.
6. Install the recirculation prevention plate and the front stabilizer bracket on the front of the rack
cabinet. The recirculation prevention plate uses the same four screws and holes in the rack as the
front stabilizer bracket.
a. Align the four holes in the recirculation prevention plate with the four holes in the rack cabinet.
b. Position the front stabilizer bracket in front of the recirculation prevention plate and align the
screw holes.
c. Use the four screws and the hex wrench that come in the hardware kit to secure the front
stabilizer bracket and recirculation prevention plate (also referred to as the air baffle) to the rack
cabinet.
Figure 3. Removing the outriggers
Installing and configuring the system 5

d. Tighten the screws until the stabilizer bracket is flush against the recirculation prevention plate.
Removing the IBM Storwize V7000 shipping brackets
If present, remove the brackets that protect the IBM Storwize®V7000 controller during shipping.
Figure 4. Installing the recirculation plate and front stabilizer bracket
Figure 5. Installing the air baffle and front stabilizer bracket using the IBM PureFlex Rack Door Kit
6PureFlex System: Installing and configuring IBM PureFlex System

Procedure
1. Clip and remove the cable ties (A) that secure the power supplies and control canisters to the
shipping bracket.
Note: Ensure that you do not clip any cables.
2. Remove the two screws (B) that attach the bracket to the rack. See Figure 7 on page 8.
3. Loosen the three tension screws (C) on the shipping bracket.
Figure 6. Cable ties
Installing and configuring the system 7

4. Collapse the bracket.
Note: If the power supply is preventing the bracket from collapsing completely, slide the power
supply in enough to allow the bracket to collapse fully.
5. Grasp the shipping bracket and remove it from the rack.
6. Reseat the IBM Storwize V7000 control canisters.
a. Press the latches (A) on the unseated IBM Storwize V7000 control canister to access the control
canister handle.
Figure 7. Removing the screws that attach the bracket to the rack, and loosening the three tension screws
8PureFlex System: Installing and configuring IBM PureFlex System