IBP HDC75 User manual

HDC75 Display and Control Unit
Quick Start Guide and Safety Instructions
This document describes the major functions of the HDC75 instrument. The complete manual can be found
at http://www.ibpmt.com/btle.shtm. For reading the document dobe
®
PDF it's necessary to have dobe
®
PDF Reader installed.
ccount: Biotech-Lab
Password: btl ( B io t ech- L ab)
Support, manual and software updates are available at:
http://www.ibpmt.com/btle.shtm

SAFETY INSTRUCTIONS
Read this First
For your safety read and consider the safety instructions below carefully
• Read carefully the entire user manual of the Biotech-Lab system before using the
Biotech-Lab system.
• Read carefully the entire manual of the devices under test before connecting the
Biotech-Lab system to the devices under test.
• The battery included with the HDC7 does not arrive fully charged. The battery must be
charged for a minimum of 2 hours prior to use.
• Keep the devices away from unauthorized persons.
• Make sure that all Biotech-Lab Modules have valid calibration certificates.
• Only use the Biotech-Lab system in a dry environment and do not touch it with wet hands.
• Prevent every mechanical overstraining of electrical wires.
• If the acquired values seem to be not believable, make sure that the no device is defective.
• Prevent electrostatic discharge on the connectors. This can lead to substantial damage of
the Biotech-Lab devices and devices under test. Make sure to be completely discharged
before touching the connectors or cables connected to the instrument.
• Potentials above 42 V against earth ground are dangerous. This potentials can lead to
electrical shock and therefore to health hazards. Make sure that none of the connectors
has higher voltage than mentioned before.
• Never open a device of the Biotech-Lab system. There are no serviceable parts inside.

1 Getting to know the HDC75
The HDC75 is a robust smart device with Windows 10. It has five RS485-Interfaces for the direct connection
of the Biotech-Lab modules.
USB-Interface
Used also for charging the device. For charging use only the Quick-Charge 2.0
compatible charger delivered with the HDC75. If you charge the device with a
different charger the battery charge status of Windows 10 will not working properly
with the increased battery size of the HDC75.
Quick charge and fast charge modes are only entered when the charger is plugged in
while the HDC75 is completely turned off.
Turning on the HDC75 while in proper fast charge mode results in the sensor
ports being inaccessible as long as charging is in progress.
To activate the sensor ports again it is necessary to briefly unplug the USB charger
and then plug it in again. The charge circuit will revert to normal or slow charge
depending on the capabilities of the USB charger.
LED Green Charger connected
LED Red on: Charging with a standard charger at max. 5 V / 1500 m
LED Red blinking: Charging with Quick-Charge 2.0 mode at up to 12 V / 1500 m
Power Button
Turn on: Press and hold the power button about 5 seconds until the green LED gives
you a short blink feedback.
Turn off: Press and hold the power button until the device switches off.
Lock and unlock
Lock: Press the power button
Unlock: Press the power button to turn on the HDC75, than place your finger on the
lock icon and slide the icon to the unlock position.
RS485-Interface for the connection of the Biotech-Lab modules.
The connector next to the button is the number one and will be shown as the first
sensor in the Biotech-Lab Software.

2 S Windows 10
If you are not familiar with Windows 10 please navigate to:
http://windows.microsoft.com/en-us/windows-10/support
2.1 Changing the Display Language in Windows 10
To change the default language, sign in to Windows 10 and Go to “Start Menu” and select Settings.
Select “Time & Language”.
Select “Region & Language”
Select the region you are in.
Click “ dd a language”.

Click on the language you want,
and it will start downloading.
Go back to the “Time & Language”
screen and click on the language you
just installed.
You’ll see three options: “Set as
default”, “Options”, “Remove”.
Under “Options”, click “Download” to
download the language pack and
keyboard for that language.
If you open “Control Panel >
Languages”, you’ll see the traditional
settings which you are familiar with.

Changing the Display Language
To change the language of the user
account you are currently using,
select a language, then click “Set
as default.”

3 Biotech-Lab Biometer Software
The Biometer pp allows displaying measuring values from sensors, simulators and testers.
3.1 General Functionality
3.2 Head Area Functionality
Button Function
Scans all connected devices and shows the
devices suitable for this program.
Settings leads to the base settings of
Biotech-Lab.
Downloads the user manual.
Shows list of all values
Shows graph of all values
Shows statistic values of all Sensors
Head rea
Mode selection
Value Display rea.

3.3 Value Display Area Functionality
Depending on the connected devices different readouts are shown.
Element Function
This readout is a typical one value display
without any additional special functionality
in the display area.
This is a typical two value display.
L acc is the accumulated amount in L.
This is a typical two value display with an
additional functionality in the headline.
"Dialysis Machine Standard" indicates here
the selected conductivity temperature
compensation coefficient.
Shows settings for the particular device.
Shows additional features of the
particular device.
To return to the list view, press the
button again.
For sensors a single sensor graphic is
shown.
3.4 Single Sensor Graphic
fter pressing
leads to Graphic Settings
deletes the measured values
Additional Subfunction
The following functions are available with connected mouse only.
With a Right-Mouse-Click into the graphic you get the following menu
options.
More sub-functions below.

3.5 All Senor Graphics
fter pressing
3.6 Sub-functions accessible by mouse
To get the following sub-functions make a Left-Mouse-Click followed by a Right-Mouse-Click.
leads to Graphic Settings
deletes the measured values
Additional Subfunction
The following functions are available with connected mouse only.
With a Right-Mouse-Click into the graphic you get the following
menu options.
More sub-functions below.

Scale Range allows modifying the scales on both sides of
the graphic.
llows selecting the time interval.
llows selecting the colors of both the grid and the
backplane.
3.7 Statistic values
fter pressing
Element Function
Minimum Value
Maximum Value
rithmetic Mean Value
Standard Deviation
Current Value
Selection of Statistic Interval
This is the time range for the calculation of
the statistic values. The time range starts
from the last measuring value and goes
back with the selected value.
Head rea
Mode selection
Value Display rea

For your notes:

Revisions
Version Date Author Comments Software Version
1.00 15.05.16 Werner Pfingstmann Initial Version 1.00
1.01 05.09.16 Werner Pfingstmann Statistic Screen added
Details optimized
1.01
Contact
IBP Medical GmbH
Ikarusallee 15
D 30179 Hannover
Germany From US and Canada
Phone: [phone]
Fax: [phone]
Internet: http://www.ibpmedical.com http://www.ibpmedical.com
E-Mail: [email protected] [email protected]
Microsoft, Windows and Excel are either registered trademarks or trademarks of Microsoft Corporation.
Quick Charge 2.0 and QC2.0 are trademarks of Qualcomm, Inc.