Task Force Tips VORTEX 2 ER Programming manual

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
MANUAL: VORTEX®
MONITOR MOUNTED NOZZLES
INSTRUCTIONS FOR INSTALLATION, SAFE OPERATION AND MAINTENANCE
WARNING Understand manual before use. Operation of this device without understanding the manual and
receiving proper training is a misuse of this equipment. Obtain safety information at tft.com/
serialnumber.
This equipment is intended for use by trained and qualified emergency services personnel for
firefighting. All personnel using this equipment shall have completed a course of education
approved by the Authority Having Jurisdiction (AHJ).
This instruction manual is intended to familiarize firefighters and maintenance personnel with
the operation, servicing, and safety procedures associated with this product. This manual
should be kept available to all operating and maintenance personnel.
VORTEX 6 ERVORTEX 3 ER
VORTEX 2 ER
VORTEX 3VORTEX 2
ELECTRIC REMOTE OPERATED MODELS
MANUALLY OPERATED MODELS
TASK FORCE TIPS LLC
MADE IN USA • TFT.com
3701 Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 • 219-462-6161 • Fax [phone]

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
2
DANGER
PERSONAL RESPONSIBILITY CODE
The member companies of FEMSA that provide emergency response
equipment and services want responders to know and understand the
following:
1. Firefighting and Emergency Response are inherently dangerous activities
requiring proper training in their hazards and the use of extreme caution
at all times.
2. It is your responsibility to read and understand any user’s instructions,
including purpose and limitations, provided with any piece of equipment
you may be called upon to use.
3. It is your responsibility to know that you have been properly trained in
Firefighting and /or Emergency Response and in the use, precautions, and
care of any equipment you may be called upon to use.
4. It is your responsibility to be in proper physical condition and to maintain
the personal skill level required to operate any equipment you may be
called upon to use.
5. It is your responsibility to know that your equipment is in operable
condition and has been maintained in accordance with the manufacturer’s
instructions.
6. Failure to follow these guidelines may result in death, burns or other
severe injury.
FEMSA
Fire and Emergency Manufacturers and Service Association
P.O. Box 147, Lynnfield, MA 01940 • www.FEMSA.org

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
3
Table Of Contents
1.0 MEANING OF SAFETY SIGNAL WORDS
2.0 SAFETY
3.0 GENERAL INFORMATION
3.1 VARIOUS MODELS AND TERMS
3.2 SPECIFICATIONS
3.3 NOZZLE COUPLINGS
3.4 USE WITH SALT WATER
4.0 FLOW CHARACTERISTICS
4.1 VORTEX 2 AND 2 ER FLOW CHARACTERISTICS AND CHARTS
4.2 VORTEX 3 AND 3 ER FLOW CHARACTERISTICS AND CHARTS
4.3 VORTEX 6 ER FLOW CHARACTERISTICS AND CHARTS
5.0 INSTALLATION
5.1 VORTEX 2 AND 2 ER INSTALLATION
5.2 VORTEX 3 AND 3 ER INSTALLATION
5.2.1 VORTEX 3 AND 3 ER ORIENTATION
5.3 VORTEX 6 ER INSTALLATION
6.0 OPERATION
7.0 USE WITH FOAM
8.0 USE OF NOZZLES
9.0 WARRANTY
10.0 MAINTENANCE
10.1 FIELD LUBRICATION
10.2 SERVICE TESTING
10.3 REPAIR
11.0 DRAWINGS AND PART LISTS
12.0 OPERATION AND INSPECTION CHECKLIST

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
4
1.0 MEANING OF SAFETY SIGNAL WORDS
A safety related message is identified by a safety alert symbol and a signal word to indicate the level of risk involved with a particular
hazard. Per ANSI Z535.6, the definitions of the four signal words are as follows:
DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor
or moderate injury.
NOTICE NOTICE is used to address practices not related to physical injury.
2.0 SAFETY
DANGER An inadequate supply of pressure and/or flow will cause an ineffective stream and can result
in injury or death. Choose operating conditions to deliver adequate fire suppression. See flow
graphs
WARNING This equipment is intended for use by trained personnel for firefighting. Use of this equipment for
other purposes may involve hazards not addressed by this manual. Seek appropriate guidance
and training to reduce risk of injury
WARNING Equipment may be damaged if frozen while containing significant amounts of water. Such damage
may be difficult to detect visually. Subsequent pressurization can lead to injury or death. Any time
the equipment is subject to possible damage due to freezing, it must be tested and approved for
use by qualified personnel before being considered safe for use.
WARNING This device is not rated as ignition proof, explosion proof, or intrinsically safe. Use only in
locations with adequate ventilation and no hazard of flammable vapor buildup.
WARNING Application of water or foam solutions on energized electrical equipment could cause
electrocution. Serious injury or death could result. Assume circuits are energized until confirmed
to be de-energized. Do not apply water or foam to energized electrical equipment.
WARNING The stream exiting a nozzle is very powerful and capable of causing injury and property damage.
Make sure the nozzle is securely attached and pointing in a safe direction before water is turned
on. Do not direct water stream to cause injury or damage to persons or property.
WARNING Damage or injury could result from operating the monitor beyond the safe operating envelope. Do
not operate the monitor outside the envelope in the following graph(s).
NOTICE To prevent mechanical damage, do not drop or throw equipment.

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
5
3.0 GENERAL INFORMATION
The TFT VORTEX Nozzles enhance the use of smooth bore nozzles. They are intended for installation behind a smooth bore nozzle
for use with water or fire fighting foam solutions. Six short vanes in the bore of the VORTEX reduce turbulence in straight stream.
Actuating a VORTEX nozzle from “STREAM” to “VORTEX” causes the vanes to pivot proportionally. This induces a gentle spin in
the water to create a uniformly dispersed VORTEX stream pattern. The vanes are less obtrusive than a typical stream straightener,
resulting in virtually no friction loss regardless of which stream pattern is selected. The vanes also allow large debris to easily pass
through the VORTEX. Pattern selection is controlled with an electric drive on VORTEX ER nozzles. A manual actuation crank turned
by hand is used to change the pattern on manually operated versions.
3.1 VARIOUS MODELS AND TERMS
VORTEX 2 and 2 ER models are configured with a 2.5” female coupling and 2.5” male threads on the outlet for use with stacked tips.
VORTEX 3 and 3 ER models are configured with a 3.5” female coupling and 3.5” male threads on the outlet for use with stacked tips.
VORTEX 6 ER models are configured with a 6”NH female fixed coupling and 6”NH male threads on the outlet for use with connecting
to Tsunami Stacked Tips.
VORTEX
VORTEX ER
INLET COUPLING
OUTLET THREADS
MANUAL
ACTIVATION
CRANK
SERIAL NUMBER
ELECTRICAL QUICK
CONNECT FOR TFT
MONITORS
ELECTRIC ACTUATOR
MANUAL OVERRIDE
5/16" HEX
Figure 3.1
3.2 SPECIFICATIONS
VORTEX 2
VORTEX 2 ER
VORTEX 3
VORTEX 3 ER
VORTEX 6 ER
Maximum Flow Rate 1250 gpm (4500 l/min) 2500 gpm (9500 l/min) 8000 gpm (30,000 l/min)
Maximum Operating Pressure 300 psi (21 bar)
Hydrostatic Test Pressure 900 psi (62 bar)
Actuation Time for Full Travel* 4 seconds 8 seconds 14 seconds
Electrical Requirements* 12V / 24V
Waterway Diameter 2.5” (64 mm) 3.5” (89 mm) 6” (152 mm)
Standard Inlet/Outlet 2.5” NH, BSP, NPSH 2.5” NH, BSP, NPSH 6” NH
Overall Length 8.4” (213 mm) 9.0” (229 mm) 11” (279 mm)
Operating temperature of fluid 33° to 120°F (0° to 50°C)
Storage temperature range -40° to 150°F (-40° to 65°C)
Materials used Aluminum 6000 series hard anodized MIL8625 class 3 type 2,
stainless steel 300 series, nitrile rubber
* For ER Models Only
Figure 3.2

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
6
3.3 NOZZLE COUPLINGS
NH (National Hose Threads) threads are standard on all nozzles. Other threads such as NPSH (National Pipe Straight Hose) can
be specified at time of order.
CAUTION Mismatched or damaged waterway connections may cause equipment to leak or uncouple under
pressure. Failure could result in injury. Equipment must be mated to matched connections.
CAUTION Dissimilar metals coupled together can cause galvanic corrosion that can result in the inability
to uncouple the connection, or complete loss of engagement over time. Failure could cause
injury. Per NFPA 1962, if dissimilar metals are left coupled together, an anti-corrosive lubricant
should be applied to the connection and the coupling should be disconnected and inspected at
least quarterly.
3.4 USE WITH SALTWATER
Use with salt water is permissible provided the equipment is thoroughly cleaned with fresh water after each use. The service life of
the equipment may be shortened due to the effects of corrosion, and is not covered under warranty.

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
7
4.0 FLOW CHARACTERISTICS
4.1 VORTEX 2 & 2 ER FLOW CHARACTERISTICS AND CHARTS
The VORTEX 2 & 2 ER has 2.5” (65mm) waterway integrated into the outlet. If a smaller smooth bore is attached to the outlet, follow
the appropriate flow chart for the smaller orifice size instead.
1.375" Tip
0 500 1000 1500 2000 2500 3000 3500 4000 4500
Flow (lpm)
VORTEX® 2 & 2 ER with Smoothbores
0
20
40
60
80
100
120
140
160
180
200
Nozzle Pressure (psi)
0
2
4
6
8
10
12
Nozzle Pressure (bar)
0 125 250 375 500 625 750 875 1000 1125 1250
Flow (gpm)
1.0" Tip 1.25" Tip 1.5" Tip 1.75" Tip
(25 mm) (32 mm) (35 mm) (38 mm) (44 mm)
2.0" Tip
(51 mm)
Figure 4.1
2.5” (65 mm) Stacked Tip Flow Tables
Nozzle
Diameter
(inches)
Nozzle Pressure (PSI)
50 60 80 100
Flow
GPM
Reaction
lbf
Flow
GPM
Reaction
lbf
Flow
GPM
Reaction
lbf
Flow
GPM
Reaction
lbf
1210 79 230 94 266 126 297 157
1.25 328 123 360 147 415 196 464 245
1.375 397 148 435 178 502 237 562 297
1.5 473 177 518 212 598 283 668 353
1.75 643 240 705 288 814 385 910 481
2840 314 921 377 1063 502 1188 628
Nozzle
Diameter
(mm)
Nozzle Pressure (BAR)
3.5 4.1 5.5 7
Flow
LPM
Reaction
kgf
Flow
LPM
Reaction
kgf
Flow
LPM
Reaction
kgf
Flow
LPM
Reaction
kgf
25 795 36 871 43 1007 57 1124 71
32 1242 56 1363 67 1571 89 1756 111
35 1503 67 1647 81 1900 108 2127 135
38 1790 80 1961 96 2264 128 2529 160
44 2434 109 2669 131 3081 175 3445 218
51 3180 142 3486 171 4024 228 4497 285
Table 4.1

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
8
4.2 VORTEX 3 AND 3 ER FLOW CHARACTERISTICS AND CHARTS
The VORTEX 3 & 3 ER has a 3.5” (89mm) waterway integrated into the outlet. If a smaller smoothbore is attached to the outlet, follow
the appropriate flow chart for the smaller orifice size instead.
0.0 1000.0 2000.0 3 00 0. 0 4 00 0. 0 5 00 0.0 6000.0 7000.0 800 0.0 9 00 0. 0
0
2
4
6
8
10
12
0
20
40
60
80
100
120
140
160
180
200
0.0 500.0 1000.0 1500.0 2000.0 2500.0
Flow (lpm)
Nozzle Pressure (bar)
Nozzle Pressure (psi)
Flow (gpm)
VORTEX® 3 & 3 ER with Smoothbores
2" Tip
(51 mm)
2.25" Tip
(57 mm)
2.5" Tip
(64 mm)
2.75" Tip
(70 mm)
Figure 4.2
3.5” (89 mm) Stacked Tip Flow Tables
Nozzle
Diameter
(inches)
Nozzle Pressure (PSI)
50 60 80 100
Flow
GPM
Reaction
lbf
Flow
GPM
Reaction
lbf
Flow
GPM
Reaction
lbf
Flow
GPM
Reaction
lbf
2 840 314 921 377 1063 502 1188 628
2.25 1064 397 1165 477 1345 636 1504 795
2.5 1313 491 1438 589 1661 785 1857 981
2.75 1589 594 1740 712 2010 950 2247 1187
Nozzle
Diameter
(mm)
Nozzle Pressure (BAR)
3.5 4.1 5.5 7
Flow
LPM
Reaction
kgf
Flow
LPM
Reaction
kgf
Flow
LPM
Reaction
kgf
Flow
LPM
Reaction
kgf
51 1380 142 3486 171 4024 228 4479 285
57 4028 180 4410 216 5091 288 5693 361
64 4970 223 5443 276 6288 356 7030 445
70 6015 269 6587 323 7609 431 8506 539
Table 4.2

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
9
4.3 VORTEX 6 ER FLOW CHARACTERISTICS AND CHARTS
The VORTEX 6 ER has a 6” (157mm) waterway integrated into the outlet. If a smaller smoothbore is attached to the outlet, follow the
appropriate flow chart for the smaller orifice size instead.
Flow (lpm)
VORTEX® 6 ER with Smoothbores
0 5000 10000 15000 20000 25000 30000
Pressure (bar)
Pressure (psi)
0
4
8
12
0 1000 2000 3000 4000 5000 6000 7000 8000
Flow (gpm)
3.5" Tip
(90 mm) 4.0" Tip
(100 mm)
4.5" Tip
(115 mm)
5.125" Tip
(130 mm)
0
25
50
75
100
125
150
175
200
Figure 4.3
6” (157 mm) Stacked Tip Flow Tables
Nozzle
Diameter
(inches)
Nozzle Pressure (PSI)
50 60 80 100
Flow
GPM
Reaction
lbf
Flow
GPM
Reaction
lbf
Flow
GPM
Reaction
lbf
Flow
GPM
Reaction
lbf
3.5 2570 960 2820 1160 3260 1540 3640 1930
4 3360 1260 3680 1510 4250 2010 4750 2510
4.5 4250 1590 4660 1910 5380 2550 6020 3180
5.125 5520 2060 6040 2470 6980 3300 7800 4130
Nozzle
Diameter
(mm)
Nozzle Pressure (BAR)
3.5 4.1 5.5 7
Flow
LPM
Reaction
kgf
Flow
LPM
Reaction
kgf
Flow
LPM
Reaction
kgf
Flow
LPM
Reaction
kgf
90 9730 440 10670 530 12340 700 13780 880
100 12720 570 13930 690 16090 910 17980 1140
115 16090 720 17640 870 20360 1160 22790 1450
130 20890 940 22860 1120 26420 1500 29520 1880
Table 4.3

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
10
5.0 INSTALLATION
NOTICE Installing a stream straightener after the VORTEX will disrupt the dispersed pattern and produce
poor stream quality.
5.1 VORTEX 2 & 2 ER INSTALLATION
The VORTEX 2 & VORTEX 2 ER is intended to be installed on the outlet of a monitor and paired with stacked tips or smooth bores.
MST-3NJ 3 STACKED TIPS
VORTEX 2 ER
MST-4NJ 4 STACKED TIPS
VORTEX 2 ER
Figure 5.1
5.2 VORTEX 3 AND 3 ER INSTALLATION
The VORTEX 3 & VORTEX 3 ER is intended to be installed on the outlet of a monitor and paired with stacked tips or smooth bores.
YST-3NN STACKED TIPS
VORTEX 3
Figure 5.2

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
11
5.2.1 VORTEX 3 AND 3 ER ORIENTATION
The coupling on the VORTEX 3 or 3 ER is locked to the body. Once installed on the monitor, the orientation of the VORTEX can be
changed to position the motor housing appropriately for your installation. Instructions to orient the VORTEX are shown below.
1. Thread the VORTEX 3 on the monitor just until the gasket
starts to compress.
2. Back the set screw out (2) turns using a 5/32” hex key
3. Turn the VORTEX until it is oriented to the desired position.
4. Tighten the set screw to 45 in-lb.
5. Fully tighten the Vortex on the monitor.
SET SCREW
CAUTION Failure to tighten the set screw may allow the VORTEX to spin on it’s coupling while flowing water
in the dispersed VORTEX pattern.
Free spinning could result in injury or equipment damage. Set screw must be tightened to 45 in-lb.
5.3 VORTEX 6 ER INSTALLATION
The VORTEX 6 ER is intended to be installed in place of the straight section of the YST-8NX Tsunami Stacked Tips and paired with
stacked tips or smooth bores.
VORTEX 6 REPLACES STRAIGHT SECTION
Figure 5.3

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
12
6.0 OPERATION
The TFT VORTEX Nozzle allow the stream pattern to be infinitely varied from a straight stream to a uniformly dispersed VORTEX
pattern. Typical stream results are shown in Figure 6.0A.
Straight Stream Pattern Full VORTEX Pattern
Figure 6.0A
The VORTEX includes a label indicator for the user to confirm when the VORTEX is at the straight stream or in a VORTEX dispersed
position. As seen from the operating position behind the nozzle, actuating the VORTEX indicator counterclockwise moves into the
straight stream position. Actuating the VORTEX indicator clockwise will result in an increasingly wider pattern until reaching the full
VORTEX pattern.
VORTEX
STREAM
VORTEX
STREAM
Straight Stream Dispersed Pattern
Figure 6.0B
Pivoting the vanes has virtually no effect on the flow area or ability to pass large debris. As a result, discharge pressure and flow rate
remain constant regardless of stream pattern.
Manual override is possible on ER models by using the 5/16” hex head to drive the motor shaft. Manual versions include a crank
for actuating the VORTEX. Turning the shaft clockwise moves the nozzle towards a straight stream pattern. Turning the shaft
counterclockwise moves the nozzle to the dispersed VORTEX spray pattern. Do not force the shaft further after it stops firmly at each
end of stroke. Exceeding 60 in-lb (6.8 N·m) can damage the actuator.
CAUTION The electric drives are current limited but may still produce enough force to cause injury. To avoid
injury from a moving monitor:
• Be aware that the monitor may be remotely operated
• Keep hands and fingers away from pinch points on the monitor
• Never operate the manual override while electric controls are in operation

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
13
8.0 USE OF NOZZLES
IT IS THE RESPONSIBILITY OF THE INDIVIDUAL FIRE DEPARTMENT OR AGENCY TO DETERMINE PHYSICAL CAPABILITIES
AND SUITABILITY FOR AN INDIVIDUAL’S USE OF THIS EQUIPMENT.
Many factors contribute to the extinguishment of a fire. Among the most important is delivering water at a flow rate sufficient to absorb
heat faster than it is being generated. The flow rate depends largely on the pump discharge pressure and hose friction loss. It can be
calculated using a hydraulic equation such as:
PDP = NP + FL + DL + EL
PDP = Pump discharge pressure in PSI
NP = Nozzle pressure in PSI
FL = Hose friction loss in PSI
DL = Device loss in PSI
EL = Elevation loss in PSI
This Safety Manual is not intended as a substitute for proper
training in the use of rescue systems as taught from credible
sources such as the National Fire Protection Association (NFPA),
the International Fire Service Training Association (IFSTA), or
sources approved by the Authority Having Jurisdiction (AHJ).
7.0 USE WITH FOAM
The nozzle may be used with foam solutions. Refer to fire service training for the proper use of foam.
WARNING For Class B fires, lack of foam or interruption in the foam stream can cause a break in the foam
blanket and greatly increase the risk of injury or death. Follow procedures established by the AHJ
for the specific fuel and conditions.
WARNING Improper use of foam or using the wrong type of foam can result in illness, injury, or damage to
the environment. Follow foam manufacturer’s instructions and fire service training as directed by
the AHJ.

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
14
9.0 WARRANTY
Task Force Tips LLC, 3701 Innovation Way, Valparaiso, Indiana 46383-9327 USA (“TFT”) warrants to the original purchaser of
its products (“equipment”), and to anyone to whom it is transferred, that the equipment shall be free from defects in material and
workmanship during the five (5) year period from the date of purchase.
TFT’s obligation under this warranty is specifically limited to replacing or repairing the equipment (or its parts) which are shown by
TFT’s examination to be in a defective condition attributable to TFT. To qualify for this limited warranty, the claimant must return the
equipment to TFT, at 3701 Innovation Way, Valparaiso, Indiana 46383-9327 USA, within a reasonable time after discovery of the
defect. TFT will examine the equipment. If TFT determines that there is a defect attributable to it, TFT will correct the problem within
a reasonable time. If the equipment is covered by this limited warranty, TFT will assume the expenses of repair.
If any defect attributable to TFT under this limited warranty cannot be reasonably cured by repair or replacement, TFT may elect to
refund the purchase price of the equipment, less reasonable depreciation, in complete discharge of its obligations under this limited
warranty. If TFT makes this election, claimant shall return the equipment to TFT free and clear of any liens and encumbrances.
This is a limited warranty. The original purchaser of the equipment, any person to whom it is transferred, and any person who is
an intended or unintended beneficiary of the equipment, shall not be entitled to recover from TFT any consequential or incidental
damages for injury to person and/or property resulting from any defective equipment manufactured or assembled by TFT. It is agreed
and understood that the price stated for the equipment is in part consideration for limiting TFT’s liability. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
TFT shall have no obligation under this limited warranty if the equipment is, or has been, misused or neglected (including failure to
provide reasonable maintenance) or if there have been accidents to the equipment or if it has been repaired or altered by someone
else.
THIS IS A LIMITED EXPRESS WARRANTY ONLY. TFT EXPRESSLY DISCLAIMS WITH RESPECT TO THE EQUIPMENT ALL
IMPLIED WARRANTIES OF MERCHANTABILITY AND ALL IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE.
THERE IS NO WARRANTY OF ANY NATURE MADE BY TFT BEYOND THAT STATED IN THIS DOCUMENT.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
15
10.0 MAINTENANCE
TFT products are designed and manufactured to be damage resistant and require minimal maintenance. However, as the primary
firefighting tool upon which your life depends, it should be treated accordingly. To help prevent mechanical damage, do not drop or
throw equipment.
10.1 FIELD LUBRICATION
All Task Force Tips nozzles are factory lubricated with high quality silicone grease. This lubricant has excellent wash out resistance,
providing long term performance in firefighting nozzles. If your department has unusually hard or sandy water, the moving parts of the
nozzle may be affected. Foam agents and water additives contain soaps and chemicals that may break down the factory lubrication.
The moving parts of the nozzle should be checked on a regular basis for smooth and free operation, and for signs of damage. IF
THE NOZZLE IS OPERATING CORRECTLY, THEN NO ADDITIONAL LUBRICANT IS NEEDED. Any nozzle that is not operating
correctly should be immediately removed from service. The nozzle can be returned to the factory at any time for a complete checkup
and relubrication with silicone grease.
The field use of Break Free CLP (spray or liquid) lubricant will help to temporarily restore the smooth and free operation of the nozzle.
These lubricants do not have the washout resistance and long-term performance of the silicone grease. Once Break Free CLP is
applied, re-application will be needed on a regular basis until the nozzle can be returned to the factory for a complete checkup and
relubrication with silicone grease.
CAUTION Aerosol lubricants contain solvents that can swell O-Rings if applied in excess. The swelling can
inhibit smooth operation of the moving parts. When used in moderation, as directed, the solvents
quickly evaporate without adversely swelling the O-Rings.
10.2 SERVICE TESTING
In accordance with NFPA 1962, equipment must be tested a minimum of annually. Units failing any part of this test must be removed
from service, repaired and retested upon completion of the repair.
10.3 REPAIR
Factory service is available with repair time seldom exceeding one day in our facility. Factory serviced equipment is repaired by
experienced technicians, wet tested to original specifications, and promptly returned. Repair charges for non-warranty items are
minimal. Any returns should include a note as to the nature of the problem and whom to reach in case of questions.
Repair parts and service procedures are available for those wishing to perform their own repairs. Task Force Tips assumes no
liability for damage to equipment or injury to personnel that is a result of user service. Contact the factory or visit the web site at tft.
com for parts lists, exploded views, test procedures and troubleshooting guides. All replacement parts must be obtained from the
manufacturer to assure proper operation of the product, and to maintain approval of the device.
Performance tests shall be conducted on the equipment after a repair, or anytime a problem is reported to verify operation in
accordance with TFT test procedures. Consult factory for the procedure that corresponds to the model and serial number of the
equipment. Any equipment which fails the related test criteria should be removed from service immediately. Troubleshooting guides
are available with each test procedure or equipment can be returned to the factory for service and testing.
CAUTION Any alterations to the product or its markings could diminish safety and constitutes a misuse of
this product.
11.0 DRAWINGS AND PART LISTS
Exploded View Drawings and Part Lists for all VORTEX products are found at tft.com/serial-number.

©Copyright Task Force Tips LLC 2018 - 2020 LIS-045 May 5, 2019 Rev02
TASK FORCE TIPS LLC
MADE IN USA • tft.com
3701 Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 • 219-462-6161 • Fax [phone]
12.0 OPERATION AND INSPECTION CHECKLIST
BEFORE EACH USE, equipment must be inspected to this checklist:
1. There is no obvious damage such as missing, broken or loose parts, damaged labels, etc.
2. Internal vanes are free of debris
3. Coupling is tight and leak free
4. Nozzle flow is adequate as indicated by pump pressure and nozzle reaction
5. Nozzle turns freely and adjusts pattern through full range with electric and manual control
BEFORE BEING PLACED BACK IN SERVICE, equipment must be inspected to this list:
1. All controls and adjustments are operational.
2. There are no broken or missing parts.
3. There is no damage that could impair safe operation (e.g. detents, cracks, corrosion, or other defects).
4. The gasket is in good condition
5. The waterway is clear of obstructions
6. The equipment is clean and markings are legible
7. Coupling is retightened properly
8. Nozzle is set to the desired pattern
WARNING Equipment failing any part of the checklist is unsafe for use and must have the problem corrected
before use or being placed back into service. Operating equipment that has failed the checklist
is a misuse of this equipment.