Icom CT-M500 User manual
INSTRUCTIONS
EXTERNAL INTERFACE BOX
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Sep. 2021
A7626W-1EX-2 Printed in Japan
© 2021 Icom Inc. –1 –
–4 –
CT-M500
Thank you for choosing this Icom product.
READ ALL INSTRUCTIONS carefully and completely
before using this product.
■Important
SAVE THESE INSTRUCTIONS— These instructions
contain important operating instructions for the CT-M500.
This device connects to a transceiver through a Wireless
LAN (WLAN) and expands the transceiver’s functions.
For the WLAN setting, the functions that you can operate
when connecting to the transceiver, and so on, see the
transceiver’s manual for details.
The transceiver’s manual can be the
following internet address:
https://www.icomjapan.com/support/
LThese instructions are described based on the CT-M500 rmware
version 1.00.
Icom, Icom Inc. and the Icom logo are registered trademarks
of Icom Incorporated (Japan) in Japan, the United States,
the United Kingdom, Germany, France, Spain, Russia,
Australia, New Zealand, and/or other countries.
NMEA 2000 is a trademark of the National Maritime
Electronics Association, Inc.
All other products or brands are registered trademarks or
trademarks of their respective holders.
Icom is not responsible for the destruction, damage to, or
performance of any Icom or non-Icom equipment, if the
malfunction is because of:
• Force majeure, including, but not limited to, res,
earthquakes, storms, oods, lightning, other natural
disasters, disturbances, riots, war, or radioactive
contamination.
• The use of Icom devices with any equipment that is not
manufactured or approved by Icom.
■Explicit denitions
WORD DEFINITION
RWARNING! Personal injury, re hazard or electric shock
may occur.
CAUTION Equipment damage may occur.
NOTE If disregarded, inconvenience only. No risk
of personal injury, re or electric shock.
■Dénitions explicites
TERME DÉFINITION
RAVERTISSEMENT ! Risque de blessures corporelles,
d’incendie ou de choc électrique.
MISE EN GARDE Risque de dégât matériel.
REMARQUE
Inconvénient seulement, en cas de
nonrespect. Absence de risque de
blessures corporelles, d’incendie
ou de choc électrique.
■FCC information
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modications to this device, not expressly
approved by Icom Inc., could void your authority to operate this
device under FCC regulations.
■Information FCC
Cet appareil est conforme à la partie 15 de la réglementation
FCC. Son fonctionnement est soumis à la condition que cet
appareil ne provoque pas d’interférences nocives.
Cet équipement a été testé et reconnu conforme aux limites
xées pour un appareil numérique de classe B, conformément à
la partie 15 de la réglementation FCC. Ces limites ont été xées
an d'assurer une protection raisonnable contre les interférences
nocives dans une installation résidentielle. Cet équipement génère,
utilise et peut émettre un rayonnement de fréquence radio. S'il n'a
pas été installé conformément aux instructions, il peut par ailleurs
créer des interférences perturbant les communications radio.
Toutefois, il n'y a aucune garantie que les interférences ne se
produiront pas dans une installation particulière. Si cet équipement
crée des interférences perturbant la réception de la radio ou de
la télévision, comme cela peut être déterminé en éteignant et en
allumant l'équipement, l'utilisateur est invité à essayer de corriger
l'interférence en prenant une ou plusieurs des mesures ci-après :
• Réorienter ou changer de place l'antenne de réception.
• Éloigner l'équipement et le récepteur.
• Connecter l'équipement sur une prise sur un autre circuit que
celui sur lequel le récepteur est connecté.
• Faire appel au revendeur ou à un technicien radio/TV expérimenté.
MISE EN GARDE : Tout changement ou modication, non
expressément approuvé par Icom Inc., peut annuler l’autorisation de
l’utilisateur à utiliser cet appareil conformément à la réglementation FCC.
■Installing
You can mount the device on a dashboard using the
universal mounting bracket supplied with your device.
CAUTION:
• KEEP the device at least 1 meter (3.3 ft) away from the
vessel’s magnetic navigation compass.
• INSTALL the device within approximately 15 meters
from the transceiver, and in a place where there are no
obstacles between the device and the transceiver.
1. Mount the bracket securely to a surface which is more
than 10 mm thick and can support more than 5 kg using
the 4 supplied screws (5 × 20 mm).
NOTE: When mounting the device on a board, x the
bracket to the board using the user supplied bolts and
nuts, as shown below.
2. Attach the device to the bracket.
Mounting Example
Spring washer
Flat washer
■Specications and options
DSpecications
General
Operating
temperature range –20°C ~ +60°C, –4ºF ~ +140ºF
Power supply
requirement
Negative ground:
13.8 V DC nominal (10.8 ~ 15.9 V)
Current drain
(at 13.8 V) 3.5 A maximum
Dimensions
(approximate)
(projections not
included)
156.5 (W) × 67.6 (H) × 82.1 (D) mm,
6.2 (W) × 2.7 (H) × 3.2 (D) in
Weight
(approximate) 430 g, 15.2 oz
Wireless LAN
Wireless LAN standard
IEEE802.11 b/g/n
Authentication and
Encryption
WEP (64/128 bit),
WPA-PSK (TKIP),
WPA2-PSK (AES)
Channels 1 to 13 (2.4 GHz band)
LMay dier depending on the country of use.
Output power Less than 10 mW/MHz
Hailer
Audio output power More than 25 W into a 4 Ω load
RX Hailer
Audio output power More than 20 W into a 4 Ω load
DOptions
• SP-37 HORN SPEAKER
DDimensions
51 (2)
66.5 (2.6)
192.2 (7.6)
137 (5.4)
156.5 (6.2)
26 (1) 67.6 (2.7)
60.8 (2.4)
84.4 (3.3)21.3 (0.8)
172.2 (6.8)
82.1 (3.2)
Unit: mm (inch)
■Fuse replacement
One fuse is installed in the supplied DC power cable. If the
fuse blows or the device stops functioning, track down the
source of the problem, repair it, and replace the damaged
fuse with a new one of the proper rating.
Fuse rating: 250 V 5 A
Fuse Coding explanation
Fuse Coding: F 250 V 5 A
Fuse Voltage Rating: 250 Volts
Fuse Current Rating: 5 Amperes
■Recommendation
CLEAN THE DEVICE THOROUGHLY WITH FRESH WATER
after exposure to saltwater, and dry it before using. Otherwise, the
device’s keys may become unusable, due to salt crystallization.
NOTE: If the device’s waterproof protection appears defective,
carefully clean it with a soft, damp (fresh water) cloth, then dry it
before operating.
The device may lose its waterproof protection if the case is
cracked or broken, or the device has been dropped.
Contact your Icom distributor or your dealer for advice.
INSTRUCTIONS
EXTERNAL INTERFACE BOX
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Sep. 2021
A7626W-1EX-2 Printed in Japan
© 2021 Icom Inc. –1 –
–4 –
CT-M500
Thank you for choosing this Icom product.
READ ALL INSTRUCTIONS carefully and completely
before using this product.
■Important
SAVE THESE INSTRUCTIONS— These instructions
contain important operating instructions for the CT-M500.
This device connects to a transceiver through a Wireless
LAN (WLAN) and expands the transceiver’s functions.
For the WLAN setting, the functions that you can operate
when connecting to the transceiver, and so on, see the
transceiver’s manual for details.
The transceiver’s manual can be downloaded from the
following internet address:
https://www.icomjapan.com/support/
LThese instructions are described based on the CT-M500 rmware
version 1.00.
Icom, Icom Inc. and the Icom logo are registered trademarks
of Icom Incorporated (Japan) in Japan, the United States,
the United Kingdom, Germany, France, Spain, Russia,
Australia, New Zealand, and/or other countries.
NMEA 2000 is a trademark of the National Maritime
Electronics Association, Inc.
All other products or brands are registered trademarks or
trademarks of their respective holders.
Icom is not responsible for the destruction, damage to, or
performance of any Icom or non-Icom equipment, if the
malfunction is because of:
• Force majeure, including, but not limited to, res,
earthquakes, storms, oods, lightning, other natural
disasters, disturbances, riots, war, or radioactive
contamination.
• The use of Icom devices with any equipment that is not
manufactured or approved by Icom.
■Explicit denitions
WORD DEFINITION
RWARNING! Personal injury, re hazard or electric shock
may occur.
CAUTION Equipment damage may occur.
NOTE If disregarded, inconvenience only. No risk
of personal injur hock.
■Dénitions explicites
TERME DÉFINITION
RAVERTISSEMENT ! Risque de blessures corporelles,
d’incendie ou de choc électrique.
MISE EN GARDE Risque de dégât matériel.
REMARQUE
Inconvénient seulement, en cas de
nonrespect. Absence de risque de
blessures corporelles, d’incendie
ou de choc électrique.
■FCC information
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modications to this device, not expressly
approved by Icom Inc., could void your authority to operate this
device under FCC regulations.
■Information FCC
Cet appareil est conforme à la partie 15 de la réglementation
FCC. Son fonctionnement est soumis à la condition que cet
appareil ne provoque pas d’interférences nocives.
Cet équipement a été testé et reconnu conforme aux limites
xées pour un appareil numérique de classe B, conformément à
la partie 15 de la réglementation FCC. Ces limites ont été xées
an d'assurer une protection raisonnable contre les interférences
nocives dans une installation résidentielle. Cet équipement génère,
utilise et peut émettre un rayonnement de fréquence radio. S'il n'a
pas été installé conformément aux instructions, il peut par ailleurs
créer des interférences perturbant les communications radio.
Toutefois, il n'y a aucune garantie que les interférences ne se
produiront pas dans une installation particulière. Si cet équipement
crée des interférences perturbant la réception de la radio ou de
la télévision, comme cela peut être déterminé en éteignant et en
allumant l'équipement, l'utilisateur est invité à essayer de corriger
l'interférence en prenant une ou plusieurs des mesures ci-après :
• Réorienter ou changer de place l'antenne de réception.
• Éloigner l'équipement et le récepteur.
• Connecter l'équipement sur une prise sur un autre circuit que
celui sur lequel le récepteur est connecté.
• Faire appel au revendeur ou à un technicien radio/TV expérimenté.
MISE EN GARDE : Tout changement ou modication, non
expressément approuvé par Icom Inc., peut annuler l’autorisation de
l’utilisateur à utiliser cet appareil conformément à la réglementation FCC.
■Installing
You can mount the device on a dashboard using the
universal mounting bracket supplied with your device.
CAUTION:
• KEEP the device at least 1 meter (3.3 ft) away from the
vessel’s magnetic navigation compass.
• INSTALL the device within approximately 15 meters
from the transceiver, and in a place where there are no
obstacles between the device and the transceiver.
1. Mount the bracket securely to a surface which is more
than 10 mm thick and can support more than 5 kg using
the 4 supplied screws (5 × 20 mm).
NOTE: When mounting the device on a board, x the
bracket to the board using the user supplied bolts and
nuts, as shown below.
2. Attach the device to the bracket.
Mounting Example
Spring washer
Flat washer
■Specications and options
DSpecications
General
Operating
temperature range –20°C ~ +60°C, –4ºF ~ +140ºF
Power supply
requirement
Negative ground:
13.8 V DC nominal (10.8 ~ 15.9 V)
Current drain
(at 13.8 V) 3.5 A maximum
Dimensions
(approximate)
(projections not
included)
156.5 (W) × 67.6 (H) × 82.1 (D) mm,
6.2 (W) × 2.7 (H) × 3.2 (D) in
Weight
(approximate) 430 g, 15.2 oz
Wireless LAN
Wireless LAN standard
IEEE802.11 b/g/n
Authentication and
Encryption
WEP (64/128 bit),
WPA-PSK (TKIP),
WPA2-PSK (AES)
Channels 1 to 13 (2.4 GHz band)
LMay dier depending on the country of use.
Output power Less than 10 mW/MHz
Hailer
Audio output power More than 25 W into a 4 Ω load
RX Hailer
Audio output power More than 20 W into a 4 Ω load
DOptions
• SP-37 HORN SPEAKER
DDimensions
51 (2)
66.5 (2.6)
192.2 (7.6)
137 (5.4)
156.5 (6.2)
26 (1) 67.6 (2.7)
60.8 (2.4)
84.4 (3.3)21.3 (0.8)
172.2 (6.8)
82.1 (3.2)
Unit: mm (inch)
■Fuse replacement
One fuse is installed in the supplied DC power cable. If the
fuse blows or the device stops functioning, track down the
source of the problem, repair it, and replace the damaged
fuse with a new one of the proper rating.
Fuse rating: 250 V 5 A
Fuse Coding explanation
Fuse Coding: F 250 V 5 A
Fuse Voltage Rating: 250 Volts
Fuse Current Rating: 5 Amperes
■Recommendation
CLEAN THE DEVICE THOROUGHLY WITH FRESH WATER
after exposure to saltwater, and dry it before using. Otherwise, the
device’s keys may become unusable, due to salt crystallization.
NOTE: If the device’s waterproof protection appears defective,
carefully clean it with a soft, damp (fresh water) cloth, then dry it
before operating.
The device may lose its waterproof protection if the case is
cracked or broken, or the device has been dropped.
Contact your Icom distributor or your dealer for advice.
INSTRUCTIONS
EXTERNAL INTERFACE BOX
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Sep. 2021
A7626W-1EX-2 Printed in Japan
© 2021 Icom Inc. –1 –
–4 –
CT-M500
Thank you for choosing this Icom product.
READ ALL INSTRUCTIONS carefully and completely
before using this product.
■Important
SAVE THESE INSTRUCTIONS— These instructions
contain important operating instructions for the CT-M500.
This device connects to a transceiver through a Wireless
LAN (WLAN) and expands the transceiver’s functions.
For the WLAN setting, the functions that you can operate
when connecting to the transceiver, and so on, see the
transceiver’s manual for details.
The transceiver’s manual can be downloaded from the
following internet address:
https://www.icomjapan.com/support/
LThese instructions are described based on the CT-M500 rmware
version 1.00.
Icom, Icom Inc. and the Icom logo are registered trademarks
of Icom Incorporated (Japan) in Japan, the United States,
the United Kingdom, Germany, France, Spain, Russia,
Australia, New Zealand, and/or other countries.
NMEA 2000 is a trademark of the National Maritime
Electronics Association, Inc.
All other products or brands are registered trademarks or
trademarks of their respective holders.
Icom is not responsible for the destruction, damage to, or
performance of any Icom or non-Icom equipment, if the
malfunction is because of:
• Force majeure, including, but not limited to, res,
earthquakes, storms, oods, lightning, other natural
disasters, disturbances, riots, war, or radioactive
contamination.
• The use of Icom devices with any equipment that is not
manufactured or approved by Icom.
■Explicit denitions
WORD DEFINITION
RWARNING! Personal injury, re hazard or electric shock
may occur.
CAUTION Equipment dama
NOTE If disregarded, in No risk
of personal injury, re or electric shock.
■Dénitions explicites
TERME DÉFINITION
RAVERTISSEMENT ! Risque de blessures corporelles,
d’incendie ou de choc électrique.
MISE EN GARDE Risque de dégât matériel.
REMARQUE
Inconvénient seulement, en cas de
nonrespect. Absence de risque de
blessures corporelles, d’incendie
ou de choc électrique.
■FCC information
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modications to this device, not expressly
approved by Icom Inc., could void your authority to operate this
device under FCC regulations.
■Information FCC
Cet appareil est conforme à la partie 15 de la réglementation
FCC. Son fonctionnement est soumis à la condition que cet
appareil ne provoque pas d’interférences nocives.
Cet équipement a été testé et reconnu conforme aux limites
xées pour un appareil numérique de classe B, conformément à
la partie 15 de la réglementation FCC. Ces limites ont été xées
an d'assurer une protection raisonnable contre les interférences
nocives dans une installation résidentielle. Cet équipement génère,
utilise et peut émettre un rayonnement de fréquence radio. S'il n'a
pas été installé conformément aux instructions, il peut par ailleurs
créer des interférences perturbant les communications radio.
Toutefois, il n'y a aucune garantie que les interférences ne se
produiront pas dans une installation particulière. Si cet équipement
crée des interférences perturbant la réception de la radio ou de
la télévision, comme cela peut être déterminé en éteignant et en
allumant l'équipement, l'utilisateur est invité à essayer de corriger
l'interférence en prenant une ou plusieurs des mesures ci-après :
• Réorienter ou changer de place l'antenne de réception.
• Éloigner l'équipement et le récepteur.
• Connecter l'équipement sur une prise sur un autre circuit que
celui sur lequel le récepteur est connecté.
• Faire appel au revendeur ou à un technicien radio/TV expérimenté.
MISE EN GARDE : Tout changement ou modication, non
expressément approuvé par Icom Inc., peut annuler l’autorisation de
l’utilisateur à utiliser cet appareil conformément à la réglementation FCC.
■Installing
You can mount the device on a dashboard using the
universal mounting bracket supplied with your device.
CAUTION:
• KEEP the device at least 1 meter (3.3 ft) away from the
vessel’s magnetic navigation compass.
• INSTALL the device within approximately 15 meters
from the transceiver, and in a place where there are no
obstacles between the device and the transceiver.
1. Mount the bracket securely to a surface which is more
than 10 mm thick and can support more than 5 kg using
the 4 supplied screws (5 × 20 mm).
NOTE: When mounting the device on a board, x the
bracket to the board using the user supplied bolts and
nuts, as shown below.
2. Attach the device to the bracket.
Mounting Example
Spring washer
Flat washer
■Specications and options
DSpecications
General
Operating
temperature range –20°C ~ +60°C, –4ºF ~ +140ºF
Power supply
requirement
Negative ground:
13.8 V DC nominal (10.8 ~ 15.9 V)
Current drain
(at 13.8 V) 3.5 A maximum
Dimensions
(approximate)
(projections not
included)
156.5 (W) × 67.6 (H) × 82.1 (D) mm,
6.2 (W) × 2.7 (H) × 3.2 (D) in
Weight
(approximate) 430 g, 15.2 oz
Wireless LAN
Wireless LAN standard
IEEE802.11 b/g/n
Authentication and
Encryption
WEP (64/128 bit),
WPA-PSK (TKIP),
WPA2-PSK (AES)
Channels 1 to 13 (2.4 GHz band)
LMay dier depending on the country of use.
Output power Less than 10 mW/MHz
Hailer
Audio output power More than 25 W into a 4 Ω load
RX Hailer
Audio output power More than 20 W into a 4 Ω load
DOptions
• SP-37 HORN SPEAKER
DDimensions
51 (2)
66.5 (2.6)
192.2 (7.6)
137 (5.4)
156.5 (6.2)
26 (1) 67.6 (2.7)
60.8 (2.4)
84.4 (3.3)21.3 (0.8)
172.2 (6.8)
82.1 (3.2)
Unit: mm (inch)
■Fuse replacement
One fuse is installed in the supplied DC power cable. If the
fuse blows or the device stops functioning, track down the
source of the problem, repair it, and replace the damaged
fuse with a new one of the proper rating.
Fuse rating: 250 V 5 A
Fuse Coding explanation
Fuse Coding: F 250 V 5 A
Fuse Voltage Rating: 250 Volts
Fuse Current Rating: 5 Amperes
■Recommendation
CLEAN THE DEVICE THOROUGHLY WITH FRESH WATER
after exposure to saltwater, and dry it before using. Otherwise, the
device’s keys may become unusable, due to salt crystallization.
NOTE: If the device’s waterproof protection appears defective,
carefully clean it with a soft, damp (fresh water) cloth, then dry it
before operating.
The device may lose its waterproof protection if the case is
cracked or broken, or the device has been dropped.
Contact your Icom distributor or your dealer for advice.
INSTRUCTIONS
EXTERNAL INTERFACE BOX
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Sep. 2021
A7626W-1EX-2 Printed in Japan
© 2021 Icom Inc. –1 –
–4 –
CT-M500
Thank you for choosing this Icom product.
READ ALL INSTRUCTIONS carefully and completely
before using this product.
■Important
SAVE THESE INSTRUCTIONS— These instructions
contain important operating instructions for the CT-M500.
This device connects to a transceiver through a Wireless
LAN (WLAN) and expands the transceiver’s functions.
For the WLAN setting, the functions that you can operate
when connecting to the transceiver, and so on, see the
transceiver’s manual for details.
The transceiver’s manual can be the
following internet address:
https://www.icomjapan.com/support/
LThese instructions are described based on the CT-M500 rmware
version 1.00.
Icom, Icom Inc. and the Icom logo are registered trademarks
of Icom Incorporated (Japan) in Japan, the United States,
the United Kingdom, Germany, France, Spain, Russia,
Australia, New Zealand, and/or other countries.
NMEA 2000 is a trademark of the National Maritime
Electronics Association, Inc.
All other products or brands are registered trademarks or
trademarks of their respective holders.
Icom is not responsible for the destruction, damage to, or
performance of any Icom or non-Icom equipment, if the
malfunction is because of:
• Force majeure, including, but not limited to, res,
earthquakes, storms, oods, lightning, other natural
disasters, disturbances, riots, war, or radioactive
contamination.
• The use of Icom devices with any equipment that is not
manufactured or approved by Icom.
■Explicit denitions
WORD DEFINITION
RWARNING! Personal injury, re hazard or electric shock
may occur.
CAUTION Equipment damage may occur.
NOTE If disregarded, inconvenience only. No risk
of personal injury, re or electric shock.
■Dénitions explicites
TERME DÉFINITION
RAVERTISSEMENT ! Risque de blessures corporelles,
d’incendie ou de choc électrique.
MISE EN GARDE Risque de dégât matériel.
REMARQUE
Inconvénient seulement, en cas de
nonrespect. Absence de risque de
blessures corporelles, d’incendie
ou de choc électrique.
■FCC information
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modications to this device, not expressly
approved by Icom Inc., could void your authority to operate this
device under FCC regulations.
■Information FCC
Cet appareil est conforme à la partie 15 de la réglementation
FCC. Son fonctionnement est soumis à la condition que cet
appareil ne provoque pas d’interférences nocives.
Cet équipement a été testé et reconnu conforme aux limites
xées pour un appareil numérique de classe B, conformément à
la partie 15 de la réglementation FCC. Ces limites ont été xées
an d'assurer une protection raisonnable contre les interférences
nocives dans une installation résidentielle. Cet équipement génère,
utilise et peut émettre un rayonnement de fréquence radio. S'il n'a
pas été installé conformément aux instructions, il peut par ailleurs
créer des interférences perturbant les communications radio.
Toutefois, il n'y a aucune garantie que les interférences ne se
produiront pas dans une installation particulière. Si cet équipement
crée des interférences perturbant la réception de la radio ou de
la télévision, comme cela peut être déterminé en éteignant et en
allumant l'équipement, l'utilisateur est invité à essayer de corriger
l'interférence en prenant une ou plusieurs des mesures ci-après :
• Réorienter ou changer de place l'antenne de réception.
• Éloigner l'équipement et le récepteur.
• Connecter l'équipement sur une prise sur un autre circuit que
celui sur lequel le récepteur est connecté.
• Faire appel au revendeur ou à un technicien radio/TV expérimenté.
MISE EN GARDE : Tout changement ou modication, non
expressément approuvé par Icom Inc., peut annuler l’autorisation de
l’utilisateur à utiliser cet appareil conformément à la réglementation FCC.
■Installing
You can mount the device on a dashboard using the
universal mounting bracket supplied with your device.
CAUTION:
• KEEP the device at least 1 meter (3.3 ft) away from the
vessel’s magnetic navigation compass.
• INSTALL the device within approximately 15 meters
from the transceiver, and in a place where there are no
obstacles between the device and the transceiver.
1. Mount the bracket securely to a surface which is more
than 10 mm thick and can support more than 5 kg using
the 4 supplied screws (5 × 20 mm).
NOTE: When mounting the device on a board, x the
bracket to the board using the user supplied bolts and
nuts, as shown below.
2. Attach the device to the bracket.
Mounting Example
Spring washer
Flat washer
■Specications and options
DSpecications
General
Operating
temperature range –20°C ~ +60°C, –4ºF ~ +140ºF
Power supply
requirement
Negative ground:
13.8 V DC nominal (10.8 ~ 15.9 V)
Current drain
(at 13.8 V) 3.5 A maximum
Dimensions
(approximate)
(projections not
included)
156.5 (W) × 67.6 (H) × 82.1 (D) mm,
6.2 (W) × 2.7 (H) × 3.2 (D) in
Weight
(approximate) 430 g, 15.2 oz
Wireless LAN
Wireless LAN standard
IEEE802.11 b/g/n
Authentication and
Encryption
WEP (64/128 bit),
WPA-PSK (TKIP),
WPA2-PSK (AES)
Channels 1 to 13 (2.4 GHz band)
LMay dier depending on the country of use.
Output power Less than 10 mW/MHz
Hailer
Audio output power More than 25 W into a 4 Ω load
RX Hailer
Audio output power More than 20 W into a 4 Ω load
DOptions
• SP-37 HORN SPEAKER
DDimensions
51 (2)
66.5 (2.6)
192.2 (7.6)
137 (5.4)
156.5 (6.2)
26 (1) 67.6 (2.7)
60.8 (2.4)
84.4 (3.3)21.3 (0.8)
172.2 (6.8)
82.1 (3.2)
Unit: mm (inch)
■Fuse replacement
One fuse is installed in the supplied DC power cable. If the
fuse blows or the device stops functioning, track down the
source of the problem, repair it, and replace the damaged
fuse with a new one of the proper rating.
Fuse rating: 250 V 5 A
Fuse Coding explanation
Fuse Coding: F 250 V 5 A
Fuse Voltage Rating: 250 Volts
Fuse Current Rating: 5 Amperes
■Recommendation
CLEAN THE DEVICE THOROUGHLY WITH FRESH WATER
after exposure to saltwater, and dry it before using. Otherwise, the
device’s keys may become unusable, due to salt crystallization.
NOTE: If the device’s waterproof protection appears defective,
carefully clean it with a soft, damp (fresh water) cloth, then dry it
before operating.
The device may lose its waterproof protection if the case is
cracked or broken, or the device has been dropped.
Contact your Icom distributor or your dealer for advice.
INSTRUCTIONS
EXTERNAL INTERFACE BOX
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Sep. 2021
A7626W-1EX-2 Printed in Japan
© 2021 Icom Inc. –1 –
–4 –
CT-M500
Thank you for choosing this Icom product.
READ ALL INSTRUCTIONS carefully and completely
before using this product.
■Important
SAVE THESE INSTRUCTIONS— These instructions
contain important operating instructions for the CT-M500.
This device connects to a transceiver through a Wireless
LAN (WLAN) and expands the transceiver’s functions.
For the WLAN setting, the functions that you can operate
when connecting to the transceiver, and so on, see the
transceiver’s manual for details.
The transceiver’s manual can be downloaded from the
following internet address:
https://www.icomjapan.com/support/
LThese instructions are described based on the CT-M500 rmware
version 1.00.
Icom, Icom Inc. and the Icom logo are registered trademarks
of Icom Incorporated (Japan) in Japan, the United States,
the United Kingdom, Germany, France, Spain, Russia,
Australia, New Zealand, and/or other countries.
NMEA 2000 is a trademark of the National Maritime
Electronics Association, Inc.
All other products or brands are registered trademarks or
trademarks of their respective holders.
Icom is not responsible for the destruction, damage to, or
performance of any Icom or non-Icom equipment, if the
malfunction is because of:
• Force majeure, including, but not limited to, res,
earthquakes, storms, oods, lightning, other natural
disasters, disturbances, riots, war, or radioactive
contamination.
• The use of Icom devices with any equipment that is not
manufactured or approved by Icom.
■Explicit denitions
WORD DEFINITION
RWARNING! Personal injury, re hazard or electric shock
may occur.
CAUTION Equipment damage may occur.
NOTE If disregarded, inconvenience only. No risk
of personal injury, re or electric shock.
■Dénitions explicites
TERME DÉFINITION
RAVERTISSEMENT ! Risque de blessures corporelles,
d’incendie ou de choc électrique.
MISE EN GARDE Risque de dégât matériel.
REMARQUE
Inconvénient seulement, en cas de
nonrespect. Absence de risque de
blessures corporelles, d’incendie
ou de choc électrique.
■FCC information
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modications to this device, not expressly
approved by Icom Inc., could void your authority to operate this
device under FCC regulations.
■Information FCC
Cet appareil est conforme à la partie 15 de la réglementation
FCC. Son fonctionnement est soumis à la condition que cet
appareil ne provoque pas d’interférences nocives.
Cet équipement a été testé et reconnu conforme aux limites
xées pour un appareil numérique de classe B, conformément à
la partie 15 de la réglementation FCC. Ces limites ont été xées
an d'assurer une protection raisonnable contre les interférences
nocives dans une installation résidentielle. Cet équipement génère,
utilise et peut émettre un rayonnement de fréquence radio. S'il n'a
pas été installé conformément aux instructions, il peut par ailleurs
créer des interférences perturbant les communications radio.
Toutefois, il n'y a aucune garantie que les interférences ne se
produiront pas dans une installation particulière. Si cet équipement
crée des interférences perturbant la réception de la radio ou de
la télévision, comme cela peut être déterminé en éteignant et en
allumant l'équipement, l'utilisateur est invité à essayer de corriger
l'interférence en prenant une ou plusieurs des mesures ci-après :
• Réorienter ou changer de place l'antenne de réception.
• Éloigner l'équipement et le récepteur.
• Connecter l'équipement sur une prise sur un autre circuit que
celui sur lequel le récepteur est connecté.
• Faire appel au revendeur ou à un technicien radio/TV expérimenté.
MISE EN GARDE : Tout changement ou modication, non
expressément approuvé par Icom Inc., peut annuler l’autorisation de
l’utilisateur à utiliser cet appareil conformément à la réglementation FCC.
■Installing
You can mount the device on a dashboard using the
universal mounting bracket supplied with your device.
CAUTION:
• KEEP the device at least 1 meter (3.3 ft) away from the
vessel’s magnetic navigation compass.
• INSTALL the device within approximately 15 meters
from the transceiver, and in a place where there are no
obstacles between the device and the transceiver.
1. Mount the bracket securely to a surface which is more
than 10 mm thick and can support more than 5 kg using
the 4 supplied screws (5 × 20 mm).
NOTE: When mounting the device on a board, x the
bracket to the board using the user supplied bolts and
nuts, as shown below.
2. Attach the device to the bracket.
Mounting Example
Spring washer
Flat washer
■Specications and options
DSpecications
General
Operating
temperature range –20°C ~ +60°C, –4ºF ~ +140ºF
Power supply
requirement
Negative ground:
13.8 V DC nominal (10.8 ~ 15.9 V)
Current drain
(at 13.8 V) 3.5 A maximum
Dimensions
(approximate)
(projections not
included)
156.5 (W) × 67.6 (H) × 82.1 (D) mm,
6.2 (W) × 2.7 (H) × 3.2 (D) in
Weight
(approximate) 430 g, 15.2 oz
Wireless LAN
Wireless LAN standard
IEEE802.11 b/g/n
Authentication and
Encryption
WEP (64/128 bit),
WPA-PSK (TKIP),
WPA2-PSK (AES)
Channels 1 to 13 (2.4 GHz band)
LMay dier depending on the country of use.
Output power Less than 10 mW/MHz
Hailer
Audio output power More than 25 W into a 4 Ω load
RX Hailer
Audio output power More than 20 W into a 4 Ω load
DOptions
• SP-37 HORN SPEAKER
DDimensions
51 (2)
66.5 (2.6)
192.2 (7.6)
137 (5.4)
156.5 (6.2)
26 (1) 67.6 (2.7)
60.8 (2.4)
84.4 (3.3)21.3 (0.8)
172.2 (6.8)
82.1 (3.2)
Unit: mm (inch)
■Fuse replacement
One fuse is installed in the supplied DC power cable. If the
fuse blows or the device stops functioning, track down the
source of the problem, repair it, and replace the damaged
fuse with a new one of the proper rating.
Fuse rating: 250 V 5 A
Fuse Coding explanation
Fuse Coding: F 250 V 5 A
Fuse Voltage Rating: 250 Volts
Fuse Current Rating: 5 Amperes
■Recommendation
CLEAN THE DEVICE THOROUGHLY WITH FRESH WATER
after exposure to saltwater, and dry it before using. Otherwise, the
device’s keys may become unusable, due to salt crystallization.
NOTE: If the device’s waterproof protection appears defective,
carefully clean it with a soft, damp (fresh water) cloth, then dry it
before operating.
The device may lose its waterproof protection if the case is
cracked or broken, or the device has been dropped.
Contact your Icom distributor or your dealer for advice.
–3 –– 2 –
■Precautions
RWARNING! NEVER connect the device directly to an AC
outlet. This may cause a re or an electric shock.
RWARNING! NEVER connect the device to a power
source of more than 16 V DC such as a 24 V battery. This
connection could cause a re or damage the device.
RWARNING! NEVER reverse the DC power cable polarity.
This could cause a re or damage the equipment.
RWARNING! NEVER cut the DC power cable between
the DC power connector and the fuse holder. If an incorrect
connection is made after cutting, the device may be
damaged.
RWARNING! NEVER operate the device during a lightning
storm. It may result in an electric shock, cause a re or
damage the device. Always disconnect the power source
and other connectors before a storm.
RWARNING! NEVER place the device where normal
operation of the vessel may be hindered, or where it could
cause bodily injury.
CAUTION: DO NOT use or leave the device in areas with
temperatures below –20°C ~ +60°C (–4ºF ~ +140ºF), or in
areas subject to direct sunlight, such as a dashboard.
CAUTION: DO NOT use harsh solvents such as Benzine or
alcohol when cleaning. This could damage the equipment
surfaces. If the surface becomes dusty or dirty, wipe it clean
with a soft, dry cloth.
NEVER place the device in an insecure place to avoid
inadvertent use by unauthorized persons.
BE CAREFUL! The device’s rear panel may become hot
when continuously using for long periods of time.
BE CAREFUL! The device meets IPX7 requirements for
waterproof protection*. However, once the device has been
dropped, or the waterproof seal is cracked or damaged,
waterproof protection cannot be guaranteed because of
possible damage to the case or the waterproof seal.
* Except for the DC power connector and AF Out leads.
NOTE: Install the device more than 1 meter from the
vessel’s magnetic navigation compass.
NOTE: Install the device within approximately 15 meters
from the transceiver or an existing access point, and in a
place where there are no obstacles between the device and
the transceiver.
■Précautions
RAVERTISSEMENT ! NE JAMAIS relier l’appareil à une prise
CA. Cela pourrait provoquer un choc électrique ou un incendie.
RAVERTISSEMENT ! NE JAMAIS brancher l’appareil sur
une source d’alimentation supérieure à 16 V CC, comme
une batterie de 24 V. Cela pourrait endommager l’appareil.
RAVERTISSEMENT ! NE JAMAIS inverser la polarité du
câble d’alimentation CC lors de la connexion à une source
d’alimentation. Cela pourrait endommager l’émetteur-récepteur.
RAVERTISSEMENT ! NE JAMAIS couper le câble d’alimentation
CC entre la prise CC et le porte-fusible. L’appareil peut être
endommagé par la suite en cas de connexion inappropriée.
RAVERTISSEMENT ! NE JAMAIS utiliser l’appareil durant
un orage. Cela risquerait de provoquer un choc électrique, un
incendie ou d’endommager l’appareil. Toujours débrancher la
source d’alimentation et autre connecteurs avant une tempête.
RAVERTISSEMENT ! NE JAMAIS installer l’appareil à un
emplacement où il pourrait gêner le fonctionnement normal
du navire ou provoquer des blessures corporelles.
MISE EN GARDE : NE PAS utiliser ou placer l’appareil
dans des zones où la temperature est inférieure à –20°
ou supérieure à +60° ou dans des zones soumises au
rayonnement solaire direct, telles le tableau de bord.
MISE EN GARDE : NE PAS utiliser de dissolvants agressifs
tels que du Benzène ou de l’alcool lors du nettoyage, car ils
endommageraient les surfaces de l’appareil. Si l’appareil est
poussiéreux ou sale, nettoyez-le avec un tissu doux et sec.
NE placez JAMAIS l’appareil dans un endroit non sécurisé
pour éviter toute utilisation par des personnes non autorisées.
MISE EN GARDE : La face arrière de l’appareil chaue en
cas d’utilisation continue sur une longue durée.
MISE EN GARDE : L’appareil est étanche conformément
à la norme IPX7*. L’étanchéité ne peut plus être garantie
après une chute de l’appareil en raison des risques de
ssures du boîtier, de dégradation du joint d’étanchéité, etc.
* Les connecteurs sur le panneau arrière ne sont pas étanche IPX7.
REMARQUE : Installer l’appareil à au moins 1 m du compas
de route du navire.
REMARQUE : Installez l'appareil à environ 15 mètres de l'émetteur-
récepteur ou d’un point d’accès existant et dans un endroit où il n'y
a aucun obstacle entre l'appareil et l'émetteur-récepteur.
Si l’appareil avant est exposé à de l'eau de mer, ASSUREZ-
VOUS DE LE NETTOYER ENTIEREMENT AVEC DE
L'EAU DOUCE lorsque la protection étanche sur l’appareil
avant fonctionne. Dans le cas contraire, les touches risquent
de ne plus fonctionner en raison de la cristallisation du sel.
■Disposal
The crossed-out wheeled-bin symbol on your
product, literature, or packaging reminds you
that in the European Union, all electrical and
electronic products, batteries, and
accumulators (rechargeable batteries) must be
taken to designated collection locations at the
end of their working life. Do not dispose of these products
as unsorted municipal waste. Dispose of them according to
the laws in your area.
■About CE and DOC
Hereby, Icom Inc. declares that the versions of
CT-M500 which have the “CE” symbol on the
product, comply with the essential requirements
of the Radio Equipment Directive, 2014/53/EU,
and the restriction of the use of certain hazardous
substances in electrical and electronic equipment Directive,
2011/65/EU. The full text of the EU declaration of conformity
is available at the following internet address:
https://www.icomjapan.com/support/
■Panel description
34
1 2
78
6
5
DFront panel
1STATUS INDICATOR
Blinks green: Searching the transceiver.
Lights green: Connecting to the transceiver.
Lights red: Entering the WLAN Setup mode and
waiting until the transceiver sets the
WLAN setting.
2POWER INDICATOR
Lights blue when the device is turned ON.
3POWER KEY [ ]
Hold down for 1 second to turn the device ON or OFF.
LThe device automatically connects to the transceiver.
LIf the WLAN setting is not set, the device enters the WLAN
Setup mode and waits until the transceiver sets the WLAN
setting.
4RESET KEY [RESET]
Hold down [RESET] for 3 seconds when the device is
turned ON to reset the WLAN setting.
LThe Status indicator blinks red while holding down [RESET].
LThe device also restarts in the WLAN Setup mode and waits
until the transceiver sets the WLAN setting.
DRear panel
5AF OUT LEADS
Connects to an External Horn Speaker.
Blue: External Horn Speaker (+)
Gray: External Horn Speaker (–)
Black, Orange: NC (Disconnected)
NOTE: The connectors are attached to keep the leads
together. Before connecting to a piece of equipment, cut
the leads to remove the connector.
6DC POWER CONNECTOR
Connects to a 13.8 V DC power source.
(+: Red, –: Black)
7NMEA 2000 CONNECTOR
Connects to an NMEA 2000 network.
8GROUND TERMINAL
Connects to a vessel ground to prevent electrical shocks
and interference from other equipment occurring.
Use a PH M3 × 6 screw (user supplied).
CAUTION: After connecting the DC power cable and AF
Out leads, cover the connector and leads with an adhesive
tape, as shown below, to prevent water seeping into the
connection.
Rubber vulcanizing tape
■Supplied accessories
Mounting bracket DC power cable
(OPC-2472)
For the mounting bracket
Spring washers (M5)
Flat washers (M5)
Screws
(5 × 20 mm)
Screws
(5 × 6 mm)
■Electromagnetic Interference
When you use a Wireless LAN, pay attention to the following:
Wireless LAN products operate in the 2.4 GHz band.
The 2.4 GHz band is also used by other devices, such
as Bluetooth devices, microwave ovens, RFID systems,
amateur radio stations, and so on.
When using this device near such devices, interference may
occur, causing a decrease in communication speed, and an
unstable connection. In such cases, use this device away
from the other devices, or stop using those devices.
IC-M510 and CT-M500 RF Safety warning
An internal Wireless LAN module and an antenna are
supplied with the IC-M510 and CT-M500.
To comply with FCC/ISED RF Exposure for the installed
Wireless LAN unit, the device should be installed and
operated with a minimum distance of 20 cm between the
device and all persons. No other transmitting antenna is
permitted to be located within 20 cm of the device.
Avertissement de sécurité RF IC-M510 et CT-M500
Un module LAN sans l interne et une antenne sont fournis
avec l'IC-M510 et le CT-M500.
Pour se conformer à l'exposition aux RF FCC / ISED pour
l'unité LAN sans l installée, l'appareil doit être installé et
utilisé à une distance minimale de 20 cm entre l'appareil
et toutes les personnes. Aucune autre antenne d'émission
n'est autorisée à être située à moins de 20 cm de l'appareil.
–3 –– 2 –
■Precautions
RWARNING! NEVER connect the device directly to an AC
outlet. This may cause a re or an electric shock.
RWARNING! NEVER connect the device to a power
source of more than 16 V DC such as a 24 V battery. This
connection could cause a re or damage the device.
RWARNING! NEVER reverse the DC power cable polarity.
This could cause a re or damage the equipment.
RWARNING! NEVER cut the DC power cable between
the DC power connector and the fuse holder. If an incorrect
connection is made after cutting, the device may be
damaged.
RWARNING! NEVER operate the device during a lightning
storm. It may result in an electric shock, cause a re or
damage the device. Always disconnect the power source
and other connectors before a storm.
RWARNING! NEVER place the device where normal
operation of the vessel may be hindered, or where it could
cause bodily injury.
CAUTION: DO NOT use or leave the device in areas with
temperatures below –20°C ~ +60°C (–4ºF ~ +140ºF), or in
areas subject to direct sunlight, such as a dashboard.
CAUTION: DO NOT use harsh solvents such as Benzine or
alcohol when cleaning. This could damage the equipment
surfaces. If the surface becomes dusty or dirty, wipe it clean
with a soft, dry cloth.
NEVER place the device in an insecure place to avoid
inadvertent use by unauthorized persons.
BE CAREFUL! The device’s rear panel may become hot
when continuously using for long periods of time.
BE CAREFUL! The device meets IPX7 requirements for
waterproof protection*. However, once the device has been
dropped, or the waterproof seal is cracked or damaged,
waterproof protection cannot be guaranteed because of
possible damage to the case or the waterproof seal.
* Except for the DC power connector and AF Out leads.
NOTE: Install the device more than 1 meter from the
vessel’s magnetic navigation compass.
NOTE: Install the device within approximately 15 meters
from the transceiver or an existing access point, and in a
place where there are no obstacles between the device and
the transceiver.
■Précautions
RAVERTISSEMENT ! NE JAMAIS relier l’appareil à une prise
CA. Cela pourrait provoquer un choc électrique ou un incendie.
RAVERTISSEMENT ! NE JAMAIS brancher l’appareil sur
une source d’alimentation supérieure à 16 V CC, comme
une batterie de 24 V. Cela pourrait endommager l’appareil.
RAVERTISSEMENT ! NE JAMAIS inverser la polarité du
câble d’alimentation CC lors de la connexion à une source
d’alimentation. Cela pourrait endommager l’émetteur-récepteur.
RAVERTISSEMENT ! NE JAMAIS couper le câble d’alimentation
CC entre la prise CC et le porte-fusible. L’appareil peut être
endommagé par la suite en cas de connexion inappropriée.
RAVERTISSEMENT ! NE JAMAIS utiliser l’appareil durant
un orage. Cela risquerait de provoquer un choc électrique, un
incendie ou d’endommager l’appareil. Toujours débrancher la
source d’alimentation et autre connecteurs avant une tempête.
RAVERTISSEMENT ! NE JAMAIS installer l’appareil à un
emplacement où il pourrait gêner le fonctionnement normal
du navire ou provoquer des blessures corporelles.
MISE EN GARDE : NE PAS utiliser ou placer l’appareil
dans des zones où la temperature est inférieure à –20°
ou supérieure à +60° ou dans des zones soumises au
rayonnement solaire direct, telles le tableau de bord.
MISE EN GARDE : NE PAS utiliser de dissolvants agressifs
tels que du Benzène ou de l’alcool lors du nettoyage, car ils
endommageraient les surfaces de l’appareil. Si l’appareil est
poussiéreux ou sale, nettoyez-le avec un tissu doux et sec.
NE placez JAMAIS l’appareil dans un endroit non sécurisé
pour éviter toute utilisation par des personnes non autorisées.
MISE EN GARDE : La face arrière de l’appareil chaue en
cas d’utilisation continue sur une longue durée.
MISE EN GARDE : L’appareil est étanche conformément
à la norme IPX7*. L’étanchéité ne peut plus être garantie
après une chute de l’appareil en raison des risques de
ssures du boîtier, de dégradation du joint d’étanchéité, etc.
* Les connecteurs sur le panneau arrière ne sont pas étanche IPX7.
REMARQUE : Installer l’appareil à au moins 1 m du compas
de route du navire.
REMARQUE : Installez l'appareil à environ 15 mètres de l'émetteur-
récepteur ou d’un point d’accès existant et dans un endroit où il n'y
a aucun obstacle entre l'appareil et l'émetteur-récepteur.
Si l’appareil avant est exposé à de l'eau de mer, ASSUREZ-
VOUS DE LE NETTOYER ENTIEREMENT AVEC DE
L'EAU DOUCE lorsque la protection étanche sur l’appareil
avant fonctionne. Dans le cas contraire, les touches risquent
de ne plus fonctionner en raison de la cristallisation du sel.
■Disposal
The crossed-out wheeled-bin symbol on your
product, literature, or packaging reminds you
that in the European Union, all electrical and
electronic products, batteries, and
accumulators (rechargeable batteries) must be
taken to designated collection locations at the
end of their working life. Do not dispose of these products
as unsorted municipal waste. Dispose of them according to
the laws in your area.
■About CE and DOC
Hereby, Icom Inc. declares that the versions of
CT-M500 which have the “CE” symbol on the
product, comply with the essential requirements
of the Radio Equipment Directive, 2014/53/EU,
and the restriction of the use of certain hazardous
substances in electrical and electronic equipment Directive,
2011/65/EU. The full text of the EU declaration of conformity
is available at the following internet address:
https://www.icomjapan.com/support/
■Panel description
34
1 2
78
6
5
DFront panel
1STATUS INDICATOR
Blinks green: Searching the transceiver.
Lights green: Connecting to the transceiver.
Lights red: Entering the WLAN Setup mode and
waiting until the transceiver sets the
WLAN setting.
2POWER INDICATOR
Lights blue when the device is turned ON.
3POWER KEY [ ]
Hold down for 1 second to turn the device ON or OFF.
LThe device automatically connects to the transceiver.
LIf the WLAN setting is not set, the device enters the WLAN
Setup mode and waits until the transceiver sets the WLAN
setting.
4RESET KEY [RESET]
Hold down [RESET] for 3 seconds when the device is
turned ON to reset the WLAN setting.
LThe Status indicator blinks red while holding down [RESET].
LThe device also restarts in the WLAN Setup mode and waits
until the transceiver sets the WLAN setting.
DRear panel
5AF OUT LEADS
Connects to an External Horn Speaker.
Blue: External Horn Speaker (+)
Gray: External Horn Speaker (–)
Black, Orange: NC (Disconnected)
NOTE: The connectors are attached to keep the leads
together. Before connecting to a piece of equipment, cut
the leads to remove the connector.
6DC POWER CONNECTOR
Connects to a 13.8 V DC power source.
(+: Red, –: Black)
7NMEA 2000 CONNECTOR
Connects to an NMEA 2000 network.
8GROUND TERMINAL
Connects to a vessel ground to prevent electrical shocks
and interference from other equipment occurring.
Use a PH M3 × 6 screw (user supplied).
CAUTION: After connecting the DC power cable and AF
Out leads, cover the connector and leads with an adhesive
tape, as shown below, to prevent water seeping into the
connection.
Rubber vulcanizing tape
■Supplied accessories
Mounting bracket DC power cable
(OPC-2472)
For the mounting bracket
Spring washers (M5)
Flat washers (M5)
Screws
(5 × 20 mm)
Screws
(5 × 6 mm)
■Electromagnetic Interference
When you use a Wireless LAN, pay attention to the following:
Wireless LAN products operate in the 2.4 GHz band.
The 2.4 GHz band is also used by other devices, such
as Bluetooth devices, microwave ovens, RFID systems,
amateur radio stations, and so on.
When using this device near such devices, interference may
occur, causing a decrease in communication speed, and an
unstable connection. In such cases, use this device away
from the other devices, or stop using those devices.
IC-M510 and CT-M500 RF Safety warning
An internal Wireless LAN module and an antenna are
supplied with the IC-M510 and CT-M500.
To comply with FCC/ISED RF Exposure for the installed
Wireless LAN unit, the device should be installed and
operated with a minimum distance of 20 cm between the
device and all persons. No other transmitting antenna is
permitted to be located within 20 cm of the device.
Avertissement de sécurité RF IC-M510 et CT-M500
Un module LAN sans l interne et une antenne sont fournis
avec l'IC-M510 et le CT-M500.
Pour se conformer à l'exposition aux RF FCC / ISED pour
l'unité LAN sans l installée, l'appareil doit être installé et
utilisé à une distance minimale de 20 cm entre l'appareil
et toutes les personnes. Aucune autre antenne d'émission
n'est autorisée à être située à moins de 20 cm de l'appareil.
–3 –– 2 –
■Precautions
RWARNING! NEVER connect the device directly to an AC
outlet. This may cause a re or an electric shock.
RWARNING! NEVER connect the device to a power
source of more than 16 V DC such as a 24 V battery. This
connection could cause a re or damage the device.
RWARNING! NEVER reverse the DC power cable polarity.
This could cause a re or damage the equipment.
RWARNING! NEVER cut the DC power cable between
the DC power connector and the fuse holder. If an incorrect
connection is made after cutting, the device may be
damaged.
RWARNING! NEVER operate the device during a lightning
storm. It may result in an electric shock, cause a re or
damage the device. Always disconnect the power source
and other connectors before a storm.
RWARNING! NEVER place the device where normal
operation of the vessel may be hindered, or where it could
cause bodily injury.
CAUTION: DO NOT use or leave the device in areas with
temperatures below –20°C ~ +60°C (–4ºF ~ +140ºF), or in
areas subject to direct sunlight, such as a dashboard.
CAUTION: DO NOT use harsh solvents such as Benzine or
alcohol when cleaning. This could damage the equipment
surfaces. If the surface becomes dusty or dirty, wipe it clean
with a soft, dry cloth.
NEVER place the device in an insecure place to avoid
inadvertent use by unauthorized persons.
BE CAREFUL! The device’s rear panel may become hot
when continuously using for long periods of time.
BE CAREFUL! The device meets IPX7 requirements for
waterproof protection*. However, once the device has been
dropped, or the waterproof seal is cracked or damaged,
waterproof protection cannot be guaranteed because of
possible damage to the case or the waterproof seal.
* Except for the DC power connector and AF Out leads.
NOTE: Install the device more than 1 meter from the
vessel’s magnetic navigation compass.
NOTE: Install the device within approximately 15 meters
from the transceiver or an existing access point, and in a
place where there are no obstacles between the device and
the transceiver.
■Précautions
RAVERTISSEMENT ! NE JAMAIS relier l’appareil à une prise
CA. Cela pourrait provoquer un choc électrique ou un incendie.
RAVERTISSEMENT ! NE JAMAIS brancher l’appareil sur
une source d’alimentation supérieure à 16 V CC, comme
une batterie de 24 V. Cela pourrait endommager l’appareil.
RAVERTISSEMENT ! NE JAMAIS inverser la polarité du
câble d’alimentation CC lors de la connexion à une source
d’alimentation. Cela pourrait endommager l’émetteur-récepteur.
RAVERTISSEMENT ! NE JAMAIS couper le câble d’alimentation
CC entre la prise CC et le porte-fusible. L’appareil peut être
endommagé par la suite en cas de connexion inappropriée.
RAVERTISSEMENT ! NE JAMAIS utiliser l’appareil durant
un orage. Cela risquerait de provoquer un choc électrique, un
incendie ou d’endommager l’appareil. Toujours débrancher la
source d’alimentation et autre connecteurs avant une tempête.
RAVERTISSEMENT ! NE JAMAIS installer l’appareil à un
emplacement où il pourrait gêner le fonctionnement normal
du navire ou provoquer des blessures corporelles.
MISE EN GARDE : NE PAS utiliser ou placer l’appareil
dans des zones où la temperature est inférieure à –20°
ou supérieure à +60° ou dans des zones soumises au
rayonnement solaire direct, telles le tableau de bord.
MISE EN GARDE : NE PAS utiliser de dissolvants agressifs
tels que du Benzène ou de l’alcool lors du nettoyage, car ils
endommageraient les surfaces de l’appareil. Si l’appareil est
poussiéreux ou sale, nettoyez-le avec un tissu doux et sec.
NE placez JAMAIS l’appareil dans un endroit non sécurisé
pour éviter toute utilisation par des personnes non autorisées.
MISE EN GARDE : La face arrière de l’appareil chaue en
cas d’utilisation continue sur une longue durée.
MISE EN GARDE : L’appareil est étanche conformément
à la norme IPX7*. L’étanchéité ne peut plus être garantie
après une chute de l’appareil en raison des risques de
ssures du boîtier, de dégradation du joint d’étanchéité, etc.
* Les connecteurs sur le panneau arrière ne sont pas étanche IPX7.
REMARQUE : Installer l’appareil à au moins 1 m du compas
de route du navire.
REMARQUE : Installez l'appareil à environ 15 mètres de l'émetteur-
récepteur ou d’un point d’accès existant et dans un endroit où il n'y
a aucun obstacle entre l'appareil et l'émetteur-récepteur.
Si l’appareil avant est exposé à de l'eau de mer, ASSUREZ-
VOUS DE LE NETTOYER ENTIEREMENT AVEC DE
L'EAU DOUCE lorsque la protection étanche sur l’appareil
avant fonctionne. Dans le cas contraire, les touches risquent
de ne plus fonctionner en raison de la cristallisation du sel.
■Disposal
The crossed-out wheeled-bin symbol on your
product, literature, or packaging reminds you
that in the European Union, all electrical and
electronic products, batteries, and
accumulators (rechargeable batteries) must be
taken to designated collection locations at the
end of their working life. Do not dispose of these products
as unsorted municipal waste. Dispose of them according to
the laws in your area.
■About CE and DOC
Hereby, Icom Inc. declares that the versions of
CT-M500 which have the “CE” symbol on the
product, comply with the essential requirements
of the Radio Equipment Directive, 2014/53/EU,
and the restriction of the use of certain hazardous
substances in electrical and electronic equipment Directive,
2011/65/EU. The full text of the EU declaration of conformity
is available at the following internet address:
https://www.icomjapan.com/support/
■Panel description
34
1 2
78
6
5
DFront panel
1STATUS INDICATOR
Blinks green: Searching the transceiver.
Lights green: Connecting to the transceiver.
Lights red: Entering the WLAN Setup mode and
waiting until the transceiver sets the
WLAN setting.
2POWER INDICATOR
Lights blue when the device is turned ON.
3POWER KEY [ ]
Hold down for 1 second to turn the device ON or OFF.
LThe device automatically connects to the transceiver.
LIf the WLAN setting is not set, the device enters the WLAN
Setup mode and waits until the transceiver sets the WLAN
setting.
4RESET KEY [RESET]
Hold down [RESET] for 3 seconds when the device is
turned ON to reset the WLAN setting.
LThe Status indicator blinks red while holding down [RESET].
LThe device also restarts in the WLAN Setup mode and waits
until the transceiver sets the WLAN setting.
DRear panel
5AF OUT LEADS
Connects to an External Horn Speaker.
Blue: External Horn Speaker (+)
Gray: External Horn Speaker (–)
Black, Orange: NC (Disconnected)
NOTE: The connectors are attached to keep the leads
together. Before connecting to a piece of equipment, cut
the leads to remove the connector.
6DC POWER CONNECTOR
Connects to a 13.8 V DC power source.
(+: Red, –: Black)
7NMEA 2000 CONNECTOR
Connects to an NMEA 2000 network.
8GROUND TERMINAL
Connects to a vessel ground to prevent electrical shocks
and interference from other equipment occurring.
Use a PH M3 × 6 screw (user supplied).
CAUTION: After connecting the DC power cable and AF
Out leads, cover the connector and leads with an adhesive
tape, as shown below, to prevent water seeping into the
connection.
Rubber vulcanizing tape
■Supplied accessories
Mounting bracket DC power cable
(OPC-2472)
For the mounting bracket
Spring washers (M5)
Flat washers (M5)
Screws
(5 × 20 mm)
Screws
(5 × 6 mm)
■Electromagnetic Interference
When you use a Wireless LAN, pay attention to the following:
Wireless LAN products operate in the 2.4 GHz band.
The 2.4 GHz band is also used by other devices, such
as Bluetooth devices, microwave ovens, RFID systems,
amateur radio stations, and so on.
When using this device near such devices, interference may
occur, causing a decrease in communication speed, and an
unstable connection. In such cases, use this device away
from the other devices, or stop using those devices.
IC-M510 and CT-M500 RF Safety warning
An internal Wireless LAN module and an antenna are
supplied with the IC-M510 and CT-M500.
To comply with FCC/ISED RF Exposure for the installed
Wireless LAN unit, the device should be installed and
operated with a minimum distance of 20 cm between the
device and all persons. No other transmitting antenna is
permitted to be located within 20 cm of the device.
Avertissement de sécurité RF IC-M510 et CT-M500
Un module LAN sans l interne et une antenne sont fournis
avec l'IC-M510 et le CT-M500.
Pour se conformer à l'exposition aux RF FCC / ISED pour
l'unité LAN sans l installée, l'appareil doit être installé et
utilisé à une distance minimale de 20 cm entre l'appareil
et toutes les personnes. Aucune autre antenne d'émission
n'est autorisée à être située à moins de 20 cm de l'appareil.
–3 –– 2 –
■Precautions
RWARNING! NEVER connect the device directly to an AC
outlet. This may cause a re or an electric shock.
RWARNING! NEVER connect the device to a power
source of more than 16 V DC such as a 24 V battery. This
connection could cause a re or damage the device.
RWARNING! NEVER reverse the DC power cable polarity.
This could cause a re or damage the equipment.
RWARNING! NEVER cut the DC power cable between
the DC power connector and the fuse holder. If an incorrect
connection is made after cutting, the device may be
damaged.
RWARNING! NEVER operate the device during a lightning
storm. It may result in an electric shock, cause a re or
damage the device. Always disconnect the power source
and other connectors before a storm.
RWARNING! NEVER place the device where normal
operation of the vessel may be hindered, or where it could
cause bodily injury.
CAUTION: DO NOT use or leave the device in areas with
temperatures below –20°C ~ +60°C (–4ºF ~ +140ºF), or in
areas subject to direct sunlight, such as a dashboard.
CAUTION: DO NOT use harsh solvents such as Benzine or
alcohol when cleaning. This could damage the equipment
surfaces. If the surface becomes dusty or dirty, wipe it clean
with a soft, dry cloth.
NEVER place the device in an insecure place to avoid
inadvertent use by unauthorized persons.
BE CAREFUL! The device’s rear panel may become hot
when continuously using for long periods of time.
BE CAREFUL! The device meets IPX7 requirements for
waterproof protection*. However, once the device has been
dropped, or the waterproof seal is cracked or damaged,
waterproof protection cannot be guaranteed because of
possible damage to the case or the waterproof seal.
* Except for the DC power connector and AF Out leads.
NOTE: Install the device more than 1 meter from the
vessel’s magnetic navigation compass.
NOTE: Install the device within approximately 15 meters
from the transceiver or an existing access point, and in a
place where there are no obstacles between the device and
the transceiver.
■Précautions
RAVERTISSEMENT ! NE JAMAIS relier l’appareil à une prise
CA. Cela pourrait provoquer un choc électrique ou un incendie.
RAVERTISSEMENT ! NE JAMAIS brancher l’appareil sur
une source d’alimentation supérieure à 16 V CC, comme
une batterie de 24 V. Cela pourrait endommager l’appareil.
RAVERTISSEMENT ! NE JAMAIS inverser la polarité du
câble d’alimentation CC lors de la connexion à une source
d’alimentation. Cela pourrait endommager l’émetteur-récepteur.
RAVERTISSEMENT ! NE JAMAIS couper le câble d’alimentation
CC entre la prise CC et le porte-fusible. L’appareil peut être
endommagé par la suite en cas de connexion inappropriée.
RAVERTISSEMENT ! NE JAMAIS utiliser l’appareil durant
un orage. Cela risquerait de provoquer un choc électrique, un
incendie ou d’endommager l’appareil. Toujours débrancher la
source d’alimentation et autre connecteurs avant une tempête.
RAVERTISSEMENT ! NE JAMAIS installer l’appareil à un
emplacement où il pourrait gêner le fonctionnement normal
du navire ou provoquer des blessures corporelles.
MISE EN GARDE : NE PAS utiliser ou placer l’appareil
dans des zones où la temperature est inférieure à –20°
ou supérieure à +60° ou dans des zones soumises au
rayonnement solaire direct, telles le tableau de bord.
MISE EN GARDE : NE PAS utiliser de dissolvants agressifs
tels que du Benzène ou de l’alcool lors du nettoyage, car ils
endommageraient les surfaces de l’appareil. Si l’appareil est
poussiéreux ou sale, nettoyez-le avec un tissu doux et sec.
NE placez JAMAIS l’appareil dans un endroit non sécurisé
pour éviter toute utilisation par des personnes non autorisées.
MISE EN GARDE : La face arrière de l’appareil chaue en
cas d’utilisation continue sur une longue durée.
MISE EN GARDE : L’appareil est étanche conformément
à la norme IPX7*. L’étanchéité ne peut plus être garantie
après une chute de l’appareil en raison des risques de
ssures du boîtier, de dégradation du joint d’étanchéité, etc.
* Les connecteurs sur le panneau arrière ne sont pas étanche IPX7.
REMARQUE : Installer l’appareil à au moins 1 m du compas
de route du navire.
REMARQUE : Installez l'appareil à environ 15 mètres de l'émetteur-
récepteur ou d’un point d’accès existant et dans un endroit où il n'y
a aucun obstacle entre l'appareil et l'émetteur-récepteur.
Si l’appareil avant est exposé à de l'eau de mer, ASSUREZ-
VOUS DE LE NETTOYER ENTIEREMENT AVEC DE
L'EAU DOUCE lorsque la protection étanche sur l’appareil
avant fonctionne. Dans le cas contraire, les touches risquent
de ne plus fonctionner en raison de la cristallisation du sel.
■Disposal
The crossed-out wheeled-bin symbol on your
product, literature, or packaging reminds you
that in the European Union, all electrical and
electronic products, batteries, and
accumulators (rechargeable batteries) must be
taken to designated collection locations at the
end of their working life. Do not dispose of these products
as unsorted municipal waste. Dispose of them according to
the laws in your area.
■About CE and DOC
Hereby, Icom Inc. declares that the versions of
CT-M500 which have the “CE” symbol on the
product, comply with the essential requirements
of the Radio Equipment Directive, 2014/53/EU,
and the restriction of the use of certain hazardous
substances in electrical and electronic equipment Directive,
2011/65/EU. The full text of the EU declaration of conformity
is available at the following internet address:
https://www.icomjapan.com/support/
■Panel description
34
1 2
78
6
5
DFront panel
1STATUS INDICATOR
Blinks green: Searching the transceiver.
Lights green: Connecting to the transceiver.
Lights red: Entering the WLAN Setup mode and
waiting until the transceiver sets the
WLAN setting.
2POWER INDICATOR
Lights blue when the device is turned ON.
3POWER KEY [ ]
Hold down for 1 second to turn the device ON or OFF.
LThe device automatically connects to the transceiver.
LIf the WLAN setting is not set, the device enters the WLAN
Setup mode and waits until the transceiver sets the WLAN
setting.
4RESET KEY [RESET]
Hold down [RESET] for 3 seconds when the device is
turned ON to reset the WLAN setting.
LThe Status indicator blinks red while holding down [RESET].
LThe device also restarts in the WLAN Setup mode and waits
until the transceiver sets the WLAN setting.
DRear panel
5AF OUT LEADS
Connects to an External Horn Speaker.
Blue: External Horn Speaker (+)
Gray: External Horn Speaker (–)
Black, Orange: NC (Disconnected)
NOTE: The connectors are attached to keep the leads
together. Before connecting to a piece of equipment, cut
the leads to remove the connector.
6DC POWER CONNECTOR
Connects to a 13.8 V DC power source.
(+: Red, –: Black)
7NMEA 2000 CONNECTOR
Connects to an NMEA 2000 network.
8GROUND TERMINAL
Connects to a vessel ground to prevent electrical shocks
and interference from other equipment occurring.
Use a PH M3 × 6 screw (user supplied).
CAUTION: After connecting the DC power cable and AF
Out leads, cover the connector and leads with an adhesive
tape, as shown below, to prevent water seeping into the
connection.
Rubber vulcanizing tape
■Supplied accessories
Mounting bracket DC power cable
(OPC-2472)
For the mounting bracket
Spring washers (M5)
Flat washers (M5)
Screws
(5 × 20 mm)
Screws
(5 × 6 mm)
■Electromagnetic Interference
When you use a Wireless LAN, pay attention to the following:
Wireless LAN products operate in the 2.4 GHz band.
The 2.4 GHz band is also used by other devices, such
as Bluetooth devices, microwave ovens, RFID systems,
amateur radio stations, and so on.
When using this device near such devices, interference may
occur, causing a decrease in communication speed, and an
unstable connection. In such cases, use this device away
from the other devices, or stop using those devices.
IC-M510 and CT-M500 RF Safety warning
An internal Wireless LAN module and an antenna are
supplied with the IC-M510 and CT-M500.
To comply with FCC/ISED RF Exposure for the installed
Wireless LAN unit, the device should be installed and
operated with a minimum distance of 20 cm between the
device and all persons. No other transmitting antenna is
permitted to be located within 20 cm of the device.
Avertissement de sécurité RF IC-M510 et CT-M500
Un module LAN sans l interne et une antenne sont fournis
avec l'IC-M510 et le CT-M500.
Pour se conformer à l'exposition aux RF FCC / ISED pour
l'unité LAN sans l installée, l'appareil doit être installé et
utilisé à une distance minimale de 20 cm entre l'appareil
et toutes les personnes. Aucune autre antenne d'émission
n'est autorisée à être située à moins de 20 cm de l'appareil.
–3 –– 2 –
■Precautions
RWARNING! NEVER connect the device directly to an AC
outlet. This may cause a re or an electric shock.
RWARNING! NEVER connect the device to a power
source of more than 16 V DC such as a 24 V battery. This
connection could cause a re or damage the device.
RWARNING! NEVER reverse the DC power cable polarity.
This could cause a re or damage the equipment.
RWARNING! NEVER cut the DC power cable between
the DC power connector and the fuse holder. If an incorrect
connection is made after cutting, the device may be
damaged.
RWARNING! NEVER operate the device during a lightning
storm. It may result in an electric shock, cause a re or
damage the device. Always disconnect the power source
and other connectors before a storm.
RWARNING! NEVER place the device where normal
operation of the vessel may be hindered, or where it could
cause bodily injury.
CAUTION: DO NOT use or leave the device in areas with
temperatures below –20°C ~ +60°C (–4ºF ~ +140ºF), or in
areas subject to direct sunlight, such as a dashboard.
CAUTION: DO NOT use harsh solvents such as Benzine or
alcohol when cleaning. This could damage the equipment
surfaces. If the surface becomes dusty or dirty, wipe it clean
with a soft, dry cloth.
NEVER place the device in an insecure place to avoid
inadvertent use by unauthorized persons.
BE CAREFUL! The device’s rear panel may become hot
when continuously using for long periods of time.
BE CAREFUL! The device meets IPX7 requirements for
waterproof protection*. However, once the device has been
dropped, or the waterproof seal is cracked or damaged,
waterproof protection cannot be guaranteed because of
possible damage to the case or the waterproof seal.
* Except for the DC power connector and AF Out leads.
NOTE: Install the device more than 1 meter from the
vessel’s magnetic navigation compass.
NOTE: Install the device within approximately 15 meters
from the transceiver or an existing access point, and in a
place where there are no obstacles between the device and
the transceiver.
■Précautions
RAVERTISSEMENT ! NE JAMAIS relier l’appareil à une prise
CA. Cela pourrait provoquer un choc électrique ou un incendie.
RAVERTISSEMENT ! NE JAMAIS brancher l’appareil sur
une source d’alimentation supérieure à 16 V CC, comme
une batterie de 24 V. Cela pourrait endommager l’appareil.
RAVERTISSEMENT ! NE JAMAIS inverser la polarité du
câble d’alimentation CC lors de la connexion à une source
d’alimentation. Cela pourrait endommager l’émetteur-récepteur.
RAVERTISSEMENT ! NE JAMAIS couper le câble d’alimentation
CC entre la prise CC et le porte-fusible. L’appareil peut être
endommagé par la suite en cas de connexion inappropriée.
RAVERTISSEMENT ! NE JAMAIS utiliser l’appareil durant
un orage. Cela risquerait de provoquer un choc électrique, un
incendie ou d’endommager l’appareil. Toujours débrancher la
source d’alimentation et autre connecteurs avant une tempête.
RAVERTISSEMENT ! NE JAMAIS installer l’appareil à un
emplacement où il pourrait gêner le fonctionnement normal
du navire ou provoquer des blessures corporelles.
MISE EN GARDE : NE PAS utiliser ou placer l’appareil
dans des zones où la temperature est inférieure à –20°
ou supérieure à +60° ou dans des zones soumises au
rayonnement solaire direct, telles le tableau de bord.
MISE EN GARDE : NE PAS utiliser de dissolvants agressifs
tels que du Benzène ou de l’alcool lors du nettoyage, car ils
endommageraient les surfaces de l’appareil. Si l’appareil est
poussiéreux ou sale, nettoyez-le avec un tissu doux et sec.
NE placez JAMAIS l’appareil dans un endroit non sécurisé
pour éviter toute utilisation par des personnes non autorisées.
MISE EN GARDE : La face arrière de l’appareil chaue en
cas d’utilisation continue sur une longue durée.
MISE EN GARDE : L’appareil est étanche conformément
à la norme IPX7*. L’étanchéité ne peut plus être garantie
après une chute de l’appareil en raison des risques de
ssures du boîtier, de dégradation du joint d’étanchéité, etc.
* Les connecteurs sur le panneau arrière ne sont pas étanche IPX7.
REMARQUE : Installer l’appareil à au moins 1 m du compas
de route du navire.
REMARQUE : Installez l'appareil à environ 15 mètres de l'émetteur-
récepteur ou d’un point d’accès existant et dans un endroit où il n'y
a aucun obstacle entre l'appareil et l'émetteur-récepteur.
Si l’appareil avant est exposé à de l'eau de mer, ASSUREZ-
VOUS DE LE NETTOYER ENTIEREMENT AVEC DE
L'EAU DOUCE lorsque la protection étanche sur l’appareil
avant fonctionne. Dans le cas contraire, les touches risquent
de ne plus fonctionner en raison de la cristallisation du sel.
■Disposal
The crossed-out wheeled-bin symbol on your
product, literature, or packaging reminds you
that in the European Union, all electrical and
electronic products, batteries, and
accumulators (rechargeable batteries) must be
taken to designated collection locations at the
end of their working life. Do not dispose of these products
as unsorted municipal waste. Dispose of them according to
the laws in your area.
■About CE and DOC
Hereby, Icom Inc. declares that the versions of
CT-M500 which have the “CE” symbol on the
product, comply with the essential requirements
of the Radio Equipment Directive, 2014/53/EU,
and the restriction of the use of certain hazardous
substances in electrical and electronic equipment Directive,
2011/65/EU. The full text of the EU declaration of conformity
is available at the following internet address:
https://www.icomjapan.com/support/
■Panel description
34
1 2
78
6
5
DFront panel
1STATUS INDICATOR
Blinks green: Searching the transceiver.
Lights green: Connecting to the transceiver.
Lights red: Entering the WLAN Setup mode and
waiting until the transceiver sets the
WLAN setting.
2POWER INDICATOR
Lights blue when the device is turned ON.
3POWER KEY [ ]
Hold down for 1 second to turn the device ON or OFF.
LThe device automatically connects to the transceiver.
LIf the WLAN setting is not set, the device enters the WLAN
Setup mode and waits until the transceiver sets the WLAN
setting.
4RESET KEY [RESET]
Hold down [RESET] for 3 seconds when the device is
turned ON to reset the WLAN setting.
LThe Status indicator blinks red while holding down [RESET].
LThe device also restarts in the WLAN Setup mode and waits
until the transceiver sets the WLAN setting.
DRear panel
5AF OUT LEADS
Connects to an External Horn Speaker.
Blue: External Horn Speaker (+)
Gray: External Horn Speaker (–)
Black, Orange: NC (Disconnected)
NOTE: The connectors are attached to keep the leads
together. Before connecting to a piece of equipment, cut
the leads to remove the connector.
6DC POWER CONNECTOR
Connects to a 13.8 V DC power source.
(+: Red, –: Black)
7NMEA 2000 CONNECTOR
Connects to an NMEA 2000 network.
8GROUND TERMINAL
Connects to a vessel ground to prevent electrical shocks
and interference from other equipment occurring.
Use a PH M3 × 6 screw (user supplied).
CAUTION: After connecting the DC power cable and AF
Out leads, cover the connector and leads with an adhesive
tape, as shown below, to prevent water seeping into the
connection.
Rubber vulcanizing tape
■Supplied accessories
Mounting bracket DC power cable
(OPC-2472)
For the mounting bracket
Spring washers (M5)
Flat washers (M5)
Screws
(5 × 20 mm)
Screws
(5 × 6 mm)
■Electromagnetic Interference
When you use a Wireless LAN, pay attention to the following:
Wireless LAN products operate in the 2.4 GHz band.
The 2.4 GHz band is also used by other devices, such
as Bluetooth devices, microwave ovens, RFID systems,
amateur radio stations, and so on.
When using this device near such devices, interference may
occur, causing a decrease in communication speed, and an
unstable connection. In such cases, use this device away
from the other devices, or stop using those devices.
IC-M510 and CT-M500 RF Safety warning
An internal Wireless LAN module and an antenna are
supplied with the IC-M510 and CT-M500.
To comply with FCC/ISED RF Exposure for the installed
Wireless LAN unit, the device should be installed and
operated with a minimum distance of 20 cm between the
device and all persons. No other transmitting antenna is
permitted to be located within 20 cm of the device.
Avertissement de sécurité RF IC-M510 et CT-M500
Un module LAN sans l interne et une antenne sont fournis
avec l'IC-M510 et le CT-M500.
Pour se conformer à l'exposition aux RF FCC / ISED pour
l'unité LAN sans l installée, l'appareil doit être installé et
utilisé à une distance minimale de 20 cm entre l'appareil
et toutes les personnes. Aucune autre antenne d'émission
n'est autorisée à être située à moins de 20 cm de l'appareil.
INSTRUCTIONS
EXTERNAL INTERFACE BOX
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Sep. 2021
A7626W-1EX-2 Printed in Japan
© 2021 Icom Inc. –1 –
–4 –
CT-M500
Thank you for choosing this Icom product.
READ ALL INSTRUCTIONS carefully and completely
before using this product.
■Important
SAVE THESE INSTRUCTIONS— These instructions
contain important operating instructions for the CT-M500.
This device connects to a transceiver through a Wireless
LAN (WLAN) and expands the transceiver’s functions.
For the WLAN setting, the functions that you can operate
when connecting to the transceiver, and so on, see the
transceiver’s manual for details.
The transceiver’s manual can be the
following internet address:
https://www.icomjapan.com/support/
LThese instructions are described based on the CT-M500 rmware
version 1.00.
Icom, Icom Inc. and the Icom logo are registered trademarks
of Icom Incorporated (Japan) in Japan, the United States,
the United Kingdom, Germany, France, Spain, Russia,
Australia, New Zealand, and/or other countries.
NMEA 2000 is a trademark of the National Maritime
Electronics Association, Inc.
All other products or brands are registered trademarks or
trademarks of their respective holders.
Icom is not responsible for the destruction, damage to, or
performance of any Icom or non-Icom equipment, if the
malfunction is because of:
• Force majeure, including, but not limited to, res,
earthquakes, storms, oods, lightning, other natural
disasters, disturbances, riots, war, or radioactive
contamination.
• The use of Icom devices with any equipment that is not
manufactured or approved by Icom.
■Explicit denitions
WORD DEFINITION
RWARNING! Personal injury, re hazard or electric shock
may occur.
CAUTION Equipment damage may occur.
NOTE If disregarded, inconvenience only. No risk
of personal injury, re or electric shock.
■Dénitions explicites
TERME DÉFINITION
RAVERTISSEMENT ! Risque de blessures corporelles,
d’incendie ou de choc électrique.
MISE EN GARDE Risque de dégât matériel.
REMARQUE
Inconvénient seulement, en cas de
nonrespect. Absence de risque de
blessures corporelles, d’incendie
ou de choc électrique.
■FCC information
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modications to this device, not expressly
approved by Icom Inc., could void your authority to operate this
device under FCC regulations.
■Information FCC
Cet appareil est conforme à la partie 15 de la réglementation
FCC. Son fonctionnement est soumis à la condition que cet
appareil ne provoque pas d’interférences nocives.
Cet équipement a été testé et reconnu conforme aux limites
xées pour un appareil numérique de classe B, conformément à
la partie 15 de la réglementation FCC. Ces limites ont été xées
an d'assurer une protection raisonnable contre les interférences
nocives dans une installation résidentielle. Cet équipement génère,
utilise et peut émettre un rayonnement de fréquence radio. S'il n'a
pas été installé conformément aux instructions, il peut par ailleurs
créer des interférences perturbant les communications radio.
Toutefois, il n'y a aucune garantie que les interférences ne se
produiront pas dans une installation particulière. Si cet équipement
crée des interférences perturbant la réception de la radio ou de
la télévision, comme cela peut être déterminé en éteignant et en
allumant l'équipement, l'utilisateur est invité à essayer de corriger
l'interférence en prenant une ou plusieurs des mesures ci-après :
• Réorienter ou changer de place l'antenne de réception.
• Éloigner l'équipement et le récepteur.
• Connecter l'équipement sur une prise sur un autre circuit que
celui sur lequel le récepteur est connecté.
• Faire appel au revendeur ou à un technicien radio/TV expérimenté.
MISE EN GARDE : Tout changement ou modication, non
expressément approuvé par Icom Inc., peut annuler l’autorisation de
l’utilisateur à utiliser cet appareil conformément à la réglementation FCC.
■Installing
You can mount the device on a dashboard using the
universal mounting bracket supplied with your device.
CAUTION:
• KEEP the device at least 1 meter (3.3 ft) away from the
vessel’s magnetic navigation compass.
• INSTALL the device within approximately 15 meters
from the transceiver, and in a place where there are no
obstacles between the device and the transceiver.
1. Mount the bracket securely to a surface which is more
than 10 mm thick and can support more than 5 kg using
the 4 supplied screws (5 × 20 mm).
NOTE: When mounting the device on a board, x the
bracket to the board using the user supplied bolts and
nuts, as shown below.
2. Attach the device to the bracket.
Mounting Example
Spring washer
Flat washer
■Specications and options
DSpecications
General
Operating
temperature range –20°C ~ +60°C, –4ºF ~ +140ºF
Power supply
requirement
Negative ground:
13.8 V DC nominal (10.8 ~ 15.9 V)
Current drain
(at 13.8 V) 3.5 A maximum
Dimensions
(approximate)
(projections not
included)
156.5 (W) × 67.6 (H) × 82.1 (D) mm,
6.2 (W) × 2.7 (H) × 3.2 (D) in
Weight
(approximate) 430 g, 15.2 oz
Wireless LAN
Wireless LAN standard
IEEE802.11 b/g/n
Authentication and
Encryption
WEP (64/128 bit),
WPA-PSK (TKIP),
WPA2-PSK (AES)
Channels 1 to 13 (2.4 GHz band)
LMay dier depending on the country of use.
Output power Less than 10 mW/MHz
Hailer
Audio output power More than 25 W into a 4 Ω load
RX Hailer
Audio output power More than 20 W into a 4 Ω load
DOptions
• SP-37 HORN SPEAKER
DDimensions
51 (2)
66.5 (2.6)
192.2 (7.6)
137 (5.4)
156.5 (6.2)
26 (1) 67.6 (2.7)
60.8 (2.4)
84.4 (3.3)21.3 (0.8)
172.2 (6.8)
82.1 (3.2)
Unit: mm (inch)
■Fuse replacement
One fuse is installed in the supplied DC power cable. If the
fuse blows or the device stops functioning, track down the
source of the problem, repair it, and replace the damaged
fuse with a new one of the proper rating.
Fuse rating: 250 V 5 A
Fuse Coding explanation
Fuse Coding: F 250 V 5 A
Fuse Voltage Rating: 250 Volts
Fuse Current Rating: 5 Amperes
■Recommendation
CLEAN THE DEVICE THOROUGHLY WITH FRESH WATER
after exposure to saltwater, and dry it before using. Otherwise, the
device’s keys may become unusable, due to salt crystallization.
NOTE: If the device’s waterproof protection appears defective,
carefully clean it with a soft, damp (fresh water) cloth, then dry it
before operating.
The device may lose its waterproof protection if the case is
cracked or broken, or the device has been dropped.
Contact your Icom distributor or your dealer for advice.
INSTRUCTIONS
EXTERNAL INTERFACE BOX
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Sep. 2021
A7626W-1EX-2 Printed in Japan
© 2021 Icom Inc. –1 –
–4 –
CT-M500
Thank you for choosing this Icom product.
READ ALL INSTRUCTIONS carefully and completely
before using this product.
■Important
SAVE THESE INSTRUCTIONS— These instructions
contain important operating instructions for the CT-M500.
This device connects to a transceiver through a Wireless
LAN (WLAN) and expands the transceiver’s functions.
For the WLAN setting, the functions that you can operate
when connecting to the transceiver, and so on, see the
transceiver’s manual for details.
The transceiver’s manual can be the
following internet address:
https://www.icomjapan.com/support/
LThese instructions are described based on the CT-M500 rmware
version 1.00.
Icom, Icom Inc. and the Icom logo are registered trademarks
of Icom Incorporated (Japan) in Japan, the United States,
the United Kingdom, Germany, France, Spain, Russia,
Australia, New Zealand, and/or other countries.
NMEA 2000 is a trademark of the National Maritime
Electronics Association, Inc.
All other products or brands are registered trademarks or
trademarks of their respective holders.
Icom is not responsible for the destruction, damage to, or
performance of any Icom or non-Icom equipment, if the
malfunction is because of:
• Force majeure, including, but not limited to, res,
earthquakes, storms, oods, lightning, other natural
disasters, disturbances, riots, war, or radioactive
contamination.
• The use of Icom devices with any equipment that is not
manufactured or approved by Icom.
■Explicit denitions
WORD DEFINITION
RWARNING! Personal injury, re hazard or electric shock
may occur.
CAUTION Equipment damage may occur.
NOTE If disregarded, inconvenience only. No risk
of personal injury, re or electric shock.
■Dénitions explicites
TERME DÉFINITION
RAVERTISSEMENT ! Risque de blessures corporelles,
d’incendie ou de choc électrique.
MISE EN GARDE Risque de dégât matériel.
REMARQUE
Inconvénient seulement, en cas de
nonrespect. Absence de risque de
blessures corporelles, d’incendie
ou de choc électrique.
■FCC information
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modications to this device, not expressly
approved by Icom Inc., could void your authority to operate this
device under FCC regulations.
■Information FCC
Cet appareil est conforme à la partie 15 de la réglementation
FCC. Son fonctionnement est soumis à la condition que cet
appareil ne provoque pas d’interférences nocives.
Cet équipement a été testé et reconnu conforme aux limites
xées pour un appareil numérique de classe B, conformément à
la partie 15 de la réglementation FCC. Ces limites ont été xées
an d'assurer une protection raisonnable contre les interférences
nocives dans une installation résidentielle. Cet équipement génère,
utilise et peut émettre un rayonnement de fréquence radio. S'il n'a
pas été installé conformément aux instructions, il peut par ailleurs
créer des interférences perturbant les communications radio.
Toutefois, il n'y a aucune garantie que les interférences ne se
produiront pas dans une installation particulière. Si cet équipement
crée des interférences perturbant la réception de la radio ou de
la télévision, comme cela peut être déterminé en éteignant et en
allumant l'équipement, l'utilisateur est invité à essayer de corriger
l'interférence en prenant une ou plusieurs des mesures ci-après :
• Réorienter ou changer de place l'antenne de réception.
• Éloigner l'équipement et le récepteur.
• Connecter l'équipement sur une prise sur un autre circuit que
celui sur lequel le récepteur est connecté.
• Faire appel au revendeur ou à un technicien radio/TV expérimenté.
MISE EN GARDE : Tout changement ou modication, non
expressément approuvé par Icom Inc., peut annuler l’autorisation de
l’utilisateur à utiliser cet appareil conformément à la réglementation FCC.
■Installing
You can mount the device on a dashboard using the
universal mounting bracket supplied with your device.
CAUTION:
• KEEP the device at least 1 meter (3.3 ft) away from the
vessel’s magnetic navigation compass.
• INSTALL the device within approximately 15 meters
from the transceiver, and in a place where there are no
obstacles between the device and the transceiver.
1. Mount the bracket securely to a surface which is more
than 10 mm thick and can support more than 5 kg using
the 4 supplied screws (5 × 20 mm).
NOTE: When mounting the device on a board, x the
bracket to the board using the user supplied bolts and
nuts, as shown below.
2. Attach the device to the bracket.
Mounting Example
Spring washer
Flat washer
■Specications and options
DSpecications
General
Operating
temperature range –20°C ~ +60°C, –4ºF ~ +140ºF
Power supply
requirement
Negative ground:
13.8 V DC nominal (10.8 ~ 15.9 V)
Current drain
(at 13.8 V) 3.5 A maximum
Dimensions
(approximate)
(projections not
included)
156.5 (W) × 67.6 (H) × 82.1 (D) mm,
6.2 (W) × 2.7 (H) × 3.2 (D) in
Weight
(approximate) 430 g, 15.2 oz
Wireless LAN
Wireless LAN standard
IEEE802.11 b/g/n
Authentication and
Encryption
WEP (64/128 bit),
WPA-PSK (TKIP),
WPA2-PSK (AES)
Channels 1 to 13 (2.4 GHz band)
LMay dier depending on the country of use.
Output power Less than 10 mW/MHz
Hailer
Audio output power More than 25 W into a 4 Ω load
RX Hailer
Audio output power More than 20 W into a 4 Ω load
DOptions
• SP-37 HORN SPEAKER
DDimensions
51 (2)
66.5 (2.6)
192.2 (7.6)
137 (5.4)
156.5 (6.2)
26 (1) 67.6 (2.7)
60.8 (2.4)
84.4 (3.3)21.3 (0.8)
172.2 (6.8)
82.1 (3.2)
Unit: mm (inch)
■Fuse replacement
One fuse is installed in the supplied DC power cable. If the
fuse blows or the device stops functioning, track down the
source of the problem, repair it, and replace the damaged
fuse with a new one of the proper rating.
Fuse rating: 250 V 5 A
Fuse Coding explanation
Fuse Coding: F 250 V 5 A
Fuse Voltage Rating: 250 Volts
Fuse Current Rating: 5 Amperes
■Recommendation
CLEAN THE DEVICE THOROUGHLY WITH FRESH WATER
after exposure to saltwater, and dry it before using. Otherwise, the
device’s keys may become unusable, due to salt crystallization.
NOTE: If the device’s waterproof protection appears defective,
carefully clean it with a soft, damp (fresh water) cloth, then dry it
before operating.
The device may lose its waterproof protection if the case is
cracked or broken, or the device has been dropped.
Contact your Icom distributor or your dealer for advice.
Table of contents
Popular Network Hardware manuals by other brands
Texas Instruments
Texas Instruments DRV8308 user guide
Digi
Digi One SP quick start guide
Quick Eagle Networks
Quick Eagle Networks Solo T1 DSU Specification sheet
ZyXEL Communications
ZyXEL Communications Prestige 2602HW Series user guide
ATTO Technology
ATTO Technology FibreBridge 2100R Software manual
Mitel
Mitel 3300 Configuration notes