lease Note ( for 1 and 2 relay devices ONLY):
As a power saving feature, the display dims if settings are not being made.
Even though the device seems to operate correctly, the relay(s) will not energise if the input voltage is below the operating
voltage.
12 Month guarantee:
Ourproductis guaranteed for a 12 (twelve) month period fromdateofpurchase. This guarantee is valid for defects arisingfrom
failureduringspecifiedconditions. This guarantee does not cover damage duetoabuse,tampering or improper installation. Our
company does not accept liability for any consequential damage or loss arising from product malfunction. Should this product
provetobe defective, kindly return for inspection or repair.
elay specifications:
ontactrating: 10A 250 VAC 2500VA
echanicallife: 30million operations
lectrical life: 250000operations(atmaximumload)
For furtherinformation, please visitus at: www.iconelectronics.co.za
Menu operation (single display):
All adjustments are made via the three front mounted buttons.
Press the “MENU” button repeatedly until the desired setting is reached, press “SELECT” to display the current value of the
selectedparameter,or sub menu (if applicable).
The“+”and“-”buttonsareusedtochange the value.
“ENTER”willreturnthedeviceto the menu.
The “BACK” button will exit the menu.
Menu operation (dual display):
Press the menu “4” button repeatedly until the desired setting is reached.
The“S”and“T” buttons are usedtochange the value.
“4” will display the next menu item.
To exit the menu hold “4” button for 3 seconds.
Menu options:
Exitthemenubeforemakingthefollowingadjustments.
Lock / unlock parameters:
(default: unlocked)
Press “BACK” (“T”), then “ENTER” (“4”) and hold the 2 buttons until the desired option is displayed.
Thedisplaycyclesbetween“Loc”(nochangesallowed)&“u.Loc”(parametersmaybeadjusted)
Full / reduced menu (default: Full)
Press “SELECT”(“S”), then “ENTER”(“4”) and hold the 2 buttons until the desired option is displayed.
The display cycles between “rEdu” (limited menu) & “Full” (all parameters are accessible)
Access Code: (default: no code)
Oncetheaboveoptionshavebeensetasrequired,Press “BACK” and “SELECT” (“T”and “S”) simultaneously until “CODE” is
displayed.
Now use the “+” & “-” (“S” and “T”) to enter a code.
Once a code is entered, access to the options above is not permitted.
To clear the code, re-enter the same code again.
If the code is forgotten. Press and hold “+” & “-” (“S”and “T” ) until “CODE” is displayed while re-applying power to the device.
· The output 4-20mAis dependant on the value being displayed, and is set up in a similar manner to the display.The offset
parameter determines when 4mA is output, and the span is the amount required for the output to increase by an additional
12mAie. 20mAis output when the value displayed = re-transmit OFFSET+SPAN
· To set the re-transmittion signal to follow the input signal (the output 4-20mAfollows the 4-20mAreceived), set the re-tx offset
and span settings to the same value as the display offset and span settings.
· To set the re-transmittion signal to invert the input signal (the output = 4mAwhen the input = 20mA), set the re-tx offset = (display
offset+span)andre-txspan = (display span x -1).
· Whenever the input signal is above or below the “CAL.O” or “CAL.S” values by more than 3%.The display indicates “Er.Hi” or
“ER.Lo”.
· Certain settings are reset to default when the device is re-configured. Re-check all settings to ensure they are correct before
commissioning.(usethe advanced menu)
