ICP DAS USA A-823PGH Series User manual

- 1 -
Language English
Version V1.1
Update Nov.2008
………………………………………………
What’s on your package?
 One A-823 series card
 One companion ISA C (V2.1 or later)
 One Quick Start Guide(This document)
………………………………………………
Installing Windows Driver
Follow those steps:
1. Setup the Windows driver. You can get the driver from:
C :\NAP OS\ISA\A823\ LL\
http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/a823/dll/
1
2
A
-
82
PGH/PGL
Windows driver only support windows 98/NT/2000 and
XP/2003/vista 32-bit versions.

- 2 -
2. Click button to start installation.
3. Click button to install driver into the default folder.
4. Click button to continue installation.
5. Select “NO, I will restart my computer later” and then click
button.
………………………………………………
I/O Base Address & Interrupt Setting
 The base address is set from SW1 DIP switch on
board:
 The Interrupt Level Setting
3
ON
1 2 3 4 5 6
A9 A8 A7 A6 A5 A4`
BASE ADD
R
A9 A8 A7 A6 A5 A4
200-20F OFF ON ON ON ON ON
210-21F OFF ON ON ON ON OFF
220-22F() OFF ON ON ON OFF ON
230-23F OFF ON ON ON OFF OFF
: : : : : : :
300-30F OFF OFF ON ON ON ON
3F0-3FF OFF OFF OFF OFF OFF OFF
SW1 : BASE ADDRESS
(

) : default base address is 0x220
IRQ 3 4 5 6 7 9 10 11 12 14 15 NC
Int rrupt 15
(d fault)

- 3 -
………………………………………………
Installing Hardware on PC
Follow those steps:
1. Shut down and power off your computer
2. Remove all covers from the computer
3. Select an empty ISA slot
4. Carefully insert your I/O card into the ISA slot
5. Replace the PC covers
6. Power on the computer
After powering-on the computer, continue next process.
………………………………………………
Adding Hardware
7. Add Hardware
7-1 Open the “Control Panel” by click the item “Start / Settings /
Control Panel”.
7-2 ouble-click the item “Add/Remove Hardware” and Click
the “Next >” button.
7-3 Select the item “Add/Troubleshoot a device” and click the
“
““
“Next >” button.
7-4 Select the item “Add a new device” and click the “Next >”
button.
4
5
Adding hardware is used on Windows 2000/XP/2003/Vista
32 only. Windows 9X/Me/NT users can skip it.

- 4 -
7-5 Select the item “No, I want to select the hardware from a
list” and click the “Next >” button.
7-6 Select the item “Other device” and click the “Next >” button.
7-7 Click the “Have Disk…” button.
7-8 Click the “Browse…” button to select the Inf file default path
is C:\ AQPRO\A823_Win2K\Inf and click the “OK” button.
7-9 Select the correct device from the “Models:” listbox and Click
the “Next >” button.
7-10 The windows show to dialog box and Click the “OK” button to
enter the device’s properties settings.
8. Modify the device properties
9. Reboot the PC
The detail “add hardware” information. Please refer to:
CD:\NAPDOS\ISA\Manual\PCI_ISA_PnP_Driver_Installation_in_Win9x_2K_XP.pdf
2
.
Click “Change Setting” to
change I/O Range ( epend on I/O
Base Address)
1
.
Select Input/Output Range
. Select Interrupt Request
No devices are conflicting
No devices are conflicting
4
.
Click “Change Setting” to
change Interrupt Request.
( epend on Interrupt Level setting)

- 5 -
………………………………………………
Pin Assignments
 CN1,CN2 igital Input/Output Connector .
 CN3 Analog Input/Output/Timer/Counter Connector.
The detail pin assignments information. Please refer to :
CD:\NAPDOS\ISA/A82 /Manual/82 .pdf
http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/a823/manual/823.pdf
6
CN1 igital Input CN2 igital Output

- 6 -
………………………………………………
Self-Test
1. Use CA-2002(Optional) to connect the CN1 with
CN2.
2. Run the A-823 sample program.
Get the file from( efault ):
C:\ AQPro\A823_WINxx\ EMO
7
CN1
CN2
CN

- 7 -
3. Check number of the A-823, and test IO function.
4. Get IO function test result.
3
.
Click this
button to do
IO test.
2.
Select the board
number for the A-823.
It starts from 0.
1
.
The o
ne
A
-
823
had successfully
installed to
PC
.
4
.
Click the channel
0 、2、4、6 in the O.
5
.
I show to channel
0、2、4、6 for high state.
(Red light)
Complete

- 8 -
………………………………………………
Additional Information
 A-82 Series Card Product page:
http://www.icpdas.com/products/ AQ/pc_based/a-823.htm
 CA-2002(Optional) page:
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
 Documents:
C :\NAP OS\ISA\A823\manual
http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/a823/manual/
 Software:
C :\NAP OS\ISA\A823
http://www.icpdas.com/download/isa/a823/index.htm
The ICP DAS Web Site
http://www.icpdas.com
Contact Us
[email protected]
Copyright ©2008 by ICP AS Co., Ltd. All right are reserved
8
 Technical support
 Supplies and ordering information
 Ways to enhance your device
 FAQ
 Application story