ICP DAS USA M-7046 User manual

ICP DAS CO., LTD.
Copyright © 2016 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
M
-
70
4
6
(
D
)
Quick St
art
1
Quick Start F o r M-7 0 4 6 ( D )
June 2016, Version 1.00
Congratulations on purchasing the M-7046(D) the most popular automation solution for
remote monitoring and control applications. This Quick Start Guide will provide
information needed to get started with the M-7046(D). Please also consult the User
Manual for detailed information on the setup and use of the M-7046(D).
In addition to this guide, the shipping box includes the following items:
7000 Series User Manual
http://www.icpdas.com/download/7000/manual.htm
I-7000 Website
http://www.icpdas.com/root/product/solutions/remote_io/rs-485/i-7000_m-7000/m-704
6.html
ICP DAS Website
http://www.icpdas.com
M-7046(D)
Plastic Rail DVD Quick Start Guide

ICP DAS CO., LTD.
Copyright © 2016 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
M
-
70
4
6
(
D
)
Quick St
art
2
1
----------------------------------------------------------------------------------
Understanding the Hardware Specifications
and Wiring Diagrams
Before installing the hardware, you should have a basic understanding of hardware
specification and the wiring diagrams.
I/O Specifications Pin Assignment
Wire Connection

ICP DAS CO., LTD.
Copyright © 2016 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
M
-
70
4
6
(
D
)
Quick St
art
3
Make sure the INIT* wire to (B)GND.
3
-----------------------------------------------------------------
-----
------------
Connecting to the PC and the Power Supply
M-7046(D) series modules are equipped with an
RS-485 port that can be used to connect to an
RS-232/USB converter to connect the module to a host
PC
2
--------------------------------------------
Booting the M-7046(D) in
Init Mode
Connect to the PC
using an RS-232 Converter
Connect to the PC
using a USB Converter




          

 

  

 

  

 





  

          

  

 

  



  

 





  


ICP DAS CO., LTD.
Copyright © 2016 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
M
-
70
4
6
(
D
)
Quick St
art
4
4
---------------------------------------------------------------------------------
Download the DCON Utility Pro
The DCON Utility Pro is an easy-to-use tool designed to enable simple configuration
of I/O modules that use the DCON protocol Pro.
Step 1: Locate the DCON Utility
The DCON Utility Pro can be obtained from the companion from the
ICPDAS site:
http://www.icpdas.com/download/7000/7000.htm
5
----------------------------------------------------------------------------------
Using the DCON Utility Pro to Initialize the
M-7046(D) Module
The M-7046(D) is an I/O module based on the DCON protocol, meaning that you can
use the DCON Utility Pro to easily initialize it.
Step 1: Run the DCON Utility Pro
Double-click the DCON Utility
shortcut on your desktop.

ICP DAS CO., LTD.
Copyright © 2016 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
M
-
70
4
6
(
D
)
Quick St
art
5
Step 2: Use the COM1 port to communicate with the M-7046(D)
Click the “COM Port” option from the menu and a dialog box will be displayed that will
allow you to set the communication parameters as described in the table below.
Step 3: Search for the M-7046(D) module
Click “Start Search” button from the toolbox to search for the M-7046(D) module.
After the M-7046(D) module was display in the list, click “Stop Search” button.
Communication
parameter
Factory
default Value
Address 00
Baud Rate 9600
Protocol DCON
Checksum Disabled
Parity N,8,1
Start Search
Stop Search

ICP DAS CO., LTD.
Copyright © 2016 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
M
-
70
4
6
(
D
)
Quick St
art
6
Step 4: Connect to the M-7046(D)
After clicking on the name of the module in the list, a dialog box would be display.
Step 5: Initialize the M-7046(D) module
Set the “Address” field in the dialog box to 1 and then click “Setting” button to save the
settings.
Make sure the INIT* and (B)GND
connection has been disconnected
6
--------------------------------------------
Rebooting the M-7046(D)
Module in Normal Mode

ICP DAS CO., LTD.
Copyright © 2016 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
M
-
70
4
6
(
D
)
Quick St
art
7
7
----------------------------------------------------------------------------------
Starting the Module Operation
After rebooting the M-7046(D) module, search for the module to make sure the
settings have been changed. You can double click on the name of the module in the
list to open the configuration dialog box.
 Modbus Table
  DCON Pro Protocol
For more details regarding the DCON protocol, please check the enclosed CD at:
CD path: \\napdos\7000\manual\
Or from our web site at: ftp://ftp.icpdas.com/pub/cd/8000cd/napdos/7000/manual/
Address
Description
R/W
00001 ~ 00004 DO Value R/W
00033 ~ 00036
10001 ~ 10004 DI Value R
00065 ~ 00068 DI Latch High Value R
00069 ~ 00072 DO Latch High Value R
00097 ~ 00100 DI Latch Low Value R
00101 ~ 00104 DO Latch Low Value R
00264 Write 1 to clear latch values (FC 05) W
00513 ~ 00516 Write 1 to clear DI counter (FC 05, FC15) W
30001 ~ 30004
40001 ~ 40004 DI Counter Value R
Function
Command
Response
Notes
Reads the name of the module $AAM !AA(Data) AA: module address
Reads the firmware version of the module $AAF !AA(Data)
Reads the status of the digital output channels @AA (Data)
Sets the digital output channels @AA(Data) 0~F
Reads the digital input counter of channel N #AAN !AA(Data) N: The channel to be read
Clears the digital input counter of channel N $AACN !AA
Reads the status of the latched DO channels $AALS !(Data) S: 0 is low, 1 is high
Clears the status of the latched DO channels $AAC !AA