ICP DAS USA IR-712-MTCP User manual

P1
IR-712-MTCP(-5) Quick Start
v1.6, Jun 2020
Packing List
In addition to this guide, the package includes the following items:
IR-712-MTCP
CA-IR-SH2251 * 2
CA-IR-SH2251-5 * 2
Technical Support
[e-mail]
www.icpdas.com
Resources
How to search for drivers, manuals and
spec information on ICP DAS website.
For Mobile Web
For Desktop Web
(IR-712-MTCP)
(IR-712-MTCP-5)
Model Name
Model Name

P2
1. Check operation mode
Push DIP switch to the position of normal operation mode (OP).
2. Connect to PC by Ethernet

P3
3. Plug in an IR Emitter Cable
Plug the IR emitter cable CA-IR-SH2251(-5) into the 3.5 mm jack of the
IR Output 1.
4. Power Wire Connection
Connect the power supply cable (+10 ~ +30 VDC) to the power
connector.
5. Install IR Utility
Please get the IR Utility installation file (IR_Util_Setup_v#_#_#_#.zip)
from the web page of the product.
+10 ~ 30 VDC
GND

P4
6. Search and Connect to the Module
Launch the IR utility and follow the 5 steps below.
(1) Select the IR-712-MTCP in the “Module” combobox.
(2) Click the “Search Modules” button.
(3) Click OK button after selecting the “Network Interface” to the
IR-712-MTCP.
(4) Mouse double clicking the row of the searched IR-712-MTCP.
(5) Enter the main window of the IR-712-MTCP utility when
communication connected.
(2)
(4)
(3)
(5)
(1)

P5
7. Set Device and IR Command Quantity
Please click the “Set Device & IR Command Quantity” button to open the
setup window. Three steps to go:
Step 1: Set device quantity.
(1) Set the Device Quantity to be 1.
(2) Press the “Set” button.
(3) Press the Next (right arrow) button.
3
2
1

P6
Step 2: Configure the IR device names and its IR command
quantity.
(1) Enter Device Name and IR Command Quantity.
(2) Press the “Set” button.
(3) Press the Next (right arrow) button.
Step 3: Set each IR command name
Type the IR command name and “Enter” or click “Set” button. The prefix
number (e.g. 1_Play) is the number of an IR command stored in the IR
module. Click “OK” button after setting..
1
2
3
3
4
2
1

P7
8. Learn IR Commands
In the section “Test and Save Learned IR Commands” of the IR utility:
(1) Select the item in “Device Name” and “Command Name” combobox.
(2) Click “Learn On” button to enable IR learning mode (TR/LN LED is
ON).
(3) Aim the emitter head of the remote control (RC) to the “IR Input” hole
on the module (distance less than 3 cm) and press the remote control
button which is to be learned in a short time. After IR learning is
finished, the TR/LN LED is OFF.
(4) Select IR Output 1 in the output channel combobox.
(5) Aim the IR emitter, which is plugged in IR Output 1 jack, to the IR
receiver of the controlled device. Click “Run Command” button to
check the effectiveness of the IR learning command. Repeat (2) and
(3) if no action on the device.
(6) Click “Save this Cmd” button.
(7) Repeat the above (1)~(6) to finish IR learning.
Besides, the color rectangle (marked a blue dotted frame) means:
➢Red: Learning data is saved in the item of “Command Name”.
➢Yellow: Get learning data form IR module. The data is buffered and
lost when selecting other item of “Command Name”.
➢White: No learning data saved in the current item of “Command
Name”.
2
4
6
5
1
距離：≤3 cm
遙控器
2
3

P8
9. Download IR Commands to the module
After IR learning finishes, click Menu [Download]-> [Download IR
Commands to IR-712-MTCP].
10. Test IR Commands
Go to the “Test IR Commands in IR-712-MTCP” section:
(1) Select IR Command No.
(2) Select Output Channel to 1. Aim the IR emitter head to the appliance.
(3) Press “Transmit (MBTCP)” button. The appliance reacts means
success.
1
2
3