ICP DAS USA ZT-2053 User manual

ICPDAS,ZT‐2000DIOSERIESQuickStart,Version1.2.1Page1
Copyright©2013byICPDASCo.,Ltd.AllRightsReserved.
ZT‐2000DIOSERIES
QuickStart
1 What’sintheShippingPackage?
The shipping package contains the following items:


2
PreparingtheDevice
1. Refer the chapter 3. to configure the DIP switch of ZT-2000 I/O device.
2. Install the ZT Configuration Utility to configure the ZT-2000 coordinator.
CD: \Napdos\ZigBee\ZT_Series\Utility
http://ftp.icpdas.com/pub/cd/usbcd/napdos/zigbee/zt_series/utility
3. Power Supply: +10 ~ +30 VDC

ANT‐124‐05QuickStart
ZT‐2000DIODevice
+Vs GND +Vs
GND
If any of these items are missing or damaged, please contact your local distributor
for more information. Save the shipping materials and cartons in case you need to
ship the module in the future.

ICPDAS,ZT‐2000DIOSERIESQuickStart,Version1.2.1Page2
Copyright©2013byICPDASCo.,Ltd.AllRightsReserved.
3 SettinguptheZT‐2000DIODevice
3.1 IntroductiontotheConfigurationParameters
A. “Pan ID” parameter is the group identity for a ZigBee network, and must
the same for all devices in the same ZigBee network.
“Address/Node ID” parameter is the individed identity of a specific the
ZigBee module, and must be unique for each device connected the same
ZigBee network.
B. “RF Channel” parameter indicates the radio frequency channel, and must
be set to the same value as other modules on the same ZigBee network.
Channel 0x00 0x01 …… 0x0F
Frequency(MHz) 2405 2410 …… 2480
※ RF channels 0x04, 0x09, 0x0E or 0x0F are recommended because they do
not overlap with the Wi-Fi frequencies based.
C. Protocol/Application Mode：
When implementing custom programs based on different protocols, the
following application modes are recommended in order to ensure
communicatible
User Program Protocol ZT-2000 I/O ZT-2550 ZT-2570
DCON DCON Transparent Transparent
Modbus RTU Modbus RTU Transparent
Modbus Gateway
Transparent
Modbus Gateway
Modbus TCP Modbus RTU ------ Modbus Gateway
000102030405060708090A0B0C0D0E0F
802.11b/g
Channel1
802.11b/g
Channel6
802.11b/g
Channel11
802.11b/gChannel(NorthAmerica)
802.15.4Channel
2400
MHz
2485
MHz

ICPDAS,ZT‐2000DIOSERIESQuickStart,Version1.2.1Page3
Copyright©2013byICPDASCo.,Ltd.AllRightsReserved.
4 RotationSwitchandDIPSwitch
The configuration of ZT-2000 series can be adjusted by using the external
rotary switch and the DIP switches. The ZT-2000 device should only be rebooted
once the configuration is complete.
DIPSwitchtotheZT‐2042/ZT‐2043/ZT‐2053/ZT‐2055
DIPSwitchtotheZT‐2052/ZT‐2060
12345678910 11 12
Address LSB
(
Node ID
)
Address MSB
(
Node ID
)
Protocol
Checksum
Pan ID
ON
RF Channel Reserved
Address LSB
(
Node ID
)
Address MSB (Node ID)
Protocol
Checksum
Pan ID
RF Channel

ICPDAS,ZT‐2000DIOSERIESQuickStart,Version1.2.1Page4
Copyright©2013byICPDASCo.,Ltd.AllRightsReserved.
RotationSwitch
0 1 2 3 …… F Note
Address SW 01 02 03
…… 0F
Node ID SW 0x0001 0x0002 0x003 …… 0x000F MSB = 0
0 1 2 3 …… F
Address 10 11 12 13
…… 1F
Node ID 0x0010 0x0011 0x0012 0x013 …… 0x001F MSB = 1
※ Once the address of hardware switch is set to 0x00, it mens the address is using
software configurations. Refer the more detailed information at Sec. 6.6 of user
manual.

DIPSwitch
Number Item Status Explain
OFF Valid Address (Node ID) from 0x00 to 0x0F
1 Address MSB
ON Valid Address (Node ID) from 0x10 to 0x1F
OFF DCON Protocol
2 Protocol
ON Modbus RTUProtocol
OFF Disabled
3 Checksum
ON Enabled
OFF Pan ID = 0x0000
4 ZigBee Pan ID ON Pan ID = 0x0001
OFF ------
5 ON 0x08
OFF ------
6 ON 0x04
OFF ------
7 ON 0x02
OFF ------
8
ZigBee
RF Channel
ON 0x01

ICPDAS,ZT‐2000DIOSERIESQuickStart,Version1.2.1Page5
Copyright©2013byICPDASCo.,Ltd.AllRightsReserved.
5 Start‐upZT‐2000I/ODevice
As the ZigBee network is controlled by the ZigBee coordinator, the
ZT-2550/ZT-2570 (ZigBee coordinator) must be configured first. Please refert to
documents shown below for full details of how to configure these devices.
Once configuration of the ZigBee coordinator has been completed. Set
the ”Pan ID” and the “RF Channel” values for the ZT-2000 I/O device to the same
values as the network, and then reboot the device. The module will
automatically start to function on the ZigBee network using the default protocol.
※ Documents
http://ftp.icpdas.com.tw/pub/cd/usbcd/napdos/zigbee/zt_series/document/zt-255x/
http://ftp.icpdas.com.tw/pub/cd/usbcd/napdos/zigbee/zt_series/document/zt-257x/
※ Configuration Utility (Used to configure ZT-2000 I/O device Coordinator)
http://ftp.icpdas.com.tw/pub/cd/usbcd/napdos/zigbee/zt_series/utility/

ICPDAS,ZT‐2000DIOSERIESQuickStart,Version1.2.1Page6
Copyright©2013byICPDASCo.,Ltd.AllRightsReserved.
6 Examples
ConfigurationsofZT‐2550/ZT‐2570


ConfigurationsofZT-2000 I/O Device
12345678910 11 12
12345678 ON

Number Item Status Explain
1 Address MSB OFF Address/Node ID is 01(Rotation Switch=1)
2 Protocol ON Use Modbus RTU Protocol
3 Checksum OFF Disabled
4 ZigBee Pan ID OFF Pan ID=0x0000
5 ON 0x08
6 ON 0x04
7 ON 0x02
8
ZigBee
RF Channel
OFF ------
ZigBee RF Channel = 0x0E


7 CommunicationTest
Once the ZT-2000 I/O device has joined the ZigBee network, the signal
quality can be comfirmed by monitoring the status of the ZigBee Net LED
indicators. If the LED indicator shows a steady light, communication with the
ZT-2000 I/O device has been successfully established for data acquisition and
control.
ICP DAS also provides the “DCON Utility”, which can be used to simulate
DCON/Modbus communication. This software can also be used to verify the
device settings and ZigBee I/O functions.
※ The DCON Utility can be dowmload from:
http://ftp.icpdas.com/pub/cd/8000cd/napdos/driver/dcon_utility/
mulate I/O channel operating via using DCON Utility Si
1. Launch DCON Utility and select the correct COM Port settings to connect the
ZigBee Coordinator (ZT-2550/ZT-2570).
2. Clicking “Search” button will start searching which ZT-2000 I/O device is in the
same ZigBee network.
3. If there is any ZT-2000 I/O devices displayed, double clicking the “module
name” will start the I/O channels operated platform.
1
3
2
4
ICPDAS,ZT‐2000DIOSERIESQuickStart,Version1.2.1Page7
Copyright©2013byICPDASCo.,Ltd.AllRightsReserved.

ICPDAS,ZT‐2000DIOSERIESQuickStart,Version1.2.1Page8
Copyright©2013byICPDASCo.,Ltd.AllRightsReserved.
8 Troubleshooting
(1) Technical Support.
If you have any difficulties using your ZT-2000 series I/O device, please
send a description of the problem to [email protected]
Include the following items in your email:
A description or diagram of the current DIP switch positions.
A copy of the configuration file for the ZT-2000 coordinator. This file can be
obtained using the procedure outlined below and should be attached to your
email.
a. Set the DIP switch of the ZT-255x device to the [ZBSET] position then
reboot the device. Launch the ZT Configuration Utility and select [Save Log]
icon to save the configuration of the ZT-255x as a file.
b. After clicking the [Save Log] icon, enter the “File Name” and the “File Path”
in the Windows “Save” dialog box. Once the configuration has been
successfully saved, the following message will be displayed.
(2) LED Indicator Status：
LED Indicator Status Introduction
ZigBee Router (Slave)
Steady Lit The Signal is Strong
Blinking (500 ms) The Signal is Available
Blinking (1s) The Signal is Weak
Blinking (2s) The Signal is Unstable or There is no Available
The status of module board
Steady Lit The Power is ON and the Module Initialization is
Correct
Blinking (200ms) Module Initialization Failure
Blinking (1s)
Watchdog is Enabled and the status of the I/O channel
has been changed to the Safe Value. Reset the module
via the power switch or configuration commands.
ZigBee PWR
(Red LED)
Steady Unlit The Power is OFF
The status of DI/DO channels
Steady Lit The DI/DO channel is Enabled
ZigBee DI/DO
Steady Unlit The DI/DO channel is Disabled