ICT INDUSTRIAL Series User manual

THEPOWEROFRELIABILITY
855-002-025
ICT INDUSTRIAL SERIES
HAZARDOUS LOCATIONS
INSTRUCTION MANUAL
SPECIFICATIONS
Input
Voltage
Range
Output
Voltage
Output
Current
(Cont.)
Current
Limiting
Line
Regulation
Load
Regulation
Output
Ripple
(Max)
Efficiency
(Typical)
Over-
voltage
Protection
Fuse
20-30 VDC 13.8 VDC
+/- 300 mV
10.0 Amps 10.5 Amps
+/- 5%
0.50% 0.40% 40 mV RMS 16.0 VDC 86% 10 Amp
20-30 VDC 13.8 VDC
+/- 300 mV
14.0 Amps 20.5 Amps
+/- 5%
0.45% 0.30% 40 mV RMS 16.0 VDC 88% 20 Amp
ICT2412-10AH (1)(2)(3)
ICT2412-15AH (1)(2)
20-30 VDC 13.8 VDC
+/- 300 mV
12.0 Amps 16.0 Amps
+/- 5%
0.45% 0.30% 40 mV RMS 16.0 VDC 88% 15 Amp
ICT2412-12AH (1)(2)
(1) CSA C22.2 No 107.1, UL 1012 Approved
(2) CSA C22.2 No 213, UL 1604 Approved
(3) Remote ON/OFF Control Version
NOTE: These converters can be mounted on a standard 19" Rackmount.
Please contact us for more information.
20-30 VDC 13.8 VDC
+/- 300 mV
20.0 Amps 31.0 Amps
+/- 5%
0.45% 0.30% 40 mV RMS 16.0 VDC 95% 35 Amp
ICT2412-20AH (1)(2)(3)
20-30 VDC 13.8 VDC
+/- 300 mV
28.0 Amps 42.0 Amps
+/- 5%
0.45% 0.30% 40 mV RMS 16.0 VDC 95% 35 Amp
ICT2412-30AH (1)(2)
ICT4812-10AH (1)(2)
ICT4812-15AH (1)(2)
20-60 VDC 13.8 VDC
+/- 200 mV
10.0 Amps 10.5 Amps
+/- 5%
0.70% 0.60% 20 mV RMS 18.5 VDC 85% 10 Amp
20-60 VDC 13.8 VDC
+/- 200 mV
15.0 Amps 20.5 Amps
+/- 5%
0.70% 0.70% 25 mV RMS 18.5 VDC 85% 20 Amp
Industrial Power
Series
GND
GND
Input +
Output +
GND
GND
Input
Output
From Batteries
To Load
CONNECTIONS
4 Terminal Type, No Remote Control 5 Terminal Type, With Remote ON/OFF Control
Industrial Power Series
GND
GND
Input +
Output +
GND
GND
Input
Output
FromBatteries
To Load
REMOTE

THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I,
DIVISION 2, GROUPS A, B, C & D OR
NON-HAZARDOUS LOCATIONS ONLY.
EXPLOSION HAZARD: Substitution of components
may impair suitability for class 1 division 2.
EXPLOSION HAZARD: Do not disconnect equipment
unless power has been switched off or the area is
known to be non-hazardous.
EXPLOSION HAZARD: Do not replace fuse unless
power has been switched off or the area is known to
be non-hazardous.
RISQUE D'EXPLOSION: La substitution de
composants peut rendre ce materiel inacceptable pour
les emplacements de classe 1 division 2.
RISQUE D'EXPLOSION: Couper le courant ou
s'assurer que l'emplacement est designe non
dangereux avant de replacer le fuse.
RISQUE D'EXPLOSION: Avant de deconnecter
l'equipement, couper le courant ou s'assurer que
l'emplacement est designe non dangereux.
WARNING
4
4
4
4
4
4
4
THEPOWEROFRELIABILITY
ICT INDUSTRIAL SERIES
SETUP
The ICT Industrial Power Series - Hazardous Locations
converters are non-isolated DC to DC converters
approved for use in hazardous Class 1 Div 2 locations,
such as oil fields, chemical and refinery plants. They
are designed for use on negative ground systems.
Each converter is designed for high efficiency and long
service life. The rugged case and modular design have
proven durable in harsh environments. Extra silicone is
used for vibration and moisture resistance. Standard
features include: current limiting, overvoltage
protection, fuse protection, high surge capacity, easy
access mounting holes, and a terminal block
connector.
These instructions should be read before using the
product and saved for future reference.
Mount converter securely.
Do not apply power until unit is completely wired.
For best results, wire converter directly to battery
using heavy gauge wire with in line fuse.
NOTE: Do not wire output directly to a power
source. Paralleling outputs are not recommended.
Please contact technical support for application
assistance.
4
4
4
4
Check fuse inside unit, if blown, replace with same
type and rating fuse.
Check for proper voltage at input while converter
is under load.
Ensure the Remote ON/OFF pin is connected
to the V+ input on 5 terminal models.
TROUBLESHOOTING
4
4
4
LIMITED WARRANTY
ICT Ltd. warrants to the original consumer purchaser that this
product shall be in good working order, free from defects in
materials and workmanship, for a period of one (1) year from the
date of purchase. Should failure occur during the above stated time
period, then ICT will, at its option, repair or replace this product at
no additional charge except as set forth below. All parts, whether
for repair or replacement, will be furnished on an exchange basis.
All exchange pieces become the property of ICT. This limited
warranty shall not apply if the ICT product has been damaged by
unreasonable use, accident, negligence, disaster, service, or
modification by anyone other than the ICT factory.
Limited warranty service is obtained by delivering the product
during the above stated one (1) year warranty period to an
authorized ICT dealer or ICT factory and providing proof of purchase
date. If this product is delivered by mail, you will insure the product
or assume risk of loss or damage in transit, and prepay shipping
charges to the factory.
Every reasonable effort has been made to ensure that ICT product
manuals and promotional materials accurately describe ICT product
specifications and capabilities at the time of publication. However,
because of ongoing improvements and updating of ICT products,
ICT cannot guarantee the accuracy of printed materials after the
date of publication and disclaims liability for changes, errors or
omissions.
If this ICT product is not in good working order, as outlined in the
above warranty, your sole remedy shall be repair or replacement as
provided above. In no event will ICT be liable for any damages
resulting from the use of or the inability to use the ICT product,
even if an ICT employee or an authorized ICT dealer has been
advised of the possibility of such damages, or for any claim by any
other party.
ICT reserves the right to make changes without further notice to
any products or documentation for improvement of reliability,
function, or design.
ICT Ltd. does not recommend use of its products in life support
applications wherein a failure or malfunction of the product may
directly or indirectly threaten life or cause injury. The user of ICT
products, which are to be used in life support applications as
described above, assumes all risks of such use and indemnifies ICT
against all damages.