Ideal Life Gluco-Manager GMM0001 User manual

IDEAL LIFE Gluco-Manager
TM
Blood Glucose Management System
Model GMM00010001
Products may vary from images shown
*NOTE: The IDEAL LIFE Gluco-Manager™ is intended for use in the quantitative measurement of glucose in fresh capillary
whole blood from the nger and the following alternative sites: the palm, the forearm, the upper-arm,the calf and the thigh. It is
intended for use by adults with diabetes mellitus in a non-clinical environment such as in the home, as an aid to monitoring the
effectiveness of a diabetes control program. It is not intended for the diagnosis of, or screening for, diabetes mellitus and not in-
tended for use on neonates. The alternative site testing can be used only during steady state blood glucose conditions. The system
is intended for information purposes only, for expert advice make sure to consult a healthcare professional. Any instructions for
change in treatment and health related information or advice should only be made directly with a healthcare professional.
Version 7.0 Jun 2013
INSTRUCTION MANUAL
Read before use
May be used with IDEAL LIFE Pod™
(sold separately) for use with IDEAL LIFE
Health Management System™

2IDEAL LIFE Gluco-Manager™
Table of Contents
Table of Contents......................................2
Introduction.................................................3
Preface..........................................................3
Contraindications......................................3
Precautions..................................................4
Important Information..............................4
About Alternative Site Testing (AST)....6
Package Contents......................................7
Additional Items ........................................8
IDEAL LIFE Pod™Location/
Interference................................................ 9
Before You Start Your IDEAL LIFE
Gluco-Manager™....................................10
Your IDEAL LIFE Pod™..........................11
Test Strip Description ............................12
Important Test Strip Information..........12
Powering Up Your IDEAL LIFE
Gluco-Manager............................................13
First Time Power Up and Activation
When Using a Pod..................................14
About Control Solution........................15
Important Control Solution Test
Information...............................................15
How to do a Control Solution Test.....16
Functions...................................................18
Table of Contents
Taking Your Blood Glucose
Reading.....................................................19
Getting a drop of blood ......................19
When obtaining blood from sites
other than the ngertip.........................19
Taking a reading......................................20
Looking at Previously Taken
Readings...................................................21
Looking at Messages..............................22
Looking at Graphics...............................23
Comparing Meter and Laboratory
Results......................................................24
Care and Maintenance..........................25
Cleaning and Desinfecting....................26
A List of the Signs of Potential
Deterioration..........................................27
Specications...........................................28
Limitations of Use..................................29
Problem Solving Guide..........................30
Error Message.........................................31
Summary of Operation.........................32
FCC Statement ......................................33
Customer Information..........................34
Service Requirements............................35

3
Instruction Manual
Introduction
Preface
Thank you for purchasing the IDEAL LIFE Gluco-Manager™, or GMM 0001 and IDEAL LIFE Pod™, or
ILP 0001.This completely automatic system measures your blood glucose, captures subjective information
and manages information automatically so that you can better manage your blood glucose with your care
provider. Your measurement reading is clearly displayed on a large screen on the IDEAL LIFE Gluco-
Manager™ after each measurement, and later stored for a more detailed analysis in the form of tables for
easy viewing and graphs for easy interpretation.Your new IDEAL LIFE Gluco-Manager™ provides you with
accurate, whole blood test results for blood glucose.The system is compact with convenient operation so it
is simple to use.
Intended Use
IDEAL LIFE Gluco-Manager™ GMM 0001 Blood Glucose Monitoring System is indicated for the
quantitative measurement of glucose in fresh capillary whole blood taken from the ngertip and alternative
sites for self-testing by persons with diabetes in the home, or by healthcare professionals in healthcare
facilities.
Testing is done outside the body (in vitro diagnostic use).The IDEAL LIFE Gluco-Manager™ is not intended
for the diagnosis of, or screening for, diabetes mellitus and not intended for use on neonates.
The alternative site testing (the palm, forearm, upper arm, calf and thigh) using this system can be used only
during steady-state blood glucose conditions.
You do not need to calibrate your meter, making it easier for the user to monitor blood glucose at home.
The IDEAL LIFE Gluco-Manager™ can wirelessly communicate to a communication gateway or an access
point.
CAUTION: Before using any product to test your blood glucose, read all instructions thoroughly
and practice the test. Do all quality control checks as directed and consult with a diabetes healthcare
professional. For proper interpretation of blood glucose measurements, make sure to consult a physician.
Contraindications
**Warning: This system is designed for use outside the human body. It is not recommended for use on
infants and is not intended for and should not be used to try and measure the blood glucose of infants as it
may not be accurate and/or relied upon.
Do NOT use the device for purposes other than measuring blood glucose.This unit does not serve as a
cure of any symptoms or disease.The data measured are only for reference. Always consult your physician
to have the results interpreted.
Introduction

4IDEAL LIFE Gluco-Manager™
Precautions
• Do not drop this unit. Please avoid strong impact. Disassembly or modication of the unit may
lead to permanent reading error.
• The device might not meet its performance specications if stored or used beyond the specied
temperature and humidity ranges.
• Operating conditions: 50°F to 104°F (10°C to 40°C), below 80% RH.
• System storage: 39.2°F to 86°F (4°C to 30°C), below 80% RH.
• Be sure to keep this manual for future reference.
• NOTE: Before using any product to test your blood sugar (blood glucose), read all instructions
and practice the test. Do all quality control checks as directed and consult with a diabetes
healthcare professional.
• Do not place the device in liquid, nor put it where it could fall into liquid.
• Close supervision is necessary when the device is used by, on, or near children, handicapped people or
invalids.
• Do not use the device come into contact with surfaces which are too hot to touch.
• Do not use the device where aerosol sprays are being used.
• Do not use the device if it is not working properly, or if it has been damaged.
Precautions

5
Instruction Manual
Important Information
• Severe dehydration and excessive water loss may cause false low results. If you believe you are
suffering from severe dehydration, consult a healthcare professional immediately.
• Test results below 60 mg/dL (3.3 mmol/L) indicate hypoglycemia, or low glucose. Test results higher than
240 mg/dL (13.3 mmol/L) indicate hyperglycemia, or high glucose. Consult your physician when one of
these results is shown repetitively.
• If you are experiencing symptoms that are not consistent with your blood glucose test results and you
have followed all instructions described in this owner’s manual, call your healthcare professional.
• Inaccurate results may occur in severely hypotensive individuals or patients in shock. Inaccurate low
results may occur for individuals experiencing a hyperglycemic-hyperosmolar state, with or without
ketosis. Critically ill patients should not be tested with blood glucose meters.
• Please refer to your test strip package insert for additional important information.
• Always follow the operation procedures described in the manual in order to obtain correct results.
The meter and lancing device are for single individual use. Do not share them with anyone including other
family members! Do not use on multiple individuals!
All parts of the kit are considered biohazardous and can potentially transmit infectious diseases, even after
you have performed cleaning and disinfection.
You should refer to the following linkages for more information:
“FDA Public Health Notication: Use of Fingerstick Devices on More than One Person Poses Risk for
Transmitting Bloodborne Pathogens: Initial Communication” (2010)
http://www.fda.gov/MedicalDevices/Safety/AlertsandNotices/ucm224025.htm
“CDC Clinical Reminder: Use of Fingerstick Devices on More than One Person Poses Risk for Transmitting
Bloodborne Pathogens” (2010) http://www.cdc.gov/injectionsafety/Fingerstick-DevicesBGM.html
For any questions or comments, please call an IDEAL LIFE customer representative at
1-866-IDEAL-41 (866-433-2541)
Important Information

6IDEAL LIFE Gluco-Manager™
About Alternative Site Testing (AST)
IMPORTANT: There are limitations for doing alternative site testing (AST).Please consult your
healthcare professional before you do AST.
What is AST?
Alternative site testing (AST) means that people use parts of the body other than ngertips to check
their blood glucose levels.This system provides you to test on your forearm, upper arm, calf, or thigh
with the equivalent results to ngertip testing when used at appropriate times.
What is the advantage?
Fingertips feel pain more readily because they are full of
nerve endings (receptors).At other body sites, since nerve
endings weren’t so condensed, you won’t feel as much
pain as at the ngertip.
When to use AST?
Food, medication, illness, stress and exercise can affect a
blood glucose levels. Capillary blood at ngertip reects
these changes faster than capillary blood at other sites.
Therefore when testing blood glucose during or
immediately after meal, physical exercise, or any other
event, take blood sample from your nger only.
We strongly recommend you do AST in the following
intervals:
• In a pre-meal or fasting state (more than 2 hours since the
last meal).
• 2 hours or more after taking insulin.
• 2 hours or more after exercise.
Do NOT use AST if:
• You think your blood glucose is low.
• You are unaware of hypoglycemia.
• Your AST results do not match the way you feel.
• You are testing for hyperglycemia.
• Your routine glucose results are often uctuating.
• You are pregnant.
About Alternative Site Testing (AST)

7
Instruction Manual
How to increase the accuracy?
Stimulating blood perfusion by rubbing the puncture site prior to blood extraction has a signicant
inuence on the glucose value obtained. Blood from the site without rubbing exhibits a measurably
different glucose concentration than blood from the nger. When the puncture site was rubbed prior
to blood extraction, the difference was signicantly reduced.
Please follow the suggestions below before getting a drop of blood:
• Rub the puncture site about 20 seconds before penetration.
• Use a clear cap (included in the kit) instead while setting the lancing device.
Package Contents
The IDEAL LIFE Gluco-Manager™ GMM0001 Blood Glucose Monitoring System consists of three main
products: a blood glucose meter, test strips, and control solution.These products have been designed,
tested and proven to work together as a system to produce accurate blood glucose test results. Use
only the same brand-name test strips and control solution with the IDEAL LIFE Gluco-Manager™.
YOUR SYSTEM INCLUDES:
Package Contents Package Contents
CARRYING BAG
INSTRUCTION MANUAL
2 “AAA”
BATTERIES FOR
YOUR IDEAL
LIFE GLUCOMANAGER™
GMM0001 IDEAL LIFE
GLUCO-MANAGER™
QUICK
INSTALLATION
GUIDE

8IDEAL LIFE Gluco-Manager™
Additional Items (*sold separately)
There are 3 levels for control solutions. Please call 1-866-IDEAL-41 (866-433-2541) for availability.
Additional Items
ILP 0001 IDEAL LIFE POD™
25 STERILE
LANCETS
25 TEST STRIPS
CONTROL
SOLUTION
1 CLEAR CAP LANCING
DEVICE
NOTE: Check your system to be sure that it is unopened prior to use and that it contains all parts listed
above. If either of these conditions occurred, please return your system to the place of purchase.
AC ADAPTER

9
Instruction Manual
Location/Interference
The IDEAL LIFE Manager™ may be used with a communication gateway such as the IDEAL LIFE Pod™ or
access point such as a cellular phone or computing device.
The IDEAL LIFE Pod™ uses wireless radio waves to transfer information from your IDEAL LIFE Manager™.
For the best distance and least interference, the recommended IDEAL LIFE Pod™location is:
NOTE:
While using an IDEAL LIFE Pod™ with telephone line connectivity, the telephone line will be in use. If the
telephone line is in use while trying to use your IDEAL LIFE Pod™, the information will be stored in your
IDEAL LIFE Manager™ and will be sent later.
• Away from electrical appliances such as a
TV, personal computer or a cordless phone
• In a HIGH and CENTRAL
location with no obstructions
such as walls
Location/Interference

10 IDEAL LIFE Gluco-Manager™
Before You Start
Before You Start
Your IDEAL LIFE Gluco-ManagerTM
Test Port
LCD Display
Blue LED
Left “Soft”Button
START/ESCAPE Button
Right “Soft”Button
Battery Cover
Battery Cover
AAA Batteries

11
Instruction Manual
Your IDEAL LIFE PODTM
* Note: There is only a battery compartment for telephone line connectivity
LED Display
AC Adapter Jack
USB Port
Ethernet Cable RJ45 Jack Connection
Battery Cover
Telephone Cord RJ11 Jack For Telephone Connection
Your IDEAL LIFE Pod
™
(*An optional accessory sold separately)
(Sealed with an antenna for cellular Internet connectivity)
Telephone Connection Telephone Cord RJ11 Jack For Line Connection
(sealed for cellular internet connectivity)

12 IDEAL LIFE Gluco-Manager™
Test Strip Description
Test Strip Description
• Your system measures the amount of sugar (glucose) in whole blood. Blood is applied to the absorbent
hole of the test strip and is automatically drawn into the reaction cell where the reaction takes place.
• The test strip consists of the following parts:
Contact Bars
Insert this end of the test strip into the meter.
Push it in rmly until it will go no further
Test Strip Handle
Hold this part to insert the test strip into the slot.
Conrmation Window
This is where you conrm if enough blood has been
applied to the Absorbent Hole of the strip.
Absorbent Hole
Apply a drop of blood here; the blood will
be sucked automatically.
• Refer to the section below: “Taking Your Blood Glucose Reading,” for complete instructions.
Important Test Strip Information
• Store test strip packages in a cool, dry place from 39.2°F to 86°F (4°C to 30°C) . Keep away
from direct sunlight and heat. Do not freeze.
• Store your test strips in their original vial only; do not transfer them to a new bottle or anyother
container.
• After removing a test strip from the vial, immediately replace the vial cap and close it tightly.
• With clean, dry hands, you may touch the test strip anywhere on its surface when removing it from
the vial or inserting it into the meter.
• Use each test strip immediately after removing it from the vial.
• Write the discard date on the vial label when you rst open it. Discard remaining test strips and
the vial 90 days after rst opening date.
• Apply only blood sample or control solution to the absorbent hole. Applying other substances to
the absorbent hole will cause inaccurate results.
• Do not use test strips beyond the expiration date printed on the package since they may cause
inaccurate results.
• Do not bend, cut or alter a test strip in any way.
(Model:AGS-1112)

13
Instruction Manual
Powering UpYour IDEAL LIFE Gluco-Manager™
INSTALLING THE BATTERIES (INCLUDED)
• Remove the battery compartment door on your IDEAL LIFE Gluco-Manager™ by lifting the battery
door using the notch.
• Place the batteries as instructed on the device.
• Replace the battery compartment door and click into place.
• NOTE: Replacing the battery does not affect previous test results stored in memory of the meter.
However, the time and date settings may need to be updated if batteries are not in the device for an
extended period of time.
Use only new batteries of the required size and the recommended
Installation type. For best performance and the longest life, alkaline batteries are recommended.
Do not mix different type, date or brand name batteries together. Be sure to follow the instructions when
installing the batteries. Since batteries can leak chemicals that damages electronic parts, leaving the battery
in the housing for a long period without using the device may damage the main unit.
Please remove the batteries if you are not going to use the device for an extended period of time
(i.e., 3 months or more).The batteries should be kept away from small children as they pose a choking
hazard. If swallowed, promptly see a doctor for help.
• Environment Protection – Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local Authority or retailer for recycling advice.
Powering UpYour IDEAL LIFE Gluco-Manager™

14 IDEAL LIFE Gluco-Manager™
First Time Power Up And Activation When Using An IDEAL LIFE POD™
First Time Power Up And Activation When
Using An IDEAL LIFE POD™(*an optional accessory, sold separately)
To use the IDEAL LIFE Gluco-Manager™with your IDEAL LIFE Pod™you must call an IDEAL LIFE
customer representative to activate. Make sure to call IDEAL LIFE before you begin.Then make sure
that the IDEAL LIFE Pod™ is connected to a telephone line cord and RJ11 jack (or an Ethernet cord
and RJ45 jack), “Powered ON”!
Hold down any button on your IDEAL LIFE Gluco-Manager™
for 3 seconds to Power up.
READ THROUGH THE IDEAL LIFE INC.TERMS AND
CONDITIONS FIRST, THEN PROCEED AND FOLLOW
THE PROMPTS ON THE SCREEN AS SHOWN HERE:
First select the appropriate language using the buttons
labeled and OK.
Then Answer the question on the following screen regarding
terms and conditions using the YES and NO labeled buttons.
To gain full advantage of all the features your IDEAL LIFE Gluco-Manager™ has to offer, using an IDEAL
LIFE Pod™is recommended. To ensure that your IDEAL LIFE Gluco-Manager™ and IDEAL LIFE Pod™
are setup properly you will need to call IDEAL LIFE directly to activate your system. You should ensure
that the steps are followed correctly, you should rst setup your IDEAL LIFE Pod™, power it up, and then
begin the steps of powering up your IDEAL LIFE Gluco-Manager™. During your activation call with IDEAL
LIFE, an IDEAL LIFE customer representative will verify your IDEAL LIFE Gluco-Manager™and IDEAL LIFE
Pod™ID numbers and you will be ready to take full advantage of all your IDEAL LIFE Gluco-Manager™ has
to offer. For a detailed description of all the features and functions continue to the FUNCTIONS section
of this manual.

15
Instruction Manual
About Control Solution (sold separately)
Control solutions contain a known amount of glucose that reacts with test strips. By comparing your
control solution test results with the expected range printed on the test strip vial label, it is able to check
that the meter and the test strips are working together as a system and that you are performing the test
correctly. It is very important that you do this simple check routinely to make sure you get accurate results.
How often should the control solution test be performed?
• When you use this system to test your blood for the rst time, practice the procedure using
control solution. When you can do three tests in a row that are within the expected range, you are
ready to test your blood.
• Routinely check the meter and test strips, so perform a single test for each level of control solution at
least once a week
When should the control solution test be performed?
• When you rst get your IDEAL LIFE Gluco-Manager™.
• When you begin using a new vial of test strips.
• Whenever you suspect that the meter or test strips are not working properly.
• When your blood glucose test results are not consistent with how you feel, or when you think your
results are inaccurate.
• When your test strips are exposed to extreme environmental conditions (See “Important Test Strip
Information” below).
• When you want to practice running the test.
• If you drop the meter.
Important Control Solution Test Information
• Use the same branded control solutions as the test strips.
• Check the expiry date on the control solution vial. Do not use if expired.
• Control solution, meter, and test strips should come to room temperature (20°C to 25°C/ 68°F to 77°F)
before testing.
• Shake the vial before use. Discard the rst drop of control solution. After squeezing, wipe off the
dispenser tip to avoid contamination. The above tips ensure you get a good sample and an accurate result.
• Use a period of 90 days from the date that you rst open it. Record the discard date (date opened plus 90
days) on the control solution vial. Discard after 90 days.
• Store the control solution tightly closed at temperature from 36°F to 86°F (2 to 30°C) and do not freeze.
NOTE! The control solution range printed on the test strip vial is for appropriately branded
control solution only. It is used to test meter and test strip performance. It is not the
recommended range for your blood glucose level.
About Control Solution

16 IDEAL LIFE Gluco-Manager™
How To Do A Control Solution Test?
Step 1. Power up Device
From the off position, press the power button to turn on the display. From the default screen, press
the power button once more.The display will instruct you to insert a strip at this time. Insert a test
strip with contact bars end rst and facing up into the test slot. (Contact bars must be inserted all
the way into the meter or you may get an inaccurate test result.)
After the “ ” symbol appears on the display, you may now move to the STEP 2 and add the control
solution to the test strip. If you decide not to perform a control solution test, press Soft Button
labeled EXIT to return to the default screen.
Step 2. Apply Control Solution
Shake the control solution vial well. Remove the cap from the control solution bottle. Place cap on at
surface. Squeeze the vial, discard the rst drop, and wipe off the dispenser tip to prevent contamination.
Squeeze the vial again to get another drop and apply the drop to the top of cap.
How To Do A Control Solution Test?

17
Instruction Manual
How To Do A Control Solution Test?
CAUTION!To avoid contaminating the control solution with the content of the test strip, you
have to place a drop of control solution on a clean surface or on your nger tip rst. Do not
directly apply control solution into a strip.
Step 3. Display test result
Compare the result with the range printed on the test strip vial.
The result should fall within this range.
Out of Range Results
If test results fall outside the range printed on the test strip vial, check the “Problem Solving Guide,” below
and repeat the test. If you continue to get out of range results, it means that the system may not be work-
ing properly. Do NOT test your blood. Contact an IDEAL LIFE customer representative at 1-866-IDEAL-41
(866-433-2541) to resolve the issue.

18 IDEAL LIFE Gluco-Manager™
Functions
(when using the IDEAL LIFE POD™, an optional accessory sold separately)
Main Screen
The Main Screen is your default screen.This is where you will be
directed to after completing functions and where you will nd status
indicators for the functioning of your IDEAL LIFE Gluco-Manager™.
In the upper middle portion of the display you will nd a battery icon,
displaying power status of your IDEAL LIFE Gluco-Manager™
Indicates full power
Indicates power is getting low, you should change your batteries
Indicates that your blood pressure measuring function has been turned off.
Replace your batteries immediately.
If you have unread messages, you will see an envelope icon on the upper left corner of the
display.
Functions

19
Instruction Manual
Taking Your Blood Glucose Reading
Be sure to read this section and any inserts found in the test strip box carefully before taking a
reading. Wash and dry your hands before starting.
Getting a Drop of Blood
Step 1. Use your lancing device (sold separately) to
obtain a blood sample. Follow the instructions included
in your lancing device.
WARNING! To reduce the chance of infection:
• Never share a lancet or the lancing device with anyone.
• Always use a new, sterile lancet. Lancets are for single use only.
• Avoid getting hand lotion, oils, or debris in or on the lancets
and the lancing device.
WHEN OBTAINING BLOOD FROM SITES OTHER THAN THE FINGERTIP
A clear cap, often provided, makes it easier to get a drop of blood from AST.
Step 2.Wash your hands and the Puncture Site
Select the puncture site either in nger or in other parts (AST). Clean the puncture site with 70% using
cotton moistened with 70% alcohol and let it air-dry.
Step 3. Spuncturevure Site
• Fingertip
Hold the lancing device rmly against the side of your nger.
• Sites other than a ngertip
Please refer to the section of “About Alternative Site Testing” above. Please consult your health
professional before obtaining blood from sites other than a ngertip.
WARNING! The system requires a very small blood drop to perform a test. You can obtain it
from a ngertip. Choose a different spot each time you test. Repeated punctures in the same
spot may cause soreness and calluses. Before you decide to do palm testing, please consult
your health professional rst.
Step 4. Gently Massage the Area. Do NOT Smear the Blood Sample
To obtain correct results, it is recommended that the rst drop of blood
should be discarded with a clean tissue paper or cotton. Use the second
drop of blood for testing.The required blood sample is 0.7 microlitre in a
volume.
WARNING! The rst drop of blood usually contains
tissue uid and serum, which may affect the test
result. It should be discarded.
Taking Your Blood Glucose Reading

20 IDEAL LIFE Gluco-Manager™
Taking a Reading
Step 1. Insert the Test Strip
Insert a test strip with contact bars end rst and facing up into the test
slot. (Contact bars must be inserted all the way into the meter or you may
get an inaccurate test result.) The meter turns on automatically and shows
the following messages:
Step 2. Apply Sample
Obtain a drop of blood using the adjustable lancing device. The blood a
sample must be at least 0.7 microliter in volume or you may get an
inaccurate test result. When “ ” appears on the display, apply the blood
to the absorbent hole of the test strip where it meets the narrow channel.
Do not push your nger against the test strip or try to apply a smeared
sample. The blood should completely ll the conrmation window
before the meter begins to count down. If not, do not try to add more
blood to the test strip. Discard the test strip and retest with a new one.
If you have trouble lling the test strip, please contact the dealer for
assistance.
Step 3. Display a Glucose Result
Your blood glucose test result will appear.After the reading is displayed
you may remove the test strip. Discard the used test strip carefully to
avoid contamination.
When the measurement is complete, your IDEAL LIFE Gluco-Manager™
will then display your reading automatically and begin to communicate
when you are using a communication gateway or access point such as a
cellular phone, computing device or the IDEAL LIFE Pod™.
When the measurement is complete, your IDEAL LIFE Gluco-Manager™
will then display your reading automatically and begin to communicate
when you are using a communication gateway or access point such as a
cellular phone, computing device or the IDEAL LIFE Pod™.
Connection times may vary depending on many factors. Your reading will
always be stored in your meter memory for local lookup. After displaying
your reading and automatically communicating the information, your meter
will automatically return to the default screen before going to sleep mode.
Each time your IDEAL LIFE Gluco-Manager™communicates successfully
to IDEAL LIFE through your IDEAL LIFE Pod™ the time and date are set
to ensure reliable date and time stamping of all readings.
NOTE! If you do not apply a blood sample within 2 minutes, the
meter will automatically turn off. You must remove the test strip
and insert it back again to restart the test procedure.
Taking a Reading