IDS NXT rio User manual

IDS NXT
IDS Imaging Development Systems GmbH
Dimbacher Str. 6-8
D-74182 Obersulm, Germany
T: [phone]
E: [e-mail]
W: http://www.ids-nxt.com
Setup IDS NXT rio

2021-04-13 2
IDS NXT: Setup IDS NXT rio
Contents
1 Preface .............................................................................................................................................. 4
2 Symbols and hints ............................................................................................................................ 5
3 Safety instructions ............................................................................................................................ 6
4 Standards and directives .................................................................................................................. 8
5 IDS NXT rio ....................................................................................................................................... 9
5.1 Ambient conditions ...................................................................................................................... 9
5.2 Connecting a IDS NXTrio .......................................................................................................... 10
6 Electrial specifications ..................................................................................................................... 11
6.1 Pin assignment GigE connector (RJ45) ....................................................................................... 11
6.2 Pin assignment I/Oconnector ..................................................................................................... 11
7 Status LED ...................................................................................................................................... 13
8 Setup in network ............................................................................................................................. 14
8.1 Installing IDS NXTcockpit .......................................................................................................... 14
8.2 Getting an IP address ................................................................................................................. 14
8.3 Starting IDS NXTcockpit ............................................................................................................ 14
8.4 Logging on to the device ............................................................................................................. 16
8.5 Changing the IP address ............................................................................................................ 17
8.6 Network configuration in IDS NXT cockpit .................................................................................... 18
9 Opening device website .................................................................................................................. 19
10 HTTPS communication with SSL certificate ................................................................................... 20
10.1 Creating SSL package with existing certificates .......................................................................... 20
10.2 Uploading certificate to camera ................................................................................................. 22
10.3 Optional: disable HTTP ............................................................................................................. 22
11 Updating IDS NXT OS .................................................................................................................... 23
11.1 Updating per IDS NXTcockpit ................................................................................................... 23
11.2 IP address with DHCP .............................................................................................................. 24
11.3 IP address without DHCP ......................................................................................................... 24
12 Troubleshooting/FAQ .................................................................................................................... 25
12.1 Booting the camera in service mode .......................................................................................... 26
12.2 Resetting the camera to factory settings ..................................................................................... 26
12.3 Booting the camera in runtime mode .......................................................................................... 27

2021-04-13 3
IDS NXT: Setup IDS NXT rio
Index .................................................................................................................................................. 29

2021-04-13 4
IDS NXT: Setup IDS NXT rio
1 Preface
Introduction
IDS Imaging Development Systems GmbH has taken every possible care in preparing this manual. We
however assume no liability for the content, completeness or quality of the information contained therein. The
content of this manual is regularly updated and adapted to reflect the current status of the software. We
furthermore do not guarantee that this product will function without errors, even if the stated specifications are
adhered to.
Under no circumstances can we guarantee that a particular objective can be achieved with the purchase of
this product.
Insofar as permitted under statutory regulations, we assume no liability for direct damage, indirect damage or
damages suffered by third parties resulting from the purchase of this product. In no event shall any liability
exceed the purchase price of the product.
Please note that the content of this manual is neither part of any previous or existing agreement, promise,
representation or legal relationship, nor an alteration or amendment thereof. All obligations of IDS Imaging
Development Systems GmbHresult from the respective contract of sale, which also includes the complete and
exclusively applicable warranty regulations. These contractual warranty regulations are neither extended nor
limited by the information contained in this manual. Should you require further information on this product, or
encounter specific problems that are not discussed in sufficient detail in the manual, please contact your local
dealer or systeminstaller.
Trademarks
The IDS logo is a registered trademark of IDS Imaging Development Systems GmbH,
registered for U.S. (Reg.No. 4,513,138) and other countries.
IDS NXT and uEye are registered trademarks of IDS Imaging Development Systems
GmbH. Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation. All other
products or company names mentioned in this manual are used solely for purposes of identification or
description and may be trademarks or registered trademarks of the respective owners.
Copyright
© IDS Imaging Development Systems GmbH. All rights reserved. This manual may not be reproduced,
transmitted or translated to another language, either as a whole or in parts, without the prior written permission
of IDS Imaging Development Systems GmbH.
Status: April 2021
Contact
Visit our web site http://www.ids-nxt.com where you will find all the latest information about our software and
hardware products. Please contact your local IDS distributors for first level support in your language. For a list
of IDS distributors worldwide please go to our website http://www.ids-nxt.com.
Address
IDS Imaging Development Systems GmbH
Dimbacher Str. 6-8
D-74182 Obersulm, Germany
T
[phone]
E
[e-mail]
W
http://www.ids-nxt.com

2021-04-13 5
IDS NXT: Setup IDS NXT rio
2 Symbols and hints
This symbol indicates hints with useful information for better understanding and using
features and functions.
This symbol indicates important warnings for product safety to prevent damage.
This symbol indicates important warnings for personal safety to prevent injury.

2021-04-13 6
IDS NXT: Setup IDS NXT rio
3 Safetyinstructions
Read carefully these safety instructions before installing and using the product. The producer is not
responsible for damages and injury, which can occur due to false handling of the product and ignoring the
safety instructions. All warranty will be spoiled in this case.
Intended use
IDS industrial cameras are to be used to capture images for visualization and image processing tasks. They
are designed for use in industrial environments. Observe the requirements for the proper use of this product.
Failure to do so will render the warranty void.
· The product is not authorized for use in security relevant applications. If it is used in security relevant
applications, the customer is responsible for the necessary approvals.
· If the product is modified or changed, all approval becomes invalid. In this case, the customer is responsible
for ensuring product conformity.
· The warranty expires if the product is improperly disassembled, reworked or repaired by the customer or a
third party and IDS Imaging Development Systems GmbHassumes no liability for defects. If you need
service, please contact the support team.
· The product is not a toy. Operate and store out of the reach of children.
Protection against electrostatic discharge (ESD)
Board-level cameras are especially sensitive to electrostatic discharge. Make sure to avoid mechanical or
electrical damage of the printed circuit board or its connections. Wear ESD-protective clothing and observe
the rules for handling ESD-sensitive components.
· Do not touch the printed circuit board while it is powered.
· Always hold the board by the edges to avoid the risk of electrostatic discharge damage.
· For optimum ESD behavior, a clearance of 4 mm from non-shielded housings must be maintained all the
way around. For shielded housings, a smaller clearance is possible.
· Attach the board to a conductive surface using the fixing screws. If this is not possible, ensure an insulating
connection.
· Use connecting cable with a low-resistance shield on both sides.
Installation, operation and maintenance
The product must be connected, taken into operation and maintained only by appropriately qualified
personnel. The error-free and safe operation of this product can only be ensured if it is properly transported,
stored, set up and assembled, and operated and maintained with due care. The installation, inspection,
maintenance, extension, and repair may only be done by authorized personnel.
· Observe the specifications in the documentation when installing the product.
· Do not subject the product to direct sunlight, moisture or shock. Ensure that the IP code of the product
meets the requirements for the ambient conditions.
· Only operate the product under ambient conditions for which the respective product is approved. The use
under other ambient conditions may result in damage.
· To avoid any damage to the connectors, only mount or remove the product with the cables disconnected.
· Lay cables in such a way that no one is endangered.
· Before starting up, check if the electrical wiring corresponds to the specifications in the documentation.
Faulty wiring (overvoltage, undervoltage) can result in a damage in the electronics.
Transport
· Only use ESD packaging for storage and transport of ESD-sensitive components.

2021-04-13 7
IDS NXT: Setup IDS NXT rio
· Keep packing materials like films away from children. Abuse may result in suffocation.
Operation and power supply
The camera power supply must meet the requirements for SELV (safety extra low voltage)/LPS (limited power
source) or ES1/PS2.
WARNING! Non-approved power supplies for camera operation may cause painful or dangerous electric
shock. Serious injury or death may occur. Use a power supply that meet the requirements for SELV (safety
extra low voltage)/LPS (limited power source) or ES1/PS2.
· In order to ensure electrical safety, we recommend using a shielded connection cable or grounding the
camera housing so that the camera housing is connected to ground via the appropriate installation.
Avis pour le Canada
Fonctionnement et alimentation électrique
L'alimentation électrique de la caméra doit être conforme aux exigences de sécurité SELV (très basse
tension de sécurité)/LPS (source à puissance limitée) ou ES1/PS2.
AVERTISSEMENT ! Avec un bloc d'alimentation non prévu pour les caméras, il existe des risques de
décharges électriques douloureuses ou dangereuses. Celles-ci peuvent provoquer des blessures graves,
voire mortelles. Utilisez un bloc d'alimentation conforme aux exigences de sécurité SELV (très basse
tension de sécurité)/LPS (source à puissance limitée) ou ES1/PS2.
· Pour garantir la sécurité électrique, nous recommandons l'utilisation d'un câble de connexion blindé ou la
mise à la terre du boîtier de la caméra, afin que ce dernier soit relié correctement à la masse.
CAUTION! As the camera housing may get hot depending on the operating conditions there may be risk of
burns. Provide sufficient heat dissipation so that the housing temperature does not exceed 55 °C (131 °F).
NOTICE! Cameras with Power-over-Ethernet (PoE) can be powered from an external source or via PoE. The
camera should not be supplied with both power sources at the same time, as this may cause irreparable
damage to the camera.
Correct disposal
Dispose the camera and accessories properly and separately from other types of waste to encourage
recycling of reusable materials and to protect the environment.
According to the EC Directive 2012/19/EU (WEEE) we are obliged to take back this product, distributed by us
after August 13, 2005, free of charge at the end of its useful life and to ensure it correct disposal. As this
product is exclusively for commercial use (B2B), it must not be handed over to a public disposal facility. The
product can be disposed of by specifying the date of purchase and the serial number at the following address:
IDS Imaging Development Systems GmbH
Dimbacher Str. 6-8
D-74182 Obersulm, Germany

2021-04-13 8
IDS NXT: Setup IDS NXT rio
4 Standards and directives
(only valid for devices with housing)
IDS Imaging Development Systems GmbHhereby confirms that this product has been developed, designed
and manufactured in compliance with the following European directives
· 2014/30/EU: EMC - Electromagnetic compatibility
· 2011/65/EU: RoHS - Restriction of the use of certain hazardous substances in electrical and electronic
equipment
· Regulation (EC) No. 1907/2006 concerning the Registration, Evaluation, Authorization and Restriction of
Chemicals (REACH)
· The CE declaration of conformity is available on the IDS website.
If the product is modified or changed all approval becomes invalid. In this case the customer is responsible for
ensuring product conformity.
Product type
IDS NXT rio
Information for CE
EMC specifications
EN 61000-6-2
EN 55035
EN 61000-6-4*
EN 55032 (Class A)
Information for USA
This equipment has been tested and found to comply
with part 15 of the FCC Rules
Class A
Information for Canada
Renseignements pour le Canada
CAN ICES-3 (A)/NMB-3(A)
Information for UL
UL 62368-1
CAN/CSA C22.2 No. 62368-1-14
Further information
RCM
KC (R-R-img-NXTrio)
* Cameras are intended exclusively for use in industrial environments.
This product may cause interference when used in residential areas. Such use is to be avoided unless the user takes
measures to prevent interference emissions.
For customers in the USA
For a class A digital device:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
Name of Responsible Party
IDS Imaging Development Systems, Inc.
92 Montvale Ave., Ste 2800
Stoneham, MA 02180
U.S.A.
T: [phone]

2021-04-13 9
IDS NXT: Setup IDS NXT rio
5 IDS NXT rio
Housing/board-level
+/-
Dimensions height xwidth x length
34 x44 x73 mm
Mechanical specifications
Mechanical specifications
IP code
IP 30
· Schutz gegen das Eindringen kleiner Fremdkörper
· Kein Wasserschutz
Ambient conditions
Ambient conditions
Lens mount
C-mount, see Optical specifications
Mounting holes bottom/top/side/front
4/0/0/0
Thread diameter
M3
Status LED
Status LED
Interface connector
GigE RJ45, screwable
Power supply
Input I/O connector (M12): 12-24 V DC +20 %, max. 1 A
Input GigE connector (RJ45): PoE 41-57 V DC, max. 350 mA
I/O connector
12-pin M12 connector, screwable
Electrical specifications
Electrical specifications
5.1 Ambient conditions
The temperature values given below refer to the outer device temperature of the camera housing. The
temperature inside of the camera housing is generally higher than the outer temperature and may be up to
70 °C (158 °F).
Device temperature during operation
0 °C … 55 °C
32 °F … 131 °F
Device temperature during storage
-20 °C … 60 °C
-4 °F … 140 °F
Humidity
20 % … 80 %, relative, non-condensing
Non-condensing means that the relative air humidity must be below100 %. Otherwise, moisture will form on
the camera surface. If, for example, air has a relative humidity of 40 % at 35 °C (95 °F), the relative humidity
will increase to over 100 % if the air cools down to 19.5 °C (67 °F); condensation begins to form.
CAUTION! As the camera housing may get hot depending on the operating conditions there
may be risk of burns. Provide sufficient heat dissipation so that the housing temperature does
not exceed 55 °C (131 °F).
Notes on ambient conditions
· Avoid high air humidity levels and rapid temperature changes when using IDS cameras.
· Temperatures below+4 °C (39 °F) combined with excessive relative air humidity levels can cause icing.
Provide sufficient heat dissipation so that the specified device temperature is not exceeded during operation.
In general, the following recommendations apply:
· For a passive heat dissipation, mount the camera on a thermally-conductive surface like a metal plate or a
heat sink.
· If necessary, provide an active cooling for example by means of a fan.
With increasing device temperatures, the image quality could be reduced due to thermal noise. It is
recommended to mount the camera to a heat-dissipating unit even if the camera is operated belowthe
maximum specified temperature.

2021-04-13 10
IDS NXT: Setup IDS NXT rio
Vibration and shock resistance
Vibration and shock resistance of the cameras corresponds to EN60068-2-6 and EN 60068-2-27.
5.2 Connecting a IDS NXT rio
Fig. 1: IDS NXT rio
· 1: Pin assigmnet GigE connector (RJ45, 8-pin)
· 2: Pin assignment I/O connector (M12, 12-pin)
NOTICE! The camera can be supplied with voltage both from an external source and via
Power-over-Ethernet (PoE). The camera should not be supplied through both voltage sources
at once as this can irreparably damage the camera.
Check the power supply to the camera. Connect the camera to to a Gigabit Ethernet port on the PC either
directly or using switches. Please read the following notes before setting up.
Cabling
· The data network and the camera network should be cabled separately. Therefore, it is recommend
connecting the cameras by a separate network card.
· It is recommend to use Cat5e type cables.
· The cable length of the individual segments must not exceed 100 m. A segment is a continuous cable
connection between two network devices (e.g. PC, camera, switch).
· It is recommended to cable the network throughout at 1000 Mbit/s.
Network card
· To ensure optimum performance of the network connection, you need to install the latest drivers for your
network card.
· GigE network adapters for PCI slots are limited in its transfer rate to approximately 80-90 MByte/s.
· It is recommended to set the "Receive Descriptors" in the network card settings to the maximum value.
· It is recommended to set the "Jumbo Frames" (also: Jumbo Packet) in the network card settings to the
maximum value.
Note that the connection between the camera and the PC must continuously be able to transport jumbo
packets to ensure the transmission of the jumbo packets. Information on these settings is provided in the
manual supplied with the network adapter.

2021-04-13 11
IDS NXT: Setup IDS NXT rio
6 Electrial specifications
· Pin assignment GigE connector (RJ45)
· Pin assignment I/O connector
6.1 Pin assignment GigE connector (RJ45)
8-pin RJ45 socket
Pin
Designation 100BASE-TX
Designation 1000BASE-T
Fig. 2: RJ45
socket, camera
rear view
1
Tx+
Bl_DA+
2
Tx-
Bl_DA-
3
Rx+
Bl_DB+
4
Bl_DC+
5
Bl_DC-
6
Rx-
Bl_DB-
7
Bl_DD+
8
Bl_DD-
The RJ45 socket of the IDS NXTrio complies with the IEC 60603-7 standard.
6.2 Pin assignment I/O connector
12-pin M12 connector (Attend 216A-12MSR)
Pin
Signal
Description
Fig. 3: I/O connector,
camera rear view
1
VBUS
Power supply: 12-24 V DC +20 %
2
VBUS GND
Reference level (ground) for power supply and RS-232
3
Opto IN (0)
Trigger input with optocoupler
4
Opto IN (1)
Input 1 with optocoupler
5
Opto IN (COM)
Reference level for all Opto IN
6
Opto OUT (COM)
Reference level for all Opto OUT
7
Opto OUT (1)
Output 1 with optocoupler
8
Opto OUT (2)
Output 2 with optocoupler
9
RS232 (RxD)
Serial interface
10
RS232 (TxD)
Serial interface
11
Opto IN (2)
Input 2 with optocoupler
12
Opto OUT (0)
Flash output with optocoupler
Shield
Shield
Shield
You can check the color assignment of the cable on the Website directly at the specific accessory item.
The maximum length of the I/O cable is 30 m. The cable must be shielded.

2021-04-13 12
IDS NXT: Setup IDS NXT rio
Power supply
NOTICE! The camera can be supplied with voltage both from an external source and via
Power-over-Ethernet (PoE). The camera should not be supplied through both voltage sources
at once as this can irreparably damage the camera.
Voltage
Input I/O connector (M12): 12-24 V DC +20 %
Input GigE connector (RJ45): PoE 41-57 V DC
Current
Input I/O connector (M12): min. 1 A
Input GigE connector (RJ45): min. 350 mA
Residual ripple
120 mVpp
IDS Imaging Development Systems GmbH recommends to adjust the power supply to the power requirement
of the camera to limit overheating in case of short circuit.
To ensure the electrical safety, the camera power supply must meet the requirements for SELV (safety extra
low voltage) / LPS (limited power source) or ES1 / PS2. The camera power supply must be rated by the values
given in the table above. It also must ensure that the voltage values given in the table above are available at the
input of the camera.
Avis pour le Canada:
IDS ImagingDevelopment Systems GmbH recommande d'adapter l'alimentation électrique aux besoins de
la caméra afin de limiter la surchauffe en cas de court-circuit.
Pour garantir la sécurité électrique, l'alimentation de la caméra doit être conforme aux exigences de
sécurité SELV (très basse tension de sécurité)/LPS (source à puissance limitée) ou ES1/PS2.
L'alimentation de la caméra doit respecter les valeurs indiquées dans le tableau ci-dessus. Elle doit
également répondre au fait que les tensions indiquées dans le tableau ci-dessus sont présentes à l'entrée
de la caméra.
Information on the power consumption of individual camera models can be found in the model data sheet.
Keep in mind that a voltage drop will occur when you use long cables for power supply to the
camera. Choose the size of the cable in such a way that the supply voltage available at the
input of the camera is at least 12 V.
To supply the IDS NXTrio camera with power using PoE or PoE+, you can use PoE
injectors or switches that are compatible with IEEE standard 802.3af or IEEE standard
802.at.

2021-04-13 13
IDS NXT: Setup IDS NXT rio
7 Status LED
Fig. 4: Status LEDs
The camera has two LEDs that indicate information of the current status.
· LED 1: camera status (two-color)
· LED 2: Network status (two-color)
LED 1
Camera is off/no power
Camera is booting
Camera is ready
Camera is open
Camera is ready - no valid IP address
No firmware loaded
Service firmware active
LED 2
No network connection
Network connection OK
Network connection OK + data transfer
Continuous data transfer
Network error

2021-04-13 14
IDS NXT: Setup IDS NXT rio
8 Setup in network
The following steps must be executed to setup IDS NXTrio camera:
1. Install the IDS NXT cockpit.
2. Connect the camera to the network and power supply.
NOTICE! The camera can be supplied with voltage both from an external source and via
Power-over-Ethernet (PoE). The camera should not be supplied through both voltage sources
at once as this can irreparably damage the camera.
8.1 Installing IDS NXT cockpit
The installation package of the IDS NXTcockpit is available for download from https://en.ids-
imaging.com/downloads.html.
IDS NXTcockpit is currently available for Windows 64-bit. You should have an up-to-date
graphics card driver installed for an optimal display.
8.2 Getting an IP address
During the initial network setup, the following situations can occur:
1. Valid IP address via DHCP
2. Valid IP address via Zeroconf
3. No connection/link (Check thestatus LED of the camera!)
As supplied, the camera attempts to get an IP address from a DHCP server in the network.
DHCP
The camera is assigned a valid IP address by the DHCP server. You can log on to the camera using the IDS
NXT cockpit and set the network parameters.
The PC network card must be in the same subnet as the camera to find the camera via the
IDS NXT cockpit.
Zeroconf
In an IPv4 network with no DHCP server, the camera in DHCP mode uses the Zeroconf method to
independently acquire a valid IP address from the reserved link-local address range. You can use the IDS
NXT cockpit to assign a different IP address to the camera. You can then to log on to the camera and set the
network parameters.
Static IP address
After logging on to the camera, you can assign a static IP address in IDS NXTcockpit, see Network
configuration in IDS NXTcockpit.
8.3 Starting IDS NXT cockpit
Start the IDS NXT cockpit.
· Windows: either via the icon on the desktop or under "Start > All Programs > IDS > IDS NXTcockpit“.

2021-04-13 15
IDS NXT: Setup IDS NXT rio
The first time the programis started, a firewall security prompt is displayed. Allow firewall
access to all networks (domain network, private networks and public networks).
In Windows Defender Firewall, IDS Vision Cockpit must have the following permissions (Control Panel\All
Control Panel Items\Windows Defender Firewall\Allowed Apps):
Fig. 5: Firewall settings
After launching, you will be in the Finder ("device overview"). IDS NXTcockpit scans the network for IDS NXT
cameras and lists them in this overview. A login to IDS NXTcameras is possible by direct entry of an IP
address.
Automatic finding of IDS NXTcameras only works if the following parameters are possible in
the network:
· UDP broadcasts via port 5055 ("Finder” queries fromIDS NXT cockpit)
· TCP response from devices via port 5055
· UDP broadcasts via port 3956 (GVCP - GigE Vision Control Protocol)
You can see more detailed information about the found devices when you select a device.

2021-04-13 16
IDS NXT: Setup IDS NXT rio
Fig. 6: IDS NXT cockpit shows a camera with its device information
Via "Connect" you get to the respective device logon.
8.4 Logging on to the device
Via the selection, select the user class that you want to use to log on to the device. There are three basic user
classes that are used.
· Administrator
The administrator profile allows full access to the IDS NXTcamera’s configuration. You can do everything
fromfirmware updates to installing and setting up IDS NXTvision apps.
· Service
This user profile can be used to perform service activities. Specified settings can be changed, for example
to respond to changed production specifications. These include camera settings (brightness, gain, ...) and
settings for the IDS NXTvision apps.
· User
This user profile provides shop floor employees, for example, with status information for an IDS NXTcamera
so that they can directly find information about fault conditions.
By default, the password for each user class is "ids". At the first login, you have to change
the password to be able to log on. When you log on with the administrator profile, you can
change the passwords for the user classes "Service" and "User". The procedure for this is
described in the IDS NXT cockpit manual.

2021-04-13 17
IDS NXT: Setup IDS NXT rio
Fig. 7: Log on
Initial login
1. Select the "Administrator" user class for login.
2. Enter the initial password. A dialog opens and you have to enter a new password for the user class.
Note: This dialog is only displayed if you use IDS NXT cockpit version 2.2 or higher!
3. Enter a new password. The password can have a maximum length of 255 characters. The following special
characters are not allowed: "?", "=", ":", and "&".
A lock is displayed behind the password field. Depending on the security of the password, the lock is red
(low security), yellow or green (high security).
4. Confirm the password. If the two entries are identical, a green check mark is displayed behind the
confirmation field.
You can viewthe entered passwords by pressing the eye symbol behind the input field with the mouse. As
long as you keep the mouse button pressed, the password is displayed.
5. Click on "Apply" to save the changes. Afterwards, you will be automatically logged on to the device.
It is recommended that you change the initial passwords for the other user classes as well.
8.5 Changing the IP address
If the IP address of the camera is not set correctly, the camera is displayed in the Finder with an exclamation
mark. With IDS NXTcockpit version 2.2 or higher, you can change the IP address of the camera in IDS NXT
cockpit.

2021-04-13 18
IDS NXT: Setup IDS NXT rio
Fig. 8: Incorrect IP address
1. Select the camera to change the IP address.
2. Click on "Change IP address".
à The dialog for changing the IP address opens.
3. Enter a new IP address for the camera. A suggestion based on your network settings will be displayed.
4. Click on "Apply" to change the IP address temporarily.
You can now log on to the camera and change the IP address permanently under "Configuration > Network".
8.6 Network configuration in IDS NXT cockpit
After logging onto a IDS NXTcamera, you will see the “Dashboard” which displays various device information.
To set the network parameters select "Configuration > Network".
· The "Obtain IP address automatically (DHCP)" option is activated by default. It is recommended to keep this
setting.
· You can use the device without DHCP and assign a static IP address to the device (not recommended).
Fig. 9: IDS NXT cockpit network configuration

2021-04-13 19
IDS NXT: Setup IDS NXT rio
9 Opening device website
Besides the IDS NXTcockpit, you can open a website that displays status information about the IDS NXT
camera. To do this, enter the IP address of the respective camera in your browser and log on. On the
website, you see the following information:
· Live image
Note: If you still use the default password for login, you will not see a live image (applies to cameras with
IDS NXTOS 1.2 and higher). You must first change the password in IDS NXTcockpit (see manual IDS
NXT cockpit).
· System monitor with status information
· Information about the device like IP address or location etc.
· Link to IDS NXTwebsite and license information
It is recommended to reload the device website after a firmware update, as websites are
automatically cached depending on the browser settings.
Fig. 10: Website with system status

2021-04-13 20
IDS NXT: Setup IDS NXT rio
10 HTTPS communication with SSL certificate
You have the possibility that you upload a SSL certificate to the camera and establish a secure connection
between the host PC and the camera. The following certificate types can be used:
· Self-signed certificate
This consists of a private key and a certificate file with a public key and details of the certificate. The server
must know the private key and the certificate file. On the client side, each self-signed certificate must be
trusted separately.
· CA-signed certificate (CA = certificate authority)
For this certificate type, first a certificate is created for the certification authority. The CA certificate itself is
a self-signed certificate consisting of a private key and the certificate file. The CA's private key is required
to sign the server certificate. Multiple server certificates can be created for different devices. These server
certificates also consist of a new private key and the original server certificate, which is signed by the CA.
For uploading to an IDS NXTcamera, you need an encrypted SSL package (*.NXT_SSL). You create this via
<%NXT-IDE%> using a script.
· Creating SSL package with existing certificates
· Uploading certificate to camera
· Optional: disable HTTP
Fig. 11: Configure HTTPS communication
If you use an SSL certificate, it is not necessary to make any further settings for IDS Vision
Cockpit, as IDS NXTcockpit uses a secure connection.
10.1 Creating SSL package with existing certificates
Prerequisites
· IDS NXTcamera with IDS NXTOS version 1.2.0 or higher
· <%NXT-IDE%> version 1.0 or higher
· SSL certificates in pem format
Preparing
1. Download the archive "ids-nxt-pack-certificate.zip" (see https://en.ids-imaging.com/downloads.html).