Spartan FH08-24 User manual

FH08-24
FH08-36
Fence Installer

TABLE OF CONTENTS
2
INTRODUCTION............................................................................................................................................3
ABOUT THIS MANUAL. ...............................................................................................................................3
GENERAL INFORMATION. .......................................................................................................................... 3
SAFETY INFORMATION. ............................................................................................................................. 3
SAFETY PRECAUTIONS. ............................................................................................................................4
MACHINE DESCRIPTION. ...........................................................................................................................5
OPERATING SAFETY .................................................................................................................................. 6
MAINTENANCE. ..........................................................................................................................................7
OPERATING INSTRUCTIONS. .................................................................................................................8-9
FH08-24-CLS…........................................................................................................................................10
FH08-36-CLS............................................................................................................................................. 11
FH24-2X(24”-2FTExtension)…....................................................................................................................12
FH24-4X (24” - 4 FT Extension)… ............................................................................................................... 13
FH36-2X(36”-2FTExtension)…....................................................................................................................14
FH36-4X (36” - 4 FT Extension)… ............................................................................................................... 15
FHS99(Chain Link Streching)…....................................................................................................................16
FHWP… ....................................................................................................................................................... 17
FHWS99-24(Wovenwire Stretcher) ................................................................................................................18
FHWS99-36 (Woven wire Stretcher)............................................................................................................19
TASCHEMATIC…........................................................................................................................................20
TILT..............................................................................................................................................................21
NOTES / SERVICE RECORDS...................................................................................................................22
WARRANTY.................................................................................................................................................23
WARRANTY REGISTRATION.................................................................................................................... 24

INTRODUCTION
3
ABOUT THIS MANUAL
GENERAL INFORMATION
SAFETY INFORMATION
Congratulations on purchasing one of the finest pieces of construction equipment on the market today!
If this is your first Spartan Equipment product, you will not be disappointed. If you have previously
owned a Spartan Equipment product, you will find the same high quality and dependability that you
have come to expect from Spartan Equipment.
The purpose of this manual is to inform the owner/employer/and the operator, how to safely operate
this piece of equipment, and make them aware of any hazards. It also contains important information
regarding assembly, set up, operation, and maintenance. It is the Owner/Employer’s responsibility
to make sure that anyone who operates this machine understands all safety warnings. If you do not
understand any items in this manual, please contact the dealer where this product was purchased, or
the manufacturer at the number listed throughout this manual. If you have any suggestions about how
to make this manual easier to understand, contact the manufacturer. Keep this manual available for
reference wherever this piece of equipment is being used and make it available to any operators.
Illustrations in this manual may show details or components that may not be the same as your
machine. Continuing improvements to the design of this machine may have caused changes that are
not included in this manual. The information in this document is subject to change without notice.
The following safety symbols and signal words will be used throughout this manual and on the
product, for your safety and the safety of others, please become familiar with their meaning and heed
their warnings.
This symbol, either used alone or with a signal word, is used to call your attention
to instructions involving your safety and/or the safety of others. Failure to follow
these instructions will likely result in personal injury or death.
DANGER
This signal word is used to identify a hazard which, if not avoided, will result in
death or serious injury.
WARNING
This signal word is used to identify a hazard which, if not avoided, could result in
death or serious injury.
CAUTION
This signal word is used to identify a hazard which, if not avoided, could result in
minor or moderate injury.
NOTICE
This signal word is used to identify a hazard which, if not avoided, could result in
property or equipment damage. It also may be used for special instructions
related to performance, maintenance or general items.

4
SAFETY PRECAUTIONS
WARNING
Failure to obey the following safety instructions could result in DEATH or
SERIOUS INJURY.
Read and understand entire manual before operating the Fence Hog.
For your safety and the safety of others, replace any missing or damaged warning decals by contact-
ing the manufacturer at 1-800-417-9272.
Make sure anyone operating the Fence Installer is thoroughly familiar with its operation. Keep all
unauthorized and untrained personnel, especially children, away from Fence Installer
Improper maintenance can be hazardous. Read and understand this section before you perform
any maintenance, service or repairs.
General Safety
• This machine is heavy and must not be lifted single-handedly; either get help or use suitable lifting
equipment..
• This machine is to be used for is intended application only.
• This machine must only be operated by well-trained personnel.
• The owner of this machine must observe, and train the user to observe, the effective laws of labor
protection in the country of application.
• Personal Protective Equipment (PPE) must be worn by the operator whenever the equipment is
being used.
• Cordon off the work area and keep members of the public and unauthorized personnel at a safe
distance.
• This machine must be operated on ground where stability is guaranteed. When working near the
rim of excavated trenches, use the machine properly so that the machine may not fall down or
collapse the excavation.
• Never remove or tamper with any fitted guards; they are there for your own protection. If they are
damaged or missing, DO NOT USE THE MACHINE until the guard has been replaced or repaired.
• Do not operate the machine when you are ill, feeling tired or when under the influence of alcohol or
drugs.
• This machine is designed to eliminate the possible risks arising from the use of it. However, risks
DO reside, and these residual risks are not clearly recognizable and may cause personal injury or
property damage, and possibly death. If such unpredictable and unrecognizable risks become
apparent, the machine must be stopped immediately, and operator or his supervisor must take
appropriate measure to eliminate such risks. It is sometimes necessary that the manufacturer must
be informed of such event for future counter measuring.

MACHINE DESCRIPTION
5
Dispenses Woven Wire, Chain Link, and Other Fence Types
EASY FENCING, EVERY TIME
Developed with the assistance of professional fence builders, the Fence Installer unit was designed to
satisfy customer requests for a machine that picks up and dispenses cumbersome rolls of chain link fence
easily, with no physical effort.
Powered by the hydraulic used in the Skid-Steer Loader, the uniquely designed cage mechanism opens
and tilts to retrieve the fence roll from the ground. For the fence contractor, this means no more unrolling
fence by hand and using extra men to stand it up.
FH08-24 / FH08-36

OPERATING SAFETY
6
1. The Fence Installer is a fence-dispensing device. Used outside of this scope may cause damage to
equipment or could result in injury, or death.
2. Make sure anyone operating the Fence Hog
3. ® is thoroughly trained with its operation. Keep all un
authorized and untrained personnel, especially children, away from the Fence Hog.
4. Consult lift equipment manufacturer’s specifications to ensure load capacity is not exceeded.
Model Empty Weight With 4ft. Extension
FH08-24 1150lbs. (521.6 kg) 1500lbs. (680.4 kg)
FH08-36 1350 lbs. (612.3 kg) 1775lbs. (805.1 kg)
Do not exceed Maximum Gross Weight.
5. Always make sure Fence Installer is securely fastened to skid steer.
6. Stay clear of gate opening while machine is running. Keep all body parts, solid objects, clothing,
and jewelry away from all moving parts.
7. Never perform any work on the Fence Hog while it is running. Before working on the
Fence Installer, stop skid steer and disconnect the hydraulic hose to prevent accidental starting.
8. Avoid contact with hot hydraulic fluid. Allow system to cool before performing any repairs or
service.
9. Never stand under an elevated Fence Hog.
10. Never ride the Fence Installer.
11. Never operate the Fence Installer under the influence of alcohol, drugs, or medications.
12. Use only factory authorized parts.
13.Inspect all hoses and components for cracks, leaks, abrasions, and general wear before
each use. Replace if damaged before using.
14. Inspect all hoses and fittings for signs of damage, wear, scrapes, kinks or cracking. Replace
hoses if any of these conditions are found. It is recommended to replace all hydraulic hoses
every 5 years.
14. Always wear approved safety glasses and hard hats when operating or servicing a Fence
Installer®.
15. Do not use the Fence Installer as a lifting device and do not load more than one roll of fence
fabric or wire in the Fence Installer at a time.

7
Grease fittings located on the Fence Installer and Extension. See drawing for location of fittings. All grease
fittings should be greased before each use with EPI rated or equivalent grease.
Obtaining Spare Parts
Spare parts for your Fence Installer may be obtained by the following procedure.
1. Record the Model number and Serial Number from the Serial Number Tag located on the valve mount
bar of the Fence Installer.
2. Using the parts reference table in this manual, record part number, serial number, and component.
3. Contact your local Fence Installer dealer or Spartan Equipment at 1-888-888-1085 with the serial
number, part number, and component.
Warning Decals - for your safety and the safety of others, replace any damaged or missing
warning decals by contacting the manufacturer at 1-888-888-1085.
MAINTENANCE

OPERATING INSTRUCTIONS
8
Loading Wire
1. Attach the Fence Installer to your skid steer. Consult skid steer owner’s manual for attachment procedure.
2. Connect hydraulic hoses to skid steer auxiliary hydraulic couplers.
3. Using the auxiliary hydraulics, cycle all hydraulic motions to verify the Fence Installer is operating
correctly. Verify that the cage opens and closes completely and moves smoothly throughout its travel of
operation.
4. Open the Fence Installer to its widest point and position your skid steer so that a roll of wire is directly
in front of it.
5. Then lift the boom and tilt the Fence Installer down.
6. Move the skid steer forward until the turntable of the Fence Installer aligns with the bottom of the roll
of fence.
7. Lower the Fence Installer over the roll of wire and begin closing the gates. Once the gates are
mostly closed, lift the boom and tilt the Fence Installer up.
8. The roll of wire will fall back into the cage of the Fence Installer. Close the Fence Installer tightly.
Note: For Woven Wire - Install Roll Centering Rod through the center of roll and into turntable to hold roll
upright by removing the Roll Centering Rod from the square tube on the back of the Fence Installer and
sliding it through the center of wire roll and into the hole in the turntable. Then, install Centering Rod support
over Centering Rod.

OPERATING INSTRUCTIONS
9
4 WARNING!
1) Pinch point. Keep hands clear.
2) Stay clear of moving parts while
machine is in operation.
3) Keep all body parts, solid objects,
clothing, and jewelry away from
moving parts and hinges.
Before using this
equipment, study entire
Owner’s Manuals.
Installing Fence
1. After loading a roll of wire, move the skid steer parallel to the row of fence posts and
attach the beginning of the roll to the first fence post.
2. Slowly drive the skid steer along the fence line and the roll will start to unwind. Continue
to desired point.
Standard Chain Link Stretcher: At stretching point, pull Handle and rotate Stretching
Bar until fingers point outward. Insert fingers through the fabric. Skip to Step 3.
Optional Woven Wire Stretcher: Install optional woven wire stretcher to the gate
ends. Using the holes provided, drive the wedges into stretcher to hold wire, then drive
forward to stretch to desired tension.
3. Maneuver the skid steer so the fabric is aligned with the fence line. DRIVE FORWARD
to stretch to desired tension.
4. Attach fabric to post once desired tension is reached.
5. Relieve pressure on fabric (remove locking wedges if applicable) and return stretcher to
stowed position.
6. Repeat steps 1 through 5 as needed.
WARNING LABELS
Owners Manual: Located on frame. Pinch Label: Located on gates where gates attach
to frame and where gates come together.

FH08-24-CLS
10
5
1
24
39
30
27
4
22
3 31
23
25
32
22
33
18
16
11
10 2
35
35
20
5
33
9
34
21
19
6
4
3
38 36
23
14
15
7
13
17
12
8
28
FH08-24-CLS
ITEM
QTY
PART NUMBER
DESCRIPTION
20
1
FH-518
Brake Rod
21
1 FH-547
Brake Rod Spacer
22 2 09-409
Knob Spring
23 2 FH-A-4
Drive Forward Outrigger
24 1 FH24-A-7
Upper Drive Forward Outrigger Pocket Assembly
25 1 FH-538
Drive Forward Arm
26 1 FHS99
Chain Link Stretcher 99"
27 4 09-425 Bent Pin
28 2 09-103
1/2" Lock Washer
29 2 09-317
1/2" - 13 x 1.5" Grade 5 Bolt
30 1 02-6016
Relief and Holding Valve Assembly
31 1 02-634
Deltrol Bi-Directional Relief Cartridge
32 2 FH-A-6
Supply Hose Assembly
33 2 02-2114
1/2" Male x 1/2" female street 45º
34 1 02-221
1/2" Female Disconnect
35 1 02-222
1/2" Male Disconnect
36 2 FH24-A-9
Left Cylinder Hose Assembly
37 2 FH24-A-10
Right Cylinder Hose Assembly
38 2 02-708
Hydraulic Cylinder 2" bore x 4" Stroke
39 5 Hanger Hog Hanger
ITEM QTY PART NUMBER DESCRIPTION
1 1 FH24-A-1
Frame Welded Assembly
2 1 FH-A-9
Universal Attachment Plate
3 10 09-208
1/2" -13 Nylon Nut
4
12 09-107
1/2" Flat Washer
5
10 09-325
1/2"-13 x 1 3/4" Grade 5 Bolt
6 3 09-319
5/8"-11 X 2 3/4" Grade 5 Bolt
7 3 15-139
Support Cam Roller
8 3 09-210
5/8"-11 Nylon Nut
9 1 FH24-A-14
Turntable Assembly
10 2 09-104
1/4" Flat Washer
11
2 09-202
5/16"-18 Nylon Nut
12
1
09-355
3/8"-16 x 3/4" Grade 5 Bolt
13 1 09-600
1/8" 90º Grease Fitting
14 1 09-407
Latch Pin
15 1 09-105
5/16" Flat Washer
16 2 09-303
5/16"-18 x 1 1/2" Grade 5 Bolt
17
2 09-102
3/8" Lock Washer
18
1
FH24-A-12
Brake Handle Assembly
19 1 FH24-A-13
Turntable Brake Stop Assembly
26
29

FH08-36-CLS
11
5
24
39
27
22
23
4
3
25
30
22
31
18
16
32
11
2
10
5
37
33
20
34
33
35
9
21
19
4
23
38
28
15
3
12
13
6
37
17
14
8
7
29
FH08-36-CLS
ITEM QTY
PART
NUMBER
DESCRIPTION
20 1 FH-518 Brake Rod
21
1 FH-547
Brake Rod Spacer
22 1 09-409 Knob Spring
23 2 FH-A-4
Drive Forward Outrigger
24
1
FH36-A-7 Upper Drive Forward Arm Pocket Assembly
25 1 FH-538 Drive Forward Arm
26 1 FHS99
Chain Link Stretcher
27 2 09-425
Bent Pin
28 2 09-103 1/2" Lock Washer
29 2 09-317
1/2" -13 x 1 1/2" Grade 5 Bolt
30
1
02-6016 Relief and Holding Valve Assembly
31 1 02-634 Deltrol Bi-Directional Relief Cartridge
32 2 FH-A-6
Supply Hose Assembly
33 2 02-2114 1/2" Male Pipe x 1/2" Female Pipe Street 45º
34 1 02-221 1/2" Female Disconnect
35 1 02-222
1/2" Male Disconnect
37
1
FH36-A-9 Left Cylinder Hose
37 1 FH36-A-10 Right Cylinder Hose
38 2 02-708
Hydraulic Cylinder 2" bore x 4" Stoke
39
1 Hanger Hog Hanger
ITEM QTY
PART
NUMBER
DESCRIPTION
1 1 FH36-A-1
Welded Gate and Frame Assembly
2
1
FH-A-9 Universal Skidsteer Attachment Plate
3 10 09-208 1/2" -13 Nylon Nut
4 12 09-107
1/2" Flat Washer
5
10 09-325 1/2"-13 x 1 3/4" Grade 5 Bolt
6 3 09-319 5/8"-11 X 2 3/4" Grade 5 Bolt
7 3 15-139
Support Cam Roller
8 3 09-210 5/8"-11 Nylon Nut
9 1 FH36-A-14 Turntable
10 2 09-104
1/4" Flat Washer
11
2 09-202 5/16"-18 Nylon Nut
12 1 09-355 3/8"-16 x 3/4" Grade 5 Bolt
13 1 09-600
1/8" 90º Grease Fitting
14 1
09-407 5/16" Latch Pin
15 1 09-105 5/16" Flat Washer
16 2 09-303
5/16"-18 x 1 1/2" Grade 5 Bolt
17
2 09-102 3/8" Lock Washer
18 1 FH36-A-12 Turntable Brake Handle Assembly
19 1 FH36-A-13
Turntable Brake Stop Arm Assembly
26

FH24-2X (24” - 2 FT. EXTENSION)
12
PARTS LIST
4
1
3
8
8
2
FH24-2X
5
7
6
ITEM QTY PART NUMBER DESCRIPTION
1 1 FH24-2X-A-1 2ft. Extension Welded Frame and Gate Assembly
2 8 09-208 1/2" -13 Nylon Nut
3 8 09-328 1/2" -13 x 2" GR8 Bolt
4 1 FH-A-5 2ft. Extension Drive Forward Arm Assembly
5 1 FHS-A-4 2ft. Extension Chain Link Stretcher Bar
6 2 09-210 5/8"-11 Nylon Nut
7
2 09-362 5/8"-11 x 2" GR8 Bolt
8 16 09-107 1/2" Flat Washer

FH24-4X (24” - 4 FT. EXTENSION)
13
PARTS LIST
FH24-4X
1
7 6
12
9 11 2
14
5
3 13
8 12
14
10
3
13
11 4
10
13
14
13
10
14
10
ITEM QTY PART
NUMBER DESCRIPTION
1 1 FH24-4X-A-1 4ft. Extension Welded Frame and Gate Assembly
2 2 02-708 Hydraulic Cylinder
3 16 09-107 1/2" Flat Washer
4
8 09-208 1/2" -13 Nylon Nut
5
8 09-328 1/2" -13 x 2" GR8 Bolt
6
1 FHS-A-5 4ft. Extension Chain Link Stretcher Bar
7 1 FH-A-8 4ft. Extension Drive Forward Arm Assembly
8 2 09-210 5/8"-11 Nylon Nut
9 2 09-362 5/8"-11 x 2" GR8 Bolt
10
4 FH-A-12 4ft. Extension Hose Assembly
11
2 FH-A-13 4ft. Extension Left Cylinder Hose Assembly
12 2 FH-A-14 4ft. Extension Right Cylinder Hose Assembly
13
4 02-2117 Male QD Coupler-Conn Pres 3/8"Body-½”NPT
14 4 02-2118 Female QD Coupler - 3/8 Body With ½” NPT

FH36-2X (36” - 2 FT. EXTENSION)
14
PARTS LIST
4
5
7
6
1
3
8
8
2
FH36-2X
ITEM QTY PART
NUMBER DESCRIPTION
1 1 FH36-2X-A-1 2ft. Extension Welded Frame and Assembly
2 8 09-208 1/2" -13 Nylon Nut
3 8 09-328 1/2" -13 x 2" GR8 Bolt
4 1 FH-A-5 2ft. Extension Drive Forward Arm Assembly
5 1 FHS-A-4 2ft. Extension Chain Link Stretcher Bar
6 2 09-210 5/8"-11 Nylon Nut
7
2 09-362 5/8"-11 x 2" GR8 Bolt
8 16 09-107 1/2" Flat Washer

FH36-2X (36” - 4 FT. EXTENSION) FT. EXTENSION)
15
PARTS LIST
FH36-4X
1
7
6
12
2
14
5
13
11 3
9 10
11 3 12
4
13
8 14
14
13
10
10 13
14
10
ITEM QTY PART NUMBER DESCRIPTION
1 1 FH36-4X-A-1 Welded Frame and Gate Assembly
2 2 02-708 Hydraulic Cylinder
3 16 09-107 1/2" Flat Washer
4
8 09-208 1/2" -13 Nylon Nut
5
8 09-328 1/2" -13 x 2" GR8 Bolt
6
1 FHS-A-5 4ft Extension Chain Link Stretcher Bar
7 1 FH-A-8 4ft Drive Forward Arm Assembly
8 2 09-210 5/8"-11 Nylon Nut
9 2 09-362 5/8"-11 x 2" GR8 Bolt
10
4 FH-A-12 4Ft. Extension Hose Assembly
11
2 FH-A-13 4ft Extension Left Cylinder Hose Assembly
12 2 FH-A-14 4ft Extension Right Cylinder Hose Assembly
13
4 02-2117 Male QD Coupler-Conn Pres 3/8"Body-½”NPT
14 4 02-2118 Female QD Coupler - 3/8 Body With ½” NPT

FHS99 (CHAIN LINK STRETCHER)
16
PARTS LIST
21
19
18
20
15
17
5
16
14
23
4
2
FHS99
ITEM
QTY
PART NUMBER
DESCRIPTION
1 1 FHS-A-1
Chain link Stretcher Welded Assembly
2 3 09-109 5/8" Flat Washer
3
1
FHS-A-3 Stretcher Lower Mount
4
2 09-425
Bent Pin
5
2 09-361 3/8" x 3/8" x 5/16" Thread Shoulder Screw
6
1
09-800
Return Spring
7 1
FHS-10 Stretcher Lower Cable Guard
8
4
09-352 #10-32 x 1/2" Thread Cutting Screw
9 2 09-107 1/2" Flat Washer
10
1
09-801 Latch Spring
11 1
09-417 1/4" x 1" Roll Pin
12
1
FHS-11 Latch Pin
13
1
09-802 Control Cable
14 1
FHS-8 Stretcher Handle
15 1
09-803 Cable Clevis
16 2 09-105 5/16" Flat Washer
17 1
09-203 5/16" - 18 Nut
18
1
FHS-6 Stretcher Handle Mount Plate
19
1
FHS-7 Stretcher Backing Plate
20
4
09-306 5/16" - 18 x 3" Grade 5 Bolt
21
4
09-104 1/4" Flat Washer
22
4
09-202 5/16"-18 Nylon Nut
23
1
FHS-A-2 Stretcher Upper Mount
DETAIL C
DETAIL B
DETAIL A
A
13
1
B
C
22
7
1
8
12
11
6
10
5
9
2
3

FHWP
17
PARTS LIST
ITEM
QTY
PART NUMBER
DESCRIPTION
1 4
FH-WP-12 Mount Plate
2
4
09-381
1/2" -13 x 5" Grade 8 (Zinc)
3
4
09-396 1/2" -13 x 2 1/2" Grade 5 Carriage Bolt
4
16 09-208
1/2" -13 Nylon Nut
5 4
09-806 Spring Snap Chain Clip
6 2 20-111
3/16" Chain 1 1/2' long
7 1
FHWP-A-2 Welded Bracket Assembly
8
1 FHWP-A-1
Welded Platform Assembly
9 2
FH-WP-4
Removable Cross Bar
10
4
09-316
1/2"-13 x 1 1/4" GR5 Bolt
11 4
09-397 1/2" -13 x 6" Grade 5 Carriage Bolt
11
6
9
5
4
10
8
3
7
2
1
FHWP
LEFT SIDE
RIGHT SIDE

FHWS99-24 (WOVEN WIRE STRETCHER)
18
PARTS LIST
DETAI
L
A
9
A
1
8
1
B
4
1
7
13
12
10
11
5
3
15
DETAIL B
FHWS99-24
ITEM QTY
PART
NUMBER
DESCRIPTION
1 1
FHS-A-7
Woven Wire Stretcher Welded Assembly
2
1
FHS-A-2
Stretcher Upper Mount
3
1
FHS-A-3
Stretcher Lower Mount
4 1
FHS-17
Woven Wire Stretcher Handle
5
3 09- 109
5/8" Flat Washer
6 2 09- 425
Bent Pin
7 1
FHS-10
Stretcher Lower Cable Guard
8
1
FH-A-2 Woven Wire Centering Bar
9
1
FH24-A-3
Roll Centering Rod Support Assembly
10
1
09- 801
Latch Spring
11
2 09- 107
1/2" Flat Washer
12
1
09- 417
1/4" x 1" Roll Pin
13
4
09- 352
#10-32 x 1/2" Thread Cutting Screw
14
10 FH-24-35
Woven Wire Stretcher Wedge
15 1
FH-24-34
Field Fence Shoe
2
6
5
1
14

FHWS99-36 (WOVEN WIRE STRETCHER)
19
PARTS LIST
15
2
9
6
5
1
A
8
1
1
B
DETAIL A
ITEM QTY
PART
NUMBER
DESCRIPTION
1 1 FHS-A-7
Woven Wire Stretcher Welded Assembly
2 1 FHS-A-2
Stretcher Upper Mount
3 1 FHS-A-3
Stretcher Lower Mount
4 1 FHS- 17
Handle For Woven Wire Stretcher
5
3 09- 109 5/8" Flat Washer
6
2 09- 425
Bent Pin
7 1 FHS- 10
Stretcher Lower Cable Guard
8
1 FH-A-2
Woven Wire Centering Bar
9 1 FH36-A-3
Roll Centering Rod Support
10 1
09- 801 Latch Spring
11 2 09- 107
1/2" Flat Washer
12
1 09- 417
1/4" x 1" Roll Pin
13
4
09- 352 #10-32 x 1/2" Thread Cutting Screw
14
10 FH-24-35 Woven Wire Stretcher Wedge
15 1 FH-24-34
Field Fence Shoe
DETAIL B
FHWS99-36
14
1
4
7
12
10
11
5
3
13

TA SCHEMATIC
20