IFYIL AVANOS User manual

0
2019
SOLID FUEL HYDRO
STOVE / COOKER USERGUIDE
TRUVA & ABAN
Rev.No 2019.1.1

1

2
Contents
INTRODUCTION ............................................................................................ 4
1. IMPORTANT NOTICE ............................................................................ 5
1.1. General Safety Warnings ................................................................ 5
1.2. Operating Warnings ............................................................................ 6
2. TECHNICAL SPECIFICATIONS ...................................................................... 6
3. FUEL SPECIFICATION ........................................................................... 9
4. INSTALLATION................................................................................... 11
4.1. Operating Environment................................................................. 11
4.2. Electrical Connections................................................................... 12
4.3. Plumbing Connections .................................................................. 13
4.3.1. Plumbing Schema.................................................................. 15
4.3.2. Open Expansion Tank ............................................................ 17
4.3.3. Plumbing Water Specification.................................................. 18
4.4. Ventilation And Air Flow................................................................ 18
4.5. Chimney Instructions.................................................................... 19
4.6. Smoke Pipe Instructions ............................................................... 20
4.7. Suitable Shapes Of Chimney and Connections................................. 21
5. OPERATING ....................................................................................... 23
5.1. Pre-Operation Warnings................................................................ 23
5.2. Fuel Loading Process.................................................................... 23
5.3. Combustion Control...................................................................... 24
5.4. Initial Ignition .............................................................................. 25

3
6. OVEN HANDLING AND COOKING INSTRUCTIONS ................................. 25
7. USED HARDWARES OF STOVE............................................................. 27
7.1. Thermostat Use And Specifications ................................................ 27
7.2. Use Of Mechanical Air Flap............................................................ 28
7.3. Use Of Shaking Rods.................................................................... 29
7.3.1. Cleaning The Grat.................................................................. 29
7.3.2. Ash Eliminate ........................................................................ 30
7.4. Use Of Smoke Flap (Star) ............................................................. 31
8. MAIN PARTS AND DIMENSIONS.......................................................... 32
9. PUMP WARNING LAMP........................................................................ 37
10. MAINTENANCE and CLEANING ............................................................ 38
11. PROBLEMS, CAUSES and SOLUTIONS................................................... 42
12. SIGNIFICIANT INSTRUCTIONS for EFFECTIVE USING............................ 45
13. SUGGESTIONS and FEEDBACK............................................................. 46
GARANTİ BELGESİ ................................Hata! Yer işareti tanımlanmamış.
GARANTİ ŞARTLARI..............................Hata! Yer işareti tanımlanmamış.
CERTIFICATE OF WARRANTY.................................................................. 47
WARRANTY CONDITIONS........................................................................ 48

4
INTRODUCTION
Dear Friend of İFYIL;
İFYIL TERMO İKLİMLENDİRME SAN. Ve TİC. LTD. ŞTİ. we manufacture the
most efficient hydro stoves with utmost care for our distinguished
customers. So, please read this userguide carefully before starting to use
our stove and keep it as a reference in any case.
Information
This symbol high lightens the significant details for correct usage of
stove. If the warnings are ignored, product will not be fully correct &
regular and this can cause customer not satisfaction.
Attention
This symbol high lightens the possible serious risks during operation
of stove. So this user guide should be read carefully before using the
stove and utmost attention should be paid to the warnings.

5
1. IMPORTANT NOTICE
1.1. General Safety Warnings
Please, carefully read the manual to get the best yield from the stove
The product should be installed in accordance with the legislation of the
country in which it will be used and the necessary safety precautions should
be taken. Otherwise IFYIL will not accept any responsibility.
Any change on the stove should be done by authorized person.
Spare parts should only be used by the recommended manufacturer.
IFYIL hydro stoves must be installed according to the installation schema.
During the burning of your stove, the outer surfaces of the stove (doors and
glasses, exterior plates, stove base, etc.), heating surface (casting etc.),
metal handles, pipes and the inside of the oven should be careful as it is
hot.
Definitely do not fire the stove while in the lack of water.
Do not fill the water in the stove and the installation system by the safety
valve.
Should be fired the stove after the air is blown from the calorific stove and
installation system.
The chimney should be cleaned at least 2 times per year.
Flammable materials should be kept away against the fire risk.
Install the product in locations equipped with fire risk.
Stove base (glass, ceramic, marble etc.) are recommended in Wood and
laminate parquet floors for stoves.
İFYIL stoves should not be installed in the places where people sleep.
Stoves are recommended to be avoided in places where sleep.
The stove should never be installed in the presence of flammable gases and
materials.
Never use flammable liquids and gases in the combustion chamber.
The product should only be used as intended. Different uses cause hazards.
The stove should not be operated when the lid is open or the glass is
broken.
Please comply with these rules if there are local rules or norms for the solid
fuel chimney according to country regulations. If there are no local norms,
must be comply with EN 13384-1.

6
1.2. Operating Warnings
Assembly of İFYIL stoves and fireplaces; Electrical connections and
installation should be done in accordance with the scheme.
IFYIL stoves are suitable for home, office and interior. IFYIL stoves balcony,
warehouse, bathroom etc. should not be installed in such areas.
In domestic use, such as kitchen, living room, entrance hall; Use in places
such as cafes, restaurants, workplaces.
We do not accept any responsibility for any problem due to the outdoor
installation of stove.
İfyıl stoves must not be installed into open, moisture, idle places etc.
If the radiators are not heated, the system is checked for air. Radiators
should be taken if there is air.
The heat requirement of the place to be installed must be calculated and
the appropriate stove selection must be made.
Fuel should be checked if wet or not. Fuel should not be damp.
The inside of the stove should not wash with water.
If there is a fire in the chimney pipe, close the stove and contact the
competent authorities.
Periodically check the smoke outlet duct.
If the product does not work properly, please turn it off.
Customers not obeying the above requirements and schemas
cannot claim any right for any problem. In any case, contact your
dealer or IFYIL.
2. TECHNICAL SPECIFICATIONS
This device should be installed in accordance with the related regulation and EU standards.
 EN 13240 - Roomheaters fired by solid fuel-Requirements and test methods.
 EN 12815 - Residential cookers fired by solid fuel - Requirements and test
methods (Star)
 2014 / 68 / EU –Pressure equipment directive

Technical Specifications
Measured Values
Device type/model; Solid Fuel Hydro Stove
ROASTER
SUPERNOVA
SAUNA
HAMMAM
STAR
Nominal heat output
Wood
kW
20
29
20
20
23
Briquette
kW
21
30
21
21
24
Coal
kW
32
38
32
32
34,5
Water heating power
Wood
kW
16
25
16
16
18
Briquette
kW
17
26
17
17
18
Coal
kW
26
34
26
26
27
Space heating power
Wood
kW
4
4
4
4
5
Briquette
kW
4
4
4
4
6
Coal
kW
6
4
6
6
7,5
Efficiency
%
80
80
80
80
84,93
Fuel type
Wood, Briquette, Coal
Fuel loading zone
Front loading
Top loading
Top-Front loading
Primer burning air control
Half Automatic
Seconder burning air control
Manual
Permissible
operating
temperature
Maximum
⁰C
80
Minimum
⁰C
40

Permissible maximum o perating
pressure
bar
2
Test pressure
bar
4
Boiler water volume
L
39
64
39
39
39
Recommented flue pipe draft
Pa
18
Weight
Stove
kg
229
211
182
180
296
Dimensions
(Width x Depth x
Height)
Stove
mm
650x745x1146
650x745x1146
650x745x880
650x745x880
1158x733x924
Oven
mm
320x480x175
-
-
-
367x495x260
Connections
Water
round-trip
connections
inch
1
Expansion
tank
connections
inch
3/4
Chimney
connection
mm
Ø130
Ø130
Ø130
Ø130
Ø150
Electric Consumption
W
45
45
45
45
45
Electiric connection
Vac/Hz.
230/50
CO Emission for %13 O2
mg/m3
935,25
935,25
935,25
935,25
1477

9
3. FUEL SPECIFICATION
In order to achieve the maximum performance of IFYIL stoves; Calorific value
and properties of the fuel to be used is very important. The calorific value of the
fuel depends on the humidity and density. The tendency of the moist fuel to
burn is low. The humidty in the fuel provides less heat as more energy is
needed to evaporate. The yield / performance of the product may vary
depending on the type of fuel used. Please observe the following when selecting
/ using the fuel. Otherwise, IFYIL will not accept any responsibility for
your problems related to heating and any faults that may occur.
For Wood;
The wood logs to be used should have a moisture content of less than 20% and
should be stored in a dry place. The use of damp wood, the soot can
accumulate in the chimney and may cause the formation of fire.
Not all trees have the same characteristics. Drying time and calorific value vary
according to the type of wood. Fresh (wet) wood is not suitable for combustion
because it has a moisture content of about 60%. It is therefore recommended
that fresh (wet) wood be dried in a dry and ventilated place for at least two
years before use.
The wood from resinous trees creates a lot of soot, often requires
more chimney and stove cleaning and can shorten the life of your
device.
Continuous and long-term use of aromatic trees (eucalyptus, myrtle,
etc.) will damage the grill portion of the product.

10
For Briquette;
The briquettes to be used must have a moisture content of less than 12% and
should be stored in a dry place. The use of damp briquettes may cause fire in
the chimney due to accumulation of soot in the chimney.
For Coal;
The coal to be used must have a moisture content of less than 20%, low ash
content of less than 14% and a sulfur content of less than 1%. High levels of
moisture and sulfur in coal content can cause sulfuric acid and serious damage
to your stove. Caloric value of coal to be used should be at least 5000 - 7000
kcal / kg. Lemon-sized coal should be used for a good burning.
The following substances should not be used as fuel.
 Moist / Wet fuels (Wood, Coal, Briquette)
 Contains high carbon materials.
 Painted wood.
 Hardboard wastes
 Waste materials (textile products, plastics, pouches, petroleum waste etc.)
 Flammable / combustible / flammable / explosive gases and liquids.
 Dust or hazelnut size type of coal.
The boiler structure and mechanical parts may be damaged if used.
When there is no flame in the combustion chamber, a high
amount of smoke may be generated when the fuel is loaded
onto the embers; this may contain explosive gas-air mixture
in the smoke content and may cause explosion risk.

11
4. INSTALLATION
This stoves product for houses, offices and internal places.
İFYIL stove should not be installed in areas such as balconies, bathrooms,
warehouses. In case of use outside of the interior, our company accepts no
responsibility for the problems related to heating.
There will be loss of energy and efficiency in balcony, warehouse or etc.
4.1. Operating Environment
It is recommended to put stove base (glass, ceramic, marble etc.) on
wooden and laminated parquet floors.
The floor should be smooth and of quality to carry stove weight.
Flammable products must be kept at a safe distance from the risk of fire.
Install the product in locations equipped with fire risk.
The product should be placed so that it can provide the air required its for
combustion.
The room volume 30 m³ shall not be less than.
When the stove installation is done, adjust the feet to ensure that the height
of the base is 4 cm.
The installation of the stoves should not be made to the places where
people sleep.
Safety Minimum Distance
Fireproofing Walls
A: ≥300 mm
B: ≥ 500 mm
C: ≥ 1200 mm (radiation area)
Figure - Safe Minimum Distance

12
If the stove is installed next to flammable wall, isolation for the
wall should be done.
If the base where the stove is to be installed is made of flammable
materials. If the stove is put on flammable material, suitable isolation must
be done.
Please keep away heat sensitive materials from stove (flammable, explosive
etc.).
4.2. Electrical Connections
First insert the power cable into the back of
the stove, then insert the cable outlet. It is
recommended to use a power supply against
prolonged power outages.
A voltage regulator using is required in areas with voltage irregularities.
Electronic and electronic card failures that may occur due to the absence of a
voltage regulator are not covered by the warranty.
Use your stove and running in a socket with ground.

13
4.3. Plumbing Connections
120 cm and longer radiator must be connected to the installation with a
reverse connection.
Definitly should had fill and drain valve in the installation
The safety valve is mounted on the body.
Boiler lit (off) the water pressure should be in the range of 1-1,5 bar.
Otherwise drain / refill valve should be checked.

14
It is recommended to install a thermostatic valve in the radiators to ensure
that the room temperature can be kept to the desired degree and to provide
high comfort at low cost.
EU standards. Half of the installation should be 1 '' (32 boiler installations),
half 3/4 '' (25 installation booths). Only the radiator braggings should be
1/2" (20 tubes). (Recommended cross-section pipe, composite pipe, copper
pipe, black iron pipe).
Hydro boiler’s connections must be made with conical iron union.
It is recommended to install an air purifier in the expansion line. (Installation
Schema)
It is recommended to use anti-scale magnetic solvent in the exchanger and
boiler for cold water inlet.
You can add water to installation system by including an external filling
valve in the return line of installation.
The valve 11 in the installation diagram allows the water to be drained in
the stove boiler and the installation.
Water is reinforced by turning half a turn from the installation water filling
valve.
The heat safety valve valve (5) must be left open.
The heat safety valve included in the product (Installation Scheme - 5 ) is
activated automatically in the event of an unexpected heat increase (>
85'C). On the one hand, while providing hot water discharge inside the
boiler, it also provides cold water to the boiler from the water line.
Frost protection measures must be taken. (Antifreeze).
There should be no sediment, dirt and undesirable solid particles within the
water content to be applied to the boiler and the installation, and the
drinking water quality installation water should be used.
If necessary, a strainer and lime trap must be used in front of the water
reinforcement pipes.
No particle, dirt, lime or chemical additives should not be in the plumbing
water to be used, aggressive waters of with corrosion should not be used.

4.3.1.Plumbing Schema
The image of the Avanos model is
included in the schema. The
distance between the connections
of Toros, Canik and Ilgaz models
may vary from product to product.

Model: Star

17
4.3.2.Open Expansion Tank
When water is heated from 10 ⁰C to 90 ⁰C, its volume increases by
about 3.55%. The surplus water that is heated and expands in the boiler is
collected in the expansion tank and the water of the installation is cooled and
the level is completed from here. Expansion tanks prevent increasing the
pressure of the system because of the expansion of the water in the installation.
In building heating systems, while providing the safety of the boiler and
the installation, it completes the losses due to the evaporation of the water in
the installation due to various leaks, repair and maintenance reasons.
In open expansion hot water heating system; it is essential that water is
in direct contact with air and its temperature does not rise above 100 ° C. Water
contact with air should not be obstructed.
Expansion tank connections must be made according to the installation
diagram.
Installation of the open expansion tank must be done above the highest
radiator (bath towel).
The valve must not be used in the return and return lines of the expansion
tank.
The return and return pipes cannot be used less than ¾”.
Imbisat water drain line (valve no 7) should be given to water drain.
In places where the air temperature is below 0 °C the expansion tank should
be in the house. Reinforced antifreeze should be used in these regions.
Water level of expansion tank should be checked once a week. If the water
level of expansion tank appers to below half level, fill the water with filling
valve.
Safety pipes must be installed without any downsizing and always rising
towards the expansion vessel.
It is mandatory to use open expansion tank in IFYIL solid fuel
stove and cooker.
In these systems, closed expansion cannot be used.
Otherwise, IFYIL will not accept any liability.

18
4.3.3.Plumbing Water Specification
Properties that should be in boiler water; EN 12953-10 “Shell boilers- Part 10:
Requirements for feedwater and boiler water quality”must comply with the
standard. In the boiler and heating system, water in quality of drink water
should be used in order to prevent damage caused by corrosion. Aggressive
water should not be used for chemical additives because of corrosion. The
water content to be filled in the boiler and the installation must not contain
residues, dirt and undesirable solid particles. These deposits and dirt are
extremely harmful to the circulation pump. If you are suspected that the water
is not clean, necessary precautions should be taken.
Calcified water used in the system forms a lime and mud layer on the heating
surfaces of the boiler. This lime and mud layer prevents water circulation and
heat transfer and deforms the boiler. This is not covered by the warranty.
4.4. Ventilation And Air Flow
In the room where the stove is installed, there should be enough air to allow
regular combustion.
The location of stove fresh air inlet must be provided.
It is recommended that the stove should be connected to an environment
(external environment) where the air suction pipe can be continuously
flowing clean air with hermetic pipe.
Use 300 cm² lower, 200 cm² upper orifice. These grilles should never be
closed. Otherwise, it presents a great danger.
Avoid installing the unit in the same environment with the following;
o B type gas heaters or exhaust fan or fan less hoods
o Collective ventilation pipes.
o Aspiratordevice running inthe same environment, cancauseproblems.

19
4.5. Chimney Instructions
 The main cause of the chimney fire;
Improper selection or pipe that dust is flammable fuel.
In the event of appropriate conditions can cause fires ignite in the ducts.
 Ways of avoiding them;
The chimney should be cleaned at least 2 times per year, depending on the
fuel quality.
Correct and appropriate chimney selection should be made.
Ensuring that the sealing and smoke in the chimney pipe and must be made
in isolation.
After installation, chimney cleaning must be done before ignition operation.
In case of a re-ignition after prolonged period of time, the smoke paths and
flue congestion must be checked.
Surrounding the peak point of the roof of the chimney to the interference of
the obstacle (the ridge) from height must be at least 80 cm.
Stove is not suitable for a shared chimney system.
There should be no cracks on the flue to prevent the flue gas from leaking.
The inner surface of the chimney should be smooth.
Should chimney's pipe inner diameter is 130 mm. (For star 150mm)
Chimney flue test should be performed before making connections. If the
chimney connections should be carried out after removal of the traction
problem had this problem in the chimney.
The stove pipe connected to the horizontal flue pipe must not be longer than
2m. It is recommended to use 45 ⁰elbows in chimney pipes instead of 90 ⁰
bend. (Site selection for stoves should be determined by the closest point
where the chimney.)
To avoid turbulence around the chimney flue without any obstructions (high
buildings, trees, etc.) Must be at least 10 m away.