iGaging AngleCube 35-222-6 User manual

ENJOY ACCURACY®
Specifications:
Resolution: 0.05"
Repeatability: 0.1"
Accuracy: ±0.2°
Battery: Standard 9 volt
AngleCube
®Angle Gauge
35-222-6
• The iGAGING® AngleCube
®
is a precision instrument used for measuring angles in which any
of its our surfaces may be utilized.
• Zero can be set at any angle so that the relative angle between two surfaces can be measured.
• The AngleCube
®
can also measure absolute level, yuu can utilize it as a portable pocket level.
Operation
1. To power on and read absolute level, push the " /...LEVEL" button; "LEVEL" will
appear on the upper-left corner of the display.
2. To measure relative bevel, place the AngleCube
®on a table surface and push the
"ZERO" button. Then move the AngleCube
®to the second surface, the gage will
accurately measure and display the bevel angle between the two surfaces.
3. To switch back to absolute level measuring again, push and hold the " /...LEVEL"
button for 3 seconds.
4. To hold the reading, push the "HOLD" button, "H" will display at the upper-center of the
display. To disable the HOLD function, push "HOLD" button again.
5. If " " signal appears on the LCD display, or the gauge will not power on, then it is
time to change the battery. Remove the back plate with the screwdriver supplied
and insert a new standard 9 volt battery.
6. To power o, push the " /...LEVEL" button. Unit will autmatically shut-o within
3 - 5 minutes when not in use.
AngleCube
® Angle Gauge Item #’s 35-222-6
Please read through this owner’s manual carefully before using the gauge. Use tool properly and only for it’s intended use.
Manufacture supplied information. Information may change without notice. Visit iGAGING.com for more information.
© 2022 iGAGING. San Clemente, California USA
CALIFORNIA PROP 65 WARNING: Products may contain chemicals known to the State of California to cause
cancer and/or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Under normal conditions, AngleCube
®does not need re-calibration. If necessary, under the condition of the reading
became inaccurate, or under the condition of severe impact, the AngleCube
®may be re-calibrated professionally.
Re-calibration requires a calibrated level surface within ≤0.02° accuracy, and may require several attempts to
accomplish accurate calibration. It is important to hold the AngleCube
®steady while pressing the buttons
to re-calibrate. **WARNING: Un-leveled surfaces may result in a inaccurate calibration.**
1. Place the box upright
on a level surface.
** The accuracy of the
granite level surface
must be ≤0.02° in
order to make the
re-calibration eective.**
4. Turn the box 90 degrees
clockwise; press the
ZERO button - the screen
will read CAd2, make
sure the box has no
movement until the
"2" flashes.
6. Turn the box another 90
degrees clockwise; press
the ZERO button - the
screen will read CAd4,
make sure the box has
no movement until the
"4" flashes.
8. Your AngleCube
®is
now ready to use.
5. Turn the box another 90
degrees clockwise; press
the ZERO button - the
screen will read CAd3,
make sure the box has
no movement until the
"3" flashes.
7. Turn the box another 90
degrees clockwise; press
the ZERO button - the
screen will read CAd5.
After 3 seconds the
display will read 0.00 -
this completes
the calibration.
Low
Battery
Warning
2. Press and hold
and ZERO buttons for
5 seconds until the
screen displaya CAd1.
3. Release the buttons
and make sure the box
has no movement until
the "1" flashes.
The AngleCube
®should be setting right side up
The AngleCube
®should be setting on it's top
The AngleCube
®should be setting right side up
AngleCube
®should be setting on the right side
AngleCube
®should be setting on the left side
AngleCube
®
AngleCube
®
AngleCube
®
AngleCube
®
AngleCube
®
AngleCube
®
AngleCube
®
AngleCube
®