IgniteNet Spark IR-AC750 User manual

Quick Star t Guide
Cloud-Enabled Enterprise Access Point
The Spark AC750 are dual AP. The units are designed to be operated either placed
on a desk or mounted on a wall or ceiling. The package includes a mounting plate
or attaching the AP to a wall or ceiling T-bar. The APs can be powered either by the
universal power supply included in the package, through an Ethernet cable
connection rom a Power-over-Ethernet (PoE) injector, or rom a 802.3a -compliant
PoE switch.
The Cloud-Enabled Enterprise Access Point includes these models:
 IR-AC750 & IR-AC750-EU — dual-band concurrent enterprise AP with
integrated antennas plus passive Power-over-Ethernet (PoE)
Note: For Sa ety and Regulatory in ormation, re er to the Sa ety and Regulatory
In ormation document included with the AP.
www.ignitenet.com
– 1 –

Quick
Start
Guide
–
2
–
Follow the steps in this guide to install the AP in your network.
Caution: The planning and installation o the AP requires pro essional personnel
that are trained in the installation o radio transmitting equipment. The user is
responsible or compliance with local regulations concerning items such as antenna
power or instance. There ore, it is recommended to consult a pro essional
contractor knowledgeable in local radio regulations prior to equipment installation.
1.Unpack the AP Unpack the AP and check the package contents.
 Cloud-Enabled Enterprise Access Point Spark
AC750
 Mounting plate
 Mounting kit — 4 screws, 4 wall plugs, and 4 rubber eet
 Universal AC/DC power adapter
 Documentation —Quick Start Guide and Regulatory and Safety Information
2.Mount the AP Using the AP on a desktop
I the AP is not mounted on a wall or on the ceiling, place the provided rubber eet
on the AP.
Desktop Mounting
1 1
Place the provided rubber eet over
1 the our screw holes.
1 1

Quick
Start
Guide
–
3
–
Mounting the AP on a wall
Mount the unit on a wall using the mounting plate, screws, and wall plugs provided
in the mounting kit.
Wall Mounting
At the installation location, hold the mounting
plate against the wall with its release tab pointing
down.
Mark the our holes or the wall plugs and screws.
Drill our holes or the wall plugs, and then insert
the plugs and tap them lush with the wall sur ace.
Align the mounting plate with the our holes, and
then use the our screws to secure it to the wall.
With its ports acing down, place the AP against
the wall above the mounting plate.
Slide the rails on the back o the AP down onto the
mounting plate until it snaps into its secured
position. Do not let go o the AP until you con irm
that it is secure.
2
1
1
2

Quick
Start
Guide
–
4
–
Mounting the AP on the ceiling
I the room is equipped with a suspended ceiling, use the mounting plate provided in
the package to attach the AP to the metal ceiling T-bars.
The mounting plate supports two di erent sizes o suspended ceiling T-bars. The
position illustrated below is or 15 mm bars. Use the position at a 90 degrees angle
or 24.5 mm bars.
Suspended Ceiling Mounting
Press the retention clips o the mounting plate
against the ceiling T-bar.
Rotate the plate until the T-bar snaps into place.
Slide the rails on the back o the AP along the
sides o the ceiling mounting plate until it snaps
into its secured position.
3
1
2
1
2
1
2
3

Quick
Start
Guide
–
5
–
3.Connect Cables Connect Ethernet cable to the 1000BASE-T (WAN PoE) port on the unit.
Connect Category 5e or better cable to the
WAN PoE RJ-45 port.
Connect the other end o this cable to a
PoE injector or LAN PoE switch (depending
on AP model).
(Optional) Connect local LAN devices to
any o the other RJ-45 ports on the AP
using Category 5 or better cable.
These 100BASE-TX ports are labeled LAN1
and LAN2.
4.Connect Power The AP can be powered either by the AC/DC power adapter provided in the package,
by a PoE power injector (Spark AC750)
Powering the AP with the AC DC Power Adapter
Connect the cable rom the power adapter
to the DC power jack on the AP.
Connect the power adapter to a nearby AC
power source (100-240 VAC, 50/60 Hz).
Powering the AP with a PoE Injector or PoE Switch
Connect Ethernet cable rom the WAN PoE port o the AP to a port on the PoE
power source device:
 Spark AC750 — a PoE power injector (passive PoE, 24-48 VDC).
switch. Make sure that the PoE power injector or switch is connected to the
LAN.
Note: Connecting the Ethernet cable rom the AP to a PoE injector or PoE switch
powers on the unit.
2
1
1
2
1
1

Quick
Start
Guide
–
6
–
5.Verify AP Operation Veri y basic AP operation by checking the system LEDs.
The WAN PoE port link/activity LED
should be on/blinking green.
When connected, the LAN1 and
LAN2 port link/activity LEDs
should also be on/blinking green.
The system/wireless LED should be
on red when the AP is powered on,
or on/blinking green (2.4 GHz) or
blue (5 GHz).
6.Connect to the Web
User Interface
When managed in a stand-alone mode, the AP o ers a web-based management
inter ace or the con iguration o all the unit’s eatures. I cloud-managing the AP,
go directly to “Manage the AP with the IgniteNet Cloud Controller” on page 7.
To access the web inter ace, connect a PC directly to the AP’s LAN1 or LAN2 RJ-45
port. You must irst set your PC IP address to be on the same subnet as the AP (that
is, the PC and AP addresses must both start 192.168.2.x with a subnet mask o
255.255.255.0). In a web browser, enter the AP’s de ault management IP address o
192.168.2.1 to access the web login page.
Log in to the web inter ace using the
de ault settings:
 Login Name — root
 Password — admin123
Note: To reset the AP to actory de ault settings, press and hold down the AP’s
Reset button or 5 seconds.
1
2
1
2

Quick
Start
Guide
–
7
–
7.Complete the Setup
Wizard
The irst time you log in to the web inter ace, the Setup Wizard is displayed.
Select the country o operation or the AP. Setting the correct country ensures that
the radios operate within local regulations speci ied or Wi-Fi networks.
Manage the AP with the IgniteNet Cloud Controller
Go to cloud.ignitenet.com to register your AP.
Log in and select Devices rom the menu. Click Add Device and enter the AP serial
number and MAC address to register the AP with your cloud network. The serial
number and MAC address can be ound on the product packaging or label.
Manage the AP in Stand-Alone Mode
I you select to manage the AP in stand-alone mode, complete the “Easy” or
“Advanced” setup in the wizard.
For more in ormation on AP con iguration in stand-alone mode, re er to the User
Guide.

Quick
Start
Guide
Hardware Specifications
Chassis
Size (L x W x H:) 121 x 121 x 30.5 mm (4.76 x 4.76 x 1.2 inches)
Weight 196 g (0.43 lb)
Temperature Operating: -20 °C to 65 °C
Humidity Operating: 10% to 90% (non-condensing)
Network Interfaces
Ports WAN PoE RJ-45 Port: 1000BASE-T, passive PoE
LAN1 RJ-45 Port: 100BASE-TX
LAN2 RJ-45 Port: 100BASE-TX
2.4 GHz Radio IEEE 802.11b/g/n
5 GHz Radio IEEE 802.11a/n/ac
Radio Frequencies 2412 ~ 2462 MHz
5180 ~ 5240 MHz
5745 ~ 5825 MHz
Power Supply
AC Power Adapter Input: 100-240 VAC, 50-60 Hz, auto-sensing
Output: 12, 24 VDC, 1.5 A maximum @ 12 VDC
Passive PoE Input Power 24 VDC, 0.7 A maximum @ 24 VDC
Regulatory Compliances
Radio EN 300 328 V1.8.1:2012
EN 301 893 V1.7.1:2012
EN 301 489-1 V1.9.2 (2011-09)
EN 301 489-7 V1.3.1:2005
FCC Part 15C 15.247/15.207
FCC Part 15E 15.407
Emissions EN 55022 2010+AC:2011
EN 61000-3-2 2006+A1:2009+A2:2009
FCC Class B Part 15
Immunity EN 55024 : 2010
EN 61000-4-2 : 2009
– 8 –
Spark AC750
E052015-CS 150200001184A R01
Item Specification

Quick
Start
Guide
Federal Communication Commission Interference
Statement
This device complies with Part 15 o the FCC Rules. Operation
is subject to the ollowing two conditions: (1) This device may
not cause harm ul inter erence, and (2) this device must
accept any inter erence received, including inter erence that
may cause undesired operation.
This equipment has been tested and ound to comply with the
limits or a Class B digital device, pursuant to Part 15 o the
FCC Rules. These limits are designed to provide reasonable
protection against harm ul inter erence in a residential
installation. This equipment generates, uses and can radiate
radio requency energy and, i not installed and used in
accordance with the instructions, may cause harm ul
inter erence to radio communications. However, there is no
guarantee that inter erence will not occur in a particular
installation. I this equipment does cause harm ul inter erence
to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to
try to correct the inter erence by one o the ollowing
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
di erent rom that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician or help.
FCC Caution: Any changes or modi ications not expressly
approved by the party responsible or compliance could void
the user's authority to operate this equipment.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.

Quick
Start
Guide
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits
set orth or an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm
between the radiator & your body.
Note: The country code selection is or non-US model only and
is not available to all US model. Per FCC regulation, all WiFi
product marketed in US must ixed to US operation channels
only.
Professional installation instruction
1. Installation personal
This product is designed or speci ic application and needs to
be installed by a quali ied personal who has RF and related
rule knowledge. The general user shall not attempt to install or
change the setting.
2. Installation location
The product shall be installed at a location where the radiating
antenna can be kept 20cm rom nearby person in normal
operation condition to meet regulatory RF exposure
requirement.
3. External antenna
Use only the antennas which have been approved by the
applicant. The non-approved antenna(s) may produce
unwanted spurious or excessive RF transmitting power which
may lead to the violation o FCC limit and is prohibited.
4. Installation procedure
Please re er to user’s manual or the detail.
5. Warning
Please care ully select the installation position and make sure
that the inal output power does not exceed the limit set orce
in relevant rules. The violation o the rule could lead to serious
ederal penalty.