Ignition Strip Blinder UV 5x4W User manual

Strip Blinder
U S E R M A N U A L
Strip Blinder
UV 5x4W
UV 5x4W

1. SAFETY INSTRUCTION
................................
1.1.
FOR SAFE INSTALLATION AND EFFICIENT OPERATION
1.1.1.
Use of the item as intended
1.1.2. Overhead rigging
1.1.3.
Cleaning and Maintenance
2. Introduction
................................
3. OPERATION MODES
................................
3.1. DMX MODE
................................
3.1.1. DMX chart
................................
3.1.2.
Selecting DMX Mode
3.1.3.
Selecting Channel Mode
3.1.4. Selecting DMX A
ddress Mode
3.2. CHASE MODE
................................
3.2.1.
Selecting the Program
3.2.2.
Selecting Chase Speed
3.2.3. Dimmer
................................
3.2.4.
Display on and off
3.2.5. Auto
................................
3.2.6. Full
................................
3.2.7. Sound
................................
3.3. Slave mode
................................
4. Technical Data
................................
2 / 10
S T R I P B L I N D E R U V 5 X 4
Table of contents
................................
................................
................................
FOR SAFE INSTALLATION AND EFFICIENT OPERATION
................................
Use of the item as intended
................................
................................
................................................................
................................
Cleaning and Maintenance
................................
................................
................................
................................................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
Selecting DMX Mode
................................................................
................................
Selecting Channel Mode
................................................................
................................
ddress Mode
................................
................................
................................
................................
................................
Selecting the Program
................................................................
................................
Selecting Chase Speed
................................................................
................................
................................
................................
................................
Display on and off
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
................................
................................
................................
................................
................................
................................
................................
................................................................
................................
S T R I P B L I N D E R U V 5 X 4
W
................................
.................. 3
................................
................. 3
................................
............................. 3
................................
............. 4
................................
.............................. 5
................................
....... 5
................................
...................... 6
................................
............................. 6
................................
........................ 6
................................
....... 6
................................
. 7
................................
......................... 7
................................
......................... 7
................................
..... 7
................................
... 7
................................
............................ 8
................................
............ 8
................................
. 8
................................
... 8
................................
.............................. 8
................................
.............................. 9
................................
. 9

The manual contains complete information about the item and how to
once again make sure to that you read the operation instruction and safety information before using
the device. Throughout the manual the following conventions are used distinguishing the elements of
text:
S CAUTION: Identif
ies important information which should be followed to avoid damage of device
S
NOTE: Provides additional hints or information that requires special attention.
Menu names, command, icon or button that you can see is shown in bold style.
1.
SAFETY INSTRUCTI
A
NOTICE
All modifications to the device
to carry out by skilled personnel only.
A
CAUTION
Avoid looking directly into the source of light.
touching the item when ON, the housing can reach a high temperature from the
heat developed by the high power LED.
1.1.
FOR SAFE INSTALLATION AND EFFICIENT OPERATION
1.1.1.
Use of the item as intended
•The Strip Blinder X
is
illumination.
The device is approved only for a connection up to a maximum of
50/60Hz.
•
The ambient temperature must be between
device to direct rays of the sun or next to a heating appliance. This also applies for
transportation in closed vehicles.
•
The device may only be operated at a level between
•The symbol
stands for the min distance between the item and obj
between light source and surface should not be less than
cm
space around the item for good ventilation.
•
Regular stoppages increase the life of your device
•
Avoid shakes and every form of violence during
•
Make sure that the device is not exposed to extreme heat, humidity or dust at the installation
spot. Make sure that cables do not lie around. This would decrease your own safety and the
safety of third parties.
•Do not operate the
device during thunderstorms. Overvoltage could destroy the device.
Disconnect the device during thunderstorms completely from the grid by pulling the mains
plug.
3 / 10
S T R I P B L I N D E R U V 5 X 4
The manual contains complete information about the item and how to
operate with the device. Please
once again make sure to that you read the operation instruction and safety information before using
the device. Throughout the manual the following conventions are used distinguishing the elements of
ies important information which should be followed to avoid damage of device
NOTE: Provides additional hints or information that requires special attention.
Menu names, command, icon or button that you can see is shown in bold style.
SAFETY INSTRUCTI
ON
All modifications to the device
will void the warranty and installation and r
to carry out by skilled personnel only.
Avoid looking directly into the source of light.
It may cause epileptic seizures. Avoid
touching the item when ON, the housing can reach a high temperature from the
heat developed by the high power LED.
FOR SAFE INSTALLATION AND EFFICIENT OPERATION
Use of the item as intended
is
designed for use
on stages, in discotheques and for architectural
The device is approved only for a connection up to a maximum of
The ambient temperature must be between
32°F /0°C and
104°F /40°C
device to direct rays of the sun or next to a heating appliance. This also applies for
transportation in closed vehicles.
The device may only be operated at a level between
-20 and 2000m NN.
stands for the min distance between the item and obj
between light source and surface should not be less than
1.5 m
. Make sure that there is
space around the item for good ventilation.
Regular stoppages increase the life of your device
.
Avoid shakes and every form of violence during
the installation or usage.
Make sure that the device is not exposed to extreme heat, humidity or dust at the installation
spot. Make sure that cables do not lie around. This would decrease your own safety and the
device during thunderstorms. Overvoltage could destroy the device.
Disconnect the device during thunderstorms completely from the grid by pulling the mains
S T R I P B L I N D E R U V 5 X 4
W
operate with the device. Please
once again make sure to that you read the operation instruction and safety information before using
the device. Throughout the manual the following conventions are used distinguishing the elements of
ies important information which should be followed to avoid damage of device
will void the warranty and installation and r
epairs are
It may cause epileptic seizures. Avoid
touching the item when ON, the housing can reach a high temperature from the
on stages, in discotheques and for architectural
The device is approved only for a connection up to a maximum of
AC 100-240V,
104°F /40°C
. Avoid exposing the
device to direct rays of the sun or next to a heating appliance. This also applies for
stands for the min distance between the item and obj
ects. The distance
. Make sure that there is
50
Make sure that the device is not exposed to extreme heat, humidity or dust at the installation
spot. Make sure that cables do not lie around. This would decrease your own safety and the
device during thunderstorms. Overvoltage could destroy the device.
Disconnect the device during thunderstorms completely from the grid by pulling the mains

•
Avoid looking directly into the source of light. It may cause epileptic seizures. This appl
particular for people where epileptic seizure has been diagnosed by a doctor
•Power cable, n
ever pull the power cable to remove the plug from the receptacle,
hold the plug. When not using the device for an extended period of time, be sure to disconnect
the plug from the receptacle.
•
Make sure that the area under the item is blocked, while mounting it or working on it.
•
When cleaning, use a clean dry clot
A NOTE After
taking the device from a warm to a cold room, it may not be put into operation.
The resulting condensation can possibly destroy the device. Do not turn on the device
until it ha
s reached ambient temperature.
A NOTE
Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept liability for any resulting defects or problems.
electrical connection is carried out
connections have to be carried out according to the European safety standards.
This device falls under the protection class I. It is necessary to follow the instructions.
1.1.2.
Overhead rigging
The suspension
devices have to be build and measured so they can withstand for an hour the tenfold
of the payload without suffering a permanent detrimental deformation
made by using a second separate suspension. This can be e.g. a suitab
suspension must be designed and attached so no part of the installation can fall down in case of
failure.
The maximum drop distance must never exceed
During construction, reconstruction and deconstruction unnecessary stay in the
areas, on lightning bridges, under elevated work stations or any other danger zones is forbidden
Before taking the device in operation, the installation must be approved by an expert. The operator
obliged to get an expert to check safet
A NOTE
Overhead installation requires a high level of experience. This includes knowledge of
calculating the payload, used installation material and safety inspections of the used
installation mat
erial and the projector whereas the required experience is not limited to
this. Do not try to carry out installation yourself under any circumstances if you are not
qualified. Contact a professional installer. An inappropriate installation can lead to
inju
ries and/or damaged properties.
If the projector may hang from the ceiling or from high beams, the use of truss systems is mandatory.
The projector may not be installed
4 / 10
S T R I P B L I N D E R U V 5 X 4
Avoid looking directly into the source of light. It may cause epileptic seizures. This appl
particular for people where epileptic seizure has been diagnosed by a doctor
ever pull the power cable to remove the plug from the receptacle,
hold the plug. When not using the device for an extended period of time, be sure to disconnect
the plug from the receptacle.
Make sure that the area under the item is blocked, while mounting it or working on it.
When cleaning, use a clean dry clot
h to wipe off the dust, or a wet soft cloth for stubborn dirt.
taking the device from a warm to a cold room, it may not be put into operation.
The resulting condensation can possibly destroy the device. Do not turn on the device
s reached ambient temperature.
Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept liability for any resulting defects or problems.
electrical connection is carried out
by qualified personnel
. All electrical and mechanical
connections have to be carried out according to the European safety standards.
This device falls under the protection class I. It is necessary to follow the instructions.
Overhead rigging
devices have to be build and measured so they can withstand for an hour the tenfold
of the payload without suffering a permanent detrimental deformation
.
Basically installation has to be
made by using a second separate suspension. This can be e.g. a suitab
suspension must be designed and attached so no part of the installation can fall down in case of
The maximum drop distance must never exceed
20 cm.
During construction, reconstruction and deconstruction unnecessary stay in the
areas, on lightning bridges, under elevated work stations or any other danger zones is forbidden
Before taking the device in operation, the installation must be approved by an expert. The operator
obliged to get an expert to check safet
y-
related and mechanical facilities at least once a year
Overhead installation requires a high level of experience. This includes knowledge of
calculating the payload, used installation material and safety inspections of the used
erial and the projector whereas the required experience is not limited to
this. Do not try to carry out installation yourself under any circumstances if you are not
qualified. Contact a professional installer. An inappropriate installation can lead to
ries and/or damaged properties.
If the projector may hang from the ceiling or from high beams, the use of truss systems is mandatory.
The projector may not be installed
so it can swing freely in the room.
S T R I P B L I N D E R U V 5 X 4
W
Avoid looking directly into the source of light. It may cause epileptic seizures. This appl
ies in
particular for people where epileptic seizure has been diagnosed by a doctor
.
ever pull the power cable to remove the plug from the receptacle,
is sure to
hold the plug. When not using the device for an extended period of time, be sure to disconnect
Make sure that the area under the item is blocked, while mounting it or working on it.
h to wipe off the dust, or a wet soft cloth for stubborn dirt.
taking the device from a warm to a cold room, it may not be put into operation.
The resulting condensation can possibly destroy the device. Do not turn on the device
Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept liability for any resulting defects or problems.
Make sure the
. All electrical and mechanical
connections have to be carried out according to the European safety standards.
This device falls under the protection class I. It is necessary to follow the instructions.
devices have to be build and measured so they can withstand for an hour the tenfold
Basically installation has to be
made by using a second separate suspension. This can be e.g. a suitab
le net. The second
suspension must be designed and attached so no part of the installation can fall down in case of
During construction, reconstruction and deconstruction unnecessary stay in the
range of moving
areas, on lightning bridges, under elevated work stations or any other danger zones is forbidden
.
Before taking the device in operation, the installation must be approved by an expert. The operator
is
related and mechanical facilities at least once a year
.
Overhead installation requires a high level of experience. This includes knowledge of
calculating the payload, used installation material and safety inspections of the used
erial and the projector whereas the required experience is not limited to
this. Do not try to carry out installation yourself under any circumstances if you are not
qualified. Contact a professional installer. An inappropriate installation can lead to
If the projector may hang from the ceiling or from high beams, the use of truss systems is mandatory.

A CAUTION Crashing down
items
doubt the safety of a possible installation form
A CAUTION When rigging
the device, make sure there is no highly
(decoration articles, etc.) within a distance of min.
Mount the projector with the mounting
During overhead installation the projector must be always secured by a safety rope which is designed
to hold the twelvefold weight of the device
elements may be used.
Hang up the safety rope in the hole of the mounting bracket. Direct the rope
over the truss or an appropriate fastening point
the locking nut.
A safety rope once exposed to falling load or damaged may not be used furthermore
Adjust the desired inclination angle via the mounting
1.1.3.
Cleaning and Maintenance
Contaminations like dust should be removed
not use alcohol or solvents under any circumstances
mechanical facilities
are inspected by a skilled person once a year.
•
Ensure all screws attached to the
corroded.
•Make sure
there are no deformations of the housing, attachment and installation spot.
This also includes the ceiling, the suspension and the truss
•
Electrical connection cables may not have an
fatigue e.g. porous connections
Important:
Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will not accept liability for any resulting defects or problems.
Make sure the
electrical connection is carried out
and mechanical connections have to be carried out according to the European safety
standards.
2. Introduction
Congratulations to your purchase and thank you for selecting one of our products.
The Strip Blinder UV
is a powerful silent lighting device. For successful installation and secure
operation and secure please read the user manual before starting operating
5 / 10
S T R I P B L I N D E R U V 5 X 4
items
can cause serious injuries! Do not
install the projector, if you
doubt the safety of a possible installation form
!
the device, make sure there is no highly
-
inflammable material
(decoration articles, etc.) within a distance of min.
1.5 m.
Mount the projector with the mounting
-
bracket to your trussing system using an appropriate clamp.
During overhead installation the projector must be always secured by a safety rope which is designed
to hold the twelvefold weight of the device
. Only safety ropes with quick-
release safety fastener
Hang up the safety rope in the hole of the mounting bracket. Direct the rope
over the truss or an appropriate fastening point
.
Hang up the end in the fastening element and tie up
A safety rope once exposed to falling load or damaged may not be used furthermore
Adjust the desired inclination angle via the mounting
-
bracket and tighten the screw.
Cleaning and Maintenance
Contaminations like dust should be removed
regularly from the device. Use a damp, lint free, cloth. Do
not use alcohol or solvents under any circumstances
. Please make sure that
safety
are inspected by a skilled person once a year.
Ensure all screws attached to the
device or parts of the device are very tight and not
there are no deformations of the housing, attachment and installation spot.
This also includes the ceiling, the suspension and the truss
.
Electrical connection cables may not have an
y damages, depositions or signs of material
fatigue e.g. porous connections
.
Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will not accept liability for any resulting defects or problems.
electrical connection is carried out
by qualified personnel
and mechanical connections have to be carried out according to the European safety
Congratulations to your purchase and thank you for selecting one of our products.
is a powerful silent lighting device. For successful installation and secure
operation and secure please read the user manual before starting operating
with the device.
S T R I P B L I N D E R U V 5 X 4
W
install the projector, if you
inflammable material
bracket to your trussing system using an appropriate clamp.
During overhead installation the projector must be always secured by a safety rope which is designed
release safety fastener
Hang up the safety rope in the hole of the mounting bracket. Direct the rope
Hang up the end in the fastening element and tie up
A safety rope once exposed to falling load or damaged may not be used furthermore
.
bracket and tighten the screw.
regularly from the device. Use a damp, lint free, cloth. Do
safety
-related and
device or parts of the device are very tight and not
there are no deformations of the housing, attachment and installation spot.
y damages, depositions or signs of material
Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will not accept liability for any resulting defects or problems.
by qualified personnel
. All electrical
and mechanical connections have to be carried out according to the European safety
Congratulations to your purchase and thank you for selecting one of our products.
is a powerful silent lighting device. For successful installation and secure
with the device.

3.
OPERATION MODES
The
device operates in three operating modes, DMX Mode, Program Mode and Master Slave.
3.1.DMX MODE
DMX Modes with 3 channels.
The go into the DMX Mode please push Mode until you see A001, SLAV or CHx. Then push Menu
until you see A001.
3.1.1. DMX chart
Channel Value
Function
1 0-255
Master dimmer 0
2 0-255
Program speed 0
3
<10 OFF
10-39
Program 1
40-59
Program 2
60-79
Program 3
80-99
Program 4
100-119
Program 5
120-139
Program 6
140-159
Program 7
160-179
Sound mode
179 FULL
3.1.2.
Selecting DMX Mode
001
Mode
Menu
6 / 10
S T R I P B L I N D E R U V 5 X 4
OPERATION MODES
device operates in three operating modes, DMX Mode, Program Mode and Master Slave.
The go into the DMX Mode please push Mode until you see A001, SLAV or CHx. Then push Menu
Function
Master dimmer 0
-100%
Program speed 0
-100
Program 1
Program 2
Program 3
Program 4
Program 5
Program 6
Program 7
Sound mode
Selecting DMX Mode
If letter "A" appears, means that DMX address and shows that the
DMX Mode has been activated. Letter "P" means that y
Chase Mode. With
“Mode” button can you change between the two
modes.
S T R I P B L I N D E R U V 5 X 4
W
device operates in three operating modes, DMX Mode, Program Mode and Master Slave.
The go into the DMX Mode please push Mode until you see A001, SLAV or CHx. Then push Menu
If letter "A" appears, means that DMX address and shows that the
DMX Mode has been activated. Letter "P" means that y
ou are in the
“Mode” button can you change between the two

3.1.3. Selecting
Channel Mode
3.1.4.
Selecting DMX Address Mode
3.2.CHASE MODE
The unit has 7
built in programs (except Auto and Full). Creating a light show you can select any of the
build-
in programs and also can control the speed which the program will be chasing.
3.2.1.
Selecting the Program
3.2.2.
Selecting Chase Speed
SP:01
Mode
Menu
P:01
Mode
Menu
A:001
A
Mode
Menu
CH:01
Mode
Menu
7 / 10
S T R I P B L I N D E R U V 5 X 4
Channel Mode
Tap “Menu” button to select to Channel Mode. When letters "CH"
followed by 2 numbers (03
) than you are on the Channel Mode.
Channel Value Selection: Tap “Up ” or “Down
channel.
“CH03: Channel 1, 2, 3 will be controlled by one DMX.
Selecting DMX Address Mode
Tap “Menu” button, “
A “ appears on the display following by three
numbers 001 to 512, it indicates the DMX Mode is activated.
DMX address: Tap “Up ” or “Down
” to select between the 001
and 512 DMX-address.
built in programs (except Auto and Full). Creating a light show you can select any of the
in programs and also can control the speed which the program will be chasing.
Selecting the Program
Tap the “Mode” button, "P" is shown it indicates that Chase Mode is
activated.
Selecting Program: Tap “Up ” or “Down
” you can enter
program 01 to 07 and Auto and Full.
Selecting Chase Speed
Tap “Menu” button, "SP:01" appears on the display, it indicates for
Chase Speed Mode.
Selecting Speed: Tap “Up ” or “Down
” you can regulate the
speed between lowest speed 01 and fastest speed 99.
S T R I P B L I N D E R U V 5 X 4
W
Tap “Menu” button to select to Channel Mode. When letters "CH"
) than you are on the Channel Mode.
” to select 03
“CH03: Channel 1, 2, 3 will be controlled by one DMX.
A “ appears on the display following by three
numbers 001 to 512, it indicates the DMX Mode is activated.
” to select between the 001
built in programs (except Auto and Full). Creating a light show you can select any of the
in programs and also can control the speed which the program will be chasing.
Tap the “Mode” button, "P" is shown it indicates that Chase Mode is
” you can enter
Tap “Menu” button, "SP:01" appears on the display, it indicates for
” you can regulate the
speed between lowest speed 01 and fastest speed 99.

d:000
Mode
Menu
AUTO
Mode
Menu
ds
-
n
Mode
Menu
3.2.3. Dimmer
3.2.4.
Display on and off
3.2.5. Auto
3.2.6. Full
3.2.7. Sound
sound
Mode
Menu
FULL
Mode
Menu
8 / 10
S T R I P B L I N D E R U V 5 X 4
Tap
“Menu” button, "d:000" appears on the display, indication that
you have entered Chase Dimmer Mode.
Regulate the Intensity: Tap “Up ” or “Down
” to regulate the
intensity between 000 (Off) to 100 (highest output).
Display on and off
Tap “Menu” button, "ds-n/F
" appears on the display, indication that
you have entered Chase display setup.
Display options: Tap “Up ” or “Down ” to
set the
“f” close.
The device will play all programs.
All lights will light up and stay on highest output, 100 %.
The device will play run sound mode.
S T R I P B L I N D E R U V 5 X 4
W
“Menu” button, "d:000" appears on the display, indication that
” to regulate the
intensity between 000 (Off) to 100 (highest output).
" appears on the display, indication that
set the
display “n” open,
All lights will light up and stay on highest output, 100 %.

3.3.Slave mode
The Slave mode can be activated by tabbing Mode until you see SLAV in the display. Now the unit
reacts as slave and listens to the master, which is automatically set for
You can use Programs to set up the master slave co
4. Technical Data
LED
Lifetime
Ambient temperature
Cooling
Control DMX
Protection class
Power
Voltage
Measures
Weight
9 / 10
S T R I P B L I N D E R U V 5 X 4
The Slave mode can be activated by tabbing Mode until you see SLAV in the display. Now the unit
reacts as slave and listens to the master, which is automatically set for
every unit which is no slave.
You can use Programs to set up the master slave co
nnection.
5x4W UV LEDs
>20000h
0°C -40°C
Convection cooled
3 channels
IP20
max. 30W
AC 100-240V, 50/60Hz
576mm x 130mm x 139.5mm
3,3kg
S T R I P B L I N D E R U V 5 X 4
W
The Slave mode can be activated by tabbing Mode until you see SLAV in the display. Now the unit
every unit which is no slave.

10 / 10
S T R I P B L I N D E R U V 5 X 4
Importer:
B&K Braun GmbH
Industriestraße 2
D-76307 Karlsbad-Ittersbach
www.bkbraun.com
[email protected]
S T R I P B L I N D E R U V 5 X 4
W