Iiyama ProLite TH4264MIS User manual

ENGLISH
Thank you very much for choosing the iiyama
LCD monitor.
We recommend that you take a few minutes
to read this comprehensive manual carefully
before installing and switching on the monitor.
Please keep this manual in a safe place for
your future reference.
USER MANUAL

ENGLISH
We reserve the right to change specifications without notice.
All trademarks used in this user manual are the property of their respective owners.
We recommend recycling of used product. Please contact your dealer or iiyama
service center. Recycle information is obtained via the Internet, using the
address: http://www.iiyama.com
You can access the Web page of different countries from there.
CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EC/EU Directive 2004/108/EC “EMC
Directive”, 2006/95/EC “Low Voltage Directive” and 2011/65/EU “RoHS Directive”.
Warning
This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
IIYAMA CORPORATION: Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands

ENGLISH
TABLE OF CONTENTS
FOR YOUR SAFETY............................................................................1
SAFETY PRECAUTIONS................................................................1
SPECIAL NOTES ON LCD MONITORS.........................................3
CUSTOMER SERVICE...................................................................4
CLEANING......................................................................................4
BEFORE YOU OPERATE THE MONITOR..........................................5
FEATURES......................................................................................5
CHECKING THE CONTENTS OF THE PACKAGE........................5
UNPACKING ...................................................................................6
SPECIAL NOTES ON : ProLite TH4264MIS...................................6
CONTROLS AND CONNECTORS : MONITOR..............................7
INSTALLATION ...............................................................................9
CONTROLS AND CONNECTORS : REMOTE CONTROL...........11
PREPARING THE REMOTE CONTROL.......................................12
BASIC OPERATION......................................................................13
CONNECTING YOUR MONITOR.................................................16
COMPUTER SETTING.................................................................18
OPERATING THE MONITOR.............................................................20
ADJUSTMENT MENU CONTENTS..............................................22
SCREEN ADJUSTMENTS............................................................30
POWER MANAGEMENT FEATURE.............................................33
TROUBLE SHOOTING ......................................................................34
RECYCLING INFORMATION.............................................................35
APPENDIX ........................................................................................36
SPECIFICATIONS :
ProLite TH4264MIS-B1 / ProLite TH4264MIS-B1AG....................36
SPECIFICATIONS :
ProLite TH4264MIS-B2 / ProLite TH4264MIS-B2AG....................37
SPECIFICATIONS : ProLite LH4264S ..........................................38
DIMENSIONS :
ProLite TH4264MIS-B1 / ProLite TH4264MIS-B1AG....................39
DIMENSIONS :
ProLite TH4264MIS-B2 / ProLite TH4264MIS-B2AG....................39
DIMENSIONS : ProLite LH4264S.................................................40
COMPLIANT TIMING....................................................................41
PAP SUPPORT SCREEN TABLE.................................................42

ENGLISH
FOR YOUR SAFETY 1
FOR YOUR SAFETY
WARNING
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the
monitor and contact your dealer or iiyama service center immediately. Further use may be
dangerous and can cause fire or electric shock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of
fire or electric shock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with
any object inside may cause fire, electric shock or damage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric
shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will
cause malfunction and may cause fire or electric shock.
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objects on the cables. If damaged, the cables may cause fire or electric shock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it
may cause electric shock.
SAFETY PRECAUTIONS

ENGLISH
2 FOR YOUR SAFETY
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or
smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the
sun shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
place any heavy objects on the monitor, and that all cables are routed such that children may not
pull the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause
fire. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls.
Do not remove the tilt stand when operating the monitor. Ventilation slots on the back of the
cabinet will be blocked and the monitor may overheat if the stand is removed. This may cause fire
or damage. Operating the monitor on its back, side, upside down or on a carpet or any other soft
material may also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal
cable is disconnected. If you do not disconnect them, it may cause fire or electric shock.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to
avoid accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable
itself as this may cause fire or electric shock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may
damage your computer.
REMARK FOR 24/7 USAGE
This product is not specifically designed for 24/7 usage in all environments.
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room.
For optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches)
away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour
is recommended as looking at the screen continuously can cause eye strain.
OTHERS

ENGLISH
FOR YOUR SAFETY 3
The following symptoms are normal with LCD monitors and do not indicate a problem.
NOTE 
When you first turn on the LCD monitor, the picture may not fit in the display area
because of the type of computer that is used. In this case, adjust the picture position
to the correct position.

You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.

Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours. In
this case, the screen is recovered slowly by changing the image or turning off the
Power Switch for hours.

Max. non-stop operating time and conditions
(1) If a static image is displayed continuously, it is recommended to disrupt it with a
motion picture.
(2) It is recommended to periodically change the background colour and background
image.
(3) Maximum operating time of the display is 18 hours per day, if the IRFM function is
set on. If the IRFM function is off, do not exceed a 12 hour non-stop operating time
limit.
(4) If the screen is active for a longer period of time, it is recommended to
I. Run the screensaver (motion picture or black pattern)
II. Power off the system for a while
(5) Make sure that the screen is suitably ventilated, or is used in conjunction with
climate control system if installed into any bespoke cabinets.
(6) We strongly recommend an active cooling system with fans for long operating times,
especially for high luminance LCD models.

This LCD cannot be used outdoors.

This LCD cannot be used with the screen facing upwards.

If you use a cable longer than the supplied one, the picture quality is not guaranteed.
Touch function can be disrupted if the USB cable length exceeds 3m.
SPECIAL NOTES ON LCD MONITORS

ENGLISH
4 FOR YOUR SAFETY
NOTE 
If you have to return your unit for service and the original packaging has been
discarded, please contact your dealer or iiyama service center for advice or
replacement packaging.
WARNING 
If you drop any materials or liquids such as water into the monitor when cleaning,
unplug the power cable immediately and contact your dealer or iiyama service center.
CAUTION 
For safety reasons, turn off the power switch and unplug the monitor before you
clean it.
NOTE 
To protect the LCD panel, do not scratch or rub the screen with a hard object.

Never use any of the following strong solvents. These will damage the cabinet and
the LCD screen.

Touching the cabinet with any product made from rubber or plastic for a long time
may cause degeneration or loss of paint on the cabinet.
Thinner Benzine Abrasive cleaner
Spray-type cleaner Wax Acid or Alkaline solvent
CABINET Stains can be removed with a cloth lightly moistened with a mild detergent solvent.
Then wipe the cabinet with a soft dry cloth.
LCD
SCREEN Periodic cleaning with a soft dry cloth is recommended.
Don't use tissue paper etc. because these will damage the LCD screen.
CUSTOMER SERVICE
CLEANING

ENGLISH
BEFORE YOU OPERATE THE MONITOR 5
The following accessories are included in your package. Check to see if they are enclosed with
the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional
iiyama office.
*1 The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using
a power supply higher than this rating, then a power cable with a rating of 10A/
250V must be used. However, all guarantees and warranties are void for any
problems or damage caused by a power cable not supplied by iiyama.
*2Accessory for ProLite TH4264MIS.
Power Cable*1
VGA(D-sub) Signal Cable DVI-D Signal Cable
USB Cable*2Remote Control Touch Pen*2
iiyama Logo Sticker Safety Guide Quick Start Guide
BEFORE YOU OPERATE THE MONITOR
CHECKING THE CONTENTS OF THE PACKAGE
CAUTION
FEATURES
Supports Resolutions up to 1920 × 1080
High Contrast 1000:1 (Typical: without Touch panel) / Brightness 400cd/m2
(Typical: without Touch panel)
Digital Character Smoothing
Automatic Set-up
Stereo Speakers
2 × 12W Stereo Speakers

Plug & Play VESA DDC2B Compliant
Windows®95/98/2000/Me/XP/Vista/7/8 Compliant
Power Management (VESA DPMS Compliant)
VESA Mounting Standard (400mm×200mm) Compliant

ENGLISH
6 BEFORE YOU OPERATE THE MONITOR
UNPACKING
Before unpacking your monitor, prepare a stable, level, and clean surface near a wall outlet.
Set the LCD Monitor box in an upright position and open from the top of the box before removing
the top cushions.
Remove the carton holders.
Remove the top cushion and take
the accessories box and the Monitor out.
CAUTION
Moving the monitor requires at least two people. If not, it may drop
and could result in a serious injury.
When moving/shipping the monitor, please hold by the carton holders.
SPECIAL NOTES ON : ProLite TH4264MIS
Permanent damage can occur if Sharp Edged, Pointed or Metal items are used to activate Touch.
This could invalidate any remaining warranty.
We recommend you use a plastic stylus (tip R0.8 or over) or finger.
CAUTION
Pinch and Pull the Knob.

ENGLISH
BEFORE YOU OPERATE THE MONITOR 7
CONTROLS AND CONNECTORS : MONITOR
<Back Controller>
ENTER/SOURCE Enter/Input Select Button
MENU Menu Button
Down Button
Up Button
/ - Left / - Button
/ + Right / + Button
Power Button
<Front>
Power Indicator
Green Normal Operation
Red
Flash : Power Management (Power Save : Low)
Lighting : If turn off the Power Button on the Remote
Control and the Back Controller. Power
Management (Power Save : High)
Off Power Off
Remote Sensor Remote Sensor
Ambient Light Sensor Detects ambient lighting conditions around the Monitor and adjusts screen brightness automatically when the
Ambient Light Sensor function is activated.
VIDEO
SOURCE
/ -
/ +

ENGLISH
8 BEFORE YOU OPERATE THE MONITOR
<Back>
* Available for ProLite TH4264MIS only.
<Right Side>
RS232C OUT D-SUB 9pin RS232C Connector
RS232C IN D-SUB 9pin RS232C Connector
COMPONENT
VIDEO (VIDEO IN) RCA G/B/R Component Video Connector
S-Video Mini Din 4pin S-Video Connector
AV OUT BNC Video Connector
AV IN BNC Video Connector
VGA OUT VGA(D-sub) mini 15pin VGA(D-sub) mini 15pin Connector
VGA IN VGA(D-sub) mini 15pin VGA(D-sub) mini 15pin Connector
AUDIO IN1 (PC Audio In) Mini Jack Audio Connector
AUDIO IN2 RCA L/R Audio Connector
AUDIO OUT RCA L/R Audio output Connector
SPEAKERS OUT Jack External Speakers Connector
USB* USB Touch USB Connector
AC SWITCH
(ON) / (OFF) MAIN POWER Main Power Switch
AC IN AC-INLET AC Connector (AC-IN)
AC OUT AC-OUTLET AC Connector (AC-OUT)
SPEAKERS Speakers
RJ45 RJ45 RJ45 Connector
DisplayPort (DP) DisplayPort DisplayPort Connector
HDMI HDMI HDMI Connector
DVI DVI-D 24pin DVI-D 24pin Connector

ENGLISH
BEFORE YOU OPERATE THE MONITOR 9
INSTALLATION
CAUTION
Follow the manual instructions for the type of mount you have selected. Refer all servicing to
qualified service personnel.
Moving the monitor requires at least two people.
Before installing, please make sure the wall is strong enough to hold the necessary weight of the
display and the mount.
[WALL MOUNTING]
When using the wall mounting, consideration of thickness of the mounting stage needs to be taken.
Tighten the M6 Screw with washer which “L” length is 10mm to fasten the monitor. Using a screw
longer than this may cause electric shock or damage because it may contact with the electrical parts
inside the monitor.
CAUTION
L
Mounting Stage Screw
Chassis

ENGLISH
10 BEFORE YOU OPERATE THE MONITOR
[INSTALLATION NOTE] *Available for ProLite TH4264MIS only.
The touch kit of this monitor is an optical device that utilizes infrared light source and sensitive
sensors for touch detection.
Notice the incident light that contains large quantities of infrared light may affect touch screen
operation and performance.
Please install it with care as follows to ensure reliable touch performance.
Intense light / Specular light / Focus spotlight / Wide spread light / Direct sunlight / Indirect sunlight
from the window and/or the glass door. / Not install the touch monitor right under the light source.
Direct
Sunlight
Windows
Light
source
Light source Light source
Front Front
Side Side
[ROTATING THE DISPLAY]
A
A
Not Available
A
A
Landscape
Portrait
Available
It is designed to be compatible in both landscape and portrait modes, however, it is optimized for
landscape mode.

ENGLISH
BEFORE YOU OPERATE THE MONITOR 11
CONTROLS AND CONNECTORS : REMOTE CONTROL
ON/OFF Turns the monitor ON and OFF.
INPUT Selects the source.
Number (1-9) / Input
source
Serve as input source buttons when
the Menu is not displayed.
The HDMI-2, SDI and MULTI-MEDIA
functions are not available with this
monitor.
EXIT Returns to a previous menu or closes
the OSD Menu.
Navigates through submenus and
settings.
: Up Button
: Down Button
: Left Button
: Right Button
(VOLUME-): Decreases the sound
volume.
(VOLUME+): Increases the sound
volume.
ENTER Confirms your selection or save
changes.
INFO Provides source and resolution
information.
MENU
Opens the monitor's on-screen menu
systems. When the menu system is
already open, pressing this button will
select the previous submenu.
Number (0)/ MUTE Turns on or off the mute function
when the Menu is not displayed.
MULTI-MEDIA Not available on this model.

ENGLISH
12 BEFORE YOU OPERATE THE MONITOR
To use the remote control, insert the two dry batteries.
PREPARING THE REMOTE CONTROL
CAUTION
Do not use any other batteries other than those specified in this manual for the Remote Control. Do
not insert old and new batteries together in the Remote Control. Make sure that the terminals match
the "+" and "-" indications in the battery compartment. Burst batteries or the electrolyte from these
batteries may cause stains, fire or injury.
Slide back and remove the battery cover in the direction of the arrow.
Align and insert two AAA batteries according to their plus and minus ports (as indicated in the
remote control).
Replace the battery cover in the direction of the arrow and snap it back into place.
NOTE Replace with new batteries when the Remote Control does not work close to the
monitor. Use AAA dry batteries.
Operate the Remote Control by pointing it toward the Remote Sensor on the monitor.
Other manufacturers remote control will not work with this monitor. Use the provided
Remote Control ONLY.
Used batteries needed to follow the local rules to be discarded. (Suggestion: to dispose
of used batteries please follow correct policy as per your local regulations.)
Battery x 2 (Not included)

ENGLISH
BEFORE YOU OPERATE THE MONITOR 13
BASIC OPERATION
Turning the monitor ON
The monitor is turned On and the Power Indicator turns to Green when you press the POWER
Button on the monitor or the Remote Control. The monitor is turned Off and the Power Indicator
turns to Red when you press the POWER Button on the monitor or the Remote Control.
Press again to turn On the monitor.
NOTE
Even when using the power management mode or turning OFF the Power Switch, the monitor
will consume a small amount of electricity. Disconnect the Power Cable from the power supply
whenever the monitor is not in use or during the night, to avoid unnecessary power consumption.
[Remote Control]
Display the adjustment menu page
The menu page appears on the screen when you press the MENU Button on the monitor or the
Remote Control.
The menu page disappears when you press the EXIT Button on the Remote Control again.
VIDEO
SOURCE
/ -
/ +
[Monitor]
[Remote Control][Monitor]
VIDEO
SOURCE
/ -
/ +

ENGLISH
14 BEFORE YOU OPERATE THE MONITOR
Move the cursor horizontally
Select menu or setting, or perform the adjustment by pressing the / Button while the menu
page is displayed on the screen.
Move the cursor vertically
Select adjustment by pressing the / Button while the menu page is displayed on the screen.
[Remote Control]
[Monitor]
[Remote Control]
[Monitor]
VIDEO
SOURCE
/ -
/ +
VIDEO
SOURCE
/ -
/ +

ENGLISH
BEFORE YOU OPERATE THE MONITOR 15
Adjust the volume of sound
Press the / Button to adjust the volume of sound when the menu page is not displayed on
the screen.
Switch the input signal
This is activated when you successively press the VIDEO SOURCE Button on the monitor or
INPUT Button on the Remote Control as follows:
[Remote Control][Monitor]
VIDEO
SOURCE
/ -
/ +
[Remote Control][Monitor]
VIDEO
SOURCE
/ -
/ +

ENGLISH
16 BEFORE YOU OPERATE THE MONITOR
CONNECTING YOUR MONITOR
Ensure that both the computer and the monitor are switched off.
Connect the computer to the monitor with the signal cable.
Connect the computer to the monitor with the USB Cable.*
Connect the Power Cable to the monitor first and then to the power supply.
Turn on your monitor (Main Power Switch and Power Switch) and computer.
The signal cables used for connecting the computer and monitor may vary with the
type of computer used. An incorrect connection may cause serious damage to both
the monitor and the computer. The cable supplied with the monitor is for a standard
connector. If a special cable is required please contact your local iiyama dealer or
regional iiyama office.
For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyama office for a suitable adaptor.
Make sure you tighten the finger screws at each end of the Signal Cable.
Don’t connect the RS-232C cable and the USB cable to the computer at the same time.
And cannot use those at the same time.*
When USB cable connected than wait for 8 seconds and the touch function is ready to
go. It can be activated by pen, finger or any other pointer.*
[Example of Connection]
<Back>
NOTE
* Available for ProLite TH4264MIS only.
Computer
AV Equipment
VGA(D-sub)
Signal Cable
(Accessory)
DVI-D Cable
(Accessory)
HDMI Cable
(Not Included)
Power Cable
(Accessory)
USB Cable(Accessory) *
Audio Cable (Not Included)
DisplayPort
Cable
(Not Included)

ENGLISH
BEFORE YOU OPERATE THE MONITOR 17
[ Connection example with the peripheral device ]
CAUTION
Turn off the power switch and unplug the monitor and peripherals before connection to avoid electric
shock or damage.
NOTE
Refer to the user manual of peripherals at the same time.
Ensure you have the necessary cables as required.
Red
Blue
Green
Red White
Red White
Red Red
Black
Black