Ikan Blitz BZ2000-ANT User manual
BZ2000-ANT
High Gain Panel Antenna for Blitz 2000
1 x Panel Antenna
1 x Receiver Mounting Bracket
1 x Stand Mount Bracket
1 x Stand Mount Brace
5 x NJWC to SMA Coaxial Cable Connectors
4 x M3 Mounting Screws
4 x M4 Mounting Screws
www.ikancorp.com 713.272.8822
1Product Description
The Blitz BZ2000-ANT is a directional high-gain antenna compatible
with the Blitz BZ1000 receiver. The five antenna ports connect to the
panel antenna which can increase the maximum distance from 1000
ft to 2000 ft under the same conditions. This panel antenna will
increase distance as well as signal strength for shorter distances.
Follow these instructions carefully for best performance. If the
product is not used correctly, you may experience poor results.
Please view the contents in this manual for the detailed operation
instructions.
(For further instructions please consult your BZ1000-PRO manual.)
1
2
Model
Frequency Range
Gain
(F/B Ratio)
Isolation
Horizontal Beam Width
Vertical Beam Width
V.S.W.R
Polarization
Maximum Power
Impedance
Working Temperature
Connector Type
Lightning Protection
Installation Method
BZ2000-ANT
5.0-5.9GHz
14±0.5dBi
≥25dB
≥26dB
40±5º
40±5º
≤2.0
5 ports: 3 ports vertical,2 ports±45º
100W
50ohm
-40°C to + 55°C
5*N-K
DC-Ground
Bracket
Antenna Dimension
Antenna Material
Weight (Antenna and accessories)
Weight (Antenna and Receiver)
Rated Wind Velocity
12 x 12 x 0.9 in. (305 x 305 x 25 mm)
ABS
4.3 lbs (1.97 kg)
5.7 lbs (2.6 kg)
36.9 m/s
Physical Specification
Specifications
2
Performance Parameters
3
3
1 x Panel Antenna 1 x Receiver
Mounting Bracket
5 x NJWC to SMA coaxial
cable connectors
4 x M3 Mounting
Screws
Packing List
1 x Stand Mount
Brace
4 x M4 Mounting
Screws
4
2
1
3
4
4
5
Installation Guide
4
1
2
3
4
5
5
Installation Guide
Install the stand mount brace to t he receiver mounting bracket
using the 4pcs M3*8 screws.
Place the BZ1000 receiver on the receiver bracket and line up the 4
holes from the Ikan Quick Mount system on the front of the unit to
the 4 holes on the receiver bracket. Use the included 4 x M4
screws to then attach the receiver to the bracket.
Attach the receiver mounting bracket to the panel antenna with
the 4pcs M4*8 screws, and connect the 5 ports of the antenna
to the 5 ports on the receiver with the included coaxial cable
connectors.
Attach the complete assembly to a light stand via the 3/8"-16
threaded hole on the stand mount brace.
Install a v-mount battery and any video cables on the receiver.
5
6
Ground
Top view
Transmitter Receiver
45°
Side view
TX & RX Must Face Each Other
Installation Diagram
The receiver should be at least
2 meters off the ground.
6
7
Troubleshooting
(1) If there is no video signal within 10 to 30 ft, then check the video input
source and output.
(2) If you experience poor video quality from 1000 to 2000 ft please check
whether the transmitter and receiver are set up as outlined in this manual. If
they are setup correctly, then check if the coaxial cables on the antenna are
connected properly, damaged, or if the port is dirty.
(3) If you experience image noise it may be due to wireless interference.
Please try a different wireless channel.
(4) When using the panel antenna outside with a light stand make sure to use
sandbags or other type of reinforcements on the stand to keep it from
falling.
(5) When the system is not in use please keep all components in the included
box in order to keep them safe and clean.
www.ikancorp.com
Table of contents
Other Ikan Antenna manuals
