IKE 4 User manual

7
1
2
3
1
4
5
7
9
6
7
8
4
The IKE 4 Tripod has a low magnetic
signature and is designed specically
for use with the IKE device to produce
accurate measurements.
We do not recommend using your device
with other tripods as the accuracy of your
measurements may be affected.
Squeeze the small lever and turn it to
release the tripod plate.
Lower the IKE unit into position and
then turn the lever fully to lock the unit
into place.
Remove the tripod from its bag. Open
up the legs of the tripod. Unclip the
tripod leg locks and extend the legs to
the required height. Clip back to secure
the legs. Lower the main lever to a
horizontal position.
Hold the lever outwards and clip the
tripod plate on the back of the IKE device
to the tripod.
Attach the tripod plate to the base of
the IKE device ensuring it is positioned
correctly as shown below.
Tighten the screw until it is secure.
IKE 4 TRIPOD
Setup Guide
Prepare Mount
1 2
Package Contents
Tripod
Carry strap (attaches to bag or tripod)
Allen keys (2)
Allen key holder (hooks on to tripod leg)
Leg strap (with carry strap eyelet)
Storage bag
Setup Guide (this guide)
Parts
1Tripod plate
2Adjustment ring
3Leg angle adjustment clip
4Leg lock
5Rubber/spike feet
6Shoulder strap eyelet
7Main lever
8Lever
9Friction dial
Ensure that the IKE unit is securely
attached.

For span and pole height measuring, you
can further tighten the movement of the
lever so that the ball joint remains locked yet
the pitch mechanism is still moveable. To do
this, while pressing the main lever with one
hand, use your other hand to turn the friction
dial and adjust the tension. Test the tension
of the movement between adjustments.
The leg hinges may loosen over time. If
this happens, use the Allen key provided
to tighten the screws.
Rotate the lever towards you to the
opposite side.
Place the tripod inside the carry bag and
zip up the bag.
The strap provided can be used both on
the tripod or on the carry bag.
To adjust the position of the IKE device,
with one hand hold the unit, and with
your other hand squeeze the main lever
and move to adjust. You can turn in all
directions.
You can ne tune the height of the unit.
Turn the adjustment ring counterclockwise
to loosen it and lift the centre pole. Turn
the adjustment ring clockwise to tighten
into place.
If you are left-handed, you can change the
position of the lever to the opposite side.
With the tripod plate removed (see step
1), use the Allen key provided to unscrew
the two screws on the tripod head. Then
remove the top plate.
We recommend storing your tripod in the
carry bag after use.
Remove the IKE unit from the tripod and
make the tripod as compact as possible.
Secure the legs with the leg strap. Then
lift the main lever to a vertical position.
Replace the top plate as shown and
secure tightly with the two screws.
Adjust Left-handed Use Carry Bag
3
Specications
Aluminum, carbon ber
Max 59.5 in. (1510 mm)
5.1 lb (2.31 kg)
(with accessories)
Low magnetic
Copyright © 2016 ikeGPS
IKE 4 TRIPOD Setup Guide V1 (1501)
Leg Strap
The leg strap allows you to secure the legs
closed when not in use, and also provides
the eyelet for attaching the carry strap to it.
Attach the leg strap just under the padding
on one of the legs. Wrap the strap around
the leg and thread it through the buckle.
Secure it in place with the velcro. You can
then attach the carry strap to the eyelet on
the leg strap and to the eyelet on the tripod.
Materials:
Maximum height:
Weight:
Signature: