IKEA ELDSLAGA User manual

4 0 0 0113 413 02
© Inter IKEA Systems B.V. 2019 18535 AA-2118906-1

ENGLISH 3
5 يبرع

ENGLISH 3
Before using the appliance, read
these safety instructions. Keep
them nearby for future reference.
These instructions and the
appliance itself provide important
safety warnings, to be observed
at all times. The manufacturer
declines any liability for failure to
observe these safety instructions,
for inappropriate use of the
appliance or incorrect setting of
controls.
These instructions are valid if
the country symbol appears on the
appliance. If the symbol doesn’t
appear on the appliance, it is
necessary to refer to the technical
instructions which will provide the
necessary instructions concerning
modication of the appliance
to the conditions of use of the
country.
CAUTION: The use of the
gas cooking appliance results in
the production of heat, moisture
and products of combustion in
the room in which it is installed.
Ensure that the kitchen is well
ventilated especially when the
appliance is in use: keep natural
Safety Information
Table of contents
ventilation holes open or install
a mechanical ventilation device
(mechanical extractor hood).
Prolonged intensive use of the
appliance may call for additional
ventilation, for example opening
of the window, or more effective
ventilation,increasing the level
of mechanical ventilation where
present.
WARNING!: The appliance
and its accessible parts become
hot during use. Care should be
taken to avoid touching heating
elements. Children less than 8
years of age must be kept away
unless continuously supervised.
WARNING!: If the hob surface
is cracked, don’t use the appliance
– risk of electrical shock.
WARNING!: Danger of re :
Do not store items on the cooking
surfaces.
CAUTION: The cooking process
has to be supervised.
A short cooking process has to be
supervised continuously.
WARNING!:Unattended
cooking on a hob with fat or oil
Safety Information 3
Product description 9
Daily use 9
Helpful hints and tips 10
Maintenance and cleaning 10
What to do if ... 11
Injector table 12
Technical data 13
Installation 13
Environmental concerns 17
Manufacturer 17
IKEA GUARANTEE 18

ENGLISH 4
can be dangerous – risk of re.
NEVER try to extinguish a re with
water, but switch off the appliance
and then cover ame e.g. with a
lid or a re blanket.
Do not use the hob as a work
surface or support.
Keep clothes or other ammable
materials away from the
appliance, until all the components
have cooled down completely –
risk of re.
IIf the information in this
manual is not followed exactly,
a re or explosion , may result
causing property damage or
injury.
Very young children (0-3 years)
should be kept away from the
appliance. Young children (3-8
years) should be kept away from
the appliance unless continuously
supervised. Children from 8 years
old and above and persons
with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge can
use this appliance only if they
are supervised or have been
given instructions on safe use and
understand the hazards involved.
Children must not play with the
appliance. Cleaning and user
maintenance must not be carried
out by children without supervision.
CAUTION: IIn case of hotplate
glass breakage:- shut immediately
off all burners and any electrical
heating element and isolate the
appliance from the power supply;
- do not touch the appliance
surface; -do not use the appliance.
The glass lid can break in if it
is heated up. Turn off all the
burners and the electric plates
before closing the lid. Do not
shout down lid when burner
alight.
PERMITTED USE
CAUTION: the appliance is not
intended to be operated by means
of an external switching device,
such as a timer, or separate remote
controlled system.
This appliance is intended
to be used in household and
similar applications such as: staff
kitchen areas in shops, ofces
and other working environments;
farm houses; by clients in hotels,
motels, bed & breakfast and other
residential environments.
No other use is permitted (e.g.
heating rooms).
This appliance is not for
professional use. Do not use the
appliance outdoors.
Use pots and pans with
bottoms the same width as that of
the burners or slightly larger (see
specic table). Make sure pots on
the grates do not protrude beyond
the edge of the hob.
Improper use of the grids can
result in damage to the hob: do

ENGLISH 5
not position the grids upside down
or slide them across the hob.
Do not let the burner ame extend
beyond the edge of the pan.
Do not use : Cast iron griddles,
ollar stones, terracotta pots and
pans.
Heat diffusers such as metal mesh,
or any other types. Two burners
simultaneously for one receptacle
(e.g. Fish kettle).
Should particular local conditions
of the delivered gas make the
ignition of burner difcult, it is
advisable to repeat the operation
with the knob turned to small ame
setting.
In case of installation of a hood
above the cooktop, please refer
to the hood instructions for the
correct distance.
The protective rubber feet on the
grids represent a chocking hazard
for young children. After removing
the grids, please ensure that all the
feet are correctly tted.
INSTALLATION
The appliance must be
handled and installed by two or
more persons - risk of injury. Use
protective gloves to unpack and
install - risk of cuts.
Installation, including water
supply (if any) and electrical
connections, and repairs must
be carried out by a qualied
technician. Do not repair or
replace any part of the appliance
unless specically stated in the
user manual. Keep children away
from the installation site. After
unpacking the appliance, make
sure that it has not been damaged
during transport. In the event of
problems, contact the dealer or
your nearest Aftersales Service.
Once installed, packaging waste
(plastic, styrofoam parts etc.)
must be stored out of reach of
children - risk of suffocation. The
appliance must be disconnected
from the power supply before
any installation operation - risk of
electrical shock. During installation,
make sure the appliance does not
damage the power cable - risk
of re or electrical shock. Only
activate the appliance when the
installation has been completed.
The electrical and gas
connections must comply
with local regulation.
WARNING!: Modication of
the appliance and its method of
installation are essential in order
to use the appliance safely and
correctly in all the additional
countries.
Use pressure regulators
suitable for the gas pressure
indicated in the instruction.
The room must be equipped
with an air extraction system that
expels any combustion fumes.
The room must also allow

ENGLISH 6
proper air circulation, as air is
needed for combustion to occur
normally.
The ow of air must not be less
than 2 m3/h per kW of installed
power.
The air circulation system
may take air directly from the
outside by means of a pipe with
an inner cross section of at least
100 cm2; the opening must not
be vulnerable to any type of
blockages.
The system can also provide
the air needed for combustion
indirectly, i.e. from adjacent rooms
tted with air circulation tubes as
described above. However, these
rooms must not be communal
rooms, bedrooms or rooms that
may present a re hazard.
Liquid petroleum gas sinks to
the oor as it is heavier than air.
Therefore, rooms containing LPG
cylinders must also be equipped
with vents to allow gas to escape
in the event of a leak. As a result
LPG cylinders, whether partially
or completely full, must not be
installed or stored in rooms or
storage areas that are below
ground level (cellars, etc.). It is
advisable to keep only the cylinder
being used in the room, positioned
so that it is not subject to heat
produced by external sources
(ovens, replaces, stoves, etc. )
which could raise the temperature
of the cylinder above 50°C.
Carry out all cabinet cutting
works before tting the appliance
in the furniture and remove all
wood chips and sawdust.
If the appliance is Not installed
above an oven, a separator panel
(not included) must be installed
in the compartment under the
appliance.
Should you experience difculty in
turning the burners knobs, please
contact After Sales Service for
replacement of the burner tap if
found to be faulty.
The openings used for the
ventilation and dispersion of heat
must never be covered.
GAS CONNECTION
WARNING!: Prior to
installation, ensure that the local
distribution conditions (nature of
gas and gas pressure) and the
adjustment of the appliance are
compatible.
Check that the pressure
of the gas supply is consistent
with the values indicated in
Table 1 (“Burner and nozzle
specications”).
WARNING!: The adjustment
conditions for this appliance are
stated on the label (or data plate).
WARNING!: This appliance
is not connected to a combustion
products evacuation device. It
shall be installed and connected

ENGLISH 7
in accordance with current
installation regulations. Particular
attention shall be given to the
relevant requirements regarding
ventilation.
IIf the appliances is connected
to liquid gas, the regulation screw
must be fastened as tightly as
possible.
IMPORTANT: When gas
cylinder is adopted, the gas
cylinder or gas container must
be properly settled (vertical
orientation).
WARNING!: This operation
must be performed by a qualied
technician.
Use only exible or rigid metal
hose for gas connection.
Connection with a rigid pipe
(copper or steel) Connection to
the gas system must be carried
out in such a way as not to
place any strain of any kind
on the appliance. There is an
adjustable L-shaped pipe tting
on the appliance supply ramp
and this is tted with a seal in
order to prevent leaks. The seal
must always be replaced after
rotating the pipe tting (the seal
is provided with the appliance).
The gas supply pipe tting is a
threaded 1/2 gas cylindrical male
attachment.
Connecting a exible jointless
stainless steel pipe to a threaded
attachment The gas supply pipe
tting is a threaded 1/2 gas
cylindrical male attachment.
These pipes must be installed so
that they are never longer than
2000 mm when fully extended.
Once connection has been
carried out, make sure that the
exible metal pipe does not
touch any moving parts and is
not compressed. Only use pipes
and seals that comply with current
National regulations.
IMPORTANT: If a stainless steel
hose is used, it must be installed
so as not touch any mobile part of
the furniture (e.g. drawer). It must
pass through an area where there
are no obstructions and where it
is possible to inspect it on all its
length.
The appliance should be
connected to the main gas supply
or to gas cylinder in compliance
with the current National
regulations. Before carry out the
connection, make sure that the
appliance is compatible with the
gas supply you wish to use. If this is
not the case, follow the instructions
indicated in the paragraph
“Adapting to different types of
gas”.
After connection to the gas
supply, check for leaks with soapy
water. Light up the burners and
turn the knobs from max position
1* to minimum position 2* to check
ame stability.

ENGLISH 8
ADAPTING TO DIFFERENT TYPES
OF GAS
In order to adapt the
appliance to a type of gas other
than the type for which it was
manufactured (indicated on the
rating label), follow the dedicated
steps provided after installation
drawings.
ELECTRICAL WARNINGS
IMPORTANT: The data
relevant to the voltage an power
absorptions are indicated on the
rating plate.
The power cable must be long
enough to connect the appliance,
once tted in its housing, to the
main power supply. Do not pull the
power supply cable.
It must be possible to
disconnect the appliance from the
power supply by unplugging it if
plug is accessible, or by a multi-
pole switch installed upstream of
the socket in accordance with the
wiring rules and the appliance
must be earthed in conformity
with national electrical safety
standards.
Do not use extension leads,
multiple sockets or adapters.
The electrical components must
not be accessible to the user
after installation. Do not use the
appliance when you are wet or
barefoot. Do not operate this
appliance if it has a damaged
power cable or plug, if it is not
working properly, or if it has been
damaged or dropped.
If the supply cord is damaged,
it must be replaced with an
identical one by the manufacturer,
its service agent or similarly
qualied persons in order to avoid
a hazard - risk of electrical shock.

ENGLISH 9
Product description
1Removable panstand grids
2Rapid burner
3Semirapid burner
4Auxiliary burner
5Semirapid burner
6Power burner
7Power burner control knob
8Semirapid burner control knob
9Auxiliary burner control knob
10 Rapid burner control knob
11 Semirapid burner control knob
1
2
3
6
4
7 8 9 10 11
5
Symbols
Solid disc Tap closed
Large ame
and star
Maximum opening/
delivery and electric
ignition
Small ame Minimum opening or
reduced delivery
Do not let the burner ame extend
beyond the edge of the pan.
IMPORTANT: when the hob is in use, the
entire hob area may become hot.
- To ignite one of the burners, turn the
relative knob anti-clockwise to the
maximum ame setting.
- Press the knob against the control panel
to ignite the burner.
- After the burner has ignited, keep the
knob pressed for about 5-10 seconds to
allow proper device operation.
This burner safety device shuts off the gas
supply to the burner if the ame goes out
accidentally (because of sudden draught, an
interruption in the gas delivery, boiling over
of liquids, etc.).
- The knob must not be pressed for
more than 15 sec. If, after that time has
elapsed, the burner does not remain lit,
wait at least one minute before trying to
light it again.
NOTE: should particular local conditions
of the delivered gas make the ignition of
burner difcult, it is advisable to repeat
the operation with the knob turned to small
ame setting.
The burner might go out when the knob is
released. This means that the safety device
has not warmed up enough. In this
case, repeat the operations described
above.
Daily use

ENGLISH 10
This hob has burners of different diameters.
For better burner performance, please stick
to the following rules:
- Use pots and pans with bottoms the
same width as that of the burners or
slightly larger (see following table).
- Only use at-bottomed pots and pans.
- Use the correct amount of water
for cooking foods and keep the pot
covered.
- Make sure pots on the grates do not
protrude beyond the edge of the hob.
Burner Pot Ø
Power burner from 24 to 26 cm
Rapid from 24 to 26 cm
Burner Pot Ø
Semi-rapid from 16 to 24 cm
Auxiliary from 8 to 14 cm
IMPORTANT: improper use of the grids can
result in damage to the hob: do not position
the grids upside down or slide them across
the hob. Do not use:
- Cast iron griddles, ollar stones,
terracotta pots and pans.
- Heat diffusers such as metal mesh, or
any other types.
- Two burners simultaneously for one
receptacle (e.g. sh kettle).
Helpful hints and tips
WARNING!: Ensure that the appliance
is switched off and disconnected from
the power supply before performing any
maintenance operation; never use steam
cleaning equipment - risk of electric shock.
Do not use abrasive or corrosive
products, chlorine-based cleaners or pan
scourers.
CLEANING THE HOB PARTS
- Grids, burner caps and burners can be
removed to be cleaned.
- Clean them by hand with warm water
and non-abrasive detergent, removing
any food residues and checking that
none of the burner openings is clogged.
- Rinse and dry
- Ret burners and burner caps correctly
in the respective housings.
- When replacing the grids, make sure
that the panstand area is aligned with
the burner.
- Models equipped with electrical
ignition plugs and safety device require
thorough cleaning of the plug end in
order to ensure correct operation.
Check these items frequently, and if
necessary, clean them with a damp
cloth. Any baked-on food should be
removed with a toothpick or needle.
NOTE: to avoid damaging the electric
ignition device, do not use it when the
burners are not in their housing.
Maintenance and cleaning

ENGLISH 11
Problem Possible cause Solution
The electric ignition does not
work
There is no electrical
supply
Check the unit is plugged in
and the electrical supply is
switched on.
The burner fails to ignite The gas tap could be
closed
Check that the gas tap is
open
The gas ring burns unevenly Burner crown may
be occluded by food
residues
Clean the burner crown
according to cleaning
instructions to make sure that
the burner crown is clear of
food residues.
What to do if ...
Before calling the After-Sales Service:
1. Check “Troubleshooting guide” to see if
you can eliminate the problem yourself
2. Turn the hob on again to check if correct
operation has been restored.
3. If the problem persists, contact the After-
sales Service.
Give the following information:
• type of fault;
• hob model;
• service number (i.e. the number after the
word SERVICE on the dataplate under
the hob and on the warranty certicate);
• your full address;
• your telephone number.
If any repairs are required, contact an
authorised service centre, indicated in the
warranty.
In the unlikely event that an operation or
repair is carried out by an unauthorised
technician, always request certication
of the work carried out and insist on the use
of original spare parts.
Failure to comply with these instructions
may compromise the safety and quality of
the product.

ENGLISH 12
Injector table
Type of gas used Type of
burner
Injector
marking
Rated
thermal
ow rate
kW
Rated
consumption
Reduced
heat
capacity
kW
Gas pressure
(mbar)
min. rat. max.
LIQUEFIED
PETROLEUM GAS
(Butane) G30
power burner
rapid
semi-rapid
auxiliary
93
85
69
50
3,70
3,00
2,00
1,00
269 g/h
218 g/h
145 g/h
73 g/h
1,90
0,70
0,40
0,35
25 30 35
LIQUEFIED
PETROLEUM GAS
(Propane) G31
power burner
rapid
semi-rapid
auxiliary
93
85
69
50
3,70
3,00
2,00
1,00
264 g/h
214 g/h
143 g/h
71 g/h
1,90
0,70
0,40
0,35
25 30 35
NATURAL GAS
(Methane) G20
power burner
rapid
semi-rapid
auxiliary
146 A
115 Y
101 Z
72X
4,00
3,00
2,00
1,00
381 l/h
286 l/h
190 l/h
95 l/h
2,20
0,60
0,35
0,30
17 20 25
Type of gas used Model conguration
5 BURNERS
Rated thermal
owrate (kW)
Total rated
consumption
Air required (m
3
) for
burning 1m
3
of gas
G30 30 mbar 1 PB - 1 R 2 SR - 1 AUX 11 , 7 0 851 g/h 30,94
G31 30 mbar 1 PB - 1 R 2 SR - 1 AUX 11 , 7 0 836 g/h 23,80
G20 20 mbar 1 PB - 1 R 2 SR - 1 AUX 12,00 1142 l/h 9,52
Electric Power: 220 - 240 V ~ 50 - 60 Hz 0,6W
Category II2H3B/P

ENGLISH 13
Technical data
Dimensions
Width (mm) 730
Height (mm) 40
Length (mm) 510
Voltage (V) 220 - 240
The technical information are situated in the
rating plate on the bottom side of the
appliance.
Installation
After unpacking the hob, make sure that it
has not been damaged during transport. In
the event of problems, contact the dealer or
your nearest After-sales Service.
Technical information for the installer
- This product can be embedded in a
worktop 20 to 50 mm thick.
- If there is no oven beneath the hob,
insert a separator panel that has a
surface at least equal to the opening
in the work surface. This panel must be
positioned in no case less than 20 mm
from the bottom of the hob.
- Before installation, make sure that:
- the local gas delivery conditions (nature
and pressure) are compatible with the
settings of the hob (see the rating plate
and injector table);
- the outer surfaces of the furniture or
appliances adjacent to the hob are heat
resistant according to local regulations;
- This appliance is not connected to a
fume exhaust device. It shall be installed
in accordance with current installation
regulations. Particular attention shall
be given to the relevant requirement
regarding ventilation.
- Combustion products are discharged
outdoors through specic hoods or wall
and/or window mounted electrical fans.
Gas connection
This operation must be performed by a
qualied technician.
The gas supply system must comply with
local regulations to the relavant gas
standard.
- You can nd specic local regulations for
some countries in the paragraph
- “Reference to Local Regulations”. If no
information concerning your Country is
given, please ask details to a qualied
technician.
- The connection of the hob to the gas
pipe network or gas cylinder must be
made by means of a rigid copper or
steel pipe with ttings complying with
local regulations, or by means of a
continuous-surface stainless steel hose
complying with local regulations. The
maximum length of the hose is 2 linear
metres.

ENGLISH 14
A
B
C
C
D
D
- Connect elbow (A) or (B) supplied with
to the hob inlet main pipe and interpose
the washer (C) supplied, in compliance
with EN 549.
- Washer (D) not supplied with the
product.
IMPORTANT: if a stainless steel hose is
used, it must be installed so as not to touch
any mobile part of the furniture. It must
pass through an area where there are no
obstructions and where it is possible to
inspect it on all its length.
- After connection to the gas supply, check
for leaks with soapy water. Light up the
burners and turn the knobs from max
position to minimum position to
check ame stability
Electrical connection
WARNING
- This operation must be performed by a
qualied technician.
- The electrical connections must comply
with local regulations.
- The earthing of this appliance is
compulsory by law.
L
N
Earth
(yellow/green)
- Do not use an extension cord.
IMPORTANT: the data relevant to the
voltage and power absorption are indicated
on the rating plate.
Assembly
After having cleaned the perimeter surface,
apply the supplied gasket to the hob.
Position the hob in the worktop opening
made respecting the dimensions indicated
in the Instruction.
NOTE: the power supply cable must be long
enough to permit its upward extraction.
To secure the hob, use the brackets provided
with it. Fit the brackets into the relevant
bores shown by the arrow and fasten them
by means of their screws in accordance with
the thickness of the worktop.
Make sure that the outlet is near the product
to install. So, if the cable that came with the
product is not long enough, you will need to
replace it with another one having the same
features but with the right length.
Adjustment to different type of gas
WARNING: This operation must be
performed by a qualied technician.
If the appliance is intended to operate with
a different gas from the gas type stated on
the rating plate and information label on
the top of the hob, change the injectors.
Remove the information label and keep it
with the instructions booklet.
Use pressure regulators suitable for the gas
pressure indicated in the Instruction.
- The gas nozzles must be changed
by After Sales Service or a qualied
technician.

ENGLISH 15
- Nozzles not supplied with the appliance
must be ordered from After Sales
Service.
- Adjust the minimum setting of the taps.
NOTE: when liquid petroleum gas is used
(G30/G31), the minimum gas setting screw
must be tightened as far as it will go.
IMPORTANT: should you experience
difculty in turning the burners knobs,
please contact the After Sales Service for
the replacement of the burner tap if found to
be faulty.
Replacing the injectors (see paragraph
“injector table”)
- Remove grids (A).
- Extract burners (B).
- Using a socket spanner of the
appropriate size unscrew the injector
(C), unscrew the injector to be replaced.
- Replace it with the injector suitable for
the new type of gas.
- Re-assemble the injector in (D).
Before installing the hob, remember to afx
the gas calibration plate supplied with
the injectors in such a way that it covers
the existing information relating to gas
calibration.
D
C
A
B
Adjusting minimum gas setting of taps
E
To ensure that the minimum setting is
correctly adjusted, remove the knob (E) and
proceed as follows:
- tighten screw to reduce the ame height
(-);
- loosen screw to increase the ame
height (+).
The adjustment must be performed with the
tap in minimum gas setting position (small
ame).
- The primary air of the burners does not
need to be adjusted.
- At this stage, light up the burners and
turn the knobs from max position
to minimum position to check ame
stability.
Upon completion of adjustment, reseal
the work surface using sealing wax or an
equivalent material.
REFERENCE TO LOCAL REGULATIONS
Ensure that the installation and gas
connections are performed by a qualied
technician, following the manufacturer’s
instructions and in compliance with current
local safety regulations.

ENGLISH 16
WOK ADAPTER
KNOBS REPLACEMENT
Be sure that your hob is switched-off.
All knobs must be in closed position.
Pull upwards each knob of the cooktop and
store together after removal.
Take the kit with new knobs, which is located
in upper part of packaging and remove the
new knobs from the plastic bag.
Push each of knob on the valve shaft until
you feel the end of sliding (sparking may
occur).
Make sure that all the knobs are in the right
position.
Verify correct installation by switching each
burner separately.

ENGLISH 17
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable
and is marked with the recycle symbol .
The various parts of the packaging must
therefore be disposed of responsibly and
in full compliance with local authority
regulations governing waste disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with
recyclable or reusable materials.
Dispose of it in accordance with local waste
disposal regulations.
For further information on the treatment,
recovery and recycling of household
electrical appliances, contact your local
authority, the collection service for
household waste or the store where you
purchased the appliance. This appliance
is marked in compliance with European
Directive 2012/19/EU, Waste Electrical and
Electronic Equipment (WEEE).
By ensuring this product is disposed of
correctly, you will help prevent negative
consequences for the environment and
human health.
The symbol on the product or on the
accompanying documentation indicates
that it should not be treated as domestic
waste but must be taken to an appropriate
collection center for the recycling of
electrical and electronic equipment.
Ikea of Sweden AB
SE - 343 81 Älmhult, Sweden
Environmental concerns
Manufacturer
ENERGY SAVING TIPS
Use pots and pans with bottom width equal
to that of the cooking zone.
Only use at-bottomed pots and pans.
When possible, keep pot lids on during
cooking.
Use a pressure cooker to save even more
energy and time.
Place the pot in the middle of the cooking
zone marked on the hob.
DECLARATION OF CONFORMITY
This appliance meets the Ecodesign
requirements set out in European Regulation
n. 66/2014, in conformity to the European
standard EN 30-2-1.

ENGLISH 18
How long is the IKEA guarantee valid?
This guarantee is valid for ve (5) years - two
(2) years if the appliance is named LAGAN or
TILLREDA - from the original date of purchase
of your appliance at IKEA or from the
installation date with maximum limit of three
months from the purchase date.
The original sales receipt, is required as proof
of purchase.
If service work is carried out under guarantee,
this will not extend the guarantee period for
the appliance.
Once a warranted product has been replaced,
the replaced product warranty will be valid
for the balance period from date of original
purchase invoice
Who will execute the service?
IKEA service provider will provide the
service through its own service operations or
authorized service partner network.
What does this guarantee cover?
• The guarantee covers faults of the
appliance, which have been caused by
faulty construction or material faults from
the date of purchase from IKEA or from the
installation date with maximum limit of three
months from the purchase date.
• This guarantee applies to domestic use only.
• The exceptions are specied under the
headline “What is not covered under this
guarantee?” Within the guarantee period,
• The costs to remedy the fault e.g. repairs,
parts, labour and travel will be covered,
provided that the appliance is accessible for
repair without special expenditure. On these
conditions the respective local regulations
are applicable.
• Replaced parts become the property of
IKEA.
• In case of non-repairable product, the retail
value of the replacement will not exceed
the purchase price that was paid by the
customer
IKEA GUARANTEE
What will IKEA do to correct the problem?
• IKEA appointed Service Provider will
examine the product and decide, at its
sole discretion, if it is covered under this
guarantee. If considered covered, IKEA
Service Provider or its authorized service
partner through its own service operations,
will then, at its sole discretion, either repair
the defective product or replace it with the
same or a comparable product.
What is not covered under this guarantee?
• Normal wear and tear.
• Deliberate or negligent damage, damage
caused by failure to observe operating
instructions, incorrect installation or by
connection to the wrong voltage, damage
caused by chemical or electrochemical
reaction, rust, corrosion or water damage
including but not limited to damage caused
by excessive lime in the water supply,
damage caused by abnormal environmental
conditions.
• Consumable parts including batteries and
lamps.
• Non-functional and decorative parts which
do not affect normal use of the appliance,
including any scratches and possible colour
differences.
• Accidental damage caused by foreign
objects or substances and cleaning or
unblocking of lters, drainage systems or
soap drawers.
• Damage to the following parts: ceramic
glass, accessories, crockery and cutlery
baskets, feed and drainage pipes, seals,
lamps and lamp covers, screens, knobs,
casings and parts of casings. Unless such
damages can be proved to have been
caused by production faults.
• Cases where no fault could be found during
a technician’s visit.
• Repairs not carried out by our appointed
service providers and/or an authorized
service contractual partner or where non-
original parts have been used.

ENGLISH 19
• Repairs caused by installation which is faulty
or not according to specication
• The use of the appliance in a non-domestic
environment i.e. professional use.
• Transportation damages. If a customer
transports the product to his home or
another address, IKEA is not liable for any
damage that may occur during transport.
However, if IKEA delivers the product to the
customer’s delivery address, then damage
to the product that occurs during this
delivery will be covered by IKEA.
• Damage resulting from power outage,
power surges or dips, uctuating voltage or
improper voltage All workout parts are not
covered by the guarantee e.g.: lters and
cleanliness.
• Cost for carrying out the initial installation
of the IKEA appliance. However, if an
IKEA appointed Service Provider or its
authorized service partner repairs or
replaces the appliance under the terms
of this guarantee, the appointed Service
Provider or its authorized service partner
will reinstall the repaired appliance or install
the replacement, if necessary.
• All plumping and electrical installation, are
not the responsibility of IKEA, and customer
must complete these work before the
execution work.
How country law applies
The IKEA guarantee gives you specic legal
rights, which cover or exceed all the local legal
demands. However these conditions do not
limit in any way consumer rights described in
the local legislation.
Area of validity
This warranty is valid only in the country where
the product has been purchased; the services
will be provided in the framework of the
guarantee conditions.
An obligation to carry out services in the
framework of the guarantee exists only if
the appliance complies and is installed in
accordance with:
- the technical specications of the country in
which the guarantee claim is made;
- the Assembly Instructions and User Manual
Safety Information.
The dedicated AFTER SALES for IKEA
appliances
Please don’t hesitate to contact IKEA
appointed After Sales Service Provider to:
• make a service request under this
guarantee;
• ask for clarications on installation of the
IKEA appliance in the dedicated IKEA
kitchen furniture;
• ask for clarication on functions of IKEA
appliances.
To ensure that we provide you with the best
assistance, please read carefully the Assembly
Instructions and/or the User Manual before
contacting us.
How to reach us if you need our service
Please refer to the last
page of this manual for the
full list of IKEA appointed
Authorized Service Centre
and relative national phone
numbers.
In order to provide you a quicker
service, we recommend to use the
specic phone numbers listed on this
manual. Please also always refer to
the IKEA article number (8 digit code)
placed on the rating plate of your
appliance.
SAVE THE SALES RECEIPT!
It is your proof of purchase and required
for the guarantee to apply. The sales
receipt also reports the IKEA name and
article number (8 digit code) for each of
the appliances you have purchased.

UNITED ARAB EMIRATES
Toll free:
Web:
800 4532
www.IKEA.com
: 
: 
QATAR
Toll free:
Web:
e-mail:
800 4532
www.IKEA.qa
[e-mail]
: 
: 
: 
EGYPT
Hotline:
Web:
e-mail:
16576
www.IKEA.eg
IkeaCairo.cust[email protected]
: 
: 
: 
STATE OF KUWAIT
Contact centre:
Web:
e-mail:
[phone]
www.IKEA.com.kw
[email protected]
: 
: 
: 
JORDAN
Contact centre:
Web:
[phone]
www.IKEA.jo
: 
: 
KINGDOM OF SAUDI ARABIA
Contact centre:
Our phone lines are open:
Saturday - Thursday
Friday
92000-4532
09:00 AM - 10:00 PM
2:00 PM - 10:00 PM
: 
: 


BAHRAIN
Contact centre:
Our telephone lines are open
all day
80001120
09:00 AM - 10:00 PM
: 
