Image 831.100430 User manual

USER’S MANUAL
QUESTIONS?
As a manufacturer, we are com-
mitted to roviding com lete
customer satisfaction. If you
have questions, or find that there
are missing or damaged arts,
we will guarantee com lete satis-
faction through direct assistance
from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will rovide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-888-936-4266
Mon.–Thu., 8:00 am—6:30 m;
Fri., 8:00 am—6:00 m EST
Model No. 831.100430
Serial No.
Write the serial number in the space
above for reference.
Patent Pending
CAUTION
Read all recautions and instruc-
tions in this manual before using
this equi ment. Save this manual
for future reference.
Serial Number Decal
®
SEARS CANADA, INC., TORONTO, ONTARIO M5B 2B8

TABLE OF CONTENTS
IMPOR AN SAFE Y INS RUC IONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
WARNING DECAL PLACEMEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CHOOSING A LOCA ION FOR HE RENEW 900 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
USING HE RENEW 900 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
MAIN ENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ROUBLE-SHOO ING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ORDERING REPLACEMEN PAR S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
LIMI ED WARRAN Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Note: A PAR LIS and an EXPLODED DRAWING are attached to the center of this manual.
2

3
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of drowning, electric shock, or serious injury, read the following
im ortant recautions before using the RENEW 900.
READ AND FOLLOW ALL INSTRUCTIONS
1. It is the res onsibility of the owner to ensure
that all users of the RENEW 900 are ade-
quately informed of all recautions.
2. Use the RENEW 900 only as described in this
manual.
3. The RENEW 900 is intended for home use
only. Do not use the RENEW 900 in any com-
mercial, rental, or institutional setting.
4. Use the RENEW 900 only on a level surface.
Do not use the RENEW 900 on car et or
other materials that could be damaged by
moisture. Do not use the RENEW 900 on
rough or shar surfaces such as gravel or
wood chi s.
5. The RENEW 900 will weigh a roximately
2400 ounds when it is assembled and filled
with water. Be sure that the location you
select for the RENEW 900 will su ort this
weight, lus the weight of the occu ants.
6. Ins ect and tighten all arts regularly.
Re lace any worn arts immediately.
7. DANGER—Risk of injury: Do not remove or
alter the covers on the suction fittings. Never
o erate the RENEW 900 if the suction guard
is missing or broken. Kee hair and body
away from the suction guard. If you need to
re lace a suction fitting, be sure that the flow
rate of the re lacement is com atible.
8. Do not bring any object into the RENEW 900
that could uncture the liner.
9. Never insert any object into any o ening.
10. Do not sit on the s a cover or lace objects
on it. It is not designed to su ort weight.
11. Remove any water which may collect on the
s a cover.
12. Kee children and ets away from the
RENEW 900 when it is not in use.
13. Kee all chemicals away from children and
ets.
14. The H and chemical balance of the water
must be maintained as ex lained in this man-
ual (see age 13). Failure to do so may cause
injury to users or damage to the s a jet unit,
and will void the warranty.
15. The water um in the s a jet unit must be
rimed before you use the RENEW 900 the
first time. You must also rime the um
before using the unit each time you re-fill the
s a. The s a jet unit may be seriously dam-
aged if the um is not ro erly rimed (see
PRIMING THE SPA JET UNIT on age 10).
16. DANGER—When connecting the ower cord
(see PLUGGING IN THE RENEW 900 on age
10), lug the ower cord directly into a
grounded circuit ca able of carrying 15 or
more am s. No other a liance should be on
the same circuit. Re lace the ower cord
immediately if damaged.
17. Do not use an extension cord with the
RENEW 900. This could damage the motor
and will void the warranty.
18. DANGER—If you will be using the RENEW
900 outside, do not bury the ower cord; you
should also kee the ower cord away from
lawn mowers, hedge trimmers, and other
similar equi ment.
19. WARNING—The ower cord is equi ed with
a Ground Fault Circuit Interru ter (GFCI),
located at the end of the ower cord. The
GFCI must be tested before each use. To test
the GFCI, ress the “test” button while the
s a jet unit is running. The s a jet unit
should shut off. Press the “reset” button.
The s a jet unit should resume normal o er-
ation. If the s a jet unit continues to run after
the “test” button is ressed, then the GFCI is
damaged. Do not use the RENEW 900 until
the GFCI has been re aired or re laced by a
qualified electrician.

4
20. Kee all electrical a liances such as radios,
tele hones, televisions, and lights at least
five feet (1.52 meters) away from the water.
21. A wire connector is rovided on the um
motor of this unit to connect a minimum No.
8 AWG (804 mm2) solid co er conductor
between this unit and any metal equi ment,
electrical enclosure made of metal, metal
water i es, or conduit within five feet
(1.52m) of the unit.
22. DANGER—Risk of electric shock: Do not set
u the RENEW 900 within five feet of any
metal objects or surfaces. As an alternative,
you may use the RENEW 900 within five feet
of metal objects if each metal object is er-
manently connected to the wire connector on
the um motor of this unit by a minimum
No. 8 AWG (804 mm2) solid co er conductor
(see instruction 21).
23. DANGER—Risk of drowning: Exercise
extreme caution to revent unauthorized and
unsu ervised use of the RENEW 900 by chil-
dren. Children must always be su ervised.
24. DANGER—To reduce the risk of drowning:
• Never use the RENEW 900 alone;
• Children should not use the RENEW 900
unless they are su ervised by an adult;
• Kee ets away from the RENEW 900 at all
times;
• Always re lace and lock the s a cover
when the RENEW 900 is not in use.
25. WARNING—To reduce the risk of injury: The
water tem erature should never exceed
104°F (40°C). Tem eratures between 100°F
(38°C) and 104°F (40°C) are considered to be
safe for healthy adults. However, if you lan
to remain in the RENEW 900 for more than
10 to 15 minutes, a lower tem erature is rec-
ommended. Lower tem eratures are also rec-
ommended for children.
26. WARNING—To reduce the risk of injury:
Always use an accurate thermometer to
determine the water tem erature before
using the RENEW 900.
27. WARNING—To reduce the risk of injury:
Pregnant women should consult with their
hysician before using the RENEW 900.
Pregnant women should not use the RENEW
900 if the water tem erature is above 100°F
(38°C); the unborn child could be seriously
harmed.
28. DANGER—To reduce the risk of drowning:
Prolonged immersion in the RENEW 900 may
cause hy erthermia, a dangerous condition
which occurs when the internal body tem er-
ature rises several degrees above the normal
body tem erature of 98.6°F. The sym toms of
hy erthermia are nausea, dizziness, drowsi-
ness, and fainting. Effects include: a lack of
awareness, inability to erceive heat or dan-
ger, and a greater risk of drowning due to a
loss of consciousness. Special note:
Individuals suffering from hyperthermia may
be unable to realize that they must exit the
RENEW 9 , and they also may be physically
unable to do so.
29. WARNING—To reduce the risk of drowning:
Heat from the water, in conjunction with alco-
hol or drugs can cause unconsciousness. Do
not use the RENEW 9 if you are under the
influence of drugs or alcohol.
30. WARNING—To reduce the risk of injury or
drowning: Consult your hysician about os-
sible side-effects of any medications you may
be taking before using the RENEW 900. Heat
from the water, in conjunction with some med-
ications may cause drowsiness and increase
the risk of drowning. Others can effect blood
ressure, heart rate, and circulation.
31. WARNING—To reduce the risk of injury: It is
es ecially im ortant for ersons over the age
of 35 or ersons with re-existing health
roblems, such as obesity, heart disease,
high or low blood ressure, circulatory rob-
lems, or diabetes to consult your hysician
before using this roduct.
32. If you feel ain or dizziness at any time while
using the RENEW 900, discontinue use and
contact a hysician.
WARNING: Read all instructions before using the RENEW 900. ICON assumes no res onsibility for
ersonal injury or ro erty damage sustained by or through the use of this roduct.
SAVE THESE INSTRUCTIONS

5
WARNING DECAL PLACEMENT
The decals shown below have been laced on the RENEW 900. If a decal is missing, or if it is not legible,
lease call our Customer Service De artment toll-free at 1-888-936-4266, Monday–Thursday, 8:00
am–6:30 m; Friday, 8:00 am–6:00 m EST (excluding holidays), to order a re lacement decal. A ly the
decal in the location shown.
IMAGE®is a registered trademark of ICON Health & Fitness, Inc.

6
BEFORE YOU BEGIN
hank you for selecting the IMAGE®RENEW 900. he
innovative RENEW 900 offers the features and quality
of a traditional hot tub at an affordable price. Best of
all, the RENEW 900 is fully portable, so you can take
it wherever there is an electrical outlet. he RENEW
900 allows you to relax and unwind in the comfort of
your own home.
For your benefit, read this manual carefully before
using the IMAGE®RENEW 900. If you have addition-
al questions, please call our Customer Service
Department toll-free at 1-888-936-4266, Monday–
hursday, 8:00 am–6:30 pm; Friday, 8:00 am–6:00 pm
ES (excluding holidays). o help us assist you,
please note the product model number and serial
number before calling. he model number is
831.100430. he serial number can be found on a
decal attached to spa jet unit (see the front cover of
this manual).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Spa Jet Unit
Inflation Valve
Side Panel
Locking Buckle
Console (Under
Spa Cover)
Spa Cover
Power Cord
Ground Fault Circuit
Interrupter (GFCI)

7
CHOOSING A LOCATION FOR THE RENEW 900
here are many factors to consider when choosing a location to set up the RENEW 900. hese factors vary
depending on whether you use the RENEW 900 inside or outside. We have listed several factors you may wish
to consider as you decide where you want to use the RENEW 900.
If you set u the RENEW 900 inside:
1. he RENEW 900 will increase the level of humidi-
ty in your home. he location you choose should
be well ventilated. You may need to install a venti-
lation fan or use a dehumidifier.
2. he location must be close to an electrical outlet.
Do not use an extension cord with the RENEW
900.
3. he RENEW 900 should be close to a source of
water.
4. Do not use the RENEW 900 on carpet or other
material that may be damaged by moisture. We
recommend that you place the RENEW 900 on a
water- and stain-resistant, non-slip surface with a
floor drain for any water that may splash from the
RENEW 900.
5. Be sure that the location you choose is stable. It
must be able to support the weight of the RENEW
900 when it is filled with water, plus the weight of
the occupants. he RENEW 900 weighs approxi-
mately 2400 pounds when filled with water.
6. Do not use the RENEW 900 above a finished liv-
ing area, due to the risk of water damage.
7. Be sure that there is room around the RENEW
900 to permit servicing of the unit. he diameter of
the tub is 69”. You should allow for this size, plus
the size of the spa jet unit, when choosing the
location.
8. Be sure to note any other considerations, such as
aesthetics or privacy concerns, that may affect the
safety or enjoyment of using the RENEW 900.
If you set u the RENEW 900 outside:
1. You should check your local building codes con-
cerning the use of outdoor spas.
2. he location must be close to an electrical outlet.
Do not use an extension cord with the RENEW
900.
3. he RENEW 900 should be close to a source of
water.
4. We recommend that you place the RENEW 900
on a water- and stain-resistant, non-slip surface.
5. Be sure that the location you choose is stable. It
must be able to support the weight of the RENEW
900 when it is filled with water, plus the weight of
the occupants. he RENEW 900 weighs approxi-
mately 2400 pounds when filled with water.
6. hink about environmental factors, such as rain,
wind, shade, sunlight, and so forth.
7. You should be able to monitor the use of the
RENEW 900 from your home, to prevent unautho-
rized use by children.
8. Be sure that there is room around the RENEW
900 to permit servicing of the unit. he diameter of
the tub is 69”. You should allow for this size, plus
the size of the spa jet unit, when choosing the
location.
9. Be sure to note any other considerations, such as
aesthetics or privacy concerns, which may affect
the safety or enjoyment of using the RENEW 900.

8
1. Before beginning assembly, be sure that you
have read and understand the information in the
box above and on the revious age.
Unfold the pre-assembled Fabric Spa Surround (8)
and Side Panels (1, 2) until the assembled unit is
round.
Check the self-attaching connections between the
Fabric Spa Surround (8) and Side Panels (1, 2) to
be sure that all connections are firm. Be sure that all
six cover buckles are fully inserted through the slots
in the Side Panels (1, 2).
2. Unfold the Inflatable Spa Liner (9).
Attach the nozzle on the included air pump to the
valve on the side of the Inflatable Spa Liner (9). Use
the air pump to fill the sides of the Inflatable Spa
Liner with air.
Attach the nozzle on the air pump to the valve on
the floor of the Inflatable Spa Liner (9). Use the air
pump to fill the bottom of the Inflatable Spa Liner
with air.
Attach the nozzle on the air pump to the valve on
top of the Inflatable Spa Liner (9). Use the air pump
to fill the cushion on top of the Inflatable Spa Liner
with air.
3. Be sure that the flap on the Fabric Spa Surround (8)
is on the outside of the Fabric Spa Surround and
Side Panels (1, 2). Insert the Inflatable Spa Liner (9)
into the Fabric Spa Surround. Align the valve in the
Inflatable Spa Liner with the hole in the Fabric Spa
Surround and the Inflation Side Panel (2).
Flip the flap on the Fabric Spa Surround (8) over the
low section of the Inflatable Spa Liner (9).
3
1
9
1, 2
8—Flap
Valve must
be visible in
this hole
8
Buckle
Slot
1, 2
2
ASSEMBLY
Before beginning assembly, carefully read the
following information and instructions:
• Place all parts in a cleared area and remove the
packing materials; do not dispose of the packing
materials until assembly is completed.
• Assembly requires two people.
• Assembly requires the included air pump.
• Read each assembly step before you begin.
• During assembly, make sure that all parts are ori-
ented as shown in the drawings.
9
Inflate here
first
Inflate here
third
Inflate here
second

9
4. Remove the power cord from the Spa Jet Unit (13).
With the help of a second person, place the Spa Jet
Unit (13) over the Side Panel (1) and the section of
the Inflatable Spa Liner (9) which does not have the
cushion. Be extremely careful not to tear the
Inflatable S a Liner (9) as you slide the S a Jet
Unit into lace.
5. Before you fill the RENEW 900, be sure that it is in
the position you want, and that it can be easily ser-
viced, if needed. Once the RENEW 900 is filled with
water, it will need to be drained to be moved.
Using a garden hose or other clean water source,
begin filling the RENEW 900, until the jet and filter
openings on the Spa Jet Unit (13) are covered with
water. Do not fill the RENEW 900 more than 20”
dee with water.
After the RENEW 900 is full, you must rime the
S a Jet Unit (13) before using the RENEW 900
(see PRIMING THE SPA JET UNIT on age 10).
6. Attach the nozzle on the included air pump to the
valve on the Inflatable Cover (4). Use the Air Pump
to fill the Inflatable Cover (4) with air. Remove the
nozzle from the Inflatable Cover.
Slide one of the straps on the inside of the Spa
Cover (11) through one of the loops on the
Inflatable Cover (4). Attach the latch on the strap to
the buckle on the other end.
Attach the other three straps on the inside of the
Spa Cover (11) through the loops on the Inflatable
Cover (4) in the same manner.
7. Place the Spa Cover (11) over the Side Panels (1,
2) and the Spa Jet Unit (13). Be sure that the S a
Cover is ro erly centered and that the stra s
on the S a Cover line u with the stra s extend-
ing from the slots in the Side Panels (1, 2).
Snap each of the six latches on the Spa Cover (11)
into the buckles on the straps extending from the
slots in the Side Panels (1, 2).
7
4
5
64
11
1
9
13
13
9
Power
Cord
1, 2
11
13
Latches and Buckles
Latch and
Buckle

10
USING THE RENEW 900
he RENEW 900 is designed for up to four adults.
he six water jets can be regulated to provide a relax-
ing massage to sooth away stress, and the strength
of the water massage can be adjusted by the air con-
trol. he RENEW 900 holds 300 gallons of water and
offers an automatic, programmable heating (70°F to
104°F) and filtration system.
he guidelines below explain how to properly use the
RENEW 900. Follow these guidelines to maintain the
RENEW 900 for your long-term enjoyment.
PRIMING THE SPA JET UNIT
he water pump in the spa jet unit must be primed
before you use the RENEW 900 the first time. You
must also prime the pump before using the unit each
time you re-fill the RENEW 900.
o prime the spa jet
unit, remove the
primer cap from the
console. Fill the spa
jet unit with at least 64
oz. of water. Re lace
and tighten the
rimer ca . IMPOR-
TANT: The s a jet
unit may be seriously damaged if the um is not
ro erly rimed, or if the rimer ca is not
re laced and fully tightened.
PLUGGING IN THE RENEW 900
Once the RENEW 900 is filled with enough water to
cover the water jets and the pump has been primed,
the power cord can be plugged in and the spa jet unit
can be turned on. Note: he first time the power cord
is plugged in, the spa jet unit will turn on automatically.
When connecting the power cord, plug the power cord
directly into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on the
same circuit. Replace the power cord immediately if it
becomes damaged.
he power cord is equipped with a Ground Fault
Circuit Interrupter (GFCI), located at the end of the
power cord. You should always test the GFCI before
using the RENEW 900.
First, turn on the RENEW 900 by pressing the power
button on the console. Once the unit is running, press
the GFCI “test” button. he RENEW 900 should shut
off. Press the “reset” button. he RENEW 900 should
resume normal operation. If the RENEW 900 contin-
ues to run after the “test” button is pressed, then the
GFCI is damaged. Do not use the RENEW 900 until
the GFCI has been repaired or replaced by a qualified
electrician.
STARTING THE RENEW 900
Once you have tested the GFCI, you should verify the
water flow from the pumping unit. Set the air control
on the console to the lowest setting (see USING HE
CONSOLE on the next page). he pumping unit will
heat the water as it pumps. Cover the RENEW 900
with the spa cover. The s a cover must be tight.
he water will heat at about 1.7°F an hour with the
cover on. If you are using the RENEW 900 indoors,
and the room temperature is maintained at 70°F, it will
take approximately 20 to 28 hours for the water to
reach the set temperature.
he temperature and water flow can be set or
changed by the controls on the console (see USING
HE CONSOLE on the next page).
TESTING AND TREATING THE WATER
he RENEW 900 comes with a starter chemical pack
for maintaining the water in the spa. Disregard the
directions on the individual packages of “QUICK pHix
It DOWN” and “QUICK pHix It UP.” However, the
directions on the bottle of “Non-chlorine Shox” and
“Bromine Base” are correct. Always kee the chemi-
cals away from children and ets.
he first time you use the spa, you should test and
treat the water. Once you have verified that the spa
jet unit is functioning properly, and have allowed the
water to circulate for a while, you should remove the
spa cover and add 1/3 of the “Bromine Base” bottle,
and 1/3 of the “Non-chlorine Shox” bottle to the water
in the spa. Allow the water to circulate for five min-
utes. You should now test the pH level of the water.
Use the included test strips to check the pH of the
est and Reset
Buttons
Grounded circuit capable of
carrying 15 or more amps
GFCI
Primer
Cap

11
water. Refer to the instructions on the test strip pack-
aging to see how to use the test strips.
If the level is too low, add half of one of the “QUICK
pHix It UP” packets to the water. Let the water circu-
late through the spa jet unit for five minutes. est the
pH level again. Repeat until the pH level is correct.
If the level is too high, add half of one of the “QUICK
pHix It DOWN” packets to the water. Let the water cir-
culate through the spa jet unit for five minutes. est
the pH level again. Repeat until the pH level is correct.
Replace the spa cover and allow the water to contin-
ue to heat.
See WA ER CHEMIS RY on page 13 for information
concerning proper water maintenance.
SECURING THE SPA COVER
he spa cover can be secured by snapping the latch-
es on the spa cover into the buckles on the side panels.
he buckles can be
locked by inserting the
key and turning it
clockwise a quarter
turn. o unlock the
buckles, insert the key
and turn it counter-
clockwise a quarter
turn.
Always kee the buckles locked when the s a is
not in use. Kee the keys in a safe lace, out of
the reach of children.
USING THE CONSOLE
Refer to the console diagram above. he function of
each console control is explained below:
Primer: his opening allows you to prime the spa jet
unit before operation (see PRIMING HE SPA JE
UNI on page 10).
Diverter: Controls the flow of water through the
hydro-therapy jets and the whirlpool jet. he direction
of the flow can be adjusted by turning the diverter
control. When the control is set to “front,” the flow will
be through the hydro-therapy jets; when it is set to
“side,” the flow will be through the whirlpool jet; when
it is set to “all,” the flow will be evenly distributed
through both the hydro-therapy jets and the whirlpool
jet.
Thermostat: Controls the temperature of the water.
he water heats at about 1.7°F an hour with the cover
on. he thermostat can be set to heat the water from
70°F to 104°F. Use a medical or other accurate ther-
mometer to check the temperature of the water.
On/Off: urns the spa jet unit on and off. When you
first press the on/off button, the spa jet unit will run at
low speed, providing gentle hydrotherapy. Press the
button again and the spa jet unit will run at high
speed, providing more intense hydrotherapy. Press
the button a third time and the spa jet unit will shut
off.
he spa jet unit also features an automatic mode,
which heats and filters the water when the spa is left
unattended. When the spa jet unit is first plugged in,
or if the buttons on the console have not been used
for longer than twenty minutes, the automatic mode
will begin filtering or heating the water, as needed.
Note: to kee the filter and heat cycles from run-
ning, the ower cord must be un lugged.
Air Control: Determines the amount of air that is in
the spa jet system during operation. If the control is
turned to the left, the amount of air flowing through
the jets will increase. If the control is turned to the
right, the amount will decrease.
DIAGRAM OF THE CONSOLE
Key
Latch
Buckle

12
SPA JET UNIT OPERATION
he spa jet unit features five hydro-therapy jets, a
whirlpool jet, a suction vent, and a filter housing.
he five hydro-thera y jets (A), located on the front
of the spa jet unit, focus the water massage on your
neck and back.
he whirl ool jet (B), located on the left side of the
spa jet unit, directs the flow of the water to create a
whirlpool action in the RENEW 900.
he suction vent (C),
located on the right
side of the spa jet
unit, pulls the water
into the spa unit, in
order to operate the
system. he suction
cover should always
be in place over the
suction vent. Never
o erate the RENEW
900 without the suc-
tion cover in lace.
he filter (D), is locat-
ed on the left side of
the spa jet unit,
behind the filter cover.
he filter can be
removed for cleaning
and replacement by
removing the Filter
Cover and the two
filter cover screws and then pulling the filter from the
spa jet unit.
he spa jet unit features an automatic filter cycle and
freeze protection. If the spa jet unit has not been
operated for three hours, the pump will begin circulat-
ing the water for twenty minutes to filter any impuri-
ties. Also, if the water temperature falls below 40°F,
the pump will begin circulating and heating the water
to prevent the water from freezing.
DRAINING THE RENEW 900
o drain the RENEW 900, you must use a garden
hose to siphon the water. Place one end of the hose
in the RENEW 900 and hold it in front of a hydro-
therapy jet until there is a flow of water coming out of
the hose. Turn off the s a unit and un lug the
ower cord. The unit will be damaged if it is run
without water circulating. Be sure the end of the
hose in the RENEW 900 is on the floor of the spa.
DRAINING THE PUMP
After the RENEW 900 is drained (see DRAINING
HE RENEW 900 above), the pump in the spa jet unit
should also be drained if the RENEW 900 will be
stored for more than thirty days, or if it may be
exposed to freezing temperatures.
o drain the pump,
remove the spa jet
unit from the side pan-
els. Be careful not to
tear the inflatable
s a liner. Locate the
pump inside the spa
jet unit. Remove the
drain plug from the
pump. ip the spa jet
unit slightly, until all the water has drained from the
pump. Replace the drain plug.
Drain Plug
Pump
A
B
D
C
C
Filter Cover
Screws
Filter Cover
D

13
CLEANING THE INFLATABLE SPA LINER
he liner should be cleaned with a mild soap solution.
Do not use solvents. he liner should always be clean
and dry before being moved or stored.
CHECKING AND CLEANING THE FILTER
he filter should be checked periodically for build-up
of dirt and oil. If the filter needs to be cleaned, follow
the steps below:
1. urn off the power.
2. Remove the two screws and cover from the
spa jet. hen pull the filter out of the unit.
3. Check the filter for any dirt or debris. If the fil-
ter needs to be cleaned, rinse the filter with a
hose. If the filter still is dirty, you will need to
soak it in a cleaning solution which can be
obtained from a pool and spa supply store.
4. Inspect the filter for damage. Replace the fil-
ter if there are any signs of damage.
5. Re-insert the cleaned filter and re-attach the
two screws and cover to the spa jet unit.
MAINTAINING THE SPA COVER
he spa cover should be cleaned monthly. Remove
the inflatable cover from the spa cover, then hang the
spa cover over a clothes line and spray it with a hose.
Leave the cover on the clothes line until it is fully dry.
WINTER USE AND CARE
he RENEW 900 is designed for year-round use. If
you decide to store the RENEW 900 for the winter,
store it in a warm, dry location. (See DRAINING HE
RENEW 900 and DRAINING HE PUMP on page 12.)
WATER CHEMISTRY
he RENEW 900 comes with a starter chemical pack
for maintaining the water in the spa. (See ES ING
AND REA ING HE WA ER on page 10.) Additional
chemicals can be purchased at a pool and spa supply
store.
CAUTION: The chemicals used to maintain the H
balance of the water and to sanitize the water can
be dangerous. Always follow these basic guide-
lines when handling the chemicals:
1. Always read and follow the directions on
the label, unless directed otherwise.
2. Never mix different chemicals.
3. Do not exceed the recommended
amounts—follow the directions on the
label closely.
4. Kee all chemicals out of the reach of chil-
dren and ets.
5. Kee all containers closed tightly when
not in use.
6. Never add water to the chemicals—always
add the chemicals to the water as directed.
7. Always store chemicals in a cool, dry lace.
8. Always kee chemicals away from chil-
dren and ets.
MAINTAINING THE PROPER PH BALANCE
he pH factor is a measure of relative acidity or alka-
linity in the water. It is measured on a scale of 1 to 14.
Pure water has a value of 7, which is neutral. Any
value above 7 is alkaline, and any value below 7 is
acidic. You should maintain a slightly alkaline pH
level, between 7.2 and 7.8, in the RENEW 900.
Severe problems can occur when the pH balance is
not maintained within this range. If the pH level
exceeds 7.8, dissolved minerals can build-up and clog
the plumbing in the spa jet unit. If the pH level falls
below 7.2, the acid level in the water will begin to cor-
rode the metal parts in the spa jet unit. Also, the sani-
tation agents in the water will not be effective if the pH
level is not properly maintained. Damage caused by
improper pH levels is not covered under the warranty.
o maintain the proper pH level, you should test the
pH of the water regularly. o test the water you can
either purchase additional test strips or purchase a pH
test kit at a pool and spa supply store. he pH read-
ing should be between 7.2 and 7.8. If the level is too
low, add a pH increaser (usually soda ash). If the
level is too high, add a pH reducer (usually sodium
bisulfate). est the water again after five minutes. See
the instructions with your test strips or pH test kit for
additional information about testing and adjusting the
pH.
SANITIZING THE RENEW 900
Please refer to your local pool and spa supplier for
information concerning which chemicals you should
use in your area to sanitize the spa.
he most common sanitizing agent is a solid bromine
concentrate. he amount required varies according to
several factors, such as user load, temperature, water
conditions, and so forth.
Proper water maintenance is a fairly complex process.
We recommend that you contact your local pool and
spa supplier for information on how you should best
accomplish this.
MAINTENANCE

14
1. SYMPTOM: THE SPA WILL NOT OPERATE
a. Check the power cord. he power cord must
be plugged into a grounded outlet (see PLUG-
GING IN HE RENEW 900 on page 10).
b. Check to see if the GFCI breaker is tripped, or
was not turned on. Reset the GFCI breaker.
2. SYMPTOM: THE CIRCUIT BREAKER OR GFCI
BREAKER TRIPS WHILE THE SPA IS
OPERATING
a. Reset the circuit breaker. If the circuit breaker
trips again, contact a qualified electrician for
service.
3. SYMPTOM: THE PUMP HUMS
a. he filter may be dirty or damaged. Remove
the filter housing from the spa jet unit and clean
or replace the filter.
b. he pump may have a foreign object stuck in
the impeller. Contact our customer service
department.
c. he pump may have a loose wire connection.
Contact our customer service department.
4. SYMPTOM: THE PUMP HUMS BUT DOES NOT
ROTATE
a. he pump may be jammed. Contact our cus-
tomer service department.
5. SYMPTOM: THE PUMP IS NOISY WHILE
OPERATING
a. here may be debris in the pump. Contact our
customer service department.
b. he pump may have a bad bearing. Contact
our customer service department.
6. SYMPTOM: THE WATER DOES NOT HEAT
a. he heater is attached to the pump in the spa
jet unit. If the pump is operating, the water
should heat. Cover the RENEW 900 with the
spa cover. The s a cover must be tight. Set
the air control to low. he water will heat at a
rate of 1.7°F an hour. If you are using the spa
indoors, and the room temperature is main-
tained at 70°F, it will take approximately 20 to
28 hours for the water to reach the set temper-
ature.
b. If you are using the RENEW 900 outdoors, it
may take longer for the water to heat. See the
chart below for the approximate heating time.
Air emperature Heating ime
70°F +20 to 28 hours
50°F–70°F 1 to 2 days
30°F–50°F 2 to 3 days
b. If the water still has not heated after three
days, contact our customer service department.
7. SYMPTOM: THE WATER PULSATES OR
THERE IS MINIMUM WATER FLOW
a. Adjust the water level. his usually occurs only
when the water level is low. Add water until the
filter and jets are covered.
b. his problem is caused by excess air in the
pump circulation system. Check to see if the
primer cap is fully tightened. Prime the pump
again and fully tighten the primer cap (see
PRIMING HE SPA JE UNI on page 10).
8. SYMPTOM: THE SPA JET UNIT CAVITATES
DURING USE
a. Adjust the water level. his usually occurs only
when the water level is low. Add water until the
filter and jets are covered.
b. his problem is caused by excess air in the
pump circulation system. Check to see if the
primer cap is fully tightened. Prime the pump
again and fully tighten the primer cap (see
PRIMING HE SPA JE UNI on page 10).
9. SYMPTOM: THE WATER IS NOT BEING
CLEANED BY THE FILTER
a. Check to see if the filter is in place. Clean the
filter if it is dirty.
TROUBLE-SHOOTING
Most roblems can be solved by following the sim le ste s below. Find the sym tom that a lies, and
follow the ste s listed. If further assistance is needed, call our Customer Service De artment toll-free
at 1-888-936-4266, Monday–Thursday, 8:00 am–6:30 m; Friday, 8:00 am–6:00 m EST (excluding holi-
days).

15
b. Check the chemical balance of the water. If the
pH is incorrect, the sanitizing agents will not
function properly.
10. SYMPTOM: THE SPA JET UNIT CONTINUES
TO RUN AFTER IT HAS BEEN SHUT OFF
a. When you press the on/off button once, the spa
jet unit will run at low speed, heating the water.
Press the button again and the spa jet unit will
run at high speed, filtering the water. Press the
button a third time and the spa jet unit will shut
off. he spa jet unit also features an automatic
mode, which heats and filters the water when
the spa is left unattended. When the spa jet
unit is first plugged in, or if the buttons on the
console have not been used for longer than
twenty minutes, the automatic mode will begin
filtering or heating the water, as needed. o
keep the filter and heat cycles from running,
the power cord must be unplugged. S ecial
Note: If the unit is to be ke t outdoors in
cold weather, you must allow the s a to
maintain a safe tem erature by running in
automatic mode. Allowing the s a jet unit to
freeze will damage the unit. If you do not
want to use the s a during the winter, store
it in a warm, dry location (see WINTER USE
AND CARE on age 13).
11. SYMPTOM: THE WATER LEVEL DROPS
a. Some water loss due to evaporation is normal.
If rapid water loss occurs, or if you notice wet-
ness on the floor around the RENEW 900, then
the liner may have a leak. Locate the leak, and
patch it using a pool patch kit that you can pur-
chase at any pool and spa supply store.
b. A clamp or seal inside the spa jet may be
loose. Check the floor around the spa jet unit
for excess water, and watch the spa jet unit
while it is operating to see if water drips from
the spa jet unit housing. If you can identify the
location of the leak inside the spa jet unit, tight-
en the clamp or replace the damaged seal.
12. SYMPTOM: THE INFLATABLE SPA LINER
LOSES AIR
a. Over time, some air loss is normal. If rapid air
loss occurs, then the liner may have an air
leak. Locate the leak, and patch it using a pool
patch kit that you can purchase at any pool and
spa supply store.

Part No. 154868 J00726-C R0499A Printed in USA © 1999 ICON Health & Fitness, Inc.
ORDERING REPLACEMENT PARTS
o order replacement parts, simply call our Customer Service Department toll-free at 1-888-936-4266,
Monday– hursday, 8:00 am–6:30 pm; Friday, 8:00 am–6:00 pm ES (excluding holidays). o help us assist you,
please be prepared to give the following information when calling:
1. he MODEL NUMBER of the product (831.100430).
2. he NAME of the product (IMAGE®RENEW 900).
3. he SERIAL NUMBER of the product (see the front cover of this manual).
4. he KEY NUMBER and DESCRIP ION of the part(s) (see the PAR LIS /EXPLODED DRAWING attached to
the center of this manual).
16

18
CUSTOMER RECORD
Model No.: Serial No.:
Retailer Name: Purchase Date:
Retailer Address:
ICON of Canada Inc.
900 de l’Industrie
St-Jérôme, Québec
Canada, J7Y 4B8
PLACE
STAMP
HERE

17
IMPOR AN : MAIL WI HIN 14 DAYS OF PURCHASE
NAME:
ADDRESS:
COUN Y:
MODEL NO.
RE AILER NAME:
PHONE:
POS CODE:
SERIAL NO. PURCHASE DA E:
RE AILER ADDRESS:
1) Primary user(s) of product:
❏ Male ❏ Female ❏ Family
2) Age of primary user:
❏ 0–24 ❏35–44 ❏55–64
❏25–34 ❏45–54 ❏65 and over
3) Annual household income:
❏0–9,999 ❏15,000–19,999
❏10,000–14,999 ❏20,000+
4) How many times a week do you exercise?
❏Less than 3 times ❏3 times or more
5) Have you ever purchased an ICON product before?
❏Yes ❏No
6) Where did you first see or hear about ICON products?
❏Magazine ❏Friend/relative
❏Newspaper Ad ❏Store
❏Other
7) What was the primary reason for purchasing this ICON product?
❏Store Employee ❏elevision Ads ❏Colour
❏Electronic Features ❏Magazine Ads ❏Price
❏Product Design ❏Product Innovation
❏Other Features
8) Did you consider purchasing fitness equipment from another
manufacturer?
❏No ❏Yes
What other Manufacturer?
9) Based on your impression of what you have purchased,
would you buy another ICON product?
❏Yes ❏No ❏No Opinion
If not, what other brand name equipment would you purchase?
10)What other type of exercise equipment do you own?
❏Bicycle ❏Exercise Cycle ❏readmill
❏Home Gym ❏Weight Bench ❏Stepper
❏Cardio Glide ❏Other
11) Which type of magazines do you read regularly?
❏Sports ❏Fitness ❏Motoring
❏Business ❏Computer ❏General
12) Do you wish to be sent further bulletins about ICON products?
❏Yes ❏No
HANK YOU FOR YOUR IME
of/du Canada Inc.
™
PRODUCT WARRANTY REGISTRATION
© 1999 ICON of Canada, Inc. Printed in USA
LIMITED FIVE YEAR MASSAGE SPA WARRANTY
ICON OF/DU CANADA INC., (ICON), warrants this product to be free from defects in workmanship and material, under nor-
mal use and service conditions, for a period of ninety (90) days from the date of purchase. ICON extends a limited five (5)
year warranty on the spa shell structure. ICON also extends a limited two (2) year warranty on the pump and motor. his
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at
ICON's option, the product through one of its authorized service centers. All repairs for which warranty claims are made must
be pre-authorized by ICON. his warranty does not extend to any product or damage to a product caused by or attributable
to freight damage, abuse, misuse, improper or abnormal usage, or repairs not provided by ICON authorized service per-
sonnel, to products used for commercial or rental purposes, or to products used as store display models. Specifically exclud-
ed are damages caused by or attributable to the following incidents: any damage to the wood exterior resulting from improp-
er maintenance, or any damage to the wood or tile exterior attributable to freight mishandling; damage resulting from improp-
er winterization; damage to the spa shell resulting from improper chemical treatment, damage to the spa shell resulting from
exposure to extreme temperatures, or damage to the spa shell resulting from exposure to direct sunlight and ultraviolet rays
while the spa is empty; damage to the pump, motor, plumbing, and components due to improper maintenance, chemical
treatment, or exposure; damage resulting from failure to properly follow user’s manual installation, operating, or mainte-
nance instructions. Also excluded are consumable components, including but not restricted to headrests, filter cartridges,
and light bulbs. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use
or performance of the product or damages with respect to any economic loss, loss of or damage to property including water
damage, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages
of whatsoever nature. Some provinces do not allow the exclusion or limitation of incidental or consequential damages.
Accordingly, the above limitation may not apply to you.
he warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or
fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some provinces do not allow
limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
his warranty gives you specific legal rights. You may also have other rights which vary from province to province.
ICON OF/DU CANADA, 900 de l’Industrie, St. Jerôme, QC J7Y 4B8

18
REFERENCES
No. du Modèle: No. de Série:
Nom du Détaillant: Date d’Achat:
Adresse du Détaillant:
ICON of/du Canada Inc.
900 de l’Industrie
St-Jérôme, Québec
Canada, J7Y 4B8
AFFRANCHIR
SUFFISAMMEN

17
IMPOR AN : POS EZ DANS LES 14 JOURS SUIVAN L’ACHA
NOM: ADRESSE:
PAYS:
NO. DE MODÈLE:
NOM DU DÉ AILLAN :
ÉLÉPHONE:
CODE POS AL:
NO. DE SÉRIE: DA E D’ACHA :
ADRESSE:
1) Usager principal du produit:
❏ Homme ❏ Femme ❏ Famille
2) Âge de l’usager principal:
❏ 0–24 ❏35–44 ❏55–64
❏25–34 ❏45–54 ❏65 et plus
3) Revenu annuel:
❏0–9,999 ❏15,000–19,999
❏10,000–14,999 ❏20,000+
4) Combien de fois par semaine faites-vous de l’exercice?
❏moins que 3 fois ❏3 fois et plus
5) Avez-vous déjà acheté un produit ICON?
❏Oui ❏Non
6) Comment avez-vous entendu parler des produits ICON?
❏Publicité dans un journal ❏Magasin
❏Magazine ❏Ami/Parent ❏Autre
7) Quel est votre raison principale pour avoir choisi un produit ICON?
❏Employé du magasin ❏Publicité à la télévision
❏Options électroniques ❏Publicité dans un magazine
❏Modèle du produit ❏Innovation du produit
❏Couleur ❏Prix ❏Autres aspects
8) Avez-vous déjà considéré l’achat d’un produit fabriqué par un
autre manufacturier?
❏Non ❏Oui
Si oui, lequel?
9) Basé sur votre impression du produit, achèteriez-vous un
autre produit ICON?
❏Oui ❏Non ❏Sans opinion
Sinon quelle marque achèteriez-vous?
10) Possédez-vous d’autre équipement d’exercice?
❏Bicyclette ❏Bicyclette stationnaire ❏apis
roulant
❏Appareil de musculation ❏Banc d’exercice
❏Simulateur d’escalier ❏Cardio Glide ❏Autre
11) Quel type de magazine lisez-vous régulièrement?
❏Sports ❏Général ❏Automobilisme
❏Affaires ❏Ordinateur ❏Mise en forme
12) Désirez-vous recevoir de l’information supplémentaire sur les
produits ICON?
❏Oui ❏Non
MERCI DE VO RE EMPS
1999 © ICON du/of Canada, Inc.
of/du Canada Inc.
™
FORMULAIRE DE GARANTIE DU PRODUIT
ICON du CANADA, Inc. (ICON), garantie que ce produit n’a aucun défaut de fabrication ou de matériaux, sous utilisation et main-
tenance normale, pour une période de quatre-vingt-dix (90) jours après la date d’achat de ce produit. ICON rallonge une garantie
limitée pendant cinq (5) ans sur la structure du jacuzzi. ICON rallonge aussi une garantie limitée de deux (2) ans pour la pompe
et le moteur. Cette garantie est rallongée seulement pour l’acheteur original. L’obligation d’ICON sous cette garantie est limitée
au remplacement ou aux réparations, au choix d’ICON, du produit par un des centres de service autorisés. outes réparations
qui sont soumises sous la garantie doivent être pré-approuvées par ICON. Cette garantie ne comprend pas les dommages
causés ou dues au transport, abus, mauvais usage, ou réparations faites par une personne non-autorisée par ICON, aux pro-
duits utilisés pour une utilisation commerciale ou pour la location, ou aux produits utilisés pour l’exposition en magasin. Les dom-
mages causés ou attribués aux incidents suivants sont exclus de la garantie: les dommages faits au bois du jacuzzi causés par
un mauvais entretien, ou tout dommage fait au bois ou aux panneaux extérieurs causés par un mauvais transport; les dommages
causés par le froid, la pluie ou le gel; les dommages faits à la structure du jacuzzi dues à un mauvais usage des produits chim-
iques, à des températures extrêmes, ou à une exposition prolongée aux rayons directes du soleil et des ultra-violet quand le
jacuzzi est vide; les dommages à la pompe, au moteur, à la canalisation et aux pièces dues à un mauvais entretien, aux produits
chimiques, ou à l’exposition; les dommages résultants de ne pas lire les instructions d’assemblage et de fonctionnement con-
tenus dans le livret d’instructions. Les pièces usables sont aussi exclus telles que, mais non restrictées à, appui-tête, cartouch-
es du filtre, et ampoules. ICON n’autorise aucune autre garantie à part celles spécifiquement mentionnées ci-dessus.
ICON ne pourra être tenu responsable d'aucun dommage indirect, spécial ou accessoire résultant ou ayant trait à l'utilisation ou
au fonctionnement du produit, aux pertes d'argent, de biens, de revenus ou de profits, aux pertes de jouissance, aux frais de
déménagement, d'installation ou à tous dommages accessoires de quelque nature qu'ils soient. Dans certaines provinces, il est
interdit d'exclure ou de restreindre la responsabilité pour les dommages indirects ou accessoires de sorte que la restriction qui
précède pourrait ne pas s'appliquer dans certains cas.
La présente garantie remplace toutes les garanties dont notamment les garanties implicites de valeur marchande ou d'aptitude
à un usage et est limitée dans sa durée et sa portée par les clauses spécifiques contenues dans la présente garantie. Certaines
provinces n'autorisent pas la restriction de la durée d'une garantie de sorte que la restriction qui précède pourrait ne pas s'appli-
quer dans certains cas ou spécifiés par votre détaillant d’équipement de sports.
Cette garantie vous confère des droits légaux spécifiques. Vous pouvez avoir d'autres droits qui peuvent varier d'une province à
l'autre ou spécifier par votre détaillant d’équipement de sports.
ICON OF/DU CANADA INC., 900 de l‘Industrie, St-Jérôme, QC, J7Y 4B8
GARANTIE LIMITÉE DE CINQ ANS