IMAO CP165-08001 User manual

Feature
・ Each clamping screw has commercially available O-ring to prevent rotation and keep the direction of arrow marking.
・O-ringshouldbereplacedbythecustomerwhenitisworn.
Size d
*) Lf Lf1M
CP165-08001 12 13 5.5 M 8×1.25
CP165-12001 18 19 6.5 M12×1.75
CP165-16001 22 23 8.0 M16×2.00
*)・The hole tolerance should be -0.010
-0.025  when Tapered
Clamping Screws are always mounted on the fixture
plate.Fixtureplateandtaperedbushingfittightlyand
keeptherepeatabilitywithoutchipincursion.
・TheholetoleranceshouldbeH7whenmountingon
workpiece.Taperedbushingcanbeeasilymounted/
removed.
How To Use
TaperedClampingScrews
Canbeusedforlocatingfixtureplateorworkpiece.
Clamping Screws
Canbeusedforjustclamping.
■Mounting-HoleDimension ■SpacingTolerance
Spacingtoleranceshouldbe±0.02forTapered
Clamping Screws.
**)Spacingtoleranceshouldbe±0.2for
Clamping Screws.
■Installation
1.Fullytightentheclamping
screwonfixtureplateor
workpiece.
2.Turnthescrewcounterclockwise
withinoneturnuntilthearrow
marking points downward.
(Thereisagapbetweenclamping
screwandtaperedbushing.)
3.Install the clamping screws into the
clampingmodules.
Note:Refertothenextpageforthe
layoutoftheproducts.
d
Lf1Lf
Spacing Tolerance ±0.02 **)
Tapered Clamping
Screw (Hook)
Tapered Bushing (Accurate)
Fixture Plate
Tapered Clamping
Screw
CP157-L
CP165-LH
CP165-L
CP157-L
Tapered Bushing (Accurate)
Gap
Clamping Screw
Fixture Plate / Workpiece
CP165-LH CP165-L
Fixture Plate / Workpiece
M

Note
Donotremovethehoistsuntiltheunit
fullyclamped.
Related Product
・CP160ClampingModules(Hook)
・ CP165-LHTaperedClampingScrews(Hook)
■ApplicationExample
Tightenthehooktypeclampingscrewfirstly.
Thefirstonebecomesthereference.
Theproductsshouldbepositionedasshownbelow.
CP165-LH CP165-L TaperedClampingScrewsand CP157-L TaperedBushings(Accurate)shouldbeused
together, and CP166-H CP166 Clamping Screws and CP157-STaperedBushings(Standard)arealso .
Note: Use CP166-HCP166 Clamping Screws when locating of workpiece is not necessary.
・ CP165-LTaperedClampingScrews
・ CP166-HClampingScrews(Hook)
・ CP166 Clamping Screws
Tapered Bushings
(Accurate)
Tapered Clamping Screws (Hook)
Tapered Clamping Screws
Tapered Clamping
Screws (Hook)
Tapered Clamping
Screws
Tapered Clamping
Screws (Hook)
Tapered Bushings (Accurate)
Tapered Clamping Screws (Hook)
Clamping Screws
Clamping Screws
Tapered Bushings (Accurate)
Tapered Clamping Screws (Hook)
Tapered Clamping
Screws (Hook)
Tapered Bushings (Standard)
Example 1
Example 2
Example 3
Tapered Bushings
(Accurate)
Tapered Clamping Screws (Hook)
Tapered Clamping Screws
Tapered Clamping
Screws (Hook)
Tapered Clamping
Screws
Tapered Clamping
Screws (Hook)
Tapered Bushings (Accurate)
Tapered Clamping Screws (Hook)
Clamping Screws
Clamping Screws
Tapered Bushings (Accurate)
Tapered Clamping Screws (Hook)
Tapered Clamping
Screws (Hook)
Tapered Bushings (Standard)
Example 1
Example 2
Example 3
Tapered Bushings
(Accurate)
Tapered Clamping Screws (Hook)
Tapered Clamping Screws
Tapered Clamping
Screws (Hook)
Tapered Clamping
Screws
Tapered Clamping
Screws (Hook)
Tapered Bushings (Accurate)
Tapered Clamping Screws (Hook)
Clamping Screws
Clamping Screws
Tapered Bushings (Accurate)
Tapered Clamping Screws (Hook)
Tapered Clamping
Screws (Hook)
Tapered Bushings (Standard)
Example 1
Example 2
Example 3